1988 Jeep Comanche clutch hydraulic fluid ?
Guest
Posts: n/a
1988 Jeep Comanche clutch hydraulic fluid ?
I just got this Jeep I was told the clutch was just replaced , I can
see the master cylinder is new , the fluid was dirty so I drained it
out and replaced it I was told that Dot 3 brake fluid was fine by the
NAPA guy, now my clutch works but makes a "rattling sound" when fully
engaged , tried bleeding off the system , the 2 lines that come out of
the Bell-housing are not secure must be a part missing that holds them
the line with the bleeder valve can be pushed in and out , need
schematic to see if part is missing, any help will be greatly
appreciated
Curt
see the master cylinder is new , the fluid was dirty so I drained it
out and replaced it I was told that Dot 3 brake fluid was fine by the
NAPA guy, now my clutch works but makes a "rattling sound" when fully
engaged , tried bleeding off the system , the 2 lines that come out of
the Bell-housing are not secure must be a part missing that holds them
the line with the bleeder valve can be pushed in and out , need
schematic to see if part is missing, any help will be greatly
appreciated
Curt
Guest
Posts: n/a
Re: 1988 Jeep Comanche clutch hydraulic fluid ?
The rattle is normally the throw out bearing which is part of the slave
cylinder which normally only comes as an expensive kit that includes the
master cylinder and costs about $800.00 to replace.... I did manage to
just find a master for my 88 so that is all I changed. I have the
rattle and now a leak in my slave cylinder. It is waiting until I can
do the whole clutch or more likely sell the Jeep because I can't do my
own work anymore.
They put a new clutch in and left all the old crappy slave and throw out
in there???? If so, they/you got took.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
ctops wrote:
>
> I just got this Jeep I was told the clutch was just replaced , I can
> see the master cylinder is new , the fluid was dirty so I drained it
> out and replaced it I was told that Dot 3 brake fluid was fine by the
> NAPA guy, now my clutch works but makes a "rattling sound" when fully
> engaged , tried bleeding off the system , the 2 lines that come out of
> the Bell-housing are not secure must be a part missing that holds them
> the line with the bleeder valve can be pushed in and out , need
> schematic to see if part is missing, any help will be greatly
> appreciated
> Curt
cylinder which normally only comes as an expensive kit that includes the
master cylinder and costs about $800.00 to replace.... I did manage to
just find a master for my 88 so that is all I changed. I have the
rattle and now a leak in my slave cylinder. It is waiting until I can
do the whole clutch or more likely sell the Jeep because I can't do my
own work anymore.
They put a new clutch in and left all the old crappy slave and throw out
in there???? If so, they/you got took.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
ctops wrote:
>
> I just got this Jeep I was told the clutch was just replaced , I can
> see the master cylinder is new , the fluid was dirty so I drained it
> out and replaced it I was told that Dot 3 brake fluid was fine by the
> NAPA guy, now my clutch works but makes a "rattling sound" when fully
> engaged , tried bleeding off the system , the 2 lines that come out of
> the Bell-housing are not secure must be a part missing that holds them
> the line with the bleeder valve can be pushed in and out , need
> schematic to see if part is missing, any help will be greatly
> appreciated
> Curt
Guest
Posts: n/a
Re: 1988 Jeep Comanche clutch hydraulic fluid ?
The rattle is normally the throw out bearing which is part of the slave
cylinder which normally only comes as an expensive kit that includes the
master cylinder and costs about $800.00 to replace.... I did manage to
just find a master for my 88 so that is all I changed. I have the
rattle and now a leak in my slave cylinder. It is waiting until I can
do the whole clutch or more likely sell the Jeep because I can't do my
own work anymore.
They put a new clutch in and left all the old crappy slave and throw out
in there???? If so, they/you got took.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
ctops wrote:
>
> I just got this Jeep I was told the clutch was just replaced , I can
> see the master cylinder is new , the fluid was dirty so I drained it
> out and replaced it I was told that Dot 3 brake fluid was fine by the
> NAPA guy, now my clutch works but makes a "rattling sound" when fully
> engaged , tried bleeding off the system , the 2 lines that come out of
> the Bell-housing are not secure must be a part missing that holds them
> the line with the bleeder valve can be pushed in and out , need
> schematic to see if part is missing, any help will be greatly
> appreciated
> Curt
cylinder which normally only comes as an expensive kit that includes the
master cylinder and costs about $800.00 to replace.... I did manage to
just find a master for my 88 so that is all I changed. I have the
rattle and now a leak in my slave cylinder. It is waiting until I can
do the whole clutch or more likely sell the Jeep because I can't do my
own work anymore.
They put a new clutch in and left all the old crappy slave and throw out
in there???? If so, they/you got took.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
ctops wrote:
>
> I just got this Jeep I was told the clutch was just replaced , I can
> see the master cylinder is new , the fluid was dirty so I drained it
> out and replaced it I was told that Dot 3 brake fluid was fine by the
> NAPA guy, now my clutch works but makes a "rattling sound" when fully
> engaged , tried bleeding off the system , the 2 lines that come out of
> the Bell-housing are not secure must be a part missing that holds them
> the line with the bleeder valve can be pushed in and out , need
> schematic to see if part is missing, any help will be greatly
> appreciated
> Curt
Guest
Posts: n/a
Re: 1988 Jeep Comanche clutch hydraulic fluid ?
The rattle is normally the throw out bearing which is part of the slave
cylinder which normally only comes as an expensive kit that includes the
master cylinder and costs about $800.00 to replace.... I did manage to
just find a master for my 88 so that is all I changed. I have the
rattle and now a leak in my slave cylinder. It is waiting until I can
do the whole clutch or more likely sell the Jeep because I can't do my
own work anymore.
They put a new clutch in and left all the old crappy slave and throw out
in there???? If so, they/you got took.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
ctops wrote:
>
> I just got this Jeep I was told the clutch was just replaced , I can
> see the master cylinder is new , the fluid was dirty so I drained it
> out and replaced it I was told that Dot 3 brake fluid was fine by the
> NAPA guy, now my clutch works but makes a "rattling sound" when fully
> engaged , tried bleeding off the system , the 2 lines that come out of
> the Bell-housing are not secure must be a part missing that holds them
> the line with the bleeder valve can be pushed in and out , need
> schematic to see if part is missing, any help will be greatly
> appreciated
> Curt
cylinder which normally only comes as an expensive kit that includes the
master cylinder and costs about $800.00 to replace.... I did manage to
just find a master for my 88 so that is all I changed. I have the
rattle and now a leak in my slave cylinder. It is waiting until I can
do the whole clutch or more likely sell the Jeep because I can't do my
own work anymore.
They put a new clutch in and left all the old crappy slave and throw out
in there???? If so, they/you got took.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
ctops wrote:
>
> I just got this Jeep I was told the clutch was just replaced , I can
> see the master cylinder is new , the fluid was dirty so I drained it
> out and replaced it I was told that Dot 3 brake fluid was fine by the
> NAPA guy, now my clutch works but makes a "rattling sound" when fully
> engaged , tried bleeding off the system , the 2 lines that come out of
> the Bell-housing are not secure must be a part missing that holds them
> the line with the bleeder valve can be pushed in and out , need
> schematic to see if part is missing, any help will be greatly
> appreciated
> Curt
Guest
Posts: n/a
Re: 1988 Jeep Comanche clutch hydraulic fluid ?
so, Mike.. Are you going to get better or worse over time? Sucky to see you
all messed up still.
KH
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:423704E4.38990F14@sympatico.ca...
> The rattle is normally the throw out bearing which is part of the slave
> cylinder which normally only comes as an expensive kit that includes the
> master cylinder and costs about $800.00 to replace.... I did manage to
> just find a master for my 88 so that is all I changed. I have the
> rattle and now a leak in my slave cylinder. It is waiting until I can
> do the whole clutch or more likely sell the Jeep because I can't do my
> own work anymore.
>
> They put a new clutch in and left all the old crappy slave and throw out
> in there???? If so, they/you got took.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> ctops wrote:
>>
>> I just got this Jeep I was told the clutch was just replaced , I can
>> see the master cylinder is new , the fluid was dirty so I drained it
>> out and replaced it I was told that Dot 3 brake fluid was fine by the
>> NAPA guy, now my clutch works but makes a "rattling sound" when fully
>> engaged , tried bleeding off the system , the 2 lines that come out of
>> the Bell-housing are not secure must be a part missing that holds them
>> the line with the bleeder valve can be pushed in and out , need
>> schematic to see if part is missing, any help will be greatly
>> appreciated
>> Curt
all messed up still.
KH
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:423704E4.38990F14@sympatico.ca...
> The rattle is normally the throw out bearing which is part of the slave
> cylinder which normally only comes as an expensive kit that includes the
> master cylinder and costs about $800.00 to replace.... I did manage to
> just find a master for my 88 so that is all I changed. I have the
> rattle and now a leak in my slave cylinder. It is waiting until I can
> do the whole clutch or more likely sell the Jeep because I can't do my
> own work anymore.
>
> They put a new clutch in and left all the old crappy slave and throw out
> in there???? If so, they/you got took.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> ctops wrote:
>>
>> I just got this Jeep I was told the clutch was just replaced , I can
>> see the master cylinder is new , the fluid was dirty so I drained it
>> out and replaced it I was told that Dot 3 brake fluid was fine by the
>> NAPA guy, now my clutch works but makes a "rattling sound" when fully
>> engaged , tried bleeding off the system , the 2 lines that come out of
>> the Bell-housing are not secure must be a part missing that holds them
>> the line with the bleeder valve can be pushed in and out , need
>> schematic to see if part is missing, any help will be greatly
>> appreciated
>> Curt
Guest
Posts: n/a
Re: 1988 Jeep Comanche clutch hydraulic fluid ?
so, Mike.. Are you going to get better or worse over time? Sucky to see you
all messed up still.
KH
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:423704E4.38990F14@sympatico.ca...
> The rattle is normally the throw out bearing which is part of the slave
> cylinder which normally only comes as an expensive kit that includes the
> master cylinder and costs about $800.00 to replace.... I did manage to
> just find a master for my 88 so that is all I changed. I have the
> rattle and now a leak in my slave cylinder. It is waiting until I can
> do the whole clutch or more likely sell the Jeep because I can't do my
> own work anymore.
>
> They put a new clutch in and left all the old crappy slave and throw out
> in there???? If so, they/you got took.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> ctops wrote:
>>
>> I just got this Jeep I was told the clutch was just replaced , I can
>> see the master cylinder is new , the fluid was dirty so I drained it
>> out and replaced it I was told that Dot 3 brake fluid was fine by the
>> NAPA guy, now my clutch works but makes a "rattling sound" when fully
>> engaged , tried bleeding off the system , the 2 lines that come out of
>> the Bell-housing are not secure must be a part missing that holds them
>> the line with the bleeder valve can be pushed in and out , need
>> schematic to see if part is missing, any help will be greatly
>> appreciated
>> Curt
all messed up still.
KH
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:423704E4.38990F14@sympatico.ca...
> The rattle is normally the throw out bearing which is part of the slave
> cylinder which normally only comes as an expensive kit that includes the
> master cylinder and costs about $800.00 to replace.... I did manage to
> just find a master for my 88 so that is all I changed. I have the
> rattle and now a leak in my slave cylinder. It is waiting until I can
> do the whole clutch or more likely sell the Jeep because I can't do my
> own work anymore.
>
> They put a new clutch in and left all the old crappy slave and throw out
> in there???? If so, they/you got took.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> ctops wrote:
>>
>> I just got this Jeep I was told the clutch was just replaced , I can
>> see the master cylinder is new , the fluid was dirty so I drained it
>> out and replaced it I was told that Dot 3 brake fluid was fine by the
>> NAPA guy, now my clutch works but makes a "rattling sound" when fully
>> engaged , tried bleeding off the system , the 2 lines that come out of
>> the Bell-housing are not secure must be a part missing that holds them
>> the line with the bleeder valve can be pushed in and out , need
>> schematic to see if part is missing, any help will be greatly
>> appreciated
>> Curt
Guest
Posts: n/a
Re: 1988 Jeep Comanche clutch hydraulic fluid ?
so, Mike.. Are you going to get better or worse over time? Sucky to see you
all messed up still.
KH
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:423704E4.38990F14@sympatico.ca...
> The rattle is normally the throw out bearing which is part of the slave
> cylinder which normally only comes as an expensive kit that includes the
> master cylinder and costs about $800.00 to replace.... I did manage to
> just find a master for my 88 so that is all I changed. I have the
> rattle and now a leak in my slave cylinder. It is waiting until I can
> do the whole clutch or more likely sell the Jeep because I can't do my
> own work anymore.
>
> They put a new clutch in and left all the old crappy slave and throw out
> in there???? If so, they/you got took.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> ctops wrote:
>>
>> I just got this Jeep I was told the clutch was just replaced , I can
>> see the master cylinder is new , the fluid was dirty so I drained it
>> out and replaced it I was told that Dot 3 brake fluid was fine by the
>> NAPA guy, now my clutch works but makes a "rattling sound" when fully
>> engaged , tried bleeding off the system , the 2 lines that come out of
>> the Bell-housing are not secure must be a part missing that holds them
>> the line with the bleeder valve can be pushed in and out , need
>> schematic to see if part is missing, any help will be greatly
>> appreciated
>> Curt
all messed up still.
KH
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:423704E4.38990F14@sympatico.ca...
> The rattle is normally the throw out bearing which is part of the slave
> cylinder which normally only comes as an expensive kit that includes the
> master cylinder and costs about $800.00 to replace.... I did manage to
> just find a master for my 88 so that is all I changed. I have the
> rattle and now a leak in my slave cylinder. It is waiting until I can
> do the whole clutch or more likely sell the Jeep because I can't do my
> own work anymore.
>
> They put a new clutch in and left all the old crappy slave and throw out
> in there???? If so, they/you got took.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> ctops wrote:
>>
>> I just got this Jeep I was told the clutch was just replaced , I can
>> see the master cylinder is new , the fluid was dirty so I drained it
>> out and replaced it I was told that Dot 3 brake fluid was fine by the
>> NAPA guy, now my clutch works but makes a "rattling sound" when fully
>> engaged , tried bleeding off the system , the 2 lines that come out of
>> the Bell-housing are not secure must be a part missing that holds them
>> the line with the bleeder valve can be pushed in and out , need
>> schematic to see if part is missing, any help will be greatly
>> appreciated
>> Curt
Guest
Posts: n/a
Re: 1988 Jeep Comanche clutch hydraulic fluid ?
Unfortunately not getting much better, just trying to learn to live with
it.
Mike
Kevin in San Diego wrote:
>
> so, Mike.. Are you going to get better or worse over time? Sucky to see you
> all messed up still.
> KH
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:423704E4.38990F14@sympatico.ca...
> > The rattle is normally the throw out bearing which is part of the slave
> > cylinder which normally only comes as an expensive kit that includes the
> > master cylinder and costs about $800.00 to replace.... I did manage to
> > just find a master for my 88 so that is all I changed. I have the
> > rattle and now a leak in my slave cylinder. It is waiting until I can
> > do the whole clutch or more likely sell the Jeep because I can't do my
> > own work anymore.
> >
> > They put a new clutch in and left all the old crappy slave and throw out
> > in there???? If so, they/you got took.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > ctops wrote:
> >>
> >> I just got this Jeep I was told the clutch was just replaced , I can
> >> see the master cylinder is new , the fluid was dirty so I drained it
> >> out and replaced it I was told that Dot 3 brake fluid was fine by the
> >> NAPA guy, now my clutch works but makes a "rattling sound" when fully
> >> engaged , tried bleeding off the system , the 2 lines that come out of
> >> the Bell-housing are not secure must be a part missing that holds them
> >> the line with the bleeder valve can be pushed in and out , need
> >> schematic to see if part is missing, any help will be greatly
> >> appreciated
> >> Curt
it.
Mike
Kevin in San Diego wrote:
>
> so, Mike.. Are you going to get better or worse over time? Sucky to see you
> all messed up still.
> KH
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:423704E4.38990F14@sympatico.ca...
> > The rattle is normally the throw out bearing which is part of the slave
> > cylinder which normally only comes as an expensive kit that includes the
> > master cylinder and costs about $800.00 to replace.... I did manage to
> > just find a master for my 88 so that is all I changed. I have the
> > rattle and now a leak in my slave cylinder. It is waiting until I can
> > do the whole clutch or more likely sell the Jeep because I can't do my
> > own work anymore.
> >
> > They put a new clutch in and left all the old crappy slave and throw out
> > in there???? If so, they/you got took.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > ctops wrote:
> >>
> >> I just got this Jeep I was told the clutch was just replaced , I can
> >> see the master cylinder is new , the fluid was dirty so I drained it
> >> out and replaced it I was told that Dot 3 brake fluid was fine by the
> >> NAPA guy, now my clutch works but makes a "rattling sound" when fully
> >> engaged , tried bleeding off the system , the 2 lines that come out of
> >> the Bell-housing are not secure must be a part missing that holds them
> >> the line with the bleeder valve can be pushed in and out , need
> >> schematic to see if part is missing, any help will be greatly
> >> appreciated
> >> Curt
Guest
Posts: n/a
Re: 1988 Jeep Comanche clutch hydraulic fluid ?
Unfortunately not getting much better, just trying to learn to live with
it.
Mike
Kevin in San Diego wrote:
>
> so, Mike.. Are you going to get better or worse over time? Sucky to see you
> all messed up still.
> KH
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:423704E4.38990F14@sympatico.ca...
> > The rattle is normally the throw out bearing which is part of the slave
> > cylinder which normally only comes as an expensive kit that includes the
> > master cylinder and costs about $800.00 to replace.... I did manage to
> > just find a master for my 88 so that is all I changed. I have the
> > rattle and now a leak in my slave cylinder. It is waiting until I can
> > do the whole clutch or more likely sell the Jeep because I can't do my
> > own work anymore.
> >
> > They put a new clutch in and left all the old crappy slave and throw out
> > in there???? If so, they/you got took.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > ctops wrote:
> >>
> >> I just got this Jeep I was told the clutch was just replaced , I can
> >> see the master cylinder is new , the fluid was dirty so I drained it
> >> out and replaced it I was told that Dot 3 brake fluid was fine by the
> >> NAPA guy, now my clutch works but makes a "rattling sound" when fully
> >> engaged , tried bleeding off the system , the 2 lines that come out of
> >> the Bell-housing are not secure must be a part missing that holds them
> >> the line with the bleeder valve can be pushed in and out , need
> >> schematic to see if part is missing, any help will be greatly
> >> appreciated
> >> Curt
it.
Mike
Kevin in San Diego wrote:
>
> so, Mike.. Are you going to get better or worse over time? Sucky to see you
> all messed up still.
> KH
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:423704E4.38990F14@sympatico.ca...
> > The rattle is normally the throw out bearing which is part of the slave
> > cylinder which normally only comes as an expensive kit that includes the
> > master cylinder and costs about $800.00 to replace.... I did manage to
> > just find a master for my 88 so that is all I changed. I have the
> > rattle and now a leak in my slave cylinder. It is waiting until I can
> > do the whole clutch or more likely sell the Jeep because I can't do my
> > own work anymore.
> >
> > They put a new clutch in and left all the old crappy slave and throw out
> > in there???? If so, they/you got took.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > ctops wrote:
> >>
> >> I just got this Jeep I was told the clutch was just replaced , I can
> >> see the master cylinder is new , the fluid was dirty so I drained it
> >> out and replaced it I was told that Dot 3 brake fluid was fine by the
> >> NAPA guy, now my clutch works but makes a "rattling sound" when fully
> >> engaged , tried bleeding off the system , the 2 lines that come out of
> >> the Bell-housing are not secure must be a part missing that holds them
> >> the line with the bleeder valve can be pushed in and out , need
> >> schematic to see if part is missing, any help will be greatly
> >> appreciated
> >> Curt
Guest
Posts: n/a
Re: 1988 Jeep Comanche clutch hydraulic fluid ?
Unfortunately not getting much better, just trying to learn to live with
it.
Mike
Kevin in San Diego wrote:
>
> so, Mike.. Are you going to get better or worse over time? Sucky to see you
> all messed up still.
> KH
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:423704E4.38990F14@sympatico.ca...
> > The rattle is normally the throw out bearing which is part of the slave
> > cylinder which normally only comes as an expensive kit that includes the
> > master cylinder and costs about $800.00 to replace.... I did manage to
> > just find a master for my 88 so that is all I changed. I have the
> > rattle and now a leak in my slave cylinder. It is waiting until I can
> > do the whole clutch or more likely sell the Jeep because I can't do my
> > own work anymore.
> >
> > They put a new clutch in and left all the old crappy slave and throw out
> > in there???? If so, they/you got took.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > ctops wrote:
> >>
> >> I just got this Jeep I was told the clutch was just replaced , I can
> >> see the master cylinder is new , the fluid was dirty so I drained it
> >> out and replaced it I was told that Dot 3 brake fluid was fine by the
> >> NAPA guy, now my clutch works but makes a "rattling sound" when fully
> >> engaged , tried bleeding off the system , the 2 lines that come out of
> >> the Bell-housing are not secure must be a part missing that holds them
> >> the line with the bleeder valve can be pushed in and out , need
> >> schematic to see if part is missing, any help will be greatly
> >> appreciated
> >> Curt
it.
Mike
Kevin in San Diego wrote:
>
> so, Mike.. Are you going to get better or worse over time? Sucky to see you
> all messed up still.
> KH
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:423704E4.38990F14@sympatico.ca...
> > The rattle is normally the throw out bearing which is part of the slave
> > cylinder which normally only comes as an expensive kit that includes the
> > master cylinder and costs about $800.00 to replace.... I did manage to
> > just find a master for my 88 so that is all I changed. I have the
> > rattle and now a leak in my slave cylinder. It is waiting until I can
> > do the whole clutch or more likely sell the Jeep because I can't do my
> > own work anymore.
> >
> > They put a new clutch in and left all the old crappy slave and throw out
> > in there???? If so, they/you got took.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > ctops wrote:
> >>
> >> I just got this Jeep I was told the clutch was just replaced , I can
> >> see the master cylinder is new , the fluid was dirty so I drained it
> >> out and replaced it I was told that Dot 3 brake fluid was fine by the
> >> NAPA guy, now my clutch works but makes a "rattling sound" when fully
> >> engaged , tried bleeding off the system , the 2 lines that come out of
> >> the Bell-housing are not secure must be a part missing that holds them
> >> the line with the bleeder valve can be pushed in and out , need
> >> schematic to see if part is missing, any help will be greatly
> >> appreciated
> >> Curt