RIM SIZE FOR 2006 WRANGLER X
#251
Guest
Posts: n/a
Re: RIM SIZE FOR 2006 WRANGLER X
? "Tracie" <brainart@upstate.edu> ?????? ??? ??????
news:1188219739.873279.122920@r34g2000hsd.googlegr oups.com...
On Aug 27, 8:25 am, "Bill Spiliotopoulos" <vsp...@yahoo.com> wrote:
> A correction,
> Caster angles should be positive (7 degrees), not negative.
>
> Ï "Bill Spiliotopoulos" <vsp...@yahoo.com> Ýãñáøå óôï
> ìÞíõìánews:faudc7$e95$1@ulysses.noc.ntua.gr...
>
>
>
> >I have to remind you that the TJ has a coil sprung suspension with upper
> >and lower arms, which alter the pinion angle when it is raised - lowered,
> >unlike the leaf sprung suspensions which keep the pinion angle constant.
>
> > Raising 2" does create driveline vibes because the rear pinion is no
> > longer parallel to the transfer case output shaft.
> > You can chose to ignore them or may not notice they are there, but the
> > truth is that they exist.
> > I have seen TJ of friends of mine that said they didn't have any
> > driveline
> > vibes after a 2" lift, but when I drove their rig I could feel the
> > difference. With a mismatch in pinion - output shaft angle, it feels
> > like
> > the engine is running rough and they blame the engine or the exhaust.
> > The
> > only way to convince them was to drop their thansfer case 1/2 inch and
> > ask
> > them if they cound feel the difference, which they could.
>
> > Yes, the TJ has a double cardan joint in the transfer case front end,
> > which requires the pinion angle to be set almost parallel to the
> > driveshaft (0.5 degrees lower). You won't notice driveline vibes when in
> > 2wd mode though. But the front pinion angle also affects the front
> > caster
> > angle.
> > By raising 2" in the TJ, the caster increases from -7 degrees to
> > about -5.
> > The front pinion also gets 2 degrees higher than the driveshaft. By
> > re-adjusting the front pinion angle, you fix the caster angle also. When
> > the front pinion is adjusted properly, you loose only 0.3 degrees of
> > caster angle for the 2" lift compared to the factory caster setting.
>
> > Now I speak all this from personal experience on the exact same vehicle
> > as
> > the O.P., as I have installed the same lift on my TJ and setting the
> > pinion angles was what made it to ride smooth like stock again.
>
> > About adding cargo and upsetting the rear driveline angle to create
> > vibes,
> > this is what happens in the TJ.
> > There is a range that the pinion angle may be off, which doesn't create
> > noticeable vibes. The rear pinion is set to the upper side of this
> > range.
> > When you load the TJ and the suspension its lower, the rear pinion will
> > operate to the lower side of the range, and you won't get any vibes.
> > With
> > slight load, the pinion angle is at the center of the range and it feels
> > like running a bit smoother. But if you remove the hardtop and the rear
> > seat, which makes the suspension sit higher, you will notice driveline
> > vibes.
>
> > Bill Spiliotopoulos,
> > '96 XJ,
> > '06 TJ.
>
> > ? "Mike Romain" <roma...@sympatico.ca> ?????? ??? ??????
> >news:46cedfd9$0$5203$9a6e19ea@unlimited.newshosti ng.com...
> >> What 'are' you talking about?
>
> >> The front has a double cardan or CV joint already so needs 'no
> >> tweaking'
> >> at all even for a larger lift and a 2" is not going to change the rear
> >> enough to matter.
>
> >> You get that much/more change with a load on or off.
>
> >> By your reckoning if I put 4 people and gear in my Jeep, it won't drive
> >> because my height will be off by at least 2".
>
> >> Mike
> >> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> >> 88 Cherokee 235 BFG AT's - Gone to the rust pile...
> >> Canadian Off Road Trips Photos: Non members can still view!
> >> Jan/06http://www.imagestation.com/album/pictures.html?id=2115147590
> >> (More Off Road album links at bottom of the view page)
>
> >> Bill Spiliotopoulos wrote:
> >>>> 2.) With the 2" spacer lift, would I have to drop the t-case or do
> >>>> any other mods besides slapping it on?
>
> >>> Yes.
>
> >>> You have to turn the rear axle forward, so that the pinion axis is
> >>> almost parallel (a bit lower) to the transfer case output shaft. Or
> >>> drop the transfer case 1/2 inch. Turning the rear axle forward will
> >>> cost
> >>> more if you have a shop do it for you (requires either adjustable
> >>> lower
> >>> arms, or elongating the upper arms rear mounting holes and installing
> >>> an
> >>> eccentric washer to set the pinion angle). You may not be sensitive
> >>> enough to feel the vibes, but even with 1 inch lift, the pinion angle
> >>> gets misaligned, increasing mechanical noise and u-joint wear.
>
> >>> You also MUST rotate the front axle towards the rear to make the
> >>> pinion
> >>> axis parallel with the front driveshaft.
> >>> This will restore the caster angle to factory specification, which is
> >>> very important to limit the occurence of death wobble. The toe-in on
> >>> the front axle must be set after the pinion angle is set for the front
> >>> axle.
>
> >>> The 2" spacer lift and 31" M/T tire combination is a very good
> >>> combination. If you disconnect the front sway-bar the off-road
> >>> capability of your rig will be dramatically increased compared to what
> >>> it is right now. With the say-bar connected, your on-road behavior
> >>> will
> >>> not be much affected.
> >>> This is a picture of a 2006 TJ with 2" spacer lift and 235R15 tires
> >>> with
> >>> the swaay-bar disconnected.
> >>>http://alma-tech.com/tmp/tj_flex.jpg
>
> >>> But you must find a shop that is willing to deal with all the "minor"
> >>> details required to make the car run comfortable and safe as it was
> >>> prior to the lift (fine tune the pinion angles).
>
> >>> Bill Spiliotopoulos,
> >>> '96 XJ
> >>> '06 TJ.- Hide quoted text -
>
> - Show quoted text -
>
>So what you're saying is this:
>
>I get a 2.25 inch spacer lift with new shocks
>
>When I do get this lift setup, I will have to do two things: a.) drop
>the transfer case 1/2 inch, and b.) readjust the FRONT pinion angle
>which in turn readjusts the caster angle.
>
>Will I have to adjust the REAR trackbar as well with a trackbar
>relocation bracket?
>
>THANKS
Hi Tracie,
1)
2.25" inch spacers should be used if you remove the existing 0.25 factory
installed spacers/isolators in the TJ.
More than 2" spacer lift is not recomended.
If you get the 2" spacers, you must use them together with the factory 0.25
spacers to achieve the 2" lift.
2)
I have dropped the transfer case about 1/2 inch, but I have the D44 rear,
which has a shorter driveshaft and the pinion angle is affected more by the
lift, than a D35.
On the 2006 TJ model, if you have ABS, you have the D44. Otherwise you have
the D35.
I would recomend to you to drop the transfer case by gradually stacking wide
washers between the frame and skid
plate, until the engine doesn't feel rough when accelerating uphill in 1st
or 2nd gear. You will need to replace the 6 transfer case bolts with longer
ones. Start with 4 washers 2mm thick, and add up to 6 or 7. Use the widest
washers you can get (at least 1" diameter).
Bill Spiliotopoulos,
'96 XJ
'06 TJ.
#252
Guest
Posts: n/a
Re: RIM SIZE FOR 2006 WRANGLER X
? "Tracie" <brainart@upstate.edu> ?????? ??? ??????
news:1188219739.873279.122920@r34g2000hsd.googlegr oups.com...
On Aug 27, 8:25 am, "Bill Spiliotopoulos" <vsp...@yahoo.com> wrote:
> A correction,
> Caster angles should be positive (7 degrees), not negative.
>
> Ï "Bill Spiliotopoulos" <vsp...@yahoo.com> Ýãñáøå óôï
> ìÞíõìánews:faudc7$e95$1@ulysses.noc.ntua.gr...
>
>
>
> >I have to remind you that the TJ has a coil sprung suspension with upper
> >and lower arms, which alter the pinion angle when it is raised - lowered,
> >unlike the leaf sprung suspensions which keep the pinion angle constant.
>
> > Raising 2" does create driveline vibes because the rear pinion is no
> > longer parallel to the transfer case output shaft.
> > You can chose to ignore them or may not notice they are there, but the
> > truth is that they exist.
> > I have seen TJ of friends of mine that said they didn't have any
> > driveline
> > vibes after a 2" lift, but when I drove their rig I could feel the
> > difference. With a mismatch in pinion - output shaft angle, it feels
> > like
> > the engine is running rough and they blame the engine or the exhaust.
> > The
> > only way to convince them was to drop their thansfer case 1/2 inch and
> > ask
> > them if they cound feel the difference, which they could.
>
> > Yes, the TJ has a double cardan joint in the transfer case front end,
> > which requires the pinion angle to be set almost parallel to the
> > driveshaft (0.5 degrees lower). You won't notice driveline vibes when in
> > 2wd mode though. But the front pinion angle also affects the front
> > caster
> > angle.
> > By raising 2" in the TJ, the caster increases from -7 degrees to
> > about -5.
> > The front pinion also gets 2 degrees higher than the driveshaft. By
> > re-adjusting the front pinion angle, you fix the caster angle also. When
> > the front pinion is adjusted properly, you loose only 0.3 degrees of
> > caster angle for the 2" lift compared to the factory caster setting.
>
> > Now I speak all this from personal experience on the exact same vehicle
> > as
> > the O.P., as I have installed the same lift on my TJ and setting the
> > pinion angles was what made it to ride smooth like stock again.
>
> > About adding cargo and upsetting the rear driveline angle to create
> > vibes,
> > this is what happens in the TJ.
> > There is a range that the pinion angle may be off, which doesn't create
> > noticeable vibes. The rear pinion is set to the upper side of this
> > range.
> > When you load the TJ and the suspension its lower, the rear pinion will
> > operate to the lower side of the range, and you won't get any vibes.
> > With
> > slight load, the pinion angle is at the center of the range and it feels
> > like running a bit smoother. But if you remove the hardtop and the rear
> > seat, which makes the suspension sit higher, you will notice driveline
> > vibes.
>
> > Bill Spiliotopoulos,
> > '96 XJ,
> > '06 TJ.
>
> > ? "Mike Romain" <roma...@sympatico.ca> ?????? ??? ??????
> >news:46cedfd9$0$5203$9a6e19ea@unlimited.newshosti ng.com...
> >> What 'are' you talking about?
>
> >> The front has a double cardan or CV joint already so needs 'no
> >> tweaking'
> >> at all even for a larger lift and a 2" is not going to change the rear
> >> enough to matter.
>
> >> You get that much/more change with a load on or off.
>
> >> By your reckoning if I put 4 people and gear in my Jeep, it won't drive
> >> because my height will be off by at least 2".
>
> >> Mike
> >> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> >> 88 Cherokee 235 BFG AT's - Gone to the rust pile...
> >> Canadian Off Road Trips Photos: Non members can still view!
> >> Jan/06http://www.imagestation.com/album/pictures.html?id=2115147590
> >> (More Off Road album links at bottom of the view page)
>
> >> Bill Spiliotopoulos wrote:
> >>>> 2.) With the 2" spacer lift, would I have to drop the t-case or do
> >>>> any other mods besides slapping it on?
>
> >>> Yes.
>
> >>> You have to turn the rear axle forward, so that the pinion axis is
> >>> almost parallel (a bit lower) to the transfer case output shaft. Or
> >>> drop the transfer case 1/2 inch. Turning the rear axle forward will
> >>> cost
> >>> more if you have a shop do it for you (requires either adjustable
> >>> lower
> >>> arms, or elongating the upper arms rear mounting holes and installing
> >>> an
> >>> eccentric washer to set the pinion angle). You may not be sensitive
> >>> enough to feel the vibes, but even with 1 inch lift, the pinion angle
> >>> gets misaligned, increasing mechanical noise and u-joint wear.
>
> >>> You also MUST rotate the front axle towards the rear to make the
> >>> pinion
> >>> axis parallel with the front driveshaft.
> >>> This will restore the caster angle to factory specification, which is
> >>> very important to limit the occurence of death wobble. The toe-in on
> >>> the front axle must be set after the pinion angle is set for the front
> >>> axle.
>
> >>> The 2" spacer lift and 31" M/T tire combination is a very good
> >>> combination. If you disconnect the front sway-bar the off-road
> >>> capability of your rig will be dramatically increased compared to what
> >>> it is right now. With the say-bar connected, your on-road behavior
> >>> will
> >>> not be much affected.
> >>> This is a picture of a 2006 TJ with 2" spacer lift and 235R15 tires
> >>> with
> >>> the swaay-bar disconnected.
> >>>http://alma-tech.com/tmp/tj_flex.jpg
>
> >>> But you must find a shop that is willing to deal with all the "minor"
> >>> details required to make the car run comfortable and safe as it was
> >>> prior to the lift (fine tune the pinion angles).
>
> >>> Bill Spiliotopoulos,
> >>> '96 XJ
> >>> '06 TJ.- Hide quoted text -
>
> - Show quoted text -
>
>So what you're saying is this:
>
>I get a 2.25 inch spacer lift with new shocks
>
>When I do get this lift setup, I will have to do two things: a.) drop
>the transfer case 1/2 inch, and b.) readjust the FRONT pinion angle
>which in turn readjusts the caster angle.
>
>Will I have to adjust the REAR trackbar as well with a trackbar
>relocation bracket?
>
>THANKS
Hi Tracie,
1)
2.25" inch spacers should be used if you remove the existing 0.25 factory
installed spacers/isolators in the TJ.
More than 2" spacer lift is not recomended.
If you get the 2" spacers, you must use them together with the factory 0.25
spacers to achieve the 2" lift.
2)
I have dropped the transfer case about 1/2 inch, but I have the D44 rear,
which has a shorter driveshaft and the pinion angle is affected more by the
lift, than a D35.
On the 2006 TJ model, if you have ABS, you have the D44. Otherwise you have
the D35.
I would recomend to you to drop the transfer case by gradually stacking wide
washers between the frame and skid
plate, until the engine doesn't feel rough when accelerating uphill in 1st
or 2nd gear. You will need to replace the 6 transfer case bolts with longer
ones. Start with 4 washers 2mm thick, and add up to 6 or 7. Use the widest
washers you can get (at least 1" diameter).
Bill Spiliotopoulos,
'96 XJ
'06 TJ.
#253
Guest
Posts: n/a
Re: RIM SIZE FOR 2006 WRANGLER X
? "Tracie" <brainart@upstate.edu> ?????? ??? ??????
news:1188219739.873279.122920@r34g2000hsd.googlegr oups.com...
On Aug 27, 8:25 am, "Bill Spiliotopoulos" <vsp...@yahoo.com> wrote:
> A correction,
> Caster angles should be positive (7 degrees), not negative.
>
> Ï "Bill Spiliotopoulos" <vsp...@yahoo.com> Ýãñáøå óôï
> ìÞíõìánews:faudc7$e95$1@ulysses.noc.ntua.gr...
>
>
>
> >I have to remind you that the TJ has a coil sprung suspension with upper
> >and lower arms, which alter the pinion angle when it is raised - lowered,
> >unlike the leaf sprung suspensions which keep the pinion angle constant.
>
> > Raising 2" does create driveline vibes because the rear pinion is no
> > longer parallel to the transfer case output shaft.
> > You can chose to ignore them or may not notice they are there, but the
> > truth is that they exist.
> > I have seen TJ of friends of mine that said they didn't have any
> > driveline
> > vibes after a 2" lift, but when I drove their rig I could feel the
> > difference. With a mismatch in pinion - output shaft angle, it feels
> > like
> > the engine is running rough and they blame the engine or the exhaust.
> > The
> > only way to convince them was to drop their thansfer case 1/2 inch and
> > ask
> > them if they cound feel the difference, which they could.
>
> > Yes, the TJ has a double cardan joint in the transfer case front end,
> > which requires the pinion angle to be set almost parallel to the
> > driveshaft (0.5 degrees lower). You won't notice driveline vibes when in
> > 2wd mode though. But the front pinion angle also affects the front
> > caster
> > angle.
> > By raising 2" in the TJ, the caster increases from -7 degrees to
> > about -5.
> > The front pinion also gets 2 degrees higher than the driveshaft. By
> > re-adjusting the front pinion angle, you fix the caster angle also. When
> > the front pinion is adjusted properly, you loose only 0.3 degrees of
> > caster angle for the 2" lift compared to the factory caster setting.
>
> > Now I speak all this from personal experience on the exact same vehicle
> > as
> > the O.P., as I have installed the same lift on my TJ and setting the
> > pinion angles was what made it to ride smooth like stock again.
>
> > About adding cargo and upsetting the rear driveline angle to create
> > vibes,
> > this is what happens in the TJ.
> > There is a range that the pinion angle may be off, which doesn't create
> > noticeable vibes. The rear pinion is set to the upper side of this
> > range.
> > When you load the TJ and the suspension its lower, the rear pinion will
> > operate to the lower side of the range, and you won't get any vibes.
> > With
> > slight load, the pinion angle is at the center of the range and it feels
> > like running a bit smoother. But if you remove the hardtop and the rear
> > seat, which makes the suspension sit higher, you will notice driveline
> > vibes.
>
> > Bill Spiliotopoulos,
> > '96 XJ,
> > '06 TJ.
>
> > ? "Mike Romain" <roma...@sympatico.ca> ?????? ??? ??????
> >news:46cedfd9$0$5203$9a6e19ea@unlimited.newshosti ng.com...
> >> What 'are' you talking about?
>
> >> The front has a double cardan or CV joint already so needs 'no
> >> tweaking'
> >> at all even for a larger lift and a 2" is not going to change the rear
> >> enough to matter.
>
> >> You get that much/more change with a load on or off.
>
> >> By your reckoning if I put 4 people and gear in my Jeep, it won't drive
> >> because my height will be off by at least 2".
>
> >> Mike
> >> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> >> 88 Cherokee 235 BFG AT's - Gone to the rust pile...
> >> Canadian Off Road Trips Photos: Non members can still view!
> >> Jan/06http://www.imagestation.com/album/pictures.html?id=2115147590
> >> (More Off Road album links at bottom of the view page)
>
> >> Bill Spiliotopoulos wrote:
> >>>> 2.) With the 2" spacer lift, would I have to drop the t-case or do
> >>>> any other mods besides slapping it on?
>
> >>> Yes.
>
> >>> You have to turn the rear axle forward, so that the pinion axis is
> >>> almost parallel (a bit lower) to the transfer case output shaft. Or
> >>> drop the transfer case 1/2 inch. Turning the rear axle forward will
> >>> cost
> >>> more if you have a shop do it for you (requires either adjustable
> >>> lower
> >>> arms, or elongating the upper arms rear mounting holes and installing
> >>> an
> >>> eccentric washer to set the pinion angle). You may not be sensitive
> >>> enough to feel the vibes, but even with 1 inch lift, the pinion angle
> >>> gets misaligned, increasing mechanical noise and u-joint wear.
>
> >>> You also MUST rotate the front axle towards the rear to make the
> >>> pinion
> >>> axis parallel with the front driveshaft.
> >>> This will restore the caster angle to factory specification, which is
> >>> very important to limit the occurence of death wobble. The toe-in on
> >>> the front axle must be set after the pinion angle is set for the front
> >>> axle.
>
> >>> The 2" spacer lift and 31" M/T tire combination is a very good
> >>> combination. If you disconnect the front sway-bar the off-road
> >>> capability of your rig will be dramatically increased compared to what
> >>> it is right now. With the say-bar connected, your on-road behavior
> >>> will
> >>> not be much affected.
> >>> This is a picture of a 2006 TJ with 2" spacer lift and 235R15 tires
> >>> with
> >>> the swaay-bar disconnected.
> >>>http://alma-tech.com/tmp/tj_flex.jpg
>
> >>> But you must find a shop that is willing to deal with all the "minor"
> >>> details required to make the car run comfortable and safe as it was
> >>> prior to the lift (fine tune the pinion angles).
>
> >>> Bill Spiliotopoulos,
> >>> '96 XJ
> >>> '06 TJ.- Hide quoted text -
>
> - Show quoted text -
>
>So what you're saying is this:
>
>I get a 2.25 inch spacer lift with new shocks
>
>When I do get this lift setup, I will have to do two things: a.) drop
>the transfer case 1/2 inch, and b.) readjust the FRONT pinion angle
>which in turn readjusts the caster angle.
>
>Will I have to adjust the REAR trackbar as well with a trackbar
>relocation bracket?
>
>THANKS
Hi Tracie,
1)
2.25" inch spacers should be used if you remove the existing 0.25 factory
installed spacers/isolators in the TJ.
More than 2" spacer lift is not recomended.
If you get the 2" spacers, you must use them together with the factory 0.25
spacers to achieve the 2" lift.
2)
I have dropped the transfer case about 1/2 inch, but I have the D44 rear,
which has a shorter driveshaft and the pinion angle is affected more by the
lift, than a D35.
On the 2006 TJ model, if you have ABS, you have the D44. Otherwise you have
the D35.
I would recomend to you to drop the transfer case by gradually stacking wide
washers between the frame and skid
plate, until the engine doesn't feel rough when accelerating uphill in 1st
or 2nd gear. You will need to replace the 6 transfer case bolts with longer
ones. Start with 4 washers 2mm thick, and add up to 6 or 7. Use the widest
washers you can get (at least 1" diameter).
Bill Spiliotopoulos,
'96 XJ
'06 TJ.
#254
Guest
Posts: n/a
Re: RIM SIZE FOR 2006 WRANGLER X
Tracie wrote:
> And TW....
>
> You stated that with a 2" inch suspension lift you do NOT need to
> relocate the front or rear track bar. Same question....does the 2.25"
> spacer vs. the 2" spacer change that?
The factory designs the suspension to center the axles under the
body/chassis. When you start lifting the chassis, the axles become
un-centered in relation. The more you lift, the more this occurs. While
it is always best to have everything to factory spec, with 2 or 2.25"
pucks, the axles have not moved a great deal so you can get away without
relocating them to center. Just know that they will be off slightly.
tw
> And TW....
>
> You stated that with a 2" inch suspension lift you do NOT need to
> relocate the front or rear track bar. Same question....does the 2.25"
> spacer vs. the 2" spacer change that?
The factory designs the suspension to center the axles under the
body/chassis. When you start lifting the chassis, the axles become
un-centered in relation. The more you lift, the more this occurs. While
it is always best to have everything to factory spec, with 2 or 2.25"
pucks, the axles have not moved a great deal so you can get away without
relocating them to center. Just know that they will be off slightly.
tw
#255
Guest
Posts: n/a
Re: RIM SIZE FOR 2006 WRANGLER X
Tracie wrote:
> And TW....
>
> You stated that with a 2" inch suspension lift you do NOT need to
> relocate the front or rear track bar. Same question....does the 2.25"
> spacer vs. the 2" spacer change that?
The factory designs the suspension to center the axles under the
body/chassis. When you start lifting the chassis, the axles become
un-centered in relation. The more you lift, the more this occurs. While
it is always best to have everything to factory spec, with 2 or 2.25"
pucks, the axles have not moved a great deal so you can get away without
relocating them to center. Just know that they will be off slightly.
tw
> And TW....
>
> You stated that with a 2" inch suspension lift you do NOT need to
> relocate the front or rear track bar. Same question....does the 2.25"
> spacer vs. the 2" spacer change that?
The factory designs the suspension to center the axles under the
body/chassis. When you start lifting the chassis, the axles become
un-centered in relation. The more you lift, the more this occurs. While
it is always best to have everything to factory spec, with 2 or 2.25"
pucks, the axles have not moved a great deal so you can get away without
relocating them to center. Just know that they will be off slightly.
tw
#256
Guest
Posts: n/a
Re: RIM SIZE FOR 2006 WRANGLER X
Tracie wrote:
> And TW....
>
> You stated that with a 2" inch suspension lift you do NOT need to
> relocate the front or rear track bar. Same question....does the 2.25"
> spacer vs. the 2" spacer change that?
The factory designs the suspension to center the axles under the
body/chassis. When you start lifting the chassis, the axles become
un-centered in relation. The more you lift, the more this occurs. While
it is always best to have everything to factory spec, with 2 or 2.25"
pucks, the axles have not moved a great deal so you can get away without
relocating them to center. Just know that they will be off slightly.
tw
> And TW....
>
> You stated that with a 2" inch suspension lift you do NOT need to
> relocate the front or rear track bar. Same question....does the 2.25"
> spacer vs. the 2" spacer change that?
The factory designs the suspension to center the axles under the
body/chassis. When you start lifting the chassis, the axles become
un-centered in relation. The more you lift, the more this occurs. While
it is always best to have everything to factory spec, with 2 or 2.25"
pucks, the axles have not moved a great deal so you can get away without
relocating them to center. Just know that they will be off slightly.
tw
#257
Guest
Posts: n/a
Re: RIM SIZE FOR 2006 WRANGLER X
Tracie wrote:
> And TW....
>
> You stated that with a 2" inch suspension lift you do NOT need to
> relocate the front or rear track bar. Same question....does the 2.25"
> spacer vs. the 2" spacer change that?
The factory designs the suspension to center the axles under the
body/chassis. When you start lifting the chassis, the axles become
un-centered in relation. The more you lift, the more this occurs. While
it is always best to have everything to factory spec, with 2 or 2.25"
pucks, the axles have not moved a great deal so you can get away without
relocating them to center. Just know that they will be off slightly.
tw
> And TW....
>
> You stated that with a 2" inch suspension lift you do NOT need to
> relocate the front or rear track bar. Same question....does the 2.25"
> spacer vs. the 2" spacer change that?
The factory designs the suspension to center the axles under the
body/chassis. When you start lifting the chassis, the axles become
un-centered in relation. The more you lift, the more this occurs. While
it is always best to have everything to factory spec, with 2 or 2.25"
pucks, the axles have not moved a great deal so you can get away without
relocating them to center. Just know that they will be off slightly.
tw
#258
Guest
Posts: n/a
Re: RIM SIZE FOR 2006 WRANGLER X
? "Tracie" <brainart@upstate.edu> ?????? ??? ??????
news:1187964373.341817.151440@i13g2000prf.googlegr oups.com...
> On Aug 24, 9:42 am, Mike Romain <roma...@sympatico.ca> wrote:
>> What 'are' you talking about?
>>
>> The front has a double cardan or CV joint already so needs 'no tweaking'
>> at all even for a larger lift and a 2" is not going to change the rear
>> enough to matter.
>>
>> You get that much/more change with a load on or off.
>>
>> By your reckoning if I put 4 people and gear in my Jeep, it won't drive
>> because my height will be off by at least 2".
>>
>> Mike
>> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
>> 88 Cherokee 235 BFG AT's - Gone to the rust pile...
>> Canadian Off Road Trips Photos: Non members can still view!
>> Jan/06http://www.imagestation.com/album/pictures.html?id=2115147590
>> (More Off Road album links at bottom of the view page)
>>
>>
>>
>> Bill Spiliotopoulos wrote:
>> >> 2.) With the 2" spacer lift, would I have to drop the t-case or do
>> >> any other mods besides slapping it on?
>>
>> > Yes.
>>
>> > You have to turn the rear axle forward, so that the pinion axis is
>> > almost
>> > parallel (a bit lower) to the transfer case output shaft. Or drop the
>> > transfer case 1/2 inch. Turning the rear axle forward will cost more if
>> > you
>> > have a shop do it for you (requires either adjustable lower arms, or
>> > elongating the upper arms rear mounting holes and installing an
>> > eccentric
>> > washer to set the pinion angle). You may not be sensitive enough to
>> > feel the
>> > vibes, but even with 1 inch lift, the pinion angle gets misaligned,
>> > increasing mechanical noise and u-joint wear.
>>
>> > You also MUST rotate the front axle towards the rear to make the pinion
>> > axis
>> > parallel with the front driveshaft.
>> > This will restore the caster angle to factory specification, which is
>> > very
>> > important to limit the occurence of death wobble. The toe-in on the
>> > front
>> > axle must be set after the pinion angle is set for the front axle.
>>
>> > The 2" spacer lift and 31" M/T tire combination is a very good
>> > combination.
>> > If you disconnect the front sway-bar the off-road capability of your
>> > rig
>> > will be dramatically increased compared to what it is right now. With
>> > the
>> > say-bar connected, your on-road behavior will not be much affected.
>> > This is a picture of a 2006 TJ with 2" spacer lift and 235R15 tires
>> > with the
>> > swaay-bar disconnected.
>> >http://alma-tech.com/tmp/tj_flex.jpg
>>
>> > But you must find a shop that is willing to deal with all the "minor"
>> > details required to make the car run comfortable and safe as it was
>> > prior to
>> > the lift (fine tune the pinion angles).
>>
>> > Bill Spiliotopoulos,
>> > '96 XJ
>> > '06 TJ.- Hide quoted text -
>>
>> - Show quoted text -
>
> Yippee!! I got my BF Goodrich Mud Terrains today! I will be getting
> them installed this weekend. They are the 31 X 10.5 X 15. They are
> AWESOME looking!
>
> I just have a question. I will be getting a 2.25" coil spacer lift
> with new shocks sometime in the near future. I just wanted to get the
> new tires and get them put on first before I did the lift. Do I need
> an alignment with new tires, or should I wait until I get the lift
> done to get the alignment?
>
> THANKS
>
news:1187964373.341817.151440@i13g2000prf.googlegr oups.com...
> On Aug 24, 9:42 am, Mike Romain <roma...@sympatico.ca> wrote:
>> What 'are' you talking about?
>>
>> The front has a double cardan or CV joint already so needs 'no tweaking'
>> at all even for a larger lift and a 2" is not going to change the rear
>> enough to matter.
>>
>> You get that much/more change with a load on or off.
>>
>> By your reckoning if I put 4 people and gear in my Jeep, it won't drive
>> because my height will be off by at least 2".
>>
>> Mike
>> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
>> 88 Cherokee 235 BFG AT's - Gone to the rust pile...
>> Canadian Off Road Trips Photos: Non members can still view!
>> Jan/06http://www.imagestation.com/album/pictures.html?id=2115147590
>> (More Off Road album links at bottom of the view page)
>>
>>
>>
>> Bill Spiliotopoulos wrote:
>> >> 2.) With the 2" spacer lift, would I have to drop the t-case or do
>> >> any other mods besides slapping it on?
>>
>> > Yes.
>>
>> > You have to turn the rear axle forward, so that the pinion axis is
>> > almost
>> > parallel (a bit lower) to the transfer case output shaft. Or drop the
>> > transfer case 1/2 inch. Turning the rear axle forward will cost more if
>> > you
>> > have a shop do it for you (requires either adjustable lower arms, or
>> > elongating the upper arms rear mounting holes and installing an
>> > eccentric
>> > washer to set the pinion angle). You may not be sensitive enough to
>> > feel the
>> > vibes, but even with 1 inch lift, the pinion angle gets misaligned,
>> > increasing mechanical noise and u-joint wear.
>>
>> > You also MUST rotate the front axle towards the rear to make the pinion
>> > axis
>> > parallel with the front driveshaft.
>> > This will restore the caster angle to factory specification, which is
>> > very
>> > important to limit the occurence of death wobble. The toe-in on the
>> > front
>> > axle must be set after the pinion angle is set for the front axle.
>>
>> > The 2" spacer lift and 31" M/T tire combination is a very good
>> > combination.
>> > If you disconnect the front sway-bar the off-road capability of your
>> > rig
>> > will be dramatically increased compared to what it is right now. With
>> > the
>> > say-bar connected, your on-road behavior will not be much affected.
>> > This is a picture of a 2006 TJ with 2" spacer lift and 235R15 tires
>> > with the
>> > swaay-bar disconnected.
>> >http://alma-tech.com/tmp/tj_flex.jpg
>>
>> > But you must find a shop that is willing to deal with all the "minor"
>> > details required to make the car run comfortable and safe as it was
>> > prior to
>> > the lift (fine tune the pinion angles).
>>
>> > Bill Spiliotopoulos,
>> > '96 XJ
>> > '06 TJ.- Hide quoted text -
>>
>> - Show quoted text -
>
> Yippee!! I got my BF Goodrich Mud Terrains today! I will be getting
> them installed this weekend. They are the 31 X 10.5 X 15. They are
> AWESOME looking!
>
> I just have a question. I will be getting a 2.25" coil spacer lift
> with new shocks sometime in the near future. I just wanted to get the
> new tires and get them put on first before I did the lift. Do I need
> an alignment with new tires, or should I wait until I get the lift
> done to get the alignment?
>
> THANKS
>
#259
Guest
Posts: n/a
Re: RIM SIZE FOR 2006 WRANGLER X
? "Tracie" <brainart@upstate.edu> ?????? ??? ??????
news:1187964373.341817.151440@i13g2000prf.googlegr oups.com...
> On Aug 24, 9:42 am, Mike Romain <roma...@sympatico.ca> wrote:
>> What 'are' you talking about?
>>
>> The front has a double cardan or CV joint already so needs 'no tweaking'
>> at all even for a larger lift and a 2" is not going to change the rear
>> enough to matter.
>>
>> You get that much/more change with a load on or off.
>>
>> By your reckoning if I put 4 people and gear in my Jeep, it won't drive
>> because my height will be off by at least 2".
>>
>> Mike
>> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
>> 88 Cherokee 235 BFG AT's - Gone to the rust pile...
>> Canadian Off Road Trips Photos: Non members can still view!
>> Jan/06http://www.imagestation.com/album/pictures.html?id=2115147590
>> (More Off Road album links at bottom of the view page)
>>
>>
>>
>> Bill Spiliotopoulos wrote:
>> >> 2.) With the 2" spacer lift, would I have to drop the t-case or do
>> >> any other mods besides slapping it on?
>>
>> > Yes.
>>
>> > You have to turn the rear axle forward, so that the pinion axis is
>> > almost
>> > parallel (a bit lower) to the transfer case output shaft. Or drop the
>> > transfer case 1/2 inch. Turning the rear axle forward will cost more if
>> > you
>> > have a shop do it for you (requires either adjustable lower arms, or
>> > elongating the upper arms rear mounting holes and installing an
>> > eccentric
>> > washer to set the pinion angle). You may not be sensitive enough to
>> > feel the
>> > vibes, but even with 1 inch lift, the pinion angle gets misaligned,
>> > increasing mechanical noise and u-joint wear.
>>
>> > You also MUST rotate the front axle towards the rear to make the pinion
>> > axis
>> > parallel with the front driveshaft.
>> > This will restore the caster angle to factory specification, which is
>> > very
>> > important to limit the occurence of death wobble. The toe-in on the
>> > front
>> > axle must be set after the pinion angle is set for the front axle.
>>
>> > The 2" spacer lift and 31" M/T tire combination is a very good
>> > combination.
>> > If you disconnect the front sway-bar the off-road capability of your
>> > rig
>> > will be dramatically increased compared to what it is right now. With
>> > the
>> > say-bar connected, your on-road behavior will not be much affected.
>> > This is a picture of a 2006 TJ with 2" spacer lift and 235R15 tires
>> > with the
>> > swaay-bar disconnected.
>> >http://alma-tech.com/tmp/tj_flex.jpg
>>
>> > But you must find a shop that is willing to deal with all the "minor"
>> > details required to make the car run comfortable and safe as it was
>> > prior to
>> > the lift (fine tune the pinion angles).
>>
>> > Bill Spiliotopoulos,
>> > '96 XJ
>> > '06 TJ.- Hide quoted text -
>>
>> - Show quoted text -
>
> Yippee!! I got my BF Goodrich Mud Terrains today! I will be getting
> them installed this weekend. They are the 31 X 10.5 X 15. They are
> AWESOME looking!
>
> I just have a question. I will be getting a 2.25" coil spacer lift
> with new shocks sometime in the near future. I just wanted to get the
> new tires and get them put on first before I did the lift. Do I need
> an alignment with new tires, or should I wait until I get the lift
> done to get the alignment?
>
> THANKS
>
news:1187964373.341817.151440@i13g2000prf.googlegr oups.com...
> On Aug 24, 9:42 am, Mike Romain <roma...@sympatico.ca> wrote:
>> What 'are' you talking about?
>>
>> The front has a double cardan or CV joint already so needs 'no tweaking'
>> at all even for a larger lift and a 2" is not going to change the rear
>> enough to matter.
>>
>> You get that much/more change with a load on or off.
>>
>> By your reckoning if I put 4 people and gear in my Jeep, it won't drive
>> because my height will be off by at least 2".
>>
>> Mike
>> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
>> 88 Cherokee 235 BFG AT's - Gone to the rust pile...
>> Canadian Off Road Trips Photos: Non members can still view!
>> Jan/06http://www.imagestation.com/album/pictures.html?id=2115147590
>> (More Off Road album links at bottom of the view page)
>>
>>
>>
>> Bill Spiliotopoulos wrote:
>> >> 2.) With the 2" spacer lift, would I have to drop the t-case or do
>> >> any other mods besides slapping it on?
>>
>> > Yes.
>>
>> > You have to turn the rear axle forward, so that the pinion axis is
>> > almost
>> > parallel (a bit lower) to the transfer case output shaft. Or drop the
>> > transfer case 1/2 inch. Turning the rear axle forward will cost more if
>> > you
>> > have a shop do it for you (requires either adjustable lower arms, or
>> > elongating the upper arms rear mounting holes and installing an
>> > eccentric
>> > washer to set the pinion angle). You may not be sensitive enough to
>> > feel the
>> > vibes, but even with 1 inch lift, the pinion angle gets misaligned,
>> > increasing mechanical noise and u-joint wear.
>>
>> > You also MUST rotate the front axle towards the rear to make the pinion
>> > axis
>> > parallel with the front driveshaft.
>> > This will restore the caster angle to factory specification, which is
>> > very
>> > important to limit the occurence of death wobble. The toe-in on the
>> > front
>> > axle must be set after the pinion angle is set for the front axle.
>>
>> > The 2" spacer lift and 31" M/T tire combination is a very good
>> > combination.
>> > If you disconnect the front sway-bar the off-road capability of your
>> > rig
>> > will be dramatically increased compared to what it is right now. With
>> > the
>> > say-bar connected, your on-road behavior will not be much affected.
>> > This is a picture of a 2006 TJ with 2" spacer lift and 235R15 tires
>> > with the
>> > swaay-bar disconnected.
>> >http://alma-tech.com/tmp/tj_flex.jpg
>>
>> > But you must find a shop that is willing to deal with all the "minor"
>> > details required to make the car run comfortable and safe as it was
>> > prior to
>> > the lift (fine tune the pinion angles).
>>
>> > Bill Spiliotopoulos,
>> > '96 XJ
>> > '06 TJ.- Hide quoted text -
>>
>> - Show quoted text -
>
> Yippee!! I got my BF Goodrich Mud Terrains today! I will be getting
> them installed this weekend. They are the 31 X 10.5 X 15. They are
> AWESOME looking!
>
> I just have a question. I will be getting a 2.25" coil spacer lift
> with new shocks sometime in the near future. I just wanted to get the
> new tires and get them put on first before I did the lift. Do I need
> an alignment with new tires, or should I wait until I get the lift
> done to get the alignment?
>
> THANKS
>
#260
Guest
Posts: n/a
Re: RIM SIZE FOR 2006 WRANGLER X
? "Tracie" <brainart@upstate.edu> ?????? ??? ??????
news:1187964373.341817.151440@i13g2000prf.googlegr oups.com...
> On Aug 24, 9:42 am, Mike Romain <roma...@sympatico.ca> wrote:
>> What 'are' you talking about?
>>
>> The front has a double cardan or CV joint already so needs 'no tweaking'
>> at all even for a larger lift and a 2" is not going to change the rear
>> enough to matter.
>>
>> You get that much/more change with a load on or off.
>>
>> By your reckoning if I put 4 people and gear in my Jeep, it won't drive
>> because my height will be off by at least 2".
>>
>> Mike
>> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
>> 88 Cherokee 235 BFG AT's - Gone to the rust pile...
>> Canadian Off Road Trips Photos: Non members can still view!
>> Jan/06http://www.imagestation.com/album/pictures.html?id=2115147590
>> (More Off Road album links at bottom of the view page)
>>
>>
>>
>> Bill Spiliotopoulos wrote:
>> >> 2.) With the 2" spacer lift, would I have to drop the t-case or do
>> >> any other mods besides slapping it on?
>>
>> > Yes.
>>
>> > You have to turn the rear axle forward, so that the pinion axis is
>> > almost
>> > parallel (a bit lower) to the transfer case output shaft. Or drop the
>> > transfer case 1/2 inch. Turning the rear axle forward will cost more if
>> > you
>> > have a shop do it for you (requires either adjustable lower arms, or
>> > elongating the upper arms rear mounting holes and installing an
>> > eccentric
>> > washer to set the pinion angle). You may not be sensitive enough to
>> > feel the
>> > vibes, but even with 1 inch lift, the pinion angle gets misaligned,
>> > increasing mechanical noise and u-joint wear.
>>
>> > You also MUST rotate the front axle towards the rear to make the pinion
>> > axis
>> > parallel with the front driveshaft.
>> > This will restore the caster angle to factory specification, which is
>> > very
>> > important to limit the occurence of death wobble. The toe-in on the
>> > front
>> > axle must be set after the pinion angle is set for the front axle.
>>
>> > The 2" spacer lift and 31" M/T tire combination is a very good
>> > combination.
>> > If you disconnect the front sway-bar the off-road capability of your
>> > rig
>> > will be dramatically increased compared to what it is right now. With
>> > the
>> > say-bar connected, your on-road behavior will not be much affected.
>> > This is a picture of a 2006 TJ with 2" spacer lift and 235R15 tires
>> > with the
>> > swaay-bar disconnected.
>> >http://alma-tech.com/tmp/tj_flex.jpg
>>
>> > But you must find a shop that is willing to deal with all the "minor"
>> > details required to make the car run comfortable and safe as it was
>> > prior to
>> > the lift (fine tune the pinion angles).
>>
>> > Bill Spiliotopoulos,
>> > '96 XJ
>> > '06 TJ.- Hide quoted text -
>>
>> - Show quoted text -
>
> Yippee!! I got my BF Goodrich Mud Terrains today! I will be getting
> them installed this weekend. They are the 31 X 10.5 X 15. They are
> AWESOME looking!
>
> I just have a question. I will be getting a 2.25" coil spacer lift
> with new shocks sometime in the near future. I just wanted to get the
> new tires and get them put on first before I did the lift. Do I need
> an alignment with new tires, or should I wait until I get the lift
> done to get the alignment?
>
> THANKS
>
news:1187964373.341817.151440@i13g2000prf.googlegr oups.com...
> On Aug 24, 9:42 am, Mike Romain <roma...@sympatico.ca> wrote:
>> What 'are' you talking about?
>>
>> The front has a double cardan or CV joint already so needs 'no tweaking'
>> at all even for a larger lift and a 2" is not going to change the rear
>> enough to matter.
>>
>> You get that much/more change with a load on or off.
>>
>> By your reckoning if I put 4 people and gear in my Jeep, it won't drive
>> because my height will be off by at least 2".
>>
>> Mike
>> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
>> 88 Cherokee 235 BFG AT's - Gone to the rust pile...
>> Canadian Off Road Trips Photos: Non members can still view!
>> Jan/06http://www.imagestation.com/album/pictures.html?id=2115147590
>> (More Off Road album links at bottom of the view page)
>>
>>
>>
>> Bill Spiliotopoulos wrote:
>> >> 2.) With the 2" spacer lift, would I have to drop the t-case or do
>> >> any other mods besides slapping it on?
>>
>> > Yes.
>>
>> > You have to turn the rear axle forward, so that the pinion axis is
>> > almost
>> > parallel (a bit lower) to the transfer case output shaft. Or drop the
>> > transfer case 1/2 inch. Turning the rear axle forward will cost more if
>> > you
>> > have a shop do it for you (requires either adjustable lower arms, or
>> > elongating the upper arms rear mounting holes and installing an
>> > eccentric
>> > washer to set the pinion angle). You may not be sensitive enough to
>> > feel the
>> > vibes, but even with 1 inch lift, the pinion angle gets misaligned,
>> > increasing mechanical noise and u-joint wear.
>>
>> > You also MUST rotate the front axle towards the rear to make the pinion
>> > axis
>> > parallel with the front driveshaft.
>> > This will restore the caster angle to factory specification, which is
>> > very
>> > important to limit the occurence of death wobble. The toe-in on the
>> > front
>> > axle must be set after the pinion angle is set for the front axle.
>>
>> > The 2" spacer lift and 31" M/T tire combination is a very good
>> > combination.
>> > If you disconnect the front sway-bar the off-road capability of your
>> > rig
>> > will be dramatically increased compared to what it is right now. With
>> > the
>> > say-bar connected, your on-road behavior will not be much affected.
>> > This is a picture of a 2006 TJ with 2" spacer lift and 235R15 tires
>> > with the
>> > swaay-bar disconnected.
>> >http://alma-tech.com/tmp/tj_flex.jpg
>>
>> > But you must find a shop that is willing to deal with all the "minor"
>> > details required to make the car run comfortable and safe as it was
>> > prior to
>> > the lift (fine tune the pinion angles).
>>
>> > Bill Spiliotopoulos,
>> > '96 XJ
>> > '06 TJ.- Hide quoted text -
>>
>> - Show quoted text -
>
> Yippee!! I got my BF Goodrich Mud Terrains today! I will be getting
> them installed this weekend. They are the 31 X 10.5 X 15. They are
> AWESOME looking!
>
> I just have a question. I will be getting a 2.25" coil spacer lift
> with new shocks sometime in the near future. I just wanted to get the
> new tires and get them put on first before I did the lift. Do I need
> an alignment with new tires, or should I wait until I get the lift
> done to get the alignment?
>
> THANKS
>