Pinion angle
Guest
Posts: n/a
Re: Re: Re: Pinion angle
Sno,
Thanks for citing examples, I stand corrected.
Carl
"SnoMan" <admin@snoman.com> wrote in message
news:3tgb431o02ce0mg77e6mvjfabmdvj1inn9@4ax.com...
> On Fri, 11 May 2007 17:47:24 -0700, "Carl S"
> <carlsaiyed@REMOVE.hotmail.com> wrote:
>
>>Wouldnt a CV on each end cause the shaft to flop up and down? I cant
>>imagine
>>4 joints on a single driveshaft...
>
>
> No more than he front drive axles on a front wheel drive car of
> truck with IFS. As far as strength, axle shafts handle more torque
> than any drive shaft. It is quite feasable and doable with correct
> design and parts.
> -----------------
> TheSnoMan.com
Thanks for citing examples, I stand corrected.
Carl
"SnoMan" <admin@snoman.com> wrote in message
news:3tgb431o02ce0mg77e6mvjfabmdvj1inn9@4ax.com...
> On Fri, 11 May 2007 17:47:24 -0700, "Carl S"
> <carlsaiyed@REMOVE.hotmail.com> wrote:
>
>>Wouldnt a CV on each end cause the shaft to flop up and down? I cant
>>imagine
>>4 joints on a single driveshaft...
>
>
> No more than he front drive axles on a front wheel drive car of
> truck with IFS. As far as strength, axle shafts handle more torque
> than any drive shaft. It is quite feasable and doable with correct
> design and parts.
> -----------------
> TheSnoMan.com
Guest
Posts: n/a
Re: Re: Re: Pinion angle
Sno,
Thanks for citing examples, I stand corrected.
Carl
"SnoMan" <admin@snoman.com> wrote in message
news:3tgb431o02ce0mg77e6mvjfabmdvj1inn9@4ax.com...
> On Fri, 11 May 2007 17:47:24 -0700, "Carl S"
> <carlsaiyed@REMOVE.hotmail.com> wrote:
>
>>Wouldnt a CV on each end cause the shaft to flop up and down? I cant
>>imagine
>>4 joints on a single driveshaft...
>
>
> No more than he front drive axles on a front wheel drive car of
> truck with IFS. As far as strength, axle shafts handle more torque
> than any drive shaft. It is quite feasable and doable with correct
> design and parts.
> -----------------
> TheSnoMan.com
Thanks for citing examples, I stand corrected.
Carl
"SnoMan" <admin@snoman.com> wrote in message
news:3tgb431o02ce0mg77e6mvjfabmdvj1inn9@4ax.com...
> On Fri, 11 May 2007 17:47:24 -0700, "Carl S"
> <carlsaiyed@REMOVE.hotmail.com> wrote:
>
>>Wouldnt a CV on each end cause the shaft to flop up and down? I cant
>>imagine
>>4 joints on a single driveshaft...
>
>
> No more than he front drive axles on a front wheel drive car of
> truck with IFS. As far as strength, axle shafts handle more torque
> than any drive shaft. It is quite feasable and doable with correct
> design and parts.
> -----------------
> TheSnoMan.com
Guest
Posts: n/a
Re: Re: Re: Pinion angle
Sno,
Thanks for citing examples, I stand corrected.
Carl
"SnoMan" <admin@snoman.com> wrote in message
news:3tgb431o02ce0mg77e6mvjfabmdvj1inn9@4ax.com...
> On Fri, 11 May 2007 17:47:24 -0700, "Carl S"
> <carlsaiyed@REMOVE.hotmail.com> wrote:
>
>>Wouldnt a CV on each end cause the shaft to flop up and down? I cant
>>imagine
>>4 joints on a single driveshaft...
>
>
> No more than he front drive axles on a front wheel drive car of
> truck with IFS. As far as strength, axle shafts handle more torque
> than any drive shaft. It is quite feasable and doable with correct
> design and parts.
> -----------------
> TheSnoMan.com
Thanks for citing examples, I stand corrected.
Carl
"SnoMan" <admin@snoman.com> wrote in message
news:3tgb431o02ce0mg77e6mvjfabmdvj1inn9@4ax.com...
> On Fri, 11 May 2007 17:47:24 -0700, "Carl S"
> <carlsaiyed@REMOVE.hotmail.com> wrote:
>
>>Wouldnt a CV on each end cause the shaft to flop up and down? I cant
>>imagine
>>4 joints on a single driveshaft...
>
>
> No more than he front drive axles on a front wheel drive car of
> truck with IFS. As far as strength, axle shafts handle more torque
> than any drive shaft. It is quite feasable and doable with correct
> design and parts.
> -----------------
> TheSnoMan.com
Thread
Thread Starter
Forum
Replies
Last Post
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
