76 CJ-5 questions.......
Guest
Posts: n/a
Re: 76 CJ-5 questions.......
Steve G wrote:
>
> >
> > 'I' personally find a ported vacuum signal on my distributor gives me an
> > instant punch when I hit the gas, but stock most distributors came with
> > a manifold vacuum or a dual vacuum. The manifold vacuum on them makes
> > the emissions different at idle. You might want to play with that to
> > see which one makes it run best. The ported vacuum nipple is usually up
> > high on the valve cover side and only gets vacuum when the gas pedal
> > opens.
>
> OK i can try that
>
> >
> > Can you explain where the line that was off at the top of the carb runs
> > to?
>
> It went to the vacum canister..connects where it says... "Carb Bowl" on it
That is the 'charcoal' canister or gas tank vent I was talking about. I
can't see the purge valve in your photo. What kind does it have on it?
You have the line that says 'carb bowl', one that says 'Tank' one that
maybe says 'purge?' Are there any more off the top?
Where does the 'purge' line go to? Does it just go to the snorkel end
of the air filter?
>
> >
> > The line from the rear of the valve cover to the air intake is the
> > intake for the PCV system. Filtered air is sucked into the engine at
> > the back as needed and pulled out the front via the PCV valve that is
> > hooked up below the carb. That is also the same vacuum port the brakes
> > would use if you had power brakes.
>
> If air goes from the breather TO the valve cover here... why does oil come
> back in there? maybe thats a silly question, its only a lil bit.
That is called 'blowby'. It happens when either the PCV system isn't
working or when the engine is worn so compression is getting into the
crankcase faster than the PCV can draw it off.
>
> >
> > How is the distributor cap and rotor?
>
> Was new when i bought it, it had been replaced, what else should i look for?
I would open it to look for signs of arcing at the contacts. If the
rotor is a mis match, the cap will arc out fast and show burn marks or
buildup on the contacts. This can cause sputtering.
Mike
>
> >
> > If the EGR isn't hooked up, it isn't likely the cause of the sputter,
> > but as someone else mentioned it can be plated off. Actually is it even
> > hooked up to anything at the bottom??? You have headers and lots of
> > those don't make any provision for the exhaust part of the EGR valve so
> > it could just be in limbo.
>
> Im guessing its in limbo because its hooked to nothing.
> >
> > If the EGR is indeed not connected into the exhaust, then it should be
> > removed and a metal plate put under it or in place of it. If it is
> > leaky, it can cause sputtering issues.
>
> Ill plate it off then.
>
> >
> > Do you have any vacuum lines or parts in the air filter?
>
> Not really a vacum line... but the fresh air line going to the valve cover,
> thats the only thing.
>
> Heres a link to the previous pictures and some new ones i hope helps.
>
> http://hunt101.com/showgallery.php?ppuser=22457&cat=500
>
>
>
>
>
>
>
>
>
> Thanks again for helping me!
>
> >
> > 'I' personally find a ported vacuum signal on my distributor gives me an
> > instant punch when I hit the gas, but stock most distributors came with
> > a manifold vacuum or a dual vacuum. The manifold vacuum on them makes
> > the emissions different at idle. You might want to play with that to
> > see which one makes it run best. The ported vacuum nipple is usually up
> > high on the valve cover side and only gets vacuum when the gas pedal
> > opens.
>
> OK i can try that
>
> >
> > Can you explain where the line that was off at the top of the carb runs
> > to?
>
> It went to the vacum canister..connects where it says... "Carb Bowl" on it
That is the 'charcoal' canister or gas tank vent I was talking about. I
can't see the purge valve in your photo. What kind does it have on it?
You have the line that says 'carb bowl', one that says 'Tank' one that
maybe says 'purge?' Are there any more off the top?
Where does the 'purge' line go to? Does it just go to the snorkel end
of the air filter?
>
> >
> > The line from the rear of the valve cover to the air intake is the
> > intake for the PCV system. Filtered air is sucked into the engine at
> > the back as needed and pulled out the front via the PCV valve that is
> > hooked up below the carb. That is also the same vacuum port the brakes
> > would use if you had power brakes.
>
> If air goes from the breather TO the valve cover here... why does oil come
> back in there? maybe thats a silly question, its only a lil bit.
That is called 'blowby'. It happens when either the PCV system isn't
working or when the engine is worn so compression is getting into the
crankcase faster than the PCV can draw it off.
>
> >
> > How is the distributor cap and rotor?
>
> Was new when i bought it, it had been replaced, what else should i look for?
I would open it to look for signs of arcing at the contacts. If the
rotor is a mis match, the cap will arc out fast and show burn marks or
buildup on the contacts. This can cause sputtering.
Mike
>
> >
> > If the EGR isn't hooked up, it isn't likely the cause of the sputter,
> > but as someone else mentioned it can be plated off. Actually is it even
> > hooked up to anything at the bottom??? You have headers and lots of
> > those don't make any provision for the exhaust part of the EGR valve so
> > it could just be in limbo.
>
> Im guessing its in limbo because its hooked to nothing.
> >
> > If the EGR is indeed not connected into the exhaust, then it should be
> > removed and a metal plate put under it or in place of it. If it is
> > leaky, it can cause sputtering issues.
>
> Ill plate it off then.
>
> >
> > Do you have any vacuum lines or parts in the air filter?
>
> Not really a vacum line... but the fresh air line going to the valve cover,
> thats the only thing.
>
> Heres a link to the previous pictures and some new ones i hope helps.
>
> http://hunt101.com/showgallery.php?ppuser=22457&cat=500
>
>
>
>
>
>
>
>
>
> Thanks again for helping me!
Guest
Posts: n/a
Re: 76 CJ-5 questions.......
Steve G wrote:
>
> >
> > 'I' personally find a ported vacuum signal on my distributor gives me an
> > instant punch when I hit the gas, but stock most distributors came with
> > a manifold vacuum or a dual vacuum. The manifold vacuum on them makes
> > the emissions different at idle. You might want to play with that to
> > see which one makes it run best. The ported vacuum nipple is usually up
> > high on the valve cover side and only gets vacuum when the gas pedal
> > opens.
>
> OK i can try that
>
> >
> > Can you explain where the line that was off at the top of the carb runs
> > to?
>
> It went to the vacum canister..connects where it says... "Carb Bowl" on it
That is the 'charcoal' canister or gas tank vent I was talking about. I
can't see the purge valve in your photo. What kind does it have on it?
You have the line that says 'carb bowl', one that says 'Tank' one that
maybe says 'purge?' Are there any more off the top?
Where does the 'purge' line go to? Does it just go to the snorkel end
of the air filter?
>
> >
> > The line from the rear of the valve cover to the air intake is the
> > intake for the PCV system. Filtered air is sucked into the engine at
> > the back as needed and pulled out the front via the PCV valve that is
> > hooked up below the carb. That is also the same vacuum port the brakes
> > would use if you had power brakes.
>
> If air goes from the breather TO the valve cover here... why does oil come
> back in there? maybe thats a silly question, its only a lil bit.
That is called 'blowby'. It happens when either the PCV system isn't
working or when the engine is worn so compression is getting into the
crankcase faster than the PCV can draw it off.
>
> >
> > How is the distributor cap and rotor?
>
> Was new when i bought it, it had been replaced, what else should i look for?
I would open it to look for signs of arcing at the contacts. If the
rotor is a mis match, the cap will arc out fast and show burn marks or
buildup on the contacts. This can cause sputtering.
Mike
>
> >
> > If the EGR isn't hooked up, it isn't likely the cause of the sputter,
> > but as someone else mentioned it can be plated off. Actually is it even
> > hooked up to anything at the bottom??? You have headers and lots of
> > those don't make any provision for the exhaust part of the EGR valve so
> > it could just be in limbo.
>
> Im guessing its in limbo because its hooked to nothing.
> >
> > If the EGR is indeed not connected into the exhaust, then it should be
> > removed and a metal plate put under it or in place of it. If it is
> > leaky, it can cause sputtering issues.
>
> Ill plate it off then.
>
> >
> > Do you have any vacuum lines or parts in the air filter?
>
> Not really a vacum line... but the fresh air line going to the valve cover,
> thats the only thing.
>
> Heres a link to the previous pictures and some new ones i hope helps.
>
> http://hunt101.com/showgallery.php?ppuser=22457&cat=500
>
>
>
>
>
>
>
>
>
> Thanks again for helping me!
>
> >
> > 'I' personally find a ported vacuum signal on my distributor gives me an
> > instant punch when I hit the gas, but stock most distributors came with
> > a manifold vacuum or a dual vacuum. The manifold vacuum on them makes
> > the emissions different at idle. You might want to play with that to
> > see which one makes it run best. The ported vacuum nipple is usually up
> > high on the valve cover side and only gets vacuum when the gas pedal
> > opens.
>
> OK i can try that
>
> >
> > Can you explain where the line that was off at the top of the carb runs
> > to?
>
> It went to the vacum canister..connects where it says... "Carb Bowl" on it
That is the 'charcoal' canister or gas tank vent I was talking about. I
can't see the purge valve in your photo. What kind does it have on it?
You have the line that says 'carb bowl', one that says 'Tank' one that
maybe says 'purge?' Are there any more off the top?
Where does the 'purge' line go to? Does it just go to the snorkel end
of the air filter?
>
> >
> > The line from the rear of the valve cover to the air intake is the
> > intake for the PCV system. Filtered air is sucked into the engine at
> > the back as needed and pulled out the front via the PCV valve that is
> > hooked up below the carb. That is also the same vacuum port the brakes
> > would use if you had power brakes.
>
> If air goes from the breather TO the valve cover here... why does oil come
> back in there? maybe thats a silly question, its only a lil bit.
That is called 'blowby'. It happens when either the PCV system isn't
working or when the engine is worn so compression is getting into the
crankcase faster than the PCV can draw it off.
>
> >
> > How is the distributor cap and rotor?
>
> Was new when i bought it, it had been replaced, what else should i look for?
I would open it to look for signs of arcing at the contacts. If the
rotor is a mis match, the cap will arc out fast and show burn marks or
buildup on the contacts. This can cause sputtering.
Mike
>
> >
> > If the EGR isn't hooked up, it isn't likely the cause of the sputter,
> > but as someone else mentioned it can be plated off. Actually is it even
> > hooked up to anything at the bottom??? You have headers and lots of
> > those don't make any provision for the exhaust part of the EGR valve so
> > it could just be in limbo.
>
> Im guessing its in limbo because its hooked to nothing.
> >
> > If the EGR is indeed not connected into the exhaust, then it should be
> > removed and a metal plate put under it or in place of it. If it is
> > leaky, it can cause sputtering issues.
>
> Ill plate it off then.
>
> >
> > Do you have any vacuum lines or parts in the air filter?
>
> Not really a vacum line... but the fresh air line going to the valve cover,
> thats the only thing.
>
> Heres a link to the previous pictures and some new ones i hope helps.
>
> http://hunt101.com/showgallery.php?ppuser=22457&cat=500
>
>
>
>
>
>
>
>
>
> Thanks again for helping me!
Guest
Posts: n/a
Re: 76 CJ-5 questions.......
Steve G wrote:
>
> >
> > 'I' personally find a ported vacuum signal on my distributor gives me an
> > instant punch when I hit the gas, but stock most distributors came with
> > a manifold vacuum or a dual vacuum. The manifold vacuum on them makes
> > the emissions different at idle. You might want to play with that to
> > see which one makes it run best. The ported vacuum nipple is usually up
> > high on the valve cover side and only gets vacuum when the gas pedal
> > opens.
>
> OK i can try that
>
> >
> > Can you explain where the line that was off at the top of the carb runs
> > to?
>
> It went to the vacum canister..connects where it says... "Carb Bowl" on it
That is the 'charcoal' canister or gas tank vent I was talking about. I
can't see the purge valve in your photo. What kind does it have on it?
You have the line that says 'carb bowl', one that says 'Tank' one that
maybe says 'purge?' Are there any more off the top?
Where does the 'purge' line go to? Does it just go to the snorkel end
of the air filter?
>
> >
> > The line from the rear of the valve cover to the air intake is the
> > intake for the PCV system. Filtered air is sucked into the engine at
> > the back as needed and pulled out the front via the PCV valve that is
> > hooked up below the carb. That is also the same vacuum port the brakes
> > would use if you had power brakes.
>
> If air goes from the breather TO the valve cover here... why does oil come
> back in there? maybe thats a silly question, its only a lil bit.
That is called 'blowby'. It happens when either the PCV system isn't
working or when the engine is worn so compression is getting into the
crankcase faster than the PCV can draw it off.
>
> >
> > How is the distributor cap and rotor?
>
> Was new when i bought it, it had been replaced, what else should i look for?
I would open it to look for signs of arcing at the contacts. If the
rotor is a mis match, the cap will arc out fast and show burn marks or
buildup on the contacts. This can cause sputtering.
Mike
>
> >
> > If the EGR isn't hooked up, it isn't likely the cause of the sputter,
> > but as someone else mentioned it can be plated off. Actually is it even
> > hooked up to anything at the bottom??? You have headers and lots of
> > those don't make any provision for the exhaust part of the EGR valve so
> > it could just be in limbo.
>
> Im guessing its in limbo because its hooked to nothing.
> >
> > If the EGR is indeed not connected into the exhaust, then it should be
> > removed and a metal plate put under it or in place of it. If it is
> > leaky, it can cause sputtering issues.
>
> Ill plate it off then.
>
> >
> > Do you have any vacuum lines or parts in the air filter?
>
> Not really a vacum line... but the fresh air line going to the valve cover,
> thats the only thing.
>
> Heres a link to the previous pictures and some new ones i hope helps.
>
> http://hunt101.com/showgallery.php?ppuser=22457&cat=500
>
>
>
>
>
>
>
>
>
> Thanks again for helping me!
>
> >
> > 'I' personally find a ported vacuum signal on my distributor gives me an
> > instant punch when I hit the gas, but stock most distributors came with
> > a manifold vacuum or a dual vacuum. The manifold vacuum on them makes
> > the emissions different at idle. You might want to play with that to
> > see which one makes it run best. The ported vacuum nipple is usually up
> > high on the valve cover side and only gets vacuum when the gas pedal
> > opens.
>
> OK i can try that
>
> >
> > Can you explain where the line that was off at the top of the carb runs
> > to?
>
> It went to the vacum canister..connects where it says... "Carb Bowl" on it
That is the 'charcoal' canister or gas tank vent I was talking about. I
can't see the purge valve in your photo. What kind does it have on it?
You have the line that says 'carb bowl', one that says 'Tank' one that
maybe says 'purge?' Are there any more off the top?
Where does the 'purge' line go to? Does it just go to the snorkel end
of the air filter?
>
> >
> > The line from the rear of the valve cover to the air intake is the
> > intake for the PCV system. Filtered air is sucked into the engine at
> > the back as needed and pulled out the front via the PCV valve that is
> > hooked up below the carb. That is also the same vacuum port the brakes
> > would use if you had power brakes.
>
> If air goes from the breather TO the valve cover here... why does oil come
> back in there? maybe thats a silly question, its only a lil bit.
That is called 'blowby'. It happens when either the PCV system isn't
working or when the engine is worn so compression is getting into the
crankcase faster than the PCV can draw it off.
>
> >
> > How is the distributor cap and rotor?
>
> Was new when i bought it, it had been replaced, what else should i look for?
I would open it to look for signs of arcing at the contacts. If the
rotor is a mis match, the cap will arc out fast and show burn marks or
buildup on the contacts. This can cause sputtering.
Mike
>
> >
> > If the EGR isn't hooked up, it isn't likely the cause of the sputter,
> > but as someone else mentioned it can be plated off. Actually is it even
> > hooked up to anything at the bottom??? You have headers and lots of
> > those don't make any provision for the exhaust part of the EGR valve so
> > it could just be in limbo.
>
> Im guessing its in limbo because its hooked to nothing.
> >
> > If the EGR is indeed not connected into the exhaust, then it should be
> > removed and a metal plate put under it or in place of it. If it is
> > leaky, it can cause sputtering issues.
>
> Ill plate it off then.
>
> >
> > Do you have any vacuum lines or parts in the air filter?
>
> Not really a vacum line... but the fresh air line going to the valve cover,
> thats the only thing.
>
> Heres a link to the previous pictures and some new ones i hope helps.
>
> http://hunt101.com/showgallery.php?ppuser=22457&cat=500
>
>
>
>
>
>
>
>
>
> Thanks again for helping me!
Guest
Posts: n/a
Re: 76 CJ-5 questions.......
> That is the 'charcoal' canister or gas tank vent I was talking about. I
> can't see the purge valve in your photo. What kind does it have on it?
> You have the line that says 'carb bowl', one that says 'Tank' one that
> maybe says 'purge?' Are there any more off the top?
Nope, i took it completly out of its bracket.. only 3 ports on it..
Tank...Carb Bowl...Purge
>
> Where does the 'purge' line go to? Does it just go to the snorkel end
> of the air filter?
about 6" worth of hose open to fresh air
> I would open it to look for signs of arcing at the contacts. If the
> rotor is a mis match, the cap will arc out fast and show burn marks or
> buildup on the contacts. This can cause sputtering.
>
Looks clean on the edge of the button and the inside of the cap
Guest
Posts: n/a
Re: 76 CJ-5 questions.......
> That is the 'charcoal' canister or gas tank vent I was talking about. I
> can't see the purge valve in your photo. What kind does it have on it?
> You have the line that says 'carb bowl', one that says 'Tank' one that
> maybe says 'purge?' Are there any more off the top?
Nope, i took it completly out of its bracket.. only 3 ports on it..
Tank...Carb Bowl...Purge
>
> Where does the 'purge' line go to? Does it just go to the snorkel end
> of the air filter?
about 6" worth of hose open to fresh air
> I would open it to look for signs of arcing at the contacts. If the
> rotor is a mis match, the cap will arc out fast and show burn marks or
> buildup on the contacts. This can cause sputtering.
>
Looks clean on the edge of the button and the inside of the cap
Guest
Posts: n/a
Re: 76 CJ-5 questions.......
> That is the 'charcoal' canister or gas tank vent I was talking about. I
> can't see the purge valve in your photo. What kind does it have on it?
> You have the line that says 'carb bowl', one that says 'Tank' one that
> maybe says 'purge?' Are there any more off the top?
Nope, i took it completly out of its bracket.. only 3 ports on it..
Tank...Carb Bowl...Purge
>
> Where does the 'purge' line go to? Does it just go to the snorkel end
> of the air filter?
about 6" worth of hose open to fresh air
> I would open it to look for signs of arcing at the contacts. If the
> rotor is a mis match, the cap will arc out fast and show burn marks or
> buildup on the contacts. This can cause sputtering.
>
Looks clean on the edge of the button and the inside of the cap
Guest
Posts: n/a
Re: 76 CJ-5 questions.......
> That is the 'charcoal' canister or gas tank vent I was talking about. I
> can't see the purge valve in your photo. What kind does it have on it?
> You have the line that says 'carb bowl', one that says 'Tank' one that
> maybe says 'purge?' Are there any more off the top?
Nope, i took it completly out of its bracket.. only 3 ports on it..
Tank...Carb Bowl...Purge
>
> Where does the 'purge' line go to? Does it just go to the snorkel end
> of the air filter?
about 6" worth of hose open to fresh air
> I would open it to look for signs of arcing at the contacts. If the
> rotor is a mis match, the cap will arc out fast and show burn marks or
> buildup on the contacts. This can cause sputtering.
>
Looks clean on the edge of the button and the inside of the cap
Guest
Posts: n/a
Re: 76 CJ-5 questions.......
Ok, stock I believe there should be a nipple on the bottom of the air
filter intake snorkel. The venturi effect there sucks the fumes out of
the activated charcoal that is in the canister.
The canister has a $2.00 air filter on the bottom that is usually just
called an emissions filter. The old filter is a bugger to dig out and
then the new one just tucks in.
How are the wires? I had a miss and a sputter at idle the other day and
one of my plug wires had vibrated loose. Plugged it back and it purrs
again.
Mike
Steve G wrote:
>
> > That is the 'charcoal' canister or gas tank vent I was talking about. I
> > can't see the purge valve in your photo. What kind does it have on it?
> > You have the line that says 'carb bowl', one that says 'Tank' one that
> > maybe says 'purge?' Are there any more off the top?
>
> Nope, i took it completly out of its bracket.. only 3 ports on it..
> Tank...Carb Bowl...Purge
>
> >
> > Where does the 'purge' line go to? Does it just go to the snorkel end
> > of the air filter?
>
> about 6" worth of hose open to fresh air
>
> > I would open it to look for signs of arcing at the contacts. If the
> > rotor is a mis match, the cap will arc out fast and show burn marks or
> > buildup on the contacts. This can cause sputtering.
> >
> Looks clean on the edge of the button and the inside of the cap
filter intake snorkel. The venturi effect there sucks the fumes out of
the activated charcoal that is in the canister.
The canister has a $2.00 air filter on the bottom that is usually just
called an emissions filter. The old filter is a bugger to dig out and
then the new one just tucks in.
How are the wires? I had a miss and a sputter at idle the other day and
one of my plug wires had vibrated loose. Plugged it back and it purrs
again.
Mike
Steve G wrote:
>
> > That is the 'charcoal' canister or gas tank vent I was talking about. I
> > can't see the purge valve in your photo. What kind does it have on it?
> > You have the line that says 'carb bowl', one that says 'Tank' one that
> > maybe says 'purge?' Are there any more off the top?
>
> Nope, i took it completly out of its bracket.. only 3 ports on it..
> Tank...Carb Bowl...Purge
>
> >
> > Where does the 'purge' line go to? Does it just go to the snorkel end
> > of the air filter?
>
> about 6" worth of hose open to fresh air
>
> > I would open it to look for signs of arcing at the contacts. If the
> > rotor is a mis match, the cap will arc out fast and show burn marks or
> > buildup on the contacts. This can cause sputtering.
> >
> Looks clean on the edge of the button and the inside of the cap
Guest
Posts: n/a
Re: 76 CJ-5 questions.......
Ok, stock I believe there should be a nipple on the bottom of the air
filter intake snorkel. The venturi effect there sucks the fumes out of
the activated charcoal that is in the canister.
The canister has a $2.00 air filter on the bottom that is usually just
called an emissions filter. The old filter is a bugger to dig out and
then the new one just tucks in.
How are the wires? I had a miss and a sputter at idle the other day and
one of my plug wires had vibrated loose. Plugged it back and it purrs
again.
Mike
Steve G wrote:
>
> > That is the 'charcoal' canister or gas tank vent I was talking about. I
> > can't see the purge valve in your photo. What kind does it have on it?
> > You have the line that says 'carb bowl', one that says 'Tank' one that
> > maybe says 'purge?' Are there any more off the top?
>
> Nope, i took it completly out of its bracket.. only 3 ports on it..
> Tank...Carb Bowl...Purge
>
> >
> > Where does the 'purge' line go to? Does it just go to the snorkel end
> > of the air filter?
>
> about 6" worth of hose open to fresh air
>
> > I would open it to look for signs of arcing at the contacts. If the
> > rotor is a mis match, the cap will arc out fast and show burn marks or
> > buildup on the contacts. This can cause sputtering.
> >
> Looks clean on the edge of the button and the inside of the cap
filter intake snorkel. The venturi effect there sucks the fumes out of
the activated charcoal that is in the canister.
The canister has a $2.00 air filter on the bottom that is usually just
called an emissions filter. The old filter is a bugger to dig out and
then the new one just tucks in.
How are the wires? I had a miss and a sputter at idle the other day and
one of my plug wires had vibrated loose. Plugged it back and it purrs
again.
Mike
Steve G wrote:
>
> > That is the 'charcoal' canister or gas tank vent I was talking about. I
> > can't see the purge valve in your photo. What kind does it have on it?
> > You have the line that says 'carb bowl', one that says 'Tank' one that
> > maybe says 'purge?' Are there any more off the top?
>
> Nope, i took it completly out of its bracket.. only 3 ports on it..
> Tank...Carb Bowl...Purge
>
> >
> > Where does the 'purge' line go to? Does it just go to the snorkel end
> > of the air filter?
>
> about 6" worth of hose open to fresh air
>
> > I would open it to look for signs of arcing at the contacts. If the
> > rotor is a mis match, the cap will arc out fast and show burn marks or
> > buildup on the contacts. This can cause sputtering.
> >
> Looks clean on the edge of the button and the inside of the cap
Guest
Posts: n/a
Re: 76 CJ-5 questions.......
Ok, stock I believe there should be a nipple on the bottom of the air
filter intake snorkel. The venturi effect there sucks the fumes out of
the activated charcoal that is in the canister.
The canister has a $2.00 air filter on the bottom that is usually just
called an emissions filter. The old filter is a bugger to dig out and
then the new one just tucks in.
How are the wires? I had a miss and a sputter at idle the other day and
one of my plug wires had vibrated loose. Plugged it back and it purrs
again.
Mike
Steve G wrote:
>
> > That is the 'charcoal' canister or gas tank vent I was talking about. I
> > can't see the purge valve in your photo. What kind does it have on it?
> > You have the line that says 'carb bowl', one that says 'Tank' one that
> > maybe says 'purge?' Are there any more off the top?
>
> Nope, i took it completly out of its bracket.. only 3 ports on it..
> Tank...Carb Bowl...Purge
>
> >
> > Where does the 'purge' line go to? Does it just go to the snorkel end
> > of the air filter?
>
> about 6" worth of hose open to fresh air
>
> > I would open it to look for signs of arcing at the contacts. If the
> > rotor is a mis match, the cap will arc out fast and show burn marks or
> > buildup on the contacts. This can cause sputtering.
> >
> Looks clean on the edge of the button and the inside of the cap
filter intake snorkel. The venturi effect there sucks the fumes out of
the activated charcoal that is in the canister.
The canister has a $2.00 air filter on the bottom that is usually just
called an emissions filter. The old filter is a bugger to dig out and
then the new one just tucks in.
How are the wires? I had a miss and a sputter at idle the other day and
one of my plug wires had vibrated loose. Plugged it back and it purrs
again.
Mike
Steve G wrote:
>
> > That is the 'charcoal' canister or gas tank vent I was talking about. I
> > can't see the purge valve in your photo. What kind does it have on it?
> > You have the line that says 'carb bowl', one that says 'Tank' one that
> > maybe says 'purge?' Are there any more off the top?
>
> Nope, i took it completly out of its bracket.. only 3 ports on it..
> Tank...Carb Bowl...Purge
>
> >
> > Where does the 'purge' line go to? Does it just go to the snorkel end
> > of the air filter?
>
> about 6" worth of hose open to fresh air
>
> > I would open it to look for signs of arcing at the contacts. If the
> > rotor is a mis match, the cap will arc out fast and show burn marks or
> > buildup on the contacts. This can cause sputtering.
> >
> Looks clean on the edge of the button and the inside of the cap
