leaning out the 4.2L
#14
Guest
Posts: n/a
Re: leaning out the 4.2L
Ok, thanks Mike
Does this screw only effect idle mixture?
thanks
Jason
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:42F7B3D6.1EEEAF5D@sympatico.ca...
> LOL!
>
> I was busy. Clockwise screws it in which leans it out.
>
> The stepper's pins go all the way into the carb for a full rich on them,
> then you fine tune it with the front screws.
>
> If it won't lean out, then suspect blocked idle tubes.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> Pi-Eyed Piper wrote:
>>
>> Is this such a goofy question no one will answer??
>>
>> "Pi-Eyed Piper" <notta@hello.com> wrote in message
>> news:URLJe.167734$HI.98923@edtnps84...
>> > on a 4.2L, am I turning counterclockwise to lean the mixture?
>> >
>> >
Does this screw only effect idle mixture?
thanks
Jason
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:42F7B3D6.1EEEAF5D@sympatico.ca...
> LOL!
>
> I was busy. Clockwise screws it in which leans it out.
>
> The stepper's pins go all the way into the carb for a full rich on them,
> then you fine tune it with the front screws.
>
> If it won't lean out, then suspect blocked idle tubes.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> Pi-Eyed Piper wrote:
>>
>> Is this such a goofy question no one will answer??
>>
>> "Pi-Eyed Piper" <notta@hello.com> wrote in message
>> news:URLJe.167734$HI.98923@edtnps84...
>> > on a 4.2L, am I turning counterclockwise to lean the mixture?
>> >
>> >
#15
Guest
Posts: n/a
Re: leaning out the 4.2L
Ok, thanks Mike
Does this screw only effect idle mixture?
thanks
Jason
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:42F7B3D6.1EEEAF5D@sympatico.ca...
> LOL!
>
> I was busy. Clockwise screws it in which leans it out.
>
> The stepper's pins go all the way into the carb for a full rich on them,
> then you fine tune it with the front screws.
>
> If it won't lean out, then suspect blocked idle tubes.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> Pi-Eyed Piper wrote:
>>
>> Is this such a goofy question no one will answer??
>>
>> "Pi-Eyed Piper" <notta@hello.com> wrote in message
>> news:URLJe.167734$HI.98923@edtnps84...
>> > on a 4.2L, am I turning counterclockwise to lean the mixture?
>> >
>> >
Does this screw only effect idle mixture?
thanks
Jason
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:42F7B3D6.1EEEAF5D@sympatico.ca...
> LOL!
>
> I was busy. Clockwise screws it in which leans it out.
>
> The stepper's pins go all the way into the carb for a full rich on them,
> then you fine tune it with the front screws.
>
> If it won't lean out, then suspect blocked idle tubes.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> Pi-Eyed Piper wrote:
>>
>> Is this such a goofy question no one will answer??
>>
>> "Pi-Eyed Piper" <notta@hello.com> wrote in message
>> news:URLJe.167734$HI.98923@edtnps84...
>> > on a 4.2L, am I turning counterclockwise to lean the mixture?
>> >
>> >
#16
Guest
Posts: n/a
Re: leaning out the 4.2L
Ok, thanks Mike
Does this screw only effect idle mixture?
thanks
Jason
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:42F7B3D6.1EEEAF5D@sympatico.ca...
> LOL!
>
> I was busy. Clockwise screws it in which leans it out.
>
> The stepper's pins go all the way into the carb for a full rich on them,
> then you fine tune it with the front screws.
>
> If it won't lean out, then suspect blocked idle tubes.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> Pi-Eyed Piper wrote:
>>
>> Is this such a goofy question no one will answer??
>>
>> "Pi-Eyed Piper" <notta@hello.com> wrote in message
>> news:URLJe.167734$HI.98923@edtnps84...
>> > on a 4.2L, am I turning counterclockwise to lean the mixture?
>> >
>> >
Does this screw only effect idle mixture?
thanks
Jason
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:42F7B3D6.1EEEAF5D@sympatico.ca...
> LOL!
>
> I was busy. Clockwise screws it in which leans it out.
>
> The stepper's pins go all the way into the carb for a full rich on them,
> then you fine tune it with the front screws.
>
> If it won't lean out, then suspect blocked idle tubes.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> Pi-Eyed Piper wrote:
>>
>> Is this such a goofy question no one will answer??
>>
>> "Pi-Eyed Piper" <notta@hello.com> wrote in message
>> news:URLJe.167734$HI.98923@edtnps84...
>> > on a 4.2L, am I turning counterclockwise to lean the mixture?
>> >
>> >
#17
Guest
Posts: n/a
Re: leaning out the 4.2L
Ok, thanks Mike
Does this screw only effect idle mixture?
thanks
Jason
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:42F7B3D6.1EEEAF5D@sympatico.ca...
> LOL!
>
> I was busy. Clockwise screws it in which leans it out.
>
> The stepper's pins go all the way into the carb for a full rich on them,
> then you fine tune it with the front screws.
>
> If it won't lean out, then suspect blocked idle tubes.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> Pi-Eyed Piper wrote:
>>
>> Is this such a goofy question no one will answer??
>>
>> "Pi-Eyed Piper" <notta@hello.com> wrote in message
>> news:URLJe.167734$HI.98923@edtnps84...
>> > on a 4.2L, am I turning counterclockwise to lean the mixture?
>> >
>> >
Does this screw only effect idle mixture?
thanks
Jason
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:42F7B3D6.1EEEAF5D@sympatico.ca...
> LOL!
>
> I was busy. Clockwise screws it in which leans it out.
>
> The stepper's pins go all the way into the carb for a full rich on them,
> then you fine tune it with the front screws.
>
> If it won't lean out, then suspect blocked idle tubes.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> Pi-Eyed Piper wrote:
>>
>> Is this such a goofy question no one will answer??
>>
>> "Pi-Eyed Piper" <notta@hello.com> wrote in message
>> news:URLJe.167734$HI.98923@edtnps84...
>> > on a 4.2L, am I turning counterclockwise to lean the mixture?
>> >
>> >
#18
Guest
Posts: n/a
Re: leaning out the 4.2L
I don't know, but I believe so.
Therefore, my addition to this question is:
Are the metering pins/stepper motor/cancerous growth on the BBD only for
idle mixture?
"Pi-Eyed Piper" <notta@hello.com> wrote in message
news:FzOJe.172266$9A2.22664@edtnps89...
> are the mixture screws only for idle mixture?
Therefore, my addition to this question is:
Are the metering pins/stepper motor/cancerous growth on the BBD only for
idle mixture?
"Pi-Eyed Piper" <notta@hello.com> wrote in message
news:FzOJe.172266$9A2.22664@edtnps89...
> are the mixture screws only for idle mixture?
#19
Guest
Posts: n/a
Re: leaning out the 4.2L
I don't know, but I believe so.
Therefore, my addition to this question is:
Are the metering pins/stepper motor/cancerous growth on the BBD only for
idle mixture?
"Pi-Eyed Piper" <notta@hello.com> wrote in message
news:FzOJe.172266$9A2.22664@edtnps89...
> are the mixture screws only for idle mixture?
Therefore, my addition to this question is:
Are the metering pins/stepper motor/cancerous growth on the BBD only for
idle mixture?
"Pi-Eyed Piper" <notta@hello.com> wrote in message
news:FzOJe.172266$9A2.22664@edtnps89...
> are the mixture screws only for idle mixture?
#20
Guest
Posts: n/a
Re: leaning out the 4.2L
I don't know, but I believe so.
Therefore, my addition to this question is:
Are the metering pins/stepper motor/cancerous growth on the BBD only for
idle mixture?
"Pi-Eyed Piper" <notta@hello.com> wrote in message
news:FzOJe.172266$9A2.22664@edtnps89...
> are the mixture screws only for idle mixture?
Therefore, my addition to this question is:
Are the metering pins/stepper motor/cancerous growth on the BBD only for
idle mixture?
"Pi-Eyed Piper" <notta@hello.com> wrote in message
news:FzOJe.172266$9A2.22664@edtnps89...
> are the mixture screws only for idle mixture?