new key programming problems
Guest
Posts: n/a
Re: new key programming problems
I only got 1 key when I bought my WJ. I bought two blank transponder keys
on eBay and then had a local locksmith cut and program the first key with
their computer interface machine using the SKIM code I got from the Jeep
dealership PARTS department. The cutting and programming cost $24.99 and
the key blanks were $11.99 each.
I then programmed the second key myself after getting it cut by using the
directions on http://www.wjjeeps.com/sentry.htm#PROGRAM
I would recommend following the "Quick Steps" as the extra information in
the "Detailed Steps' initially led to some confusion.
Quick Steps:
A. Purchase a blank key and have it cut
B. Insert original key #1 into ignition and turn to On
C. Wait 5 seconds and turn key to off
D. Immediately insert original key # 2 into ignition and turn to on
E. Wait 10 seconds for SKIS indicator in dash starts to flash
F. Turn ignition off, insert new blank key and turn ignition back on
G. Once SKIS light stops flashing and turns off, your new key is programmed
"Seahag" <Seahag@toadymail.net> wrote in message
news:44bd7770_2@newsfeed.slurp.net...
> Seems to me I remember something about having to have 2 pre-programmed
> keys to make more. I only got one with my Jeep and the dealer charged $80
> (40 for parts and 40 for labor) for another one, which we proceeded to
> lose...
>
> Seahag
>
> "toxicated101" <matt.wheatley@gmail.com> wrote in message
> news:1153250560.400565.74140@b28g2000cwb.googlegro ups.com...
>> Hi
>>
>> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
>> had it cut at my local key cutting store. I have come to follow the
>> steps but the SKIS indicator light never turns on:
>>
>> B. Insert original key #1 into ignition and turn to On
>> C. Wait 5 seconds and turn key to off
>> D. Immediately insert original key # 2 into ignition and turn to on
>> E. Wait 10 seconds for SKIS indicator in dash starts to flash
>> F. Turn ignition off, insert new blank key and turn ignition back on
>> G. Once SKIS light stops flashing and turns off, your new key is
>> programmed
>>
>> Both keys I have will start the car, I have put key 1 into the ignition
>> and turned it it to on (by on I assume its the position that you drive
>> in rather than the start position) all the indicator light show up the
>> dash beeps 4 times all light go out, so 5 seconds after turning key is
>> about the time the beeps stop, turn the key to off (all lights go out)
>> put the second key in and turn to on, all lights go on, 5 beeps, lights
>> off, continue waiting but the SKIS indicator never starts to flash.
>>
>> Am I doing something wrong , should the jeep beep 4 times ( I assumed
>> that it is just checking gauges)
>>
>> Cheers
>>
>> Matt
>>
>
>
on eBay and then had a local locksmith cut and program the first key with
their computer interface machine using the SKIM code I got from the Jeep
dealership PARTS department. The cutting and programming cost $24.99 and
the key blanks were $11.99 each.
I then programmed the second key myself after getting it cut by using the
directions on http://www.wjjeeps.com/sentry.htm#PROGRAM
I would recommend following the "Quick Steps" as the extra information in
the "Detailed Steps' initially led to some confusion.
Quick Steps:
A. Purchase a blank key and have it cut
B. Insert original key #1 into ignition and turn to On
C. Wait 5 seconds and turn key to off
D. Immediately insert original key # 2 into ignition and turn to on
E. Wait 10 seconds for SKIS indicator in dash starts to flash
F. Turn ignition off, insert new blank key and turn ignition back on
G. Once SKIS light stops flashing and turns off, your new key is programmed
"Seahag" <Seahag@toadymail.net> wrote in message
news:44bd7770_2@newsfeed.slurp.net...
> Seems to me I remember something about having to have 2 pre-programmed
> keys to make more. I only got one with my Jeep and the dealer charged $80
> (40 for parts and 40 for labor) for another one, which we proceeded to
> lose...
>
> Seahag
>
> "toxicated101" <matt.wheatley@gmail.com> wrote in message
> news:1153250560.400565.74140@b28g2000cwb.googlegro ups.com...
>> Hi
>>
>> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
>> had it cut at my local key cutting store. I have come to follow the
>> steps but the SKIS indicator light never turns on:
>>
>> B. Insert original key #1 into ignition and turn to On
>> C. Wait 5 seconds and turn key to off
>> D. Immediately insert original key # 2 into ignition and turn to on
>> E. Wait 10 seconds for SKIS indicator in dash starts to flash
>> F. Turn ignition off, insert new blank key and turn ignition back on
>> G. Once SKIS light stops flashing and turns off, your new key is
>> programmed
>>
>> Both keys I have will start the car, I have put key 1 into the ignition
>> and turned it it to on (by on I assume its the position that you drive
>> in rather than the start position) all the indicator light show up the
>> dash beeps 4 times all light go out, so 5 seconds after turning key is
>> about the time the beeps stop, turn the key to off (all lights go out)
>> put the second key in and turn to on, all lights go on, 5 beeps, lights
>> off, continue waiting but the SKIS indicator never starts to flash.
>>
>> Am I doing something wrong , should the jeep beep 4 times ( I assumed
>> that it is just checking gauges)
>>
>> Cheers
>>
>> Matt
>>
>
>
Guest
Posts: n/a
Re: new key programming problems
I only got 1 key when I bought my WJ. I bought two blank transponder keys
on eBay and then had a local locksmith cut and program the first key with
their computer interface machine using the SKIM code I got from the Jeep
dealership PARTS department. The cutting and programming cost $24.99 and
the key blanks were $11.99 each.
I then programmed the second key myself after getting it cut by using the
directions on http://www.wjjeeps.com/sentry.htm#PROGRAM
I would recommend following the "Quick Steps" as the extra information in
the "Detailed Steps' initially led to some confusion.
Quick Steps:
A. Purchase a blank key and have it cut
B. Insert original key #1 into ignition and turn to On
C. Wait 5 seconds and turn key to off
D. Immediately insert original key # 2 into ignition and turn to on
E. Wait 10 seconds for SKIS indicator in dash starts to flash
F. Turn ignition off, insert new blank key and turn ignition back on
G. Once SKIS light stops flashing and turns off, your new key is programmed
"Seahag" <Seahag@toadymail.net> wrote in message
news:44bd7770_2@newsfeed.slurp.net...
> Seems to me I remember something about having to have 2 pre-programmed
> keys to make more. I only got one with my Jeep and the dealer charged $80
> (40 for parts and 40 for labor) for another one, which we proceeded to
> lose...
>
> Seahag
>
> "toxicated101" <matt.wheatley@gmail.com> wrote in message
> news:1153250560.400565.74140@b28g2000cwb.googlegro ups.com...
>> Hi
>>
>> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
>> had it cut at my local key cutting store. I have come to follow the
>> steps but the SKIS indicator light never turns on:
>>
>> B. Insert original key #1 into ignition and turn to On
>> C. Wait 5 seconds and turn key to off
>> D. Immediately insert original key # 2 into ignition and turn to on
>> E. Wait 10 seconds for SKIS indicator in dash starts to flash
>> F. Turn ignition off, insert new blank key and turn ignition back on
>> G. Once SKIS light stops flashing and turns off, your new key is
>> programmed
>>
>> Both keys I have will start the car, I have put key 1 into the ignition
>> and turned it it to on (by on I assume its the position that you drive
>> in rather than the start position) all the indicator light show up the
>> dash beeps 4 times all light go out, so 5 seconds after turning key is
>> about the time the beeps stop, turn the key to off (all lights go out)
>> put the second key in and turn to on, all lights go on, 5 beeps, lights
>> off, continue waiting but the SKIS indicator never starts to flash.
>>
>> Am I doing something wrong , should the jeep beep 4 times ( I assumed
>> that it is just checking gauges)
>>
>> Cheers
>>
>> Matt
>>
>
>
on eBay and then had a local locksmith cut and program the first key with
their computer interface machine using the SKIM code I got from the Jeep
dealership PARTS department. The cutting and programming cost $24.99 and
the key blanks were $11.99 each.
I then programmed the second key myself after getting it cut by using the
directions on http://www.wjjeeps.com/sentry.htm#PROGRAM
I would recommend following the "Quick Steps" as the extra information in
the "Detailed Steps' initially led to some confusion.
Quick Steps:
A. Purchase a blank key and have it cut
B. Insert original key #1 into ignition and turn to On
C. Wait 5 seconds and turn key to off
D. Immediately insert original key # 2 into ignition and turn to on
E. Wait 10 seconds for SKIS indicator in dash starts to flash
F. Turn ignition off, insert new blank key and turn ignition back on
G. Once SKIS light stops flashing and turns off, your new key is programmed
"Seahag" <Seahag@toadymail.net> wrote in message
news:44bd7770_2@newsfeed.slurp.net...
> Seems to me I remember something about having to have 2 pre-programmed
> keys to make more. I only got one with my Jeep and the dealer charged $80
> (40 for parts and 40 for labor) for another one, which we proceeded to
> lose...
>
> Seahag
>
> "toxicated101" <matt.wheatley@gmail.com> wrote in message
> news:1153250560.400565.74140@b28g2000cwb.googlegro ups.com...
>> Hi
>>
>> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
>> had it cut at my local key cutting store. I have come to follow the
>> steps but the SKIS indicator light never turns on:
>>
>> B. Insert original key #1 into ignition and turn to On
>> C. Wait 5 seconds and turn key to off
>> D. Immediately insert original key # 2 into ignition and turn to on
>> E. Wait 10 seconds for SKIS indicator in dash starts to flash
>> F. Turn ignition off, insert new blank key and turn ignition back on
>> G. Once SKIS light stops flashing and turns off, your new key is
>> programmed
>>
>> Both keys I have will start the car, I have put key 1 into the ignition
>> and turned it it to on (by on I assume its the position that you drive
>> in rather than the start position) all the indicator light show up the
>> dash beeps 4 times all light go out, so 5 seconds after turning key is
>> about the time the beeps stop, turn the key to off (all lights go out)
>> put the second key in and turn to on, all lights go on, 5 beeps, lights
>> off, continue waiting but the SKIS indicator never starts to flash.
>>
>> Am I doing something wrong , should the jeep beep 4 times ( I assumed
>> that it is just checking gauges)
>>
>> Cheers
>>
>> Matt
>>
>
>
Guest
Posts: n/a
Re: new key programming problems
I only got 1 key when I bought my WJ. I bought two blank transponder keys
on eBay and then had a local locksmith cut and program the first key with
their computer interface machine using the SKIM code I got from the Jeep
dealership PARTS department. The cutting and programming cost $24.99 and
the key blanks were $11.99 each.
I then programmed the second key myself after getting it cut by using the
directions on http://www.wjjeeps.com/sentry.htm#PROGRAM
I would recommend following the "Quick Steps" as the extra information in
the "Detailed Steps' initially led to some confusion.
Quick Steps:
A. Purchase a blank key and have it cut
B. Insert original key #1 into ignition and turn to On
C. Wait 5 seconds and turn key to off
D. Immediately insert original key # 2 into ignition and turn to on
E. Wait 10 seconds for SKIS indicator in dash starts to flash
F. Turn ignition off, insert new blank key and turn ignition back on
G. Once SKIS light stops flashing and turns off, your new key is programmed
The reason I got 2 keys made was so I would have a total of three, if I lost
one I would not have to pay another programming fee.
"Seahag" <Seahag@toadymail.net> wrote in message
news:44bd7770_2@newsfeed.slurp.net...
> Seems to me I remember something about having to have 2 pre-programmed
> keys to make more. I only got one with my Jeep and the dealer charged $80
> (40 for parts and 40 for labor) for another one, which we proceeded to
> lose...
>
> Seahag
>
> "toxicated101" <matt.wheatley@gmail.com> wrote in message
> news:1153250560.400565.74140@b28g2000cwb.googlegro ups.com...
>> Hi
>>
>> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
>> had it cut at my local key cutting store. I have come to follow the
>> steps but the SKIS indicator light never turns on:
>>
>> B. Insert original key #1 into ignition and turn to On
>> C. Wait 5 seconds and turn key to off
>> D. Immediately insert original key # 2 into ignition and turn to on
>> E. Wait 10 seconds for SKIS indicator in dash starts to flash
>> F. Turn ignition off, insert new blank key and turn ignition back on
>> G. Once SKIS light stops flashing and turns off, your new key is
>> programmed
>>
>> Both keys I have will start the car, I have put key 1 into the ignition
>> and turned it it to on (by on I assume its the position that you drive
>> in rather than the start position) all the indicator light show up the
>> dash beeps 4 times all light go out, so 5 seconds after turning key is
>> about the time the beeps stop, turn the key to off (all lights go out)
>> put the second key in and turn to on, all lights go on, 5 beeps, lights
>> off, continue waiting but the SKIS indicator never starts to flash.
>>
>> Am I doing something wrong , should the jeep beep 4 times ( I assumed
>> that it is just checking gauges)
>>
>> Cheers
>>
>> Matt
>>
>
>
on eBay and then had a local locksmith cut and program the first key with
their computer interface machine using the SKIM code I got from the Jeep
dealership PARTS department. The cutting and programming cost $24.99 and
the key blanks were $11.99 each.
I then programmed the second key myself after getting it cut by using the
directions on http://www.wjjeeps.com/sentry.htm#PROGRAM
I would recommend following the "Quick Steps" as the extra information in
the "Detailed Steps' initially led to some confusion.
Quick Steps:
A. Purchase a blank key and have it cut
B. Insert original key #1 into ignition and turn to On
C. Wait 5 seconds and turn key to off
D. Immediately insert original key # 2 into ignition and turn to on
E. Wait 10 seconds for SKIS indicator in dash starts to flash
F. Turn ignition off, insert new blank key and turn ignition back on
G. Once SKIS light stops flashing and turns off, your new key is programmed
The reason I got 2 keys made was so I would have a total of three, if I lost
one I would not have to pay another programming fee.
"Seahag" <Seahag@toadymail.net> wrote in message
news:44bd7770_2@newsfeed.slurp.net...
> Seems to me I remember something about having to have 2 pre-programmed
> keys to make more. I only got one with my Jeep and the dealer charged $80
> (40 for parts and 40 for labor) for another one, which we proceeded to
> lose...
>
> Seahag
>
> "toxicated101" <matt.wheatley@gmail.com> wrote in message
> news:1153250560.400565.74140@b28g2000cwb.googlegro ups.com...
>> Hi
>>
>> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
>> had it cut at my local key cutting store. I have come to follow the
>> steps but the SKIS indicator light never turns on:
>>
>> B. Insert original key #1 into ignition and turn to On
>> C. Wait 5 seconds and turn key to off
>> D. Immediately insert original key # 2 into ignition and turn to on
>> E. Wait 10 seconds for SKIS indicator in dash starts to flash
>> F. Turn ignition off, insert new blank key and turn ignition back on
>> G. Once SKIS light stops flashing and turns off, your new key is
>> programmed
>>
>> Both keys I have will start the car, I have put key 1 into the ignition
>> and turned it it to on (by on I assume its the position that you drive
>> in rather than the start position) all the indicator light show up the
>> dash beeps 4 times all light go out, so 5 seconds after turning key is
>> about the time the beeps stop, turn the key to off (all lights go out)
>> put the second key in and turn to on, all lights go on, 5 beeps, lights
>> off, continue waiting but the SKIS indicator never starts to flash.
>>
>> Am I doing something wrong , should the jeep beep 4 times ( I assumed
>> that it is just checking gauges)
>>
>> Cheers
>>
>> Matt
>>
>
>
Guest
Posts: n/a
Re: new key programming problems
I only got 1 key when I bought my WJ. I bought two blank transponder keys
on eBay and then had a local locksmith cut and program the first key with
their computer interface machine using the SKIM code I got from the Jeep
dealership PARTS department. The cutting and programming cost $24.99 and
the key blanks were $11.99 each.
I then programmed the second key myself after getting it cut by using the
directions on http://www.wjjeeps.com/sentry.htm#PROGRAM
I would recommend following the "Quick Steps" as the extra information in
the "Detailed Steps' initially led to some confusion.
Quick Steps:
A. Purchase a blank key and have it cut
B. Insert original key #1 into ignition and turn to On
C. Wait 5 seconds and turn key to off
D. Immediately insert original key # 2 into ignition and turn to on
E. Wait 10 seconds for SKIS indicator in dash starts to flash
F. Turn ignition off, insert new blank key and turn ignition back on
G. Once SKIS light stops flashing and turns off, your new key is programmed
The reason I got 2 keys made was so I would have a total of three, if I lost
one I would not have to pay another programming fee.
"Seahag" <Seahag@toadymail.net> wrote in message
news:44bd7770_2@newsfeed.slurp.net...
> Seems to me I remember something about having to have 2 pre-programmed
> keys to make more. I only got one with my Jeep and the dealer charged $80
> (40 for parts and 40 for labor) for another one, which we proceeded to
> lose...
>
> Seahag
>
> "toxicated101" <matt.wheatley@gmail.com> wrote in message
> news:1153250560.400565.74140@b28g2000cwb.googlegro ups.com...
>> Hi
>>
>> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
>> had it cut at my local key cutting store. I have come to follow the
>> steps but the SKIS indicator light never turns on:
>>
>> B. Insert original key #1 into ignition and turn to On
>> C. Wait 5 seconds and turn key to off
>> D. Immediately insert original key # 2 into ignition and turn to on
>> E. Wait 10 seconds for SKIS indicator in dash starts to flash
>> F. Turn ignition off, insert new blank key and turn ignition back on
>> G. Once SKIS light stops flashing and turns off, your new key is
>> programmed
>>
>> Both keys I have will start the car, I have put key 1 into the ignition
>> and turned it it to on (by on I assume its the position that you drive
>> in rather than the start position) all the indicator light show up the
>> dash beeps 4 times all light go out, so 5 seconds after turning key is
>> about the time the beeps stop, turn the key to off (all lights go out)
>> put the second key in and turn to on, all lights go on, 5 beeps, lights
>> off, continue waiting but the SKIS indicator never starts to flash.
>>
>> Am I doing something wrong , should the jeep beep 4 times ( I assumed
>> that it is just checking gauges)
>>
>> Cheers
>>
>> Matt
>>
>
>
on eBay and then had a local locksmith cut and program the first key with
their computer interface machine using the SKIM code I got from the Jeep
dealership PARTS department. The cutting and programming cost $24.99 and
the key blanks were $11.99 each.
I then programmed the second key myself after getting it cut by using the
directions on http://www.wjjeeps.com/sentry.htm#PROGRAM
I would recommend following the "Quick Steps" as the extra information in
the "Detailed Steps' initially led to some confusion.
Quick Steps:
A. Purchase a blank key and have it cut
B. Insert original key #1 into ignition and turn to On
C. Wait 5 seconds and turn key to off
D. Immediately insert original key # 2 into ignition and turn to on
E. Wait 10 seconds for SKIS indicator in dash starts to flash
F. Turn ignition off, insert new blank key and turn ignition back on
G. Once SKIS light stops flashing and turns off, your new key is programmed
The reason I got 2 keys made was so I would have a total of three, if I lost
one I would not have to pay another programming fee.
"Seahag" <Seahag@toadymail.net> wrote in message
news:44bd7770_2@newsfeed.slurp.net...
> Seems to me I remember something about having to have 2 pre-programmed
> keys to make more. I only got one with my Jeep and the dealer charged $80
> (40 for parts and 40 for labor) for another one, which we proceeded to
> lose...
>
> Seahag
>
> "toxicated101" <matt.wheatley@gmail.com> wrote in message
> news:1153250560.400565.74140@b28g2000cwb.googlegro ups.com...
>> Hi
>>
>> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
>> had it cut at my local key cutting store. I have come to follow the
>> steps but the SKIS indicator light never turns on:
>>
>> B. Insert original key #1 into ignition and turn to On
>> C. Wait 5 seconds and turn key to off
>> D. Immediately insert original key # 2 into ignition and turn to on
>> E. Wait 10 seconds for SKIS indicator in dash starts to flash
>> F. Turn ignition off, insert new blank key and turn ignition back on
>> G. Once SKIS light stops flashing and turns off, your new key is
>> programmed
>>
>> Both keys I have will start the car, I have put key 1 into the ignition
>> and turned it it to on (by on I assume its the position that you drive
>> in rather than the start position) all the indicator light show up the
>> dash beeps 4 times all light go out, so 5 seconds after turning key is
>> about the time the beeps stop, turn the key to off (all lights go out)
>> put the second key in and turn to on, all lights go on, 5 beeps, lights
>> off, continue waiting but the SKIS indicator never starts to flash.
>>
>> Am I doing something wrong , should the jeep beep 4 times ( I assumed
>> that it is just checking gauges)
>>
>> Cheers
>>
>> Matt
>>
>
>
Guest
Posts: n/a
Re: new key programming problems
I only got 1 key when I bought my WJ. I bought two blank transponder keys
on eBay and then had a local locksmith cut and program the first key with
their computer interface machine using the SKIM code I got from the Jeep
dealership PARTS department. The cutting and programming cost $24.99 and
the key blanks were $11.99 each.
I then programmed the second key myself after getting it cut by using the
directions on http://www.wjjeeps.com/sentry.htm#PROGRAM
I would recommend following the "Quick Steps" as the extra information in
the "Detailed Steps' initially led to some confusion.
Quick Steps:
A. Purchase a blank key and have it cut
B. Insert original key #1 into ignition and turn to On
C. Wait 5 seconds and turn key to off
D. Immediately insert original key # 2 into ignition and turn to on
E. Wait 10 seconds for SKIS indicator in dash starts to flash
F. Turn ignition off, insert new blank key and turn ignition back on
G. Once SKIS light stops flashing and turns off, your new key is programmed
The reason I got 2 keys made was so I would have a total of three, if I lost
one I would not have to pay another programming fee.
"Seahag" <Seahag@toadymail.net> wrote in message
news:44bd7770_2@newsfeed.slurp.net...
> Seems to me I remember something about having to have 2 pre-programmed
> keys to make more. I only got one with my Jeep and the dealer charged $80
> (40 for parts and 40 for labor) for another one, which we proceeded to
> lose...
>
> Seahag
>
> "toxicated101" <matt.wheatley@gmail.com> wrote in message
> news:1153250560.400565.74140@b28g2000cwb.googlegro ups.com...
>> Hi
>>
>> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
>> had it cut at my local key cutting store. I have come to follow the
>> steps but the SKIS indicator light never turns on:
>>
>> B. Insert original key #1 into ignition and turn to On
>> C. Wait 5 seconds and turn key to off
>> D. Immediately insert original key # 2 into ignition and turn to on
>> E. Wait 10 seconds for SKIS indicator in dash starts to flash
>> F. Turn ignition off, insert new blank key and turn ignition back on
>> G. Once SKIS light stops flashing and turns off, your new key is
>> programmed
>>
>> Both keys I have will start the car, I have put key 1 into the ignition
>> and turned it it to on (by on I assume its the position that you drive
>> in rather than the start position) all the indicator light show up the
>> dash beeps 4 times all light go out, so 5 seconds after turning key is
>> about the time the beeps stop, turn the key to off (all lights go out)
>> put the second key in and turn to on, all lights go on, 5 beeps, lights
>> off, continue waiting but the SKIS indicator never starts to flash.
>>
>> Am I doing something wrong , should the jeep beep 4 times ( I assumed
>> that it is just checking gauges)
>>
>> Cheers
>>
>> Matt
>>
>
>
on eBay and then had a local locksmith cut and program the first key with
their computer interface machine using the SKIM code I got from the Jeep
dealership PARTS department. The cutting and programming cost $24.99 and
the key blanks were $11.99 each.
I then programmed the second key myself after getting it cut by using the
directions on http://www.wjjeeps.com/sentry.htm#PROGRAM
I would recommend following the "Quick Steps" as the extra information in
the "Detailed Steps' initially led to some confusion.
Quick Steps:
A. Purchase a blank key and have it cut
B. Insert original key #1 into ignition and turn to On
C. Wait 5 seconds and turn key to off
D. Immediately insert original key # 2 into ignition and turn to on
E. Wait 10 seconds for SKIS indicator in dash starts to flash
F. Turn ignition off, insert new blank key and turn ignition back on
G. Once SKIS light stops flashing and turns off, your new key is programmed
The reason I got 2 keys made was so I would have a total of three, if I lost
one I would not have to pay another programming fee.
"Seahag" <Seahag@toadymail.net> wrote in message
news:44bd7770_2@newsfeed.slurp.net...
> Seems to me I remember something about having to have 2 pre-programmed
> keys to make more. I only got one with my Jeep and the dealer charged $80
> (40 for parts and 40 for labor) for another one, which we proceeded to
> lose...
>
> Seahag
>
> "toxicated101" <matt.wheatley@gmail.com> wrote in message
> news:1153250560.400565.74140@b28g2000cwb.googlegro ups.com...
>> Hi
>>
>> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
>> had it cut at my local key cutting store. I have come to follow the
>> steps but the SKIS indicator light never turns on:
>>
>> B. Insert original key #1 into ignition and turn to On
>> C. Wait 5 seconds and turn key to off
>> D. Immediately insert original key # 2 into ignition and turn to on
>> E. Wait 10 seconds for SKIS indicator in dash starts to flash
>> F. Turn ignition off, insert new blank key and turn ignition back on
>> G. Once SKIS light stops flashing and turns off, your new key is
>> programmed
>>
>> Both keys I have will start the car, I have put key 1 into the ignition
>> and turned it it to on (by on I assume its the position that you drive
>> in rather than the start position) all the indicator light show up the
>> dash beeps 4 times all light go out, so 5 seconds after turning key is
>> about the time the beeps stop, turn the key to off (all lights go out)
>> put the second key in and turn to on, all lights go on, 5 beeps, lights
>> off, continue waiting but the SKIS indicator never starts to flash.
>>
>> Am I doing something wrong , should the jeep beep 4 times ( I assumed
>> that it is just checking gauges)
>>
>> Cheers
>>
>> Matt
>>
>
>
Guest
Posts: n/a
Re: new key programming problems
Hi
Maybe I didn't make my self clear, I got the jeep with 2 keys both work
and start the car, I have now purchased a 3rd key had it cut and it is
this key I am having problems programming.
Key A (Original Key starts car)
Key B (Original/spare Key starts car)
Key C (New Key has been cut, needs programming)
I insert Key A and turn to on, wait between 3 and 15 seconds, turn to
off.
I then insert Key B and turn to on (withing 15 seconds) and wait, but
no SKIS light comes on.
I assume the SKIS light is the one of the picture of the key with the
line going through it. Which works because it comes on during the
initial lamp test, you know when you turn the key to on and all the
lights light up, then go out after a few seconds.
I have followed the instructions , they don't seam so complicated,
insert one key turn to on wait 5 seconds, turn off, insert key 2 , turn
to on wait 10 seconds light and a beep should be heard , insert new
key, but no light or beep.
Is there something I'm missing?
Cheers
Matt
billy ray wrote:
> I only got 1 key when I bought my WJ. I bought two blank transponder keys
> on eBay and then had a local locksmith cut and program the first key with
> their computer interface machine using the SKIM code I got from the Jeep
> dealership PARTS department. The cutting and programming cost $24.99 and
> the key blanks were $11.99 each.
>
> I then programmed the second key myself after getting it cut by using the
> directions on http://www.wjjeeps.com/sentry.htm#PROGRAM
>
> I would recommend following the "Quick Steps" as the extra information in
> the "Detailed Steps' initially led to some confusion.
> Quick Steps:
>
> A. Purchase a blank key and have it cut
> B. Insert original key #1 into ignition and turn to On
> C. Wait 5 seconds and turn key to off
> D. Immediately insert original key # 2 into ignition and turn to on
> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> F. Turn ignition off, insert new blank key and turn ignition back on
> G. Once SKIS light stops flashing and turns off, your new key is programmed
>
> The reason I got 2 keys made was so I would have a total of three, if I lost
> one I would not have to pay another programming fee.
>
>
>
>
> "Seahag" <Seahag@toadymail.net> wrote in message
> news:44bd7770_2@newsfeed.slurp.net...
> > Seems to me I remember something about having to have 2 pre-programmed
> > keys to make more. I only got one with my Jeep and the dealer charged $80
> > (40 for parts and 40 for labor) for another one, which we proceeded to
> > lose...
> >
> > Seahag
> >
> > "toxicated101" <matt.wheatley@gmail.com> wrote in message
> > news:1153250560.400565.74140@b28g2000cwb.googlegro ups.com...
> >> Hi
> >>
> >> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
> >> had it cut at my local key cutting store. I have come to follow the
> >> steps but the SKIS indicator light never turns on:
> >>
> >> B. Insert original key #1 into ignition and turn to On
> >> C. Wait 5 seconds and turn key to off
> >> D. Immediately insert original key # 2 into ignition and turn to on
> >> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> >> F. Turn ignition off, insert new blank key and turn ignition back on
> >> G. Once SKIS light stops flashing and turns off, your new key is
> >> programmed
> >>
> >> Both keys I have will start the car, I have put key 1 into the ignition
> >> and turned it it to on (by on I assume its the position that you drive
> >> in rather than the start position) all the indicator light show up the
> >> dash beeps 4 times all light go out, so 5 seconds after turning key is
> >> about the time the beeps stop, turn the key to off (all lights go out)
> >> put the second key in and turn to on, all lights go on, 5 beeps, lights
> >> off, continue waiting but the SKIS indicator never starts to flash.
> >>
> >> Am I doing something wrong , should the jeep beep 4 times ( I assumed
> >> that it is just checking gauges)
> >>
> >> Cheers
> >>
> >> Matt
> >>
> >
> >
Maybe I didn't make my self clear, I got the jeep with 2 keys both work
and start the car, I have now purchased a 3rd key had it cut and it is
this key I am having problems programming.
Key A (Original Key starts car)
Key B (Original/spare Key starts car)
Key C (New Key has been cut, needs programming)
I insert Key A and turn to on, wait between 3 and 15 seconds, turn to
off.
I then insert Key B and turn to on (withing 15 seconds) and wait, but
no SKIS light comes on.
I assume the SKIS light is the one of the picture of the key with the
line going through it. Which works because it comes on during the
initial lamp test, you know when you turn the key to on and all the
lights light up, then go out after a few seconds.
I have followed the instructions , they don't seam so complicated,
insert one key turn to on wait 5 seconds, turn off, insert key 2 , turn
to on wait 10 seconds light and a beep should be heard , insert new
key, but no light or beep.
Is there something I'm missing?
Cheers
Matt
billy ray wrote:
> I only got 1 key when I bought my WJ. I bought two blank transponder keys
> on eBay and then had a local locksmith cut and program the first key with
> their computer interface machine using the SKIM code I got from the Jeep
> dealership PARTS department. The cutting and programming cost $24.99 and
> the key blanks were $11.99 each.
>
> I then programmed the second key myself after getting it cut by using the
> directions on http://www.wjjeeps.com/sentry.htm#PROGRAM
>
> I would recommend following the "Quick Steps" as the extra information in
> the "Detailed Steps' initially led to some confusion.
> Quick Steps:
>
> A. Purchase a blank key and have it cut
> B. Insert original key #1 into ignition and turn to On
> C. Wait 5 seconds and turn key to off
> D. Immediately insert original key # 2 into ignition and turn to on
> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> F. Turn ignition off, insert new blank key and turn ignition back on
> G. Once SKIS light stops flashing and turns off, your new key is programmed
>
> The reason I got 2 keys made was so I would have a total of three, if I lost
> one I would not have to pay another programming fee.
>
>
>
>
> "Seahag" <Seahag@toadymail.net> wrote in message
> news:44bd7770_2@newsfeed.slurp.net...
> > Seems to me I remember something about having to have 2 pre-programmed
> > keys to make more. I only got one with my Jeep and the dealer charged $80
> > (40 for parts and 40 for labor) for another one, which we proceeded to
> > lose...
> >
> > Seahag
> >
> > "toxicated101" <matt.wheatley@gmail.com> wrote in message
> > news:1153250560.400565.74140@b28g2000cwb.googlegro ups.com...
> >> Hi
> >>
> >> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
> >> had it cut at my local key cutting store. I have come to follow the
> >> steps but the SKIS indicator light never turns on:
> >>
> >> B. Insert original key #1 into ignition and turn to On
> >> C. Wait 5 seconds and turn key to off
> >> D. Immediately insert original key # 2 into ignition and turn to on
> >> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> >> F. Turn ignition off, insert new blank key and turn ignition back on
> >> G. Once SKIS light stops flashing and turns off, your new key is
> >> programmed
> >>
> >> Both keys I have will start the car, I have put key 1 into the ignition
> >> and turned it it to on (by on I assume its the position that you drive
> >> in rather than the start position) all the indicator light show up the
> >> dash beeps 4 times all light go out, so 5 seconds after turning key is
> >> about the time the beeps stop, turn the key to off (all lights go out)
> >> put the second key in and turn to on, all lights go on, 5 beeps, lights
> >> off, continue waiting but the SKIS indicator never starts to flash.
> >>
> >> Am I doing something wrong , should the jeep beep 4 times ( I assumed
> >> that it is just checking gauges)
> >>
> >> Cheers
> >>
> >> Matt
> >>
> >
> >
Guest
Posts: n/a
Re: new key programming problems
Hi
Maybe I didn't make my self clear, I got the jeep with 2 keys both work
and start the car, I have now purchased a 3rd key had it cut and it is
this key I am having problems programming.
Key A (Original Key starts car)
Key B (Original/spare Key starts car)
Key C (New Key has been cut, needs programming)
I insert Key A and turn to on, wait between 3 and 15 seconds, turn to
off.
I then insert Key B and turn to on (withing 15 seconds) and wait, but
no SKIS light comes on.
I assume the SKIS light is the one of the picture of the key with the
line going through it. Which works because it comes on during the
initial lamp test, you know when you turn the key to on and all the
lights light up, then go out after a few seconds.
I have followed the instructions , they don't seam so complicated,
insert one key turn to on wait 5 seconds, turn off, insert key 2 , turn
to on wait 10 seconds light and a beep should be heard , insert new
key, but no light or beep.
Is there something I'm missing?
Cheers
Matt
billy ray wrote:
> I only got 1 key when I bought my WJ. I bought two blank transponder keys
> on eBay and then had a local locksmith cut and program the first key with
> their computer interface machine using the SKIM code I got from the Jeep
> dealership PARTS department. The cutting and programming cost $24.99 and
> the key blanks were $11.99 each.
>
> I then programmed the second key myself after getting it cut by using the
> directions on http://www.wjjeeps.com/sentry.htm#PROGRAM
>
> I would recommend following the "Quick Steps" as the extra information in
> the "Detailed Steps' initially led to some confusion.
> Quick Steps:
>
> A. Purchase a blank key and have it cut
> B. Insert original key #1 into ignition and turn to On
> C. Wait 5 seconds and turn key to off
> D. Immediately insert original key # 2 into ignition and turn to on
> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> F. Turn ignition off, insert new blank key and turn ignition back on
> G. Once SKIS light stops flashing and turns off, your new key is programmed
>
> The reason I got 2 keys made was so I would have a total of three, if I lost
> one I would not have to pay another programming fee.
>
>
>
>
> "Seahag" <Seahag@toadymail.net> wrote in message
> news:44bd7770_2@newsfeed.slurp.net...
> > Seems to me I remember something about having to have 2 pre-programmed
> > keys to make more. I only got one with my Jeep and the dealer charged $80
> > (40 for parts and 40 for labor) for another one, which we proceeded to
> > lose...
> >
> > Seahag
> >
> > "toxicated101" <matt.wheatley@gmail.com> wrote in message
> > news:1153250560.400565.74140@b28g2000cwb.googlegro ups.com...
> >> Hi
> >>
> >> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
> >> had it cut at my local key cutting store. I have come to follow the
> >> steps but the SKIS indicator light never turns on:
> >>
> >> B. Insert original key #1 into ignition and turn to On
> >> C. Wait 5 seconds and turn key to off
> >> D. Immediately insert original key # 2 into ignition and turn to on
> >> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> >> F. Turn ignition off, insert new blank key and turn ignition back on
> >> G. Once SKIS light stops flashing and turns off, your new key is
> >> programmed
> >>
> >> Both keys I have will start the car, I have put key 1 into the ignition
> >> and turned it it to on (by on I assume its the position that you drive
> >> in rather than the start position) all the indicator light show up the
> >> dash beeps 4 times all light go out, so 5 seconds after turning key is
> >> about the time the beeps stop, turn the key to off (all lights go out)
> >> put the second key in and turn to on, all lights go on, 5 beeps, lights
> >> off, continue waiting but the SKIS indicator never starts to flash.
> >>
> >> Am I doing something wrong , should the jeep beep 4 times ( I assumed
> >> that it is just checking gauges)
> >>
> >> Cheers
> >>
> >> Matt
> >>
> >
> >
Maybe I didn't make my self clear, I got the jeep with 2 keys both work
and start the car, I have now purchased a 3rd key had it cut and it is
this key I am having problems programming.
Key A (Original Key starts car)
Key B (Original/spare Key starts car)
Key C (New Key has been cut, needs programming)
I insert Key A and turn to on, wait between 3 and 15 seconds, turn to
off.
I then insert Key B and turn to on (withing 15 seconds) and wait, but
no SKIS light comes on.
I assume the SKIS light is the one of the picture of the key with the
line going through it. Which works because it comes on during the
initial lamp test, you know when you turn the key to on and all the
lights light up, then go out after a few seconds.
I have followed the instructions , they don't seam so complicated,
insert one key turn to on wait 5 seconds, turn off, insert key 2 , turn
to on wait 10 seconds light and a beep should be heard , insert new
key, but no light or beep.
Is there something I'm missing?
Cheers
Matt
billy ray wrote:
> I only got 1 key when I bought my WJ. I bought two blank transponder keys
> on eBay and then had a local locksmith cut and program the first key with
> their computer interface machine using the SKIM code I got from the Jeep
> dealership PARTS department. The cutting and programming cost $24.99 and
> the key blanks were $11.99 each.
>
> I then programmed the second key myself after getting it cut by using the
> directions on http://www.wjjeeps.com/sentry.htm#PROGRAM
>
> I would recommend following the "Quick Steps" as the extra information in
> the "Detailed Steps' initially led to some confusion.
> Quick Steps:
>
> A. Purchase a blank key and have it cut
> B. Insert original key #1 into ignition and turn to On
> C. Wait 5 seconds and turn key to off
> D. Immediately insert original key # 2 into ignition and turn to on
> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> F. Turn ignition off, insert new blank key and turn ignition back on
> G. Once SKIS light stops flashing and turns off, your new key is programmed
>
> The reason I got 2 keys made was so I would have a total of three, if I lost
> one I would not have to pay another programming fee.
>
>
>
>
> "Seahag" <Seahag@toadymail.net> wrote in message
> news:44bd7770_2@newsfeed.slurp.net...
> > Seems to me I remember something about having to have 2 pre-programmed
> > keys to make more. I only got one with my Jeep and the dealer charged $80
> > (40 for parts and 40 for labor) for another one, which we proceeded to
> > lose...
> >
> > Seahag
> >
> > "toxicated101" <matt.wheatley@gmail.com> wrote in message
> > news:1153250560.400565.74140@b28g2000cwb.googlegro ups.com...
> >> Hi
> >>
> >> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
> >> had it cut at my local key cutting store. I have come to follow the
> >> steps but the SKIS indicator light never turns on:
> >>
> >> B. Insert original key #1 into ignition and turn to On
> >> C. Wait 5 seconds and turn key to off
> >> D. Immediately insert original key # 2 into ignition and turn to on
> >> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> >> F. Turn ignition off, insert new blank key and turn ignition back on
> >> G. Once SKIS light stops flashing and turns off, your new key is
> >> programmed
> >>
> >> Both keys I have will start the car, I have put key 1 into the ignition
> >> and turned it it to on (by on I assume its the position that you drive
> >> in rather than the start position) all the indicator light show up the
> >> dash beeps 4 times all light go out, so 5 seconds after turning key is
> >> about the time the beeps stop, turn the key to off (all lights go out)
> >> put the second key in and turn to on, all lights go on, 5 beeps, lights
> >> off, continue waiting but the SKIS indicator never starts to flash.
> >>
> >> Am I doing something wrong , should the jeep beep 4 times ( I assumed
> >> that it is just checking gauges)
> >>
> >> Cheers
> >>
> >> Matt
> >>
> >
> >
Guest
Posts: n/a
Re: new key programming problems
Hi
Maybe I didn't make my self clear, I got the jeep with 2 keys both work
and start the car, I have now purchased a 3rd key had it cut and it is
this key I am having problems programming.
Key A (Original Key starts car)
Key B (Original/spare Key starts car)
Key C (New Key has been cut, needs programming)
I insert Key A and turn to on, wait between 3 and 15 seconds, turn to
off.
I then insert Key B and turn to on (withing 15 seconds) and wait, but
no SKIS light comes on.
I assume the SKIS light is the one of the picture of the key with the
line going through it. Which works because it comes on during the
initial lamp test, you know when you turn the key to on and all the
lights light up, then go out after a few seconds.
I have followed the instructions , they don't seam so complicated,
insert one key turn to on wait 5 seconds, turn off, insert key 2 , turn
to on wait 10 seconds light and a beep should be heard , insert new
key, but no light or beep.
Is there something I'm missing?
Cheers
Matt
billy ray wrote:
> I only got 1 key when I bought my WJ. I bought two blank transponder keys
> on eBay and then had a local locksmith cut and program the first key with
> their computer interface machine using the SKIM code I got from the Jeep
> dealership PARTS department. The cutting and programming cost $24.99 and
> the key blanks were $11.99 each.
>
> I then programmed the second key myself after getting it cut by using the
> directions on http://www.wjjeeps.com/sentry.htm#PROGRAM
>
> I would recommend following the "Quick Steps" as the extra information in
> the "Detailed Steps' initially led to some confusion.
> Quick Steps:
>
> A. Purchase a blank key and have it cut
> B. Insert original key #1 into ignition and turn to On
> C. Wait 5 seconds and turn key to off
> D. Immediately insert original key # 2 into ignition and turn to on
> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> F. Turn ignition off, insert new blank key and turn ignition back on
> G. Once SKIS light stops flashing and turns off, your new key is programmed
>
> The reason I got 2 keys made was so I would have a total of three, if I lost
> one I would not have to pay another programming fee.
>
>
>
>
> "Seahag" <Seahag@toadymail.net> wrote in message
> news:44bd7770_2@newsfeed.slurp.net...
> > Seems to me I remember something about having to have 2 pre-programmed
> > keys to make more. I only got one with my Jeep and the dealer charged $80
> > (40 for parts and 40 for labor) for another one, which we proceeded to
> > lose...
> >
> > Seahag
> >
> > "toxicated101" <matt.wheatley@gmail.com> wrote in message
> > news:1153250560.400565.74140@b28g2000cwb.googlegro ups.com...
> >> Hi
> >>
> >> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
> >> had it cut at my local key cutting store. I have come to follow the
> >> steps but the SKIS indicator light never turns on:
> >>
> >> B. Insert original key #1 into ignition and turn to On
> >> C. Wait 5 seconds and turn key to off
> >> D. Immediately insert original key # 2 into ignition and turn to on
> >> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> >> F. Turn ignition off, insert new blank key and turn ignition back on
> >> G. Once SKIS light stops flashing and turns off, your new key is
> >> programmed
> >>
> >> Both keys I have will start the car, I have put key 1 into the ignition
> >> and turned it it to on (by on I assume its the position that you drive
> >> in rather than the start position) all the indicator light show up the
> >> dash beeps 4 times all light go out, so 5 seconds after turning key is
> >> about the time the beeps stop, turn the key to off (all lights go out)
> >> put the second key in and turn to on, all lights go on, 5 beeps, lights
> >> off, continue waiting but the SKIS indicator never starts to flash.
> >>
> >> Am I doing something wrong , should the jeep beep 4 times ( I assumed
> >> that it is just checking gauges)
> >>
> >> Cheers
> >>
> >> Matt
> >>
> >
> >
Maybe I didn't make my self clear, I got the jeep with 2 keys both work
and start the car, I have now purchased a 3rd key had it cut and it is
this key I am having problems programming.
Key A (Original Key starts car)
Key B (Original/spare Key starts car)
Key C (New Key has been cut, needs programming)
I insert Key A and turn to on, wait between 3 and 15 seconds, turn to
off.
I then insert Key B and turn to on (withing 15 seconds) and wait, but
no SKIS light comes on.
I assume the SKIS light is the one of the picture of the key with the
line going through it. Which works because it comes on during the
initial lamp test, you know when you turn the key to on and all the
lights light up, then go out after a few seconds.
I have followed the instructions , they don't seam so complicated,
insert one key turn to on wait 5 seconds, turn off, insert key 2 , turn
to on wait 10 seconds light and a beep should be heard , insert new
key, but no light or beep.
Is there something I'm missing?
Cheers
Matt
billy ray wrote:
> I only got 1 key when I bought my WJ. I bought two blank transponder keys
> on eBay and then had a local locksmith cut and program the first key with
> their computer interface machine using the SKIM code I got from the Jeep
> dealership PARTS department. The cutting and programming cost $24.99 and
> the key blanks were $11.99 each.
>
> I then programmed the second key myself after getting it cut by using the
> directions on http://www.wjjeeps.com/sentry.htm#PROGRAM
>
> I would recommend following the "Quick Steps" as the extra information in
> the "Detailed Steps' initially led to some confusion.
> Quick Steps:
>
> A. Purchase a blank key and have it cut
> B. Insert original key #1 into ignition and turn to On
> C. Wait 5 seconds and turn key to off
> D. Immediately insert original key # 2 into ignition and turn to on
> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> F. Turn ignition off, insert new blank key and turn ignition back on
> G. Once SKIS light stops flashing and turns off, your new key is programmed
>
> The reason I got 2 keys made was so I would have a total of three, if I lost
> one I would not have to pay another programming fee.
>
>
>
>
> "Seahag" <Seahag@toadymail.net> wrote in message
> news:44bd7770_2@newsfeed.slurp.net...
> > Seems to me I remember something about having to have 2 pre-programmed
> > keys to make more. I only got one with my Jeep and the dealer charged $80
> > (40 for parts and 40 for labor) for another one, which we proceeded to
> > lose...
> >
> > Seahag
> >
> > "toxicated101" <matt.wheatley@gmail.com> wrote in message
> > news:1153250560.400565.74140@b28g2000cwb.googlegro ups.com...
> >> Hi
> >>
> >> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
> >> had it cut at my local key cutting store. I have come to follow the
> >> steps but the SKIS indicator light never turns on:
> >>
> >> B. Insert original key #1 into ignition and turn to On
> >> C. Wait 5 seconds and turn key to off
> >> D. Immediately insert original key # 2 into ignition and turn to on
> >> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> >> F. Turn ignition off, insert new blank key and turn ignition back on
> >> G. Once SKIS light stops flashing and turns off, your new key is
> >> programmed
> >>
> >> Both keys I have will start the car, I have put key 1 into the ignition
> >> and turned it it to on (by on I assume its the position that you drive
> >> in rather than the start position) all the indicator light show up the
> >> dash beeps 4 times all light go out, so 5 seconds after turning key is
> >> about the time the beeps stop, turn the key to off (all lights go out)
> >> put the second key in and turn to on, all lights go on, 5 beeps, lights
> >> off, continue waiting but the SKIS indicator never starts to flash.
> >>
> >> Am I doing something wrong , should the jeep beep 4 times ( I assumed
> >> that it is just checking gauges)
> >>
> >> Cheers
> >>
> >> Matt
> >>
> >
> >
Guest
Posts: n/a
Re: new key programming problems
Yes, the dash light is in the shape of a key with a circle around or X
through it. The system will also chime once at the completion of each step
I would try the "Quick Steps" below again exactly as these were what I used
successfully.
The second key you are using. Is it a fully functional key? (as opposed to
an 'emergency or valet" key)
Are you sure it is actually a transponder key? There are non-transponder
keys available that look extremely similar, a locksmith can tell by placing
it in a black box that senses if a chip is present inside the key.
The only other thing that comes to mind is that there is a limit to the
total number of transponder keys (8) that you can program into the memory.
I wonder if it is possible that number has been reached?
If these steps don't program they new key I think you may have to go visit
the dealership. I'll post the entire procedure, per the manual, in a
following post
http://www.wjjeeps.com/sentry.htm#PROGRAM
Quick Steps:
A. Purchase a blank key and have it cut
B. Insert original key #1 into ignition and turn to On
C. Wait 5 seconds and turn key to off
D. Immediately insert original key # 2 into ignition and turn to on
E. Wait 10 seconds for SKIS indicator in dash starts to flash
F. Turn ignition off, insert new blank key and turn ignition back on
G. Once SKIS light stops flashing and turns off, your new key is programmed
"toxicated101" <matt.wheatley@gmail.com> wrote in message
news:1153301534.648194.298960@m79g2000cwm.googlegr oups.com...
> Hi
>
> Maybe I didn't make my self clear, I got the jeep with 2 keys both work
> and start the car, I have now purchased a 3rd key had it cut and it is
> this key I am having problems programming.
>
> Key A (Original Key starts car)
> Key B (Original/spare Key starts car)
> Key C (New Key has been cut, needs programming)
>
> I insert Key A and turn to on, wait between 3 and 15 seconds, turn to
> off.
> I then insert Key B and turn to on (withing 15 seconds) and wait, but
> no SKIS light comes on.
>
> I assume the SKIS light is the one of the picture of the key with the
> line going through it. Which works because it comes on during the
> initial lamp test, you know when you turn the key to on and all the
> lights light up, then go out after a few seconds.
>
> I have followed the instructions , they don't seam so complicated,
> insert one key turn to on wait 5 seconds, turn off, insert key 2 , turn
> to on wait 10 seconds light and a beep should be heard , insert new
> key, but no light or beep.
>
> Is there something I'm missing?
>
> Cheers
>
> Matt
> billy ray wrote:
>> I only got 1 key when I bought my WJ. I bought two blank transponder
>> keys
>> on eBay and then had a local locksmith cut and program the first key
>> with
>> their computer interface machine using the SKIM code I got from the Jeep
>> dealership PARTS department. The cutting and programming cost $24.99 and
>> the key blanks were $11.99 each.
>>
>> I then programmed the second key myself after getting it cut by using the
>> directions on http://www.wjjeeps.com/sentry.htm#PROGRAM
>>
>> I would recommend following the "Quick Steps" as the extra information in
>> the "Detailed Steps' initially led to some confusion.
>> Quick Steps:
>>
>> A. Purchase a blank key and have it cut
>> B. Insert original key #1 into ignition and turn to On
>> C. Wait 5 seconds and turn key to off
>> D. Immediately insert original key # 2 into ignition and turn to on
>> E. Wait 10 seconds for SKIS indicator in dash starts to flash
>> F. Turn ignition off, insert new blank key and turn ignition back on
>> G. Once SKIS light stops flashing and turns off, your new key is
>> programmed
>>
>> The reason I got 2 keys made was so I would have a total of three, if I
>> lost
>> one I would not have to pay another programming fee.
>>
>>
>>
>>
>> "Seahag" <Seahag@toadymail.net> wrote in message
>> news:44bd7770_2@newsfeed.slurp.net...
>> > Seems to me I remember something about having to have 2 pre-programmed
>> > keys to make more. I only got one with my Jeep and the dealer charged
>> > $80
>> > (40 for parts and 40 for labor) for another one, which we proceeded to
>> > lose...
>> >
>> > Seahag
>> >
>> > "toxicated101" <matt.wheatley@gmail.com> wrote in message
>> > news:1153250560.400565.74140@b28g2000cwb.googlegro ups.com...
>> >> Hi
>> >>
>> >> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
>> >> had it cut at my local key cutting store. I have come to follow the
>> >> steps but the SKIS indicator light never turns on:
>> >>
>> >> B. Insert original key #1 into ignition and turn to On
>> >> C. Wait 5 seconds and turn key to off
>> >> D. Immediately insert original key # 2 into ignition and turn to on
>> >> E. Wait 10 seconds for SKIS indicator in dash starts to flash
>> >> F. Turn ignition off, insert new blank key and turn ignition back on
>> >> G. Once SKIS light stops flashing and turns off, your new key is
>> >> programmed
>> >>
>> >> Both keys I have will start the car, I have put key 1 into the
>> >> ignition
>> >> and turned it it to on (by on I assume its the position that you drive
>> >> in rather than the start position) all the indicator light show up the
>> >> dash beeps 4 times all light go out, so 5 seconds after turning key is
>> >> about the time the beeps stop, turn the key to off (all lights go out)
>> >> put the second key in and turn to on, all lights go on, 5 beeps,
>> >> lights
>> >> off, continue waiting but the SKIS indicator never starts to flash.
>> >>
>> >> Am I doing something wrong , should the jeep beep 4 times ( I assumed
>> >> that it is just checking gauges)
>> >>
>> >> Cheers
>> >>
>> >> Matt
>> >>
>> >
>> >
>
through it. The system will also chime once at the completion of each step
I would try the "Quick Steps" below again exactly as these were what I used
successfully.
The second key you are using. Is it a fully functional key? (as opposed to
an 'emergency or valet" key)
Are you sure it is actually a transponder key? There are non-transponder
keys available that look extremely similar, a locksmith can tell by placing
it in a black box that senses if a chip is present inside the key.
The only other thing that comes to mind is that there is a limit to the
total number of transponder keys (8) that you can program into the memory.
I wonder if it is possible that number has been reached?
If these steps don't program they new key I think you may have to go visit
the dealership. I'll post the entire procedure, per the manual, in a
following post
http://www.wjjeeps.com/sentry.htm#PROGRAM
Quick Steps:
A. Purchase a blank key and have it cut
B. Insert original key #1 into ignition and turn to On
C. Wait 5 seconds and turn key to off
D. Immediately insert original key # 2 into ignition and turn to on
E. Wait 10 seconds for SKIS indicator in dash starts to flash
F. Turn ignition off, insert new blank key and turn ignition back on
G. Once SKIS light stops flashing and turns off, your new key is programmed
"toxicated101" <matt.wheatley@gmail.com> wrote in message
news:1153301534.648194.298960@m79g2000cwm.googlegr oups.com...
> Hi
>
> Maybe I didn't make my self clear, I got the jeep with 2 keys both work
> and start the car, I have now purchased a 3rd key had it cut and it is
> this key I am having problems programming.
>
> Key A (Original Key starts car)
> Key B (Original/spare Key starts car)
> Key C (New Key has been cut, needs programming)
>
> I insert Key A and turn to on, wait between 3 and 15 seconds, turn to
> off.
> I then insert Key B and turn to on (withing 15 seconds) and wait, but
> no SKIS light comes on.
>
> I assume the SKIS light is the one of the picture of the key with the
> line going through it. Which works because it comes on during the
> initial lamp test, you know when you turn the key to on and all the
> lights light up, then go out after a few seconds.
>
> I have followed the instructions , they don't seam so complicated,
> insert one key turn to on wait 5 seconds, turn off, insert key 2 , turn
> to on wait 10 seconds light and a beep should be heard , insert new
> key, but no light or beep.
>
> Is there something I'm missing?
>
> Cheers
>
> Matt
> billy ray wrote:
>> I only got 1 key when I bought my WJ. I bought two blank transponder
>> keys
>> on eBay and then had a local locksmith cut and program the first key
>> with
>> their computer interface machine using the SKIM code I got from the Jeep
>> dealership PARTS department. The cutting and programming cost $24.99 and
>> the key blanks were $11.99 each.
>>
>> I then programmed the second key myself after getting it cut by using the
>> directions on http://www.wjjeeps.com/sentry.htm#PROGRAM
>>
>> I would recommend following the "Quick Steps" as the extra information in
>> the "Detailed Steps' initially led to some confusion.
>> Quick Steps:
>>
>> A. Purchase a blank key and have it cut
>> B. Insert original key #1 into ignition and turn to On
>> C. Wait 5 seconds and turn key to off
>> D. Immediately insert original key # 2 into ignition and turn to on
>> E. Wait 10 seconds for SKIS indicator in dash starts to flash
>> F. Turn ignition off, insert new blank key and turn ignition back on
>> G. Once SKIS light stops flashing and turns off, your new key is
>> programmed
>>
>> The reason I got 2 keys made was so I would have a total of three, if I
>> lost
>> one I would not have to pay another programming fee.
>>
>>
>>
>>
>> "Seahag" <Seahag@toadymail.net> wrote in message
>> news:44bd7770_2@newsfeed.slurp.net...
>> > Seems to me I remember something about having to have 2 pre-programmed
>> > keys to make more. I only got one with my Jeep and the dealer charged
>> > $80
>> > (40 for parts and 40 for labor) for another one, which we proceeded to
>> > lose...
>> >
>> > Seahag
>> >
>> > "toxicated101" <matt.wheatley@gmail.com> wrote in message
>> > news:1153250560.400565.74140@b28g2000cwb.googlegro ups.com...
>> >> Hi
>> >>
>> >> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
>> >> had it cut at my local key cutting store. I have come to follow the
>> >> steps but the SKIS indicator light never turns on:
>> >>
>> >> B. Insert original key #1 into ignition and turn to On
>> >> C. Wait 5 seconds and turn key to off
>> >> D. Immediately insert original key # 2 into ignition and turn to on
>> >> E. Wait 10 seconds for SKIS indicator in dash starts to flash
>> >> F. Turn ignition off, insert new blank key and turn ignition back on
>> >> G. Once SKIS light stops flashing and turns off, your new key is
>> >> programmed
>> >>
>> >> Both keys I have will start the car, I have put key 1 into the
>> >> ignition
>> >> and turned it it to on (by on I assume its the position that you drive
>> >> in rather than the start position) all the indicator light show up the
>> >> dash beeps 4 times all light go out, so 5 seconds after turning key is
>> >> about the time the beeps stop, turn the key to off (all lights go out)
>> >> put the second key in and turn to on, all lights go on, 5 beeps,
>> >> lights
>> >> off, continue waiting but the SKIS indicator never starts to flash.
>> >>
>> >> Am I doing something wrong , should the jeep beep 4 times ( I assumed
>> >> that it is just checking gauges)
>> >>
>> >> Cheers
>> >>
>> >> Matt
>> >>
>> >
>> >
>
Guest
Posts: n/a
Re: new key programming problems
Yes, the dash light is in the shape of a key with a circle around or X
through it. The system will also chime once at the completion of each step
I would try the "Quick Steps" below again exactly as these were what I used
successfully.
The second key you are using. Is it a fully functional key? (as opposed to
an 'emergency or valet" key)
Are you sure it is actually a transponder key? There are non-transponder
keys available that look extremely similar, a locksmith can tell by placing
it in a black box that senses if a chip is present inside the key.
The only other thing that comes to mind is that there is a limit to the
total number of transponder keys (8) that you can program into the memory.
I wonder if it is possible that number has been reached?
If these steps don't program they new key I think you may have to go visit
the dealership. I'll post the entire procedure, per the manual, in a
following post
http://www.wjjeeps.com/sentry.htm#PROGRAM
Quick Steps:
A. Purchase a blank key and have it cut
B. Insert original key #1 into ignition and turn to On
C. Wait 5 seconds and turn key to off
D. Immediately insert original key # 2 into ignition and turn to on
E. Wait 10 seconds for SKIS indicator in dash starts to flash
F. Turn ignition off, insert new blank key and turn ignition back on
G. Once SKIS light stops flashing and turns off, your new key is programmed
"toxicated101" <matt.wheatley@gmail.com> wrote in message
news:1153301534.648194.298960@m79g2000cwm.googlegr oups.com...
> Hi
>
> Maybe I didn't make my self clear, I got the jeep with 2 keys both work
> and start the car, I have now purchased a 3rd key had it cut and it is
> this key I am having problems programming.
>
> Key A (Original Key starts car)
> Key B (Original/spare Key starts car)
> Key C (New Key has been cut, needs programming)
>
> I insert Key A and turn to on, wait between 3 and 15 seconds, turn to
> off.
> I then insert Key B and turn to on (withing 15 seconds) and wait, but
> no SKIS light comes on.
>
> I assume the SKIS light is the one of the picture of the key with the
> line going through it. Which works because it comes on during the
> initial lamp test, you know when you turn the key to on and all the
> lights light up, then go out after a few seconds.
>
> I have followed the instructions , they don't seam so complicated,
> insert one key turn to on wait 5 seconds, turn off, insert key 2 , turn
> to on wait 10 seconds light and a beep should be heard , insert new
> key, but no light or beep.
>
> Is there something I'm missing?
>
> Cheers
>
> Matt
> billy ray wrote:
>> I only got 1 key when I bought my WJ. I bought two blank transponder
>> keys
>> on eBay and then had a local locksmith cut and program the first key
>> with
>> their computer interface machine using the SKIM code I got from the Jeep
>> dealership PARTS department. The cutting and programming cost $24.99 and
>> the key blanks were $11.99 each.
>>
>> I then programmed the second key myself after getting it cut by using the
>> directions on http://www.wjjeeps.com/sentry.htm#PROGRAM
>>
>> I would recommend following the "Quick Steps" as the extra information in
>> the "Detailed Steps' initially led to some confusion.
>> Quick Steps:
>>
>> A. Purchase a blank key and have it cut
>> B. Insert original key #1 into ignition and turn to On
>> C. Wait 5 seconds and turn key to off
>> D. Immediately insert original key # 2 into ignition and turn to on
>> E. Wait 10 seconds for SKIS indicator in dash starts to flash
>> F. Turn ignition off, insert new blank key and turn ignition back on
>> G. Once SKIS light stops flashing and turns off, your new key is
>> programmed
>>
>> The reason I got 2 keys made was so I would have a total of three, if I
>> lost
>> one I would not have to pay another programming fee.
>>
>>
>>
>>
>> "Seahag" <Seahag@toadymail.net> wrote in message
>> news:44bd7770_2@newsfeed.slurp.net...
>> > Seems to me I remember something about having to have 2 pre-programmed
>> > keys to make more. I only got one with my Jeep and the dealer charged
>> > $80
>> > (40 for parts and 40 for labor) for another one, which we proceeded to
>> > lose...
>> >
>> > Seahag
>> >
>> > "toxicated101" <matt.wheatley@gmail.com> wrote in message
>> > news:1153250560.400565.74140@b28g2000cwb.googlegro ups.com...
>> >> Hi
>> >>
>> >> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
>> >> had it cut at my local key cutting store. I have come to follow the
>> >> steps but the SKIS indicator light never turns on:
>> >>
>> >> B. Insert original key #1 into ignition and turn to On
>> >> C. Wait 5 seconds and turn key to off
>> >> D. Immediately insert original key # 2 into ignition and turn to on
>> >> E. Wait 10 seconds for SKIS indicator in dash starts to flash
>> >> F. Turn ignition off, insert new blank key and turn ignition back on
>> >> G. Once SKIS light stops flashing and turns off, your new key is
>> >> programmed
>> >>
>> >> Both keys I have will start the car, I have put key 1 into the
>> >> ignition
>> >> and turned it it to on (by on I assume its the position that you drive
>> >> in rather than the start position) all the indicator light show up the
>> >> dash beeps 4 times all light go out, so 5 seconds after turning key is
>> >> about the time the beeps stop, turn the key to off (all lights go out)
>> >> put the second key in and turn to on, all lights go on, 5 beeps,
>> >> lights
>> >> off, continue waiting but the SKIS indicator never starts to flash.
>> >>
>> >> Am I doing something wrong , should the jeep beep 4 times ( I assumed
>> >> that it is just checking gauges)
>> >>
>> >> Cheers
>> >>
>> >> Matt
>> >>
>> >
>> >
>
through it. The system will also chime once at the completion of each step
I would try the "Quick Steps" below again exactly as these were what I used
successfully.
The second key you are using. Is it a fully functional key? (as opposed to
an 'emergency or valet" key)
Are you sure it is actually a transponder key? There are non-transponder
keys available that look extremely similar, a locksmith can tell by placing
it in a black box that senses if a chip is present inside the key.
The only other thing that comes to mind is that there is a limit to the
total number of transponder keys (8) that you can program into the memory.
I wonder if it is possible that number has been reached?
If these steps don't program they new key I think you may have to go visit
the dealership. I'll post the entire procedure, per the manual, in a
following post
http://www.wjjeeps.com/sentry.htm#PROGRAM
Quick Steps:
A. Purchase a blank key and have it cut
B. Insert original key #1 into ignition and turn to On
C. Wait 5 seconds and turn key to off
D. Immediately insert original key # 2 into ignition and turn to on
E. Wait 10 seconds for SKIS indicator in dash starts to flash
F. Turn ignition off, insert new blank key and turn ignition back on
G. Once SKIS light stops flashing and turns off, your new key is programmed
"toxicated101" <matt.wheatley@gmail.com> wrote in message
news:1153301534.648194.298960@m79g2000cwm.googlegr oups.com...
> Hi
>
> Maybe I didn't make my self clear, I got the jeep with 2 keys both work
> and start the car, I have now purchased a 3rd key had it cut and it is
> this key I am having problems programming.
>
> Key A (Original Key starts car)
> Key B (Original/spare Key starts car)
> Key C (New Key has been cut, needs programming)
>
> I insert Key A and turn to on, wait between 3 and 15 seconds, turn to
> off.
> I then insert Key B and turn to on (withing 15 seconds) and wait, but
> no SKIS light comes on.
>
> I assume the SKIS light is the one of the picture of the key with the
> line going through it. Which works because it comes on during the
> initial lamp test, you know when you turn the key to on and all the
> lights light up, then go out after a few seconds.
>
> I have followed the instructions , they don't seam so complicated,
> insert one key turn to on wait 5 seconds, turn off, insert key 2 , turn
> to on wait 10 seconds light and a beep should be heard , insert new
> key, but no light or beep.
>
> Is there something I'm missing?
>
> Cheers
>
> Matt
> billy ray wrote:
>> I only got 1 key when I bought my WJ. I bought two blank transponder
>> keys
>> on eBay and then had a local locksmith cut and program the first key
>> with
>> their computer interface machine using the SKIM code I got from the Jeep
>> dealership PARTS department. The cutting and programming cost $24.99 and
>> the key blanks were $11.99 each.
>>
>> I then programmed the second key myself after getting it cut by using the
>> directions on http://www.wjjeeps.com/sentry.htm#PROGRAM
>>
>> I would recommend following the "Quick Steps" as the extra information in
>> the "Detailed Steps' initially led to some confusion.
>> Quick Steps:
>>
>> A. Purchase a blank key and have it cut
>> B. Insert original key #1 into ignition and turn to On
>> C. Wait 5 seconds and turn key to off
>> D. Immediately insert original key # 2 into ignition and turn to on
>> E. Wait 10 seconds for SKIS indicator in dash starts to flash
>> F. Turn ignition off, insert new blank key and turn ignition back on
>> G. Once SKIS light stops flashing and turns off, your new key is
>> programmed
>>
>> The reason I got 2 keys made was so I would have a total of three, if I
>> lost
>> one I would not have to pay another programming fee.
>>
>>
>>
>>
>> "Seahag" <Seahag@toadymail.net> wrote in message
>> news:44bd7770_2@newsfeed.slurp.net...
>> > Seems to me I remember something about having to have 2 pre-programmed
>> > keys to make more. I only got one with my Jeep and the dealer charged
>> > $80
>> > (40 for parts and 40 for labor) for another one, which we proceeded to
>> > lose...
>> >
>> > Seahag
>> >
>> > "toxicated101" <matt.wheatley@gmail.com> wrote in message
>> > news:1153250560.400565.74140@b28g2000cwb.googlegro ups.com...
>> >> Hi
>> >>
>> >> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
>> >> had it cut at my local key cutting store. I have come to follow the
>> >> steps but the SKIS indicator light never turns on:
>> >>
>> >> B. Insert original key #1 into ignition and turn to On
>> >> C. Wait 5 seconds and turn key to off
>> >> D. Immediately insert original key # 2 into ignition and turn to on
>> >> E. Wait 10 seconds for SKIS indicator in dash starts to flash
>> >> F. Turn ignition off, insert new blank key and turn ignition back on
>> >> G. Once SKIS light stops flashing and turns off, your new key is
>> >> programmed
>> >>
>> >> Both keys I have will start the car, I have put key 1 into the
>> >> ignition
>> >> and turned it it to on (by on I assume its the position that you drive
>> >> in rather than the start position) all the indicator light show up the
>> >> dash beeps 4 times all light go out, so 5 seconds after turning key is
>> >> about the time the beeps stop, turn the key to off (all lights go out)
>> >> put the second key in and turn to on, all lights go on, 5 beeps,
>> >> lights
>> >> off, continue waiting but the SKIS indicator never starts to flash.
>> >>
>> >> Am I doing something wrong , should the jeep beep 4 times ( I assumed
>> >> that it is just checking gauges)
>> >>
>> >> Cheers
>> >>
>> >> Matt
>> >>
>> >
>> >
>
