new key programming problems
#1
Guest
Posts: n/a
new key programming problems
Hi
I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
had it cut at my local key cutting store. I have come to follow the
steps but the SKIS indicator light never turns on:
B. Insert original key #1 into ignition and turn to On
C. Wait 5 seconds and turn key to off
D. Immediately insert original key # 2 into ignition and turn to on
E. Wait 10 seconds for SKIS indicator in dash starts to flash
F. Turn ignition off, insert new blank key and turn ignition back on
G. Once SKIS light stops flashing and turns off, your new key is
programmed
Both keys I have will start the car, I have put key 1 into the ignition
and turned it it to on (by on I assume its the position that you drive
in rather than the start position) all the indicator light show up the
dash beeps 4 times all light go out, so 5 seconds after turning key is
about the time the beeps stop, turn the key to off (all lights go out)
put the second key in and turn to on, all lights go on, 5 beeps, lights
off, continue waiting but the SKIS indicator never starts to flash.
Am I doing something wrong , should the jeep beep 4 times ( I assumed
that it is just checking gauges)
Cheers
Matt
I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
had it cut at my local key cutting store. I have come to follow the
steps but the SKIS indicator light never turns on:
B. Insert original key #1 into ignition and turn to On
C. Wait 5 seconds and turn key to off
D. Immediately insert original key # 2 into ignition and turn to on
E. Wait 10 seconds for SKIS indicator in dash starts to flash
F. Turn ignition off, insert new blank key and turn ignition back on
G. Once SKIS light stops flashing and turns off, your new key is
programmed
Both keys I have will start the car, I have put key 1 into the ignition
and turned it it to on (by on I assume its the position that you drive
in rather than the start position) all the indicator light show up the
dash beeps 4 times all light go out, so 5 seconds after turning key is
about the time the beeps stop, turn the key to off (all lights go out)
put the second key in and turn to on, all lights go on, 5 beeps, lights
off, continue waiting but the SKIS indicator never starts to flash.
Am I doing something wrong , should the jeep beep 4 times ( I assumed
that it is just checking gauges)
Cheers
Matt
#2
Guest
Posts: n/a
Re: new key programming problems
I dunno but I bought a security key for my wife's JGC and it took maybe
a few programming attempts before I figured out the instructions fully
but it finally worked. Several years later the key still works fine.
toxicated101 wrote:
> Hi
>
> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
> had it cut at my local key cutting store. I have come to follow the
> steps but the SKIS indicator light never turns on:
>
> B. Insert original key #1 into ignition and turn to On
> C. Wait 5 seconds and turn key to off
> D. Immediately insert original key # 2 into ignition and turn to on
> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> F. Turn ignition off, insert new blank key and turn ignition back on
> G. Once SKIS light stops flashing and turns off, your new key is
> programmed
>
> Both keys I have will start the car, I have put key 1 into the ignition
> and turned it it to on (by on I assume its the position that you drive
> in rather than the start position) all the indicator light show up the
> dash beeps 4 times all light go out, so 5 seconds after turning key is
> about the time the beeps stop, turn the key to off (all lights go out)
> put the second key in and turn to on, all lights go on, 5 beeps, lights
> off, continue waiting but the SKIS indicator never starts to flash.
>
> Am I doing something wrong , should the jeep beep 4 times ( I assumed
> that it is just checking gauges)
>
> Cheers
>
> Matt
>
--
Jerry Bransford
PP-ASEL N6TAY
See the Geezer Jeep at
http://members.***.net/jerrypb/
a few programming attempts before I figured out the instructions fully
but it finally worked. Several years later the key still works fine.
toxicated101 wrote:
> Hi
>
> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
> had it cut at my local key cutting store. I have come to follow the
> steps but the SKIS indicator light never turns on:
>
> B. Insert original key #1 into ignition and turn to On
> C. Wait 5 seconds and turn key to off
> D. Immediately insert original key # 2 into ignition and turn to on
> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> F. Turn ignition off, insert new blank key and turn ignition back on
> G. Once SKIS light stops flashing and turns off, your new key is
> programmed
>
> Both keys I have will start the car, I have put key 1 into the ignition
> and turned it it to on (by on I assume its the position that you drive
> in rather than the start position) all the indicator light show up the
> dash beeps 4 times all light go out, so 5 seconds after turning key is
> about the time the beeps stop, turn the key to off (all lights go out)
> put the second key in and turn to on, all lights go on, 5 beeps, lights
> off, continue waiting but the SKIS indicator never starts to flash.
>
> Am I doing something wrong , should the jeep beep 4 times ( I assumed
> that it is just checking gauges)
>
> Cheers
>
> Matt
>
--
Jerry Bransford
PP-ASEL N6TAY
See the Geezer Jeep at
http://members.***.net/jerrypb/
#3
Guest
Posts: n/a
Re: new key programming problems
I dunno but I bought a security key for my wife's JGC and it took maybe
a few programming attempts before I figured out the instructions fully
but it finally worked. Several years later the key still works fine.
toxicated101 wrote:
> Hi
>
> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
> had it cut at my local key cutting store. I have come to follow the
> steps but the SKIS indicator light never turns on:
>
> B. Insert original key #1 into ignition and turn to On
> C. Wait 5 seconds and turn key to off
> D. Immediately insert original key # 2 into ignition and turn to on
> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> F. Turn ignition off, insert new blank key and turn ignition back on
> G. Once SKIS light stops flashing and turns off, your new key is
> programmed
>
> Both keys I have will start the car, I have put key 1 into the ignition
> and turned it it to on (by on I assume its the position that you drive
> in rather than the start position) all the indicator light show up the
> dash beeps 4 times all light go out, so 5 seconds after turning key is
> about the time the beeps stop, turn the key to off (all lights go out)
> put the second key in and turn to on, all lights go on, 5 beeps, lights
> off, continue waiting but the SKIS indicator never starts to flash.
>
> Am I doing something wrong , should the jeep beep 4 times ( I assumed
> that it is just checking gauges)
>
> Cheers
>
> Matt
>
--
Jerry Bransford
PP-ASEL N6TAY
See the Geezer Jeep at
http://members.***.net/jerrypb/
a few programming attempts before I figured out the instructions fully
but it finally worked. Several years later the key still works fine.
toxicated101 wrote:
> Hi
>
> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
> had it cut at my local key cutting store. I have come to follow the
> steps but the SKIS indicator light never turns on:
>
> B. Insert original key #1 into ignition and turn to On
> C. Wait 5 seconds and turn key to off
> D. Immediately insert original key # 2 into ignition and turn to on
> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> F. Turn ignition off, insert new blank key and turn ignition back on
> G. Once SKIS light stops flashing and turns off, your new key is
> programmed
>
> Both keys I have will start the car, I have put key 1 into the ignition
> and turned it it to on (by on I assume its the position that you drive
> in rather than the start position) all the indicator light show up the
> dash beeps 4 times all light go out, so 5 seconds after turning key is
> about the time the beeps stop, turn the key to off (all lights go out)
> put the second key in and turn to on, all lights go on, 5 beeps, lights
> off, continue waiting but the SKIS indicator never starts to flash.
>
> Am I doing something wrong , should the jeep beep 4 times ( I assumed
> that it is just checking gauges)
>
> Cheers
>
> Matt
>
--
Jerry Bransford
PP-ASEL N6TAY
See the Geezer Jeep at
http://members.***.net/jerrypb/
#4
Guest
Posts: n/a
Re: new key programming problems
I dunno but I bought a security key for my wife's JGC and it took maybe
a few programming attempts before I figured out the instructions fully
but it finally worked. Several years later the key still works fine.
toxicated101 wrote:
> Hi
>
> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
> had it cut at my local key cutting store. I have come to follow the
> steps but the SKIS indicator light never turns on:
>
> B. Insert original key #1 into ignition and turn to On
> C. Wait 5 seconds and turn key to off
> D. Immediately insert original key # 2 into ignition and turn to on
> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> F. Turn ignition off, insert new blank key and turn ignition back on
> G. Once SKIS light stops flashing and turns off, your new key is
> programmed
>
> Both keys I have will start the car, I have put key 1 into the ignition
> and turned it it to on (by on I assume its the position that you drive
> in rather than the start position) all the indicator light show up the
> dash beeps 4 times all light go out, so 5 seconds after turning key is
> about the time the beeps stop, turn the key to off (all lights go out)
> put the second key in and turn to on, all lights go on, 5 beeps, lights
> off, continue waiting but the SKIS indicator never starts to flash.
>
> Am I doing something wrong , should the jeep beep 4 times ( I assumed
> that it is just checking gauges)
>
> Cheers
>
> Matt
>
--
Jerry Bransford
PP-ASEL N6TAY
See the Geezer Jeep at
http://members.***.net/jerrypb/
a few programming attempts before I figured out the instructions fully
but it finally worked. Several years later the key still works fine.
toxicated101 wrote:
> Hi
>
> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
> had it cut at my local key cutting store. I have come to follow the
> steps but the SKIS indicator light never turns on:
>
> B. Insert original key #1 into ignition and turn to On
> C. Wait 5 seconds and turn key to off
> D. Immediately insert original key # 2 into ignition and turn to on
> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> F. Turn ignition off, insert new blank key and turn ignition back on
> G. Once SKIS light stops flashing and turns off, your new key is
> programmed
>
> Both keys I have will start the car, I have put key 1 into the ignition
> and turned it it to on (by on I assume its the position that you drive
> in rather than the start position) all the indicator light show up the
> dash beeps 4 times all light go out, so 5 seconds after turning key is
> about the time the beeps stop, turn the key to off (all lights go out)
> put the second key in and turn to on, all lights go on, 5 beeps, lights
> off, continue waiting but the SKIS indicator never starts to flash.
>
> Am I doing something wrong , should the jeep beep 4 times ( I assumed
> that it is just checking gauges)
>
> Cheers
>
> Matt
>
--
Jerry Bransford
PP-ASEL N6TAY
See the Geezer Jeep at
http://members.***.net/jerrypb/
#5
Guest
Posts: n/a
Re: new key programming problems
I don't get the problem.....
You say the programming worked fine because the key works right?
Maybe the light bulb is bad?
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
toxicated101 wrote:
>
> Hi
>
> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
> had it cut at my local key cutting store. I have come to follow the
> steps but the SKIS indicator light never turns on:
>
> B. Insert original key #1 into ignition and turn to On
> C. Wait 5 seconds and turn key to off
> D. Immediately insert original key # 2 into ignition and turn to on
> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> F. Turn ignition off, insert new blank key and turn ignition back on
> G. Once SKIS light stops flashing and turns off, your new key is
> programmed
>
> Both keys I have will start the car, I have put key 1 into the ignition
> and turned it it to on (by on I assume its the position that you drive
> in rather than the start position) all the indicator light show up the
> dash beeps 4 times all light go out, so 5 seconds after turning key is
> about the time the beeps stop, turn the key to off (all lights go out)
> put the second key in and turn to on, all lights go on, 5 beeps, lights
> off, continue waiting but the SKIS indicator never starts to flash.
>
> Am I doing something wrong , should the jeep beep 4 times ( I assumed
> that it is just checking gauges)
>
> Cheers
>
> Matt
You say the programming worked fine because the key works right?
Maybe the light bulb is bad?
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
toxicated101 wrote:
>
> Hi
>
> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
> had it cut at my local key cutting store. I have come to follow the
> steps but the SKIS indicator light never turns on:
>
> B. Insert original key #1 into ignition and turn to On
> C. Wait 5 seconds and turn key to off
> D. Immediately insert original key # 2 into ignition and turn to on
> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> F. Turn ignition off, insert new blank key and turn ignition back on
> G. Once SKIS light stops flashing and turns off, your new key is
> programmed
>
> Both keys I have will start the car, I have put key 1 into the ignition
> and turned it it to on (by on I assume its the position that you drive
> in rather than the start position) all the indicator light show up the
> dash beeps 4 times all light go out, so 5 seconds after turning key is
> about the time the beeps stop, turn the key to off (all lights go out)
> put the second key in and turn to on, all lights go on, 5 beeps, lights
> off, continue waiting but the SKIS indicator never starts to flash.
>
> Am I doing something wrong , should the jeep beep 4 times ( I assumed
> that it is just checking gauges)
>
> Cheers
>
> Matt
#6
Guest
Posts: n/a
Re: new key programming problems
I don't get the problem.....
You say the programming worked fine because the key works right?
Maybe the light bulb is bad?
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
toxicated101 wrote:
>
> Hi
>
> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
> had it cut at my local key cutting store. I have come to follow the
> steps but the SKIS indicator light never turns on:
>
> B. Insert original key #1 into ignition and turn to On
> C. Wait 5 seconds and turn key to off
> D. Immediately insert original key # 2 into ignition and turn to on
> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> F. Turn ignition off, insert new blank key and turn ignition back on
> G. Once SKIS light stops flashing and turns off, your new key is
> programmed
>
> Both keys I have will start the car, I have put key 1 into the ignition
> and turned it it to on (by on I assume its the position that you drive
> in rather than the start position) all the indicator light show up the
> dash beeps 4 times all light go out, so 5 seconds after turning key is
> about the time the beeps stop, turn the key to off (all lights go out)
> put the second key in and turn to on, all lights go on, 5 beeps, lights
> off, continue waiting but the SKIS indicator never starts to flash.
>
> Am I doing something wrong , should the jeep beep 4 times ( I assumed
> that it is just checking gauges)
>
> Cheers
>
> Matt
You say the programming worked fine because the key works right?
Maybe the light bulb is bad?
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
toxicated101 wrote:
>
> Hi
>
> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
> had it cut at my local key cutting store. I have come to follow the
> steps but the SKIS indicator light never turns on:
>
> B. Insert original key #1 into ignition and turn to On
> C. Wait 5 seconds and turn key to off
> D. Immediately insert original key # 2 into ignition and turn to on
> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> F. Turn ignition off, insert new blank key and turn ignition back on
> G. Once SKIS light stops flashing and turns off, your new key is
> programmed
>
> Both keys I have will start the car, I have put key 1 into the ignition
> and turned it it to on (by on I assume its the position that you drive
> in rather than the start position) all the indicator light show up the
> dash beeps 4 times all light go out, so 5 seconds after turning key is
> about the time the beeps stop, turn the key to off (all lights go out)
> put the second key in and turn to on, all lights go on, 5 beeps, lights
> off, continue waiting but the SKIS indicator never starts to flash.
>
> Am I doing something wrong , should the jeep beep 4 times ( I assumed
> that it is just checking gauges)
>
> Cheers
>
> Matt
#7
Guest
Posts: n/a
Re: new key programming problems
I don't get the problem.....
You say the programming worked fine because the key works right?
Maybe the light bulb is bad?
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
toxicated101 wrote:
>
> Hi
>
> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
> had it cut at my local key cutting store. I have come to follow the
> steps but the SKIS indicator light never turns on:
>
> B. Insert original key #1 into ignition and turn to On
> C. Wait 5 seconds and turn key to off
> D. Immediately insert original key # 2 into ignition and turn to on
> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> F. Turn ignition off, insert new blank key and turn ignition back on
> G. Once SKIS light stops flashing and turns off, your new key is
> programmed
>
> Both keys I have will start the car, I have put key 1 into the ignition
> and turned it it to on (by on I assume its the position that you drive
> in rather than the start position) all the indicator light show up the
> dash beeps 4 times all light go out, so 5 seconds after turning key is
> about the time the beeps stop, turn the key to off (all lights go out)
> put the second key in and turn to on, all lights go on, 5 beeps, lights
> off, continue waiting but the SKIS indicator never starts to flash.
>
> Am I doing something wrong , should the jeep beep 4 times ( I assumed
> that it is just checking gauges)
>
> Cheers
>
> Matt
You say the programming worked fine because the key works right?
Maybe the light bulb is bad?
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
toxicated101 wrote:
>
> Hi
>
> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
> had it cut at my local key cutting store. I have come to follow the
> steps but the SKIS indicator light never turns on:
>
> B. Insert original key #1 into ignition and turn to On
> C. Wait 5 seconds and turn key to off
> D. Immediately insert original key # 2 into ignition and turn to on
> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> F. Turn ignition off, insert new blank key and turn ignition back on
> G. Once SKIS light stops flashing and turns off, your new key is
> programmed
>
> Both keys I have will start the car, I have put key 1 into the ignition
> and turned it it to on (by on I assume its the position that you drive
> in rather than the start position) all the indicator light show up the
> dash beeps 4 times all light go out, so 5 seconds after turning key is
> about the time the beeps stop, turn the key to off (all lights go out)
> put the second key in and turn to on, all lights go on, 5 beeps, lights
> off, continue waiting but the SKIS indicator never starts to flash.
>
> Am I doing something wrong , should the jeep beep 4 times ( I assumed
> that it is just checking gauges)
>
> Cheers
>
> Matt
#8
Guest
Posts: n/a
Re: new key programming problems
Practice makes perfect: http://www.wjjeeps.com/sentry.htm
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
toxicated101 wrote:
>
> Hi
>
> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
> had it cut at my local key cutting store. I have come to follow the
> steps but the SKIS indicator light never turns on:
>
> B. Insert original key #1 into ignition and turn to On
> C. Wait 5 seconds and turn key to off
> D. Immediately insert original key # 2 into ignition and turn to on
> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> F. Turn ignition off, insert new blank key and turn ignition back on
> G. Once SKIS light stops flashing and turns off, your new key is
> programmed
>
> Both keys I have will start the car, I have put key 1 into the ignition
> and turned it it to on (by on I assume its the position that you drive
> in rather than the start position) all the indicator light show up the
> dash beeps 4 times all light go out, so 5 seconds after turning key is
> about the time the beeps stop, turn the key to off (all lights go out)
> put the second key in and turn to on, all lights go on, 5 beeps, lights
> off, continue waiting but the SKIS indicator never starts to flash.
>
> Am I doing something wrong , should the jeep beep 4 times ( I assumed
> that it is just checking gauges)
>
> Cheers
>
> Matt
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
toxicated101 wrote:
>
> Hi
>
> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
> had it cut at my local key cutting store. I have come to follow the
> steps but the SKIS indicator light never turns on:
>
> B. Insert original key #1 into ignition and turn to On
> C. Wait 5 seconds and turn key to off
> D. Immediately insert original key # 2 into ignition and turn to on
> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> F. Turn ignition off, insert new blank key and turn ignition back on
> G. Once SKIS light stops flashing and turns off, your new key is
> programmed
>
> Both keys I have will start the car, I have put key 1 into the ignition
> and turned it it to on (by on I assume its the position that you drive
> in rather than the start position) all the indicator light show up the
> dash beeps 4 times all light go out, so 5 seconds after turning key is
> about the time the beeps stop, turn the key to off (all lights go out)
> put the second key in and turn to on, all lights go on, 5 beeps, lights
> off, continue waiting but the SKIS indicator never starts to flash.
>
> Am I doing something wrong , should the jeep beep 4 times ( I assumed
> that it is just checking gauges)
>
> Cheers
>
> Matt
#9
Guest
Posts: n/a
Re: new key programming problems
Practice makes perfect: http://www.wjjeeps.com/sentry.htm
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
toxicated101 wrote:
>
> Hi
>
> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
> had it cut at my local key cutting store. I have come to follow the
> steps but the SKIS indicator light never turns on:
>
> B. Insert original key #1 into ignition and turn to On
> C. Wait 5 seconds and turn key to off
> D. Immediately insert original key # 2 into ignition and turn to on
> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> F. Turn ignition off, insert new blank key and turn ignition back on
> G. Once SKIS light stops flashing and turns off, your new key is
> programmed
>
> Both keys I have will start the car, I have put key 1 into the ignition
> and turned it it to on (by on I assume its the position that you drive
> in rather than the start position) all the indicator light show up the
> dash beeps 4 times all light go out, so 5 seconds after turning key is
> about the time the beeps stop, turn the key to off (all lights go out)
> put the second key in and turn to on, all lights go on, 5 beeps, lights
> off, continue waiting but the SKIS indicator never starts to flash.
>
> Am I doing something wrong , should the jeep beep 4 times ( I assumed
> that it is just checking gauges)
>
> Cheers
>
> Matt
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
toxicated101 wrote:
>
> Hi
>
> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
> had it cut at my local key cutting store. I have come to follow the
> steps but the SKIS indicator light never turns on:
>
> B. Insert original key #1 into ignition and turn to On
> C. Wait 5 seconds and turn key to off
> D. Immediately insert original key # 2 into ignition and turn to on
> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> F. Turn ignition off, insert new blank key and turn ignition back on
> G. Once SKIS light stops flashing and turns off, your new key is
> programmed
>
> Both keys I have will start the car, I have put key 1 into the ignition
> and turned it it to on (by on I assume its the position that you drive
> in rather than the start position) all the indicator light show up the
> dash beeps 4 times all light go out, so 5 seconds after turning key is
> about the time the beeps stop, turn the key to off (all lights go out)
> put the second key in and turn to on, all lights go on, 5 beeps, lights
> off, continue waiting but the SKIS indicator never starts to flash.
>
> Am I doing something wrong , should the jeep beep 4 times ( I assumed
> that it is just checking gauges)
>
> Cheers
>
> Matt
#10
Guest
Posts: n/a
Re: new key programming problems
Practice makes perfect: http://www.wjjeeps.com/sentry.htm
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
toxicated101 wrote:
>
> Hi
>
> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
> had it cut at my local key cutting store. I have come to follow the
> steps but the SKIS indicator light never turns on:
>
> B. Insert original key #1 into ignition and turn to On
> C. Wait 5 seconds and turn key to off
> D. Immediately insert original key # 2 into ignition and turn to on
> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> F. Turn ignition off, insert new blank key and turn ignition back on
> G. Once SKIS light stops flashing and turns off, your new key is
> programmed
>
> Both keys I have will start the car, I have put key 1 into the ignition
> and turned it it to on (by on I assume its the position that you drive
> in rather than the start position) all the indicator light show up the
> dash beeps 4 times all light go out, so 5 seconds after turning key is
> about the time the beeps stop, turn the key to off (all lights go out)
> put the second key in and turn to on, all lights go on, 5 beeps, lights
> off, continue waiting but the SKIS indicator never starts to flash.
>
> Am I doing something wrong , should the jeep beep 4 times ( I assumed
> that it is just checking gauges)
>
> Cheers
>
> Matt
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
toxicated101 wrote:
>
> Hi
>
> I have a 2000 Jeep Wrangler. I have just purchased a key from ebay and
> had it cut at my local key cutting store. I have come to follow the
> steps but the SKIS indicator light never turns on:
>
> B. Insert original key #1 into ignition and turn to On
> C. Wait 5 seconds and turn key to off
> D. Immediately insert original key # 2 into ignition and turn to on
> E. Wait 10 seconds for SKIS indicator in dash starts to flash
> F. Turn ignition off, insert new blank key and turn ignition back on
> G. Once SKIS light stops flashing and turns off, your new key is
> programmed
>
> Both keys I have will start the car, I have put key 1 into the ignition
> and turned it it to on (by on I assume its the position that you drive
> in rather than the start position) all the indicator light show up the
> dash beeps 4 times all light go out, so 5 seconds after turning key is
> about the time the beeps stop, turn the key to off (all lights go out)
> put the second key in and turn to on, all lights go on, 5 beeps, lights
> off, continue waiting but the SKIS indicator never starts to flash.
>
> Am I doing something wrong , should the jeep beep 4 times ( I assumed
> that it is just checking gauges)
>
> Cheers
>
> Matt