Is it like a loud barking kind of noise, rather than a typical bearing
rattle sound? Any difference depending on if you're starting from a
stop, or going through a regular up/down shift while rolling?
what if you're hard on the throttle, vs, just nursing it.

if it's a loud barking noise and mostly when startiig from a stop, and
worse when you're harder on the throttle, could be oil contamination on
the disk.

Paul

ctops wrote:
> Mike it sounds like the Disk is gone of the pressure plate is coming
> apart or flywheel is cracked, when you push all the down on the clutch
> it's quiet, it's just when you get half way through the release that it
> raises HELL, my Jeep a good truck I just found out about a buddy of my
> that opened up his own garage, he will do the hold job for about
> $300.00 labor.
> parts and all lets see PP/Disk= $180.00 my Slave/ TO bearing = $105.00
> master $60.00, will need front Trans seal $12.00, got to have my ride
> go probation to do , just another bad thing about FL. everybody's in
> the system, thanks for the help.
> Curt
>

 

Is it like a loud barking kind of noise, rather than a typical bearing
rattle sound? Any difference depending on if you're starting from a
stop, or going through a regular up/down shift while rolling?
what if you're hard on the throttle, vs, just nursing it.

if it's a loud barking noise and mostly when startiig from a stop, and
worse when you're harder on the throttle, could be oil contamination on
the disk.

Paul

ctops wrote:
> Mike it sounds like the Disk is gone of the pressure plate is coming
> apart or flywheel is cracked, when you push all the down on the clutch
> it's quiet, it's just when you get half way through the release that it
> raises HELL, my Jeep a good truck I just found out about a buddy of my
> that opened up his own garage, he will do the hold job for about
> $300.00 labor.
> parts and all lets see PP/Disk= $180.00 my Slave/ TO bearing = $105.00
> master $60.00, will need front Trans seal $12.00, got to have my ride
> go probation to do , just another bad thing about FL. everybody's in
> the system, thanks for the help.
> Curt
>

 

Is it like a loud barking kind of noise, rather than a typical bearing
rattle sound? Any difference depending on if you're starting from a
stop, or going through a regular up/down shift while rolling?
what if you're hard on the throttle, vs, just nursing it.

if it's a loud barking noise and mostly when startiig from a stop, and
worse when you're harder on the throttle, could be oil contamination on
the disk.

Paul

ctops wrote:
> Mike it sounds like the Disk is gone of the pressure plate is coming
> apart or flywheel is cracked, when you push all the down on the clutch
> it's quiet, it's just when you get half way through the release that it
> raises HELL, my Jeep a good truck I just found out about a buddy of my
> that opened up his own garage, he will do the hold job for about
> $300.00 labor.
> parts and all lets see PP/Disk= $180.00 my Slave/ TO bearing = $105.00
> master $60.00, will need front Trans seal $12.00, got to have my ride
> go probation to do , just another bad thing about FL. everybody's in
> the system, thanks for the help.
> Curt
>

 

Well guys it's in the shop , will update after repair.

Curt

 

Well guys it's in the shop , will update after repair.

Curt

 

Well guys it's in the shop , will update after repair.

Curt

 

Well guy this is what happened, after everything was pulled the
pressure plate was new and so was the disk I had them checked , the
Slave looked new , the flywheel was just fine , so I had him just
install the new Slave I ha d already installed the new master , and
replaced the pilot bushing but it looked fine , , well that did it
clutch works fine , I guess what happened was that when I tried to
change the fluid it the system I ruined the seals in the Slave and it
would not work correctly, it can't be rebuilt , my mechanic said it
was a first for him , but I am finding out that jeeps are like that , I
have the old Slave if someone wants it, just pay the shipping.

Curtis

 

Well guy this is what happened, after everything was pulled the
pressure plate was new and so was the disk I had them checked , the
Slave looked new , the flywheel was just fine , so I had him just
install the new Slave I ha d already installed the new master , and
replaced the pilot bushing but it looked fine , , well that did it
clutch works fine , I guess what happened was that when I tried to
change the fluid it the system I ruined the seals in the Slave and it
would not work correctly, it can't be rebuilt , my mechanic said it
was a first for him , but I am finding out that jeeps are like that , I
have the old Slave if someone wants it, just pay the shipping.

Curtis

 

Well guy this is what happened, after everything was pulled the
pressure plate was new and so was the disk I had them checked , the
Slave looked new , the flywheel was just fine , so I had him just
install the new Slave I ha d already installed the new master , and
replaced the pilot bushing but it looked fine , , well that did it
clutch works fine , I guess what happened was that when I tried to
change the fluid it the system I ruined the seals in the Slave and it
would not work correctly, it can't be rebuilt , my mechanic said it
was a first for him , but I am finding out that jeeps are like that , I
have the old Slave if someone wants it, just pay the shipping.

Curtis

 

Well guy this is what happened, after everything was pulled the
pressure plate was new and so was the disk I had them checked , the
Slave looked new , the flywheel was just fine , so I had him just
install the new Slave I ha d already installed the new master , and
replaced the pilot bushing but it looked fine , , well that did it
clutch works fine , I guess what happened was that when I tried to
change the fluid it the system I ruined the seals in the Slave and it
would not work correctly, it can't be rebuilt , my mechanic said it
was a first for him , but I am finding out that jeeps are like that , I
have the old Slave if someone wants it, just pay the shipping.

Curtis