leaning out the 4.2L
08-08-2005, 05:12 PM
#31
Guest
Posts: n/a
Re: leaning out the 4.2L
The front screws are the main idle mix. Once up in the rpm, it uses the
metering rods in addition.
I 'think' the stepper was still in effect at speed by using the O2
sensor, but wonder about that. There are others here that know the
computer system, maybe one of them will chip in.
The carb needs to be set to best lean mix still, then the computer adds
it's $0.02's worth.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Steve Foley wrote:
>
> I don't know, but I believe so.
>
> Therefore, my addition to this question is:
>
> Are the metering pins/stepper motor/cancerous growth on the BBD only for
> idle mixture?
>
> "Pi-Eyed Piper" <notta@hello.com> wrote in message
> news:FzOJe.172266$9A2.22664@edtnps89...
> > are the mixture screws only for idle mixture?
metering rods in addition.
I 'think' the stepper was still in effect at speed by using the O2
sensor, but wonder about that. There are others here that know the
computer system, maybe one of them will chip in.
The carb needs to be set to best lean mix still, then the computer adds
it's $0.02's worth.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Steve Foley wrote:
>
> I don't know, but I believe so.
>
> Therefore, my addition to this question is:
>
> Are the metering pins/stepper motor/cancerous growth on the BBD only for
> idle mixture?
>
> "Pi-Eyed Piper" <notta@hello.com> wrote in message
> news:FzOJe.172266$9A2.22664@edtnps89...
> > are the mixture screws only for idle mixture?
08-08-2005, 05:12 PM
#32
Guest
Posts: n/a
Re: leaning out the 4.2L
The front screws are the main idle mix. Once up in the rpm, it uses the
metering rods in addition.
I 'think' the stepper was still in effect at speed by using the O2
sensor, but wonder about that. There are others here that know the
computer system, maybe one of them will chip in.
The carb needs to be set to best lean mix still, then the computer adds
it's $0.02's worth.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Steve Foley wrote:
>
> I don't know, but I believe so.
>
> Therefore, my addition to this question is:
>
> Are the metering pins/stepper motor/cancerous growth on the BBD only for
> idle mixture?
>
> "Pi-Eyed Piper" <notta@hello.com> wrote in message
> news:FzOJe.172266$9A2.22664@edtnps89...
> > are the mixture screws only for idle mixture?
metering rods in addition.
I 'think' the stepper was still in effect at speed by using the O2
sensor, but wonder about that. There are others here that know the
computer system, maybe one of them will chip in.
The carb needs to be set to best lean mix still, then the computer adds
it's $0.02's worth.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Steve Foley wrote:
>
> I don't know, but I believe so.
>
> Therefore, my addition to this question is:
>
> Are the metering pins/stepper motor/cancerous growth on the BBD only for
> idle mixture?
>
> "Pi-Eyed Piper" <notta@hello.com> wrote in message
> news:FzOJe.172266$9A2.22664@edtnps89...
> > are the mixture screws only for idle mixture?
08-08-2005, 05:12 PM
#33
Guest
Posts: n/a
Re: leaning out the 4.2L
The front screws are the main idle mix. Once up in the rpm, it uses the
metering rods in addition.
I 'think' the stepper was still in effect at speed by using the O2
sensor, but wonder about that. There are others here that know the
computer system, maybe one of them will chip in.
The carb needs to be set to best lean mix still, then the computer adds
it's $0.02's worth.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Steve Foley wrote:
>
> I don't know, but I believe so.
>
> Therefore, my addition to this question is:
>
> Are the metering pins/stepper motor/cancerous growth on the BBD only for
> idle mixture?
>
> "Pi-Eyed Piper" <notta@hello.com> wrote in message
> news:FzOJe.172266$9A2.22664@edtnps89...
> > are the mixture screws only for idle mixture?
metering rods in addition.
I 'think' the stepper was still in effect at speed by using the O2
sensor, but wonder about that. There are others here that know the
computer system, maybe one of them will chip in.
The carb needs to be set to best lean mix still, then the computer adds
it's $0.02's worth.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Steve Foley wrote:
>
> I don't know, but I believe so.
>
> Therefore, my addition to this question is:
>
> Are the metering pins/stepper motor/cancerous growth on the BBD only for
> idle mixture?
>
> "Pi-Eyed Piper" <notta@hello.com> wrote in message
> news:FzOJe.172266$9A2.22664@edtnps89...
> > are the mixture screws only for idle mixture?
08-08-2005, 05:14 PM
#34
Guest
Posts: n/a
Re: leaning out the 4.2L
Yes, but... The metering rods inside mechanically and vacuum adjust the
high speed in addition to them so if the idle is too rich, it will be
too rich all the way up.
Mike
Pi-Eyed Piper wrote:
>
> Ok, thanks Mike
>
> Does this screw only effect idle mixture?
>
> thanks
> Jason
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:42F7B3D6.1EEEAF5D@sympatico.ca...
> > LOL!
> >
> > I was busy. Clockwise screws it in which leans it out.
> >
> > The stepper's pins go all the way into the carb for a full rich on them,
> > then you fine tune it with the front screws.
> >
> > If it won't lean out, then suspect blocked idle tubes.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > Pi-Eyed Piper wrote:
> >>
> >> Is this such a goofy question no one will answer??
> >>
> >> "Pi-Eyed Piper" <notta@hello.com> wrote in message
> >> news:URLJe.167734$HI.98923@edtnps84...
> >> > on a 4.2L, am I turning counterclockwise to lean the mixture?
> >> >
> >> >
high speed in addition to them so if the idle is too rich, it will be
too rich all the way up.
Mike
Pi-Eyed Piper wrote:
>
> Ok, thanks Mike
>
> Does this screw only effect idle mixture?
>
> thanks
> Jason
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:42F7B3D6.1EEEAF5D@sympatico.ca...
> > LOL!
> >
> > I was busy. Clockwise screws it in which leans it out.
> >
> > The stepper's pins go all the way into the carb for a full rich on them,
> > then you fine tune it with the front screws.
> >
> > If it won't lean out, then suspect blocked idle tubes.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > Pi-Eyed Piper wrote:
> >>
> >> Is this such a goofy question no one will answer??
> >>
> >> "Pi-Eyed Piper" <notta@hello.com> wrote in message
> >> news:URLJe.167734$HI.98923@edtnps84...
> >> > on a 4.2L, am I turning counterclockwise to lean the mixture?
> >> >
> >> >
08-08-2005, 05:14 PM
#35
Guest
Posts: n/a
Re: leaning out the 4.2L
Yes, but... The metering rods inside mechanically and vacuum adjust the
high speed in addition to them so if the idle is too rich, it will be
too rich all the way up.
Mike
Pi-Eyed Piper wrote:
>
> Ok, thanks Mike
>
> Does this screw only effect idle mixture?
>
> thanks
> Jason
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:42F7B3D6.1EEEAF5D@sympatico.ca...
> > LOL!
> >
> > I was busy. Clockwise screws it in which leans it out.
> >
> > The stepper's pins go all the way into the carb for a full rich on them,
> > then you fine tune it with the front screws.
> >
> > If it won't lean out, then suspect blocked idle tubes.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > Pi-Eyed Piper wrote:
> >>
> >> Is this such a goofy question no one will answer??
> >>
> >> "Pi-Eyed Piper" <notta@hello.com> wrote in message
> >> news:URLJe.167734$HI.98923@edtnps84...
> >> > on a 4.2L, am I turning counterclockwise to lean the mixture?
> >> >
> >> >
high speed in addition to them so if the idle is too rich, it will be
too rich all the way up.
Mike
Pi-Eyed Piper wrote:
>
> Ok, thanks Mike
>
> Does this screw only effect idle mixture?
>
> thanks
> Jason
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:42F7B3D6.1EEEAF5D@sympatico.ca...
> > LOL!
> >
> > I was busy. Clockwise screws it in which leans it out.
> >
> > The stepper's pins go all the way into the carb for a full rich on them,
> > then you fine tune it with the front screws.
> >
> > If it won't lean out, then suspect blocked idle tubes.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > Pi-Eyed Piper wrote:
> >>
> >> Is this such a goofy question no one will answer??
> >>
> >> "Pi-Eyed Piper" <notta@hello.com> wrote in message
> >> news:URLJe.167734$HI.98923@edtnps84...
> >> > on a 4.2L, am I turning counterclockwise to lean the mixture?
> >> >
> >> >
08-08-2005, 05:14 PM
#36
Guest
Posts: n/a
Re: leaning out the 4.2L
Yes, but... The metering rods inside mechanically and vacuum adjust the
high speed in addition to them so if the idle is too rich, it will be
too rich all the way up.
Mike
Pi-Eyed Piper wrote:
>
> Ok, thanks Mike
>
> Does this screw only effect idle mixture?
>
> thanks
> Jason
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:42F7B3D6.1EEEAF5D@sympatico.ca...
> > LOL!
> >
> > I was busy. Clockwise screws it in which leans it out.
> >
> > The stepper's pins go all the way into the carb for a full rich on them,
> > then you fine tune it with the front screws.
> >
> > If it won't lean out, then suspect blocked idle tubes.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > Pi-Eyed Piper wrote:
> >>
> >> Is this such a goofy question no one will answer??
> >>
> >> "Pi-Eyed Piper" <notta@hello.com> wrote in message
> >> news:URLJe.167734$HI.98923@edtnps84...
> >> > on a 4.2L, am I turning counterclockwise to lean the mixture?
> >> >
> >> >
high speed in addition to them so if the idle is too rich, it will be
too rich all the way up.
Mike
Pi-Eyed Piper wrote:
>
> Ok, thanks Mike
>
> Does this screw only effect idle mixture?
>
> thanks
> Jason
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:42F7B3D6.1EEEAF5D@sympatico.ca...
> > LOL!
> >
> > I was busy. Clockwise screws it in which leans it out.
> >
> > The stepper's pins go all the way into the carb for a full rich on them,
> > then you fine tune it with the front screws.
> >
> > If it won't lean out, then suspect blocked idle tubes.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > Pi-Eyed Piper wrote:
> >>
> >> Is this such a goofy question no one will answer??
> >>
> >> "Pi-Eyed Piper" <notta@hello.com> wrote in message
> >> news:URLJe.167734$HI.98923@edtnps84...
> >> > on a 4.2L, am I turning counterclockwise to lean the mixture?
> >> >
> >> >
08-08-2005, 05:14 PM
#37
Guest
Posts: n/a
Re: leaning out the 4.2L
Yes, but... The metering rods inside mechanically and vacuum adjust the
high speed in addition to them so if the idle is too rich, it will be
too rich all the way up.
Mike
Pi-Eyed Piper wrote:
>
> Ok, thanks Mike
>
> Does this screw only effect idle mixture?
>
> thanks
> Jason
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:42F7B3D6.1EEEAF5D@sympatico.ca...
> > LOL!
> >
> > I was busy. Clockwise screws it in which leans it out.
> >
> > The stepper's pins go all the way into the carb for a full rich on them,
> > then you fine tune it with the front screws.
> >
> > If it won't lean out, then suspect blocked idle tubes.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > Pi-Eyed Piper wrote:
> >>
> >> Is this such a goofy question no one will answer??
> >>
> >> "Pi-Eyed Piper" <notta@hello.com> wrote in message
> >> news:URLJe.167734$HI.98923@edtnps84...
> >> > on a 4.2L, am I turning counterclockwise to lean the mixture?
> >> >
> >> >
high speed in addition to them so if the idle is too rich, it will be
too rich all the way up.
Mike
Pi-Eyed Piper wrote:
>
> Ok, thanks Mike
>
> Does this screw only effect idle mixture?
>
> thanks
> Jason
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:42F7B3D6.1EEEAF5D@sympatico.ca...
> > LOL!
> >
> > I was busy. Clockwise screws it in which leans it out.
> >
> > The stepper's pins go all the way into the carb for a full rich on them,
> > then you fine tune it with the front screws.
> >
> > If it won't lean out, then suspect blocked idle tubes.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > Pi-Eyed Piper wrote:
> >>
> >> Is this such a goofy question no one will answer??
> >>
> >> "Pi-Eyed Piper" <notta@hello.com> wrote in message
> >> news:URLJe.167734$HI.98923@edtnps84...
> >> > on a 4.2L, am I turning counterclockwise to lean the mixture?
> >> >
> >> >
08-08-2005, 11:47 PM
#38
Guest
Posts: n/a
Re: leaning out the 4.2L
In message <HVOJe.4117$lK2.3895@trndny01>, "Steve Foley" wrote:
>I don't know, but I believe so.
Yes, the "idle mixture screws" are only for idle mixture. However, get them too
rich and they can affect mixture at higher RPM also.
>
>Therefore, my addition to this question is:
>
>Are the metering pins/stepper motor/cancerous growth on the BBD only for
>idle mixture?
No. The stepper motor has 2 pins mounted on it. One is for the idle circuit,
the other is for the main circuit.
>
>
>"Pi-Eyed Piper" <notta@hello.com> wrote in message
>news:FzOJe.172266$9A2.22664@edtnps89...
>> are the mixture screws only for idle mixture?
>
>
>I don't know, but I believe so.
Yes, the "idle mixture screws" are only for idle mixture. However, get them too
rich and they can affect mixture at higher RPM also.
>
>Therefore, my addition to this question is:
>
>Are the metering pins/stepper motor/cancerous growth on the BBD only for
>idle mixture?
No. The stepper motor has 2 pins mounted on it. One is for the idle circuit,
the other is for the main circuit.
>
>
>"Pi-Eyed Piper" <notta@hello.com> wrote in message
>news:FzOJe.172266$9A2.22664@edtnps89...
>> are the mixture screws only for idle mixture?
>
>
08-08-2005, 11:47 PM
#39
Guest
Posts: n/a
Re: leaning out the 4.2L
In message <HVOJe.4117$lK2.3895@trndny01>, "Steve Foley" wrote:
>I don't know, but I believe so.
Yes, the "idle mixture screws" are only for idle mixture. However, get them too
rich and they can affect mixture at higher RPM also.
>
>Therefore, my addition to this question is:
>
>Are the metering pins/stepper motor/cancerous growth on the BBD only for
>idle mixture?
No. The stepper motor has 2 pins mounted on it. One is for the idle circuit,
the other is for the main circuit.
>
>
>"Pi-Eyed Piper" <notta@hello.com> wrote in message
>news:FzOJe.172266$9A2.22664@edtnps89...
>> are the mixture screws only for idle mixture?
>
>
>I don't know, but I believe so.
Yes, the "idle mixture screws" are only for idle mixture. However, get them too
rich and they can affect mixture at higher RPM also.
>
>Therefore, my addition to this question is:
>
>Are the metering pins/stepper motor/cancerous growth on the BBD only for
>idle mixture?
No. The stepper motor has 2 pins mounted on it. One is for the idle circuit,
the other is for the main circuit.
>
>
>"Pi-Eyed Piper" <notta@hello.com> wrote in message
>news:FzOJe.172266$9A2.22664@edtnps89...
>> are the mixture screws only for idle mixture?
>
>
08-08-2005, 11:47 PM
#40
Guest
Posts: n/a
Re: leaning out the 4.2L
In message <HVOJe.4117$lK2.3895@trndny01>, "Steve Foley" wrote:
>I don't know, but I believe so.
Yes, the "idle mixture screws" are only for idle mixture. However, get them too
rich and they can affect mixture at higher RPM also.
>
>Therefore, my addition to this question is:
>
>Are the metering pins/stepper motor/cancerous growth on the BBD only for
>idle mixture?
No. The stepper motor has 2 pins mounted on it. One is for the idle circuit,
the other is for the main circuit.
>
>
>"Pi-Eyed Piper" <notta@hello.com> wrote in message
>news:FzOJe.172266$9A2.22664@edtnps89...
>> are the mixture screws only for idle mixture?
>
>
>I don't know, but I believe so.
Yes, the "idle mixture screws" are only for idle mixture. However, get them too
rich and they can affect mixture at higher RPM also.
>
>Therefore, my addition to this question is:
>
>Are the metering pins/stepper motor/cancerous growth on the BBD only for
>idle mixture?
No. The stepper motor has 2 pins mounted on it. One is for the idle circuit,
the other is for the main circuit.
>
>
>"Pi-Eyed Piper" <notta@hello.com> wrote in message
>news:FzOJe.172266$9A2.22664@edtnps89...
>> are the mixture screws only for idle mixture?
>
>