MTBE to Ethanol additive change-over ..PROBLEMS
#41
Guest
Posts: n/a
Re: MTBE to Ethanol additive change-over ..PROBLEMS
> > and leaking, harmful destructive deposits formed inside engines, etc.
> > About half the USA states have already banned MTBE additive and are
> > rapidly changing over to an ethanol additive, the ethanol is quite
> > incompatible with most of the fiberglass resin used in fuel tanks. The
> > decomposition products of the 'melting/dissolving' resin doesnt burn
> > and will form vast and destructive deposits in the engine (similar to
> > putting sugar into the gasoline).
> >
> > for more info:
> > http://www.moyermarine.com/forums/at...ttachmentid=42
> > or BOATUS.com website.
I had a pisser of a time with my 90HP Honda 4 stroke outboard this past
spring. Clogged passageways, rough running, crapped up lines etc. Cost me
over $500 to have repaired, and it had to be done a second time!!(No cost)
My mechanic (Chris) was quoted in the Boat US article and I guess the
problem comes about when the two gasolines are mixed together. Forms a
sludge and just makes a royal mess!
Also, had to replace a gas tank on my two month old weed whacker because the
fuel dissolved the seam of the plastic gas tank. It looks as if it just
melted the glue(?) bedcause it ran down the outside of the tank. Looked
like hardened epoxy.
It was not a very pretty Spring. Got into boating about 3 months late. A
lot of fellows in the boat club had similiar troubles.
Hope for better this year.
Kevin
> > About half the USA states have already banned MTBE additive and are
> > rapidly changing over to an ethanol additive, the ethanol is quite
> > incompatible with most of the fiberglass resin used in fuel tanks. The
> > decomposition products of the 'melting/dissolving' resin doesnt burn
> > and will form vast and destructive deposits in the engine (similar to
> > putting sugar into the gasoline).
> >
> > for more info:
> > http://www.moyermarine.com/forums/at...ttachmentid=42
> > or BOATUS.com website.
I had a pisser of a time with my 90HP Honda 4 stroke outboard this past
spring. Clogged passageways, rough running, crapped up lines etc. Cost me
over $500 to have repaired, and it had to be done a second time!!(No cost)
My mechanic (Chris) was quoted in the Boat US article and I guess the
problem comes about when the two gasolines are mixed together. Forms a
sludge and just makes a royal mess!
Also, had to replace a gas tank on my two month old weed whacker because the
fuel dissolved the seam of the plastic gas tank. It looks as if it just
melted the glue(?) bedcause it ran down the outside of the tank. Looked
like hardened epoxy.
It was not a very pretty Spring. Got into boating about 3 months late. A
lot of fellows in the boat club had similiar troubles.
Hope for better this year.
Kevin
#42
Guest
Posts: n/a
Re: MTBE to Ethanol additive change-over ..PROBLEMS
> > and leaking, harmful destructive deposits formed inside engines, etc.
> > About half the USA states have already banned MTBE additive and are
> > rapidly changing over to an ethanol additive, the ethanol is quite
> > incompatible with most of the fiberglass resin used in fuel tanks. The
> > decomposition products of the 'melting/dissolving' resin doesnt burn
> > and will form vast and destructive deposits in the engine (similar to
> > putting sugar into the gasoline).
> >
> > for more info:
> > http://www.moyermarine.com/forums/at...ttachmentid=42
> > or BOATUS.com website.
I had a pisser of a time with my 90HP Honda 4 stroke outboard this past
spring. Clogged passageways, rough running, crapped up lines etc. Cost me
over $500 to have repaired, and it had to be done a second time!!(No cost)
My mechanic (Chris) was quoted in the Boat US article and I guess the
problem comes about when the two gasolines are mixed together. Forms a
sludge and just makes a royal mess!
Also, had to replace a gas tank on my two month old weed whacker because the
fuel dissolved the seam of the plastic gas tank. It looks as if it just
melted the glue(?) bedcause it ran down the outside of the tank. Looked
like hardened epoxy.
It was not a very pretty Spring. Got into boating about 3 months late. A
lot of fellows in the boat club had similiar troubles.
Hope for better this year.
Kevin
> > About half the USA states have already banned MTBE additive and are
> > rapidly changing over to an ethanol additive, the ethanol is quite
> > incompatible with most of the fiberglass resin used in fuel tanks. The
> > decomposition products of the 'melting/dissolving' resin doesnt burn
> > and will form vast and destructive deposits in the engine (similar to
> > putting sugar into the gasoline).
> >
> > for more info:
> > http://www.moyermarine.com/forums/at...ttachmentid=42
> > or BOATUS.com website.
I had a pisser of a time with my 90HP Honda 4 stroke outboard this past
spring. Clogged passageways, rough running, crapped up lines etc. Cost me
over $500 to have repaired, and it had to be done a second time!!(No cost)
My mechanic (Chris) was quoted in the Boat US article and I guess the
problem comes about when the two gasolines are mixed together. Forms a
sludge and just makes a royal mess!
Also, had to replace a gas tank on my two month old weed whacker because the
fuel dissolved the seam of the plastic gas tank. It looks as if it just
melted the glue(?) bedcause it ran down the outside of the tank. Looked
like hardened epoxy.
It was not a very pretty Spring. Got into boating about 3 months late. A
lot of fellows in the boat club had similiar troubles.
Hope for better this year.
Kevin
#43
Guest
Posts: n/a
Re: MTBE to Ethanol additive change-over ..PROBLEMS
> > and leaking, harmful destructive deposits formed inside engines, etc.
> > About half the USA states have already banned MTBE additive and are
> > rapidly changing over to an ethanol additive, the ethanol is quite
> > incompatible with most of the fiberglass resin used in fuel tanks. The
> > decomposition products of the 'melting/dissolving' resin doesnt burn
> > and will form vast and destructive deposits in the engine (similar to
> > putting sugar into the gasoline).
> >
> > for more info:
> > http://www.moyermarine.com/forums/at...ttachmentid=42
> > or BOATUS.com website.
I had a pisser of a time with my 90HP Honda 4 stroke outboard this past
spring. Clogged passageways, rough running, crapped up lines etc. Cost me
over $500 to have repaired, and it had to be done a second time!!(No cost)
My mechanic (Chris) was quoted in the Boat US article and I guess the
problem comes about when the two gasolines are mixed together. Forms a
sludge and just makes a royal mess!
Also, had to replace a gas tank on my two month old weed whacker because the
fuel dissolved the seam of the plastic gas tank. It looks as if it just
melted the glue(?) bedcause it ran down the outside of the tank. Looked
like hardened epoxy.
It was not a very pretty Spring. Got into boating about 3 months late. A
lot of fellows in the boat club had similiar troubles.
Hope for better this year.
Kevin
> > About half the USA states have already banned MTBE additive and are
> > rapidly changing over to an ethanol additive, the ethanol is quite
> > incompatible with most of the fiberglass resin used in fuel tanks. The
> > decomposition products of the 'melting/dissolving' resin doesnt burn
> > and will form vast and destructive deposits in the engine (similar to
> > putting sugar into the gasoline).
> >
> > for more info:
> > http://www.moyermarine.com/forums/at...ttachmentid=42
> > or BOATUS.com website.
I had a pisser of a time with my 90HP Honda 4 stroke outboard this past
spring. Clogged passageways, rough running, crapped up lines etc. Cost me
over $500 to have repaired, and it had to be done a second time!!(No cost)
My mechanic (Chris) was quoted in the Boat US article and I guess the
problem comes about when the two gasolines are mixed together. Forms a
sludge and just makes a royal mess!
Also, had to replace a gas tank on my two month old weed whacker because the
fuel dissolved the seam of the plastic gas tank. It looks as if it just
melted the glue(?) bedcause it ran down the outside of the tank. Looked
like hardened epoxy.
It was not a very pretty Spring. Got into boating about 3 months late. A
lot of fellows in the boat club had similiar troubles.
Hope for better this year.
Kevin
#44
Guest
Posts: n/a
Re: MTBE to Ethanol additive change-over ..PROBLEMS
Kevin Gunther wrote:
[snip]
> I had a pisser of a time with my 90HP Honda 4 stroke outboard this past
> spring. Clogged passageways, rough running, crapped up lines etc. Cost me
> over $500 to have repaired, and it had to be done a second time!!(No cost)
> My mechanic (Chris) was quoted in the Boat US article and I guess the
> problem comes about when the two gasolines are mixed together. Forms a
> sludge and just makes a royal mess!
I'd be inclined to blame the ethanol for liberating accumulated varnish
and sludge in a seasonal-use engine than for precipitates.
[snip]
> I had a pisser of a time with my 90HP Honda 4 stroke outboard this past
> spring. Clogged passageways, rough running, crapped up lines etc. Cost me
> over $500 to have repaired, and it had to be done a second time!!(No cost)
> My mechanic (Chris) was quoted in the Boat US article and I guess the
> problem comes about when the two gasolines are mixed together. Forms a
> sludge and just makes a royal mess!
I'd be inclined to blame the ethanol for liberating accumulated varnish
and sludge in a seasonal-use engine than for precipitates.
#45
Guest
Posts: n/a
Re: MTBE to Ethanol additive change-over ..PROBLEMS
Kevin Gunther wrote:
[snip]
> I had a pisser of a time with my 90HP Honda 4 stroke outboard this past
> spring. Clogged passageways, rough running, crapped up lines etc. Cost me
> over $500 to have repaired, and it had to be done a second time!!(No cost)
> My mechanic (Chris) was quoted in the Boat US article and I guess the
> problem comes about when the two gasolines are mixed together. Forms a
> sludge and just makes a royal mess!
I'd be inclined to blame the ethanol for liberating accumulated varnish
and sludge in a seasonal-use engine than for precipitates.
[snip]
> I had a pisser of a time with my 90HP Honda 4 stroke outboard this past
> spring. Clogged passageways, rough running, crapped up lines etc. Cost me
> over $500 to have repaired, and it had to be done a second time!!(No cost)
> My mechanic (Chris) was quoted in the Boat US article and I guess the
> problem comes about when the two gasolines are mixed together. Forms a
> sludge and just makes a royal mess!
I'd be inclined to blame the ethanol for liberating accumulated varnish
and sludge in a seasonal-use engine than for precipitates.
#46
Guest
Posts: n/a
Re: MTBE to Ethanol additive change-over ..PROBLEMS
Kevin Gunther wrote:
[snip]
> I had a pisser of a time with my 90HP Honda 4 stroke outboard this past
> spring. Clogged passageways, rough running, crapped up lines etc. Cost me
> over $500 to have repaired, and it had to be done a second time!!(No cost)
> My mechanic (Chris) was quoted in the Boat US article and I guess the
> problem comes about when the two gasolines are mixed together. Forms a
> sludge and just makes a royal mess!
I'd be inclined to blame the ethanol for liberating accumulated varnish
and sludge in a seasonal-use engine than for precipitates.
[snip]
> I had a pisser of a time with my 90HP Honda 4 stroke outboard this past
> spring. Clogged passageways, rough running, crapped up lines etc. Cost me
> over $500 to have repaired, and it had to be done a second time!!(No cost)
> My mechanic (Chris) was quoted in the Boat US article and I guess the
> problem comes about when the two gasolines are mixed together. Forms a
> sludge and just makes a royal mess!
I'd be inclined to blame the ethanol for liberating accumulated varnish
and sludge in a seasonal-use engine than for precipitates.
#47
Guest
Posts: n/a
Re: MTBE to Ethanol additive change-over ..PROBLEMS
Definitely the FRG tanks made before the mid 80s are begining to show
severe attack and 'penetration/leaking' .... and you definitely do not
want free gasoline in the bilge of a boat ..... goes BOOM. The
insurance underwriters that follow the boating industry are currently
'frantic' about the MTBE to ethanol changeover.
In article <dpjeon$26i$1@reader2.panix.com>, Lee Ayrton
<layrton@panix.com> wrote:
> IANAPetrochemicalEngineer, but I can't find anything online about MTBE
> and ethanol forming precipitates. I've found that the US EPA does
> generally forbid mixing the two products in bulk, but there's no ban on
> mixing in the consumer's tanks. The rational for the ban has to do with
> increased Volatile Organic Compound emissions, not chemical
> incompatibility.
>
> The following ethanol industry technical paper states that all
> fiberglass tanks designed for gasoline are compatible with
> gasoline/ethanol blends up to 10% ethanol, and that it has approval
> letters on file from both Fluid Containment (formerly Owens Corning
> Fiberglass) and Xerxes Corp, the two major commercial fiberglass tank
> manufacturers. (pg. 16) It goes on to say that tank relining materials
> using epoxy or polyester resins from the late 1970s and early 1980s are
> not compatible. Page 18 has a short chart of compatible and
> incompatible materials.
>
> <URL:http://www.e85fuel.com/forsuppliers/rfa_technical_manual.pdf> Or:
>
> <URL:http://64.233.187.104/search?q=cache...el.com/forsupp
> liers/rfa_technical_manual.pdf&hl=en>
>
> Without having looked at the OP's pdf I'm guessing that the boatyard is
> having problems with boat tanks older than 1980.
>
>
> reconair wrote:
> > There's really more to it than that. MTBE additives and Ethanol are not
> > compatible and will cause precipitates to form that affects fuel line/fuel
> > filter delivery and cause combustion problems. When switching from MTBE
> > fuel to Ethanol fuel, make sure you run the tank near dry before refueling
> > and vice versa. This will limit the effects of incompatibility.
> >
> > Scott
> > 91YJ
> > "Rich Hampel" <RhmpL33@nospam.net> wrote in message
> > news:040120061152437988%RhmpL33@nospam.net...
> >
> >>although this affects mainly boats, I thought I'd cross post this here
> >>in case any of you have a fiberglass fuel tank.
> >>
> >>There are great 'problems' showing up due to the 'changeover' of
> >>gasoline addives - MTBE to Ethanol: Fiberglass fuel tanks dissolving
> >>and leaking, harmful destructive deposits formed inside engines, etc.
> >>About half the USA states have already banned MTBE additive and are
> >>rapidly changing over to an ethanol additive, the ethanol is quite
> >>incompatible with most of the fiberglass resin used in fuel tanks. The
> >>decomposition products of the 'melting/dissolving' resin doesnt burn
> >>and will form vast and destructive deposits in the engine (similar to
> >>putting sugar into the gasoline).
> >>
> >>for more info:
> >>http://www.moyermarine.com/forums/at...ttachmentid=42
> >>or BOATUS.com website.
> >
> >
> >
severe attack and 'penetration/leaking' .... and you definitely do not
want free gasoline in the bilge of a boat ..... goes BOOM. The
insurance underwriters that follow the boating industry are currently
'frantic' about the MTBE to ethanol changeover.
In article <dpjeon$26i$1@reader2.panix.com>, Lee Ayrton
<layrton@panix.com> wrote:
> IANAPetrochemicalEngineer, but I can't find anything online about MTBE
> and ethanol forming precipitates. I've found that the US EPA does
> generally forbid mixing the two products in bulk, but there's no ban on
> mixing in the consumer's tanks. The rational for the ban has to do with
> increased Volatile Organic Compound emissions, not chemical
> incompatibility.
>
> The following ethanol industry technical paper states that all
> fiberglass tanks designed for gasoline are compatible with
> gasoline/ethanol blends up to 10% ethanol, and that it has approval
> letters on file from both Fluid Containment (formerly Owens Corning
> Fiberglass) and Xerxes Corp, the two major commercial fiberglass tank
> manufacturers. (pg. 16) It goes on to say that tank relining materials
> using epoxy or polyester resins from the late 1970s and early 1980s are
> not compatible. Page 18 has a short chart of compatible and
> incompatible materials.
>
> <URL:http://www.e85fuel.com/forsuppliers/rfa_technical_manual.pdf> Or:
>
> <URL:http://64.233.187.104/search?q=cache...el.com/forsupp
> liers/rfa_technical_manual.pdf&hl=en>
>
> Without having looked at the OP's pdf I'm guessing that the boatyard is
> having problems with boat tanks older than 1980.
>
>
> reconair wrote:
> > There's really more to it than that. MTBE additives and Ethanol are not
> > compatible and will cause precipitates to form that affects fuel line/fuel
> > filter delivery and cause combustion problems. When switching from MTBE
> > fuel to Ethanol fuel, make sure you run the tank near dry before refueling
> > and vice versa. This will limit the effects of incompatibility.
> >
> > Scott
> > 91YJ
> > "Rich Hampel" <RhmpL33@nospam.net> wrote in message
> > news:040120061152437988%RhmpL33@nospam.net...
> >
> >>although this affects mainly boats, I thought I'd cross post this here
> >>in case any of you have a fiberglass fuel tank.
> >>
> >>There are great 'problems' showing up due to the 'changeover' of
> >>gasoline addives - MTBE to Ethanol: Fiberglass fuel tanks dissolving
> >>and leaking, harmful destructive deposits formed inside engines, etc.
> >>About half the USA states have already banned MTBE additive and are
> >>rapidly changing over to an ethanol additive, the ethanol is quite
> >>incompatible with most of the fiberglass resin used in fuel tanks. The
> >>decomposition products of the 'melting/dissolving' resin doesnt burn
> >>and will form vast and destructive deposits in the engine (similar to
> >>putting sugar into the gasoline).
> >>
> >>for more info:
> >>http://www.moyermarine.com/forums/at...ttachmentid=42
> >>or BOATUS.com website.
> >
> >
> >
#48
Guest
Posts: n/a
Re: MTBE to Ethanol additive change-over ..PROBLEMS
Definitely the FRG tanks made before the mid 80s are begining to show
severe attack and 'penetration/leaking' .... and you definitely do not
want free gasoline in the bilge of a boat ..... goes BOOM. The
insurance underwriters that follow the boating industry are currently
'frantic' about the MTBE to ethanol changeover.
In article <dpjeon$26i$1@reader2.panix.com>, Lee Ayrton
<layrton@panix.com> wrote:
> IANAPetrochemicalEngineer, but I can't find anything online about MTBE
> and ethanol forming precipitates. I've found that the US EPA does
> generally forbid mixing the two products in bulk, but there's no ban on
> mixing in the consumer's tanks. The rational for the ban has to do with
> increased Volatile Organic Compound emissions, not chemical
> incompatibility.
>
> The following ethanol industry technical paper states that all
> fiberglass tanks designed for gasoline are compatible with
> gasoline/ethanol blends up to 10% ethanol, and that it has approval
> letters on file from both Fluid Containment (formerly Owens Corning
> Fiberglass) and Xerxes Corp, the two major commercial fiberglass tank
> manufacturers. (pg. 16) It goes on to say that tank relining materials
> using epoxy or polyester resins from the late 1970s and early 1980s are
> not compatible. Page 18 has a short chart of compatible and
> incompatible materials.
>
> <URL:http://www.e85fuel.com/forsuppliers/rfa_technical_manual.pdf> Or:
>
> <URL:http://64.233.187.104/search?q=cache...el.com/forsupp
> liers/rfa_technical_manual.pdf&hl=en>
>
> Without having looked at the OP's pdf I'm guessing that the boatyard is
> having problems with boat tanks older than 1980.
>
>
> reconair wrote:
> > There's really more to it than that. MTBE additives and Ethanol are not
> > compatible and will cause precipitates to form that affects fuel line/fuel
> > filter delivery and cause combustion problems. When switching from MTBE
> > fuel to Ethanol fuel, make sure you run the tank near dry before refueling
> > and vice versa. This will limit the effects of incompatibility.
> >
> > Scott
> > 91YJ
> > "Rich Hampel" <RhmpL33@nospam.net> wrote in message
> > news:040120061152437988%RhmpL33@nospam.net...
> >
> >>although this affects mainly boats, I thought I'd cross post this here
> >>in case any of you have a fiberglass fuel tank.
> >>
> >>There are great 'problems' showing up due to the 'changeover' of
> >>gasoline addives - MTBE to Ethanol: Fiberglass fuel tanks dissolving
> >>and leaking, harmful destructive deposits formed inside engines, etc.
> >>About half the USA states have already banned MTBE additive and are
> >>rapidly changing over to an ethanol additive, the ethanol is quite
> >>incompatible with most of the fiberglass resin used in fuel tanks. The
> >>decomposition products of the 'melting/dissolving' resin doesnt burn
> >>and will form vast and destructive deposits in the engine (similar to
> >>putting sugar into the gasoline).
> >>
> >>for more info:
> >>http://www.moyermarine.com/forums/at...ttachmentid=42
> >>or BOATUS.com website.
> >
> >
> >
severe attack and 'penetration/leaking' .... and you definitely do not
want free gasoline in the bilge of a boat ..... goes BOOM. The
insurance underwriters that follow the boating industry are currently
'frantic' about the MTBE to ethanol changeover.
In article <dpjeon$26i$1@reader2.panix.com>, Lee Ayrton
<layrton@panix.com> wrote:
> IANAPetrochemicalEngineer, but I can't find anything online about MTBE
> and ethanol forming precipitates. I've found that the US EPA does
> generally forbid mixing the two products in bulk, but there's no ban on
> mixing in the consumer's tanks. The rational for the ban has to do with
> increased Volatile Organic Compound emissions, not chemical
> incompatibility.
>
> The following ethanol industry technical paper states that all
> fiberglass tanks designed for gasoline are compatible with
> gasoline/ethanol blends up to 10% ethanol, and that it has approval
> letters on file from both Fluid Containment (formerly Owens Corning
> Fiberglass) and Xerxes Corp, the two major commercial fiberglass tank
> manufacturers. (pg. 16) It goes on to say that tank relining materials
> using epoxy or polyester resins from the late 1970s and early 1980s are
> not compatible. Page 18 has a short chart of compatible and
> incompatible materials.
>
> <URL:http://www.e85fuel.com/forsuppliers/rfa_technical_manual.pdf> Or:
>
> <URL:http://64.233.187.104/search?q=cache...el.com/forsupp
> liers/rfa_technical_manual.pdf&hl=en>
>
> Without having looked at the OP's pdf I'm guessing that the boatyard is
> having problems with boat tanks older than 1980.
>
>
> reconair wrote:
> > There's really more to it than that. MTBE additives and Ethanol are not
> > compatible and will cause precipitates to form that affects fuel line/fuel
> > filter delivery and cause combustion problems. When switching from MTBE
> > fuel to Ethanol fuel, make sure you run the tank near dry before refueling
> > and vice versa. This will limit the effects of incompatibility.
> >
> > Scott
> > 91YJ
> > "Rich Hampel" <RhmpL33@nospam.net> wrote in message
> > news:040120061152437988%RhmpL33@nospam.net...
> >
> >>although this affects mainly boats, I thought I'd cross post this here
> >>in case any of you have a fiberglass fuel tank.
> >>
> >>There are great 'problems' showing up due to the 'changeover' of
> >>gasoline addives - MTBE to Ethanol: Fiberglass fuel tanks dissolving
> >>and leaking, harmful destructive deposits formed inside engines, etc.
> >>About half the USA states have already banned MTBE additive and are
> >>rapidly changing over to an ethanol additive, the ethanol is quite
> >>incompatible with most of the fiberglass resin used in fuel tanks. The
> >>decomposition products of the 'melting/dissolving' resin doesnt burn
> >>and will form vast and destructive deposits in the engine (similar to
> >>putting sugar into the gasoline).
> >>
> >>for more info:
> >>http://www.moyermarine.com/forums/at...ttachmentid=42
> >>or BOATUS.com website.
> >
> >
> >
#49
Guest
Posts: n/a
Re: MTBE to Ethanol additive change-over ..PROBLEMS
Definitely the FRG tanks made before the mid 80s are begining to show
severe attack and 'penetration/leaking' .... and you definitely do not
want free gasoline in the bilge of a boat ..... goes BOOM. The
insurance underwriters that follow the boating industry are currently
'frantic' about the MTBE to ethanol changeover.
In article <dpjeon$26i$1@reader2.panix.com>, Lee Ayrton
<layrton@panix.com> wrote:
> IANAPetrochemicalEngineer, but I can't find anything online about MTBE
> and ethanol forming precipitates. I've found that the US EPA does
> generally forbid mixing the two products in bulk, but there's no ban on
> mixing in the consumer's tanks. The rational for the ban has to do with
> increased Volatile Organic Compound emissions, not chemical
> incompatibility.
>
> The following ethanol industry technical paper states that all
> fiberglass tanks designed for gasoline are compatible with
> gasoline/ethanol blends up to 10% ethanol, and that it has approval
> letters on file from both Fluid Containment (formerly Owens Corning
> Fiberglass) and Xerxes Corp, the two major commercial fiberglass tank
> manufacturers. (pg. 16) It goes on to say that tank relining materials
> using epoxy or polyester resins from the late 1970s and early 1980s are
> not compatible. Page 18 has a short chart of compatible and
> incompatible materials.
>
> <URL:http://www.e85fuel.com/forsuppliers/rfa_technical_manual.pdf> Or:
>
> <URL:http://64.233.187.104/search?q=cache...el.com/forsupp
> liers/rfa_technical_manual.pdf&hl=en>
>
> Without having looked at the OP's pdf I'm guessing that the boatyard is
> having problems with boat tanks older than 1980.
>
>
> reconair wrote:
> > There's really more to it than that. MTBE additives and Ethanol are not
> > compatible and will cause precipitates to form that affects fuel line/fuel
> > filter delivery and cause combustion problems. When switching from MTBE
> > fuel to Ethanol fuel, make sure you run the tank near dry before refueling
> > and vice versa. This will limit the effects of incompatibility.
> >
> > Scott
> > 91YJ
> > "Rich Hampel" <RhmpL33@nospam.net> wrote in message
> > news:040120061152437988%RhmpL33@nospam.net...
> >
> >>although this affects mainly boats, I thought I'd cross post this here
> >>in case any of you have a fiberglass fuel tank.
> >>
> >>There are great 'problems' showing up due to the 'changeover' of
> >>gasoline addives - MTBE to Ethanol: Fiberglass fuel tanks dissolving
> >>and leaking, harmful destructive deposits formed inside engines, etc.
> >>About half the USA states have already banned MTBE additive and are
> >>rapidly changing over to an ethanol additive, the ethanol is quite
> >>incompatible with most of the fiberglass resin used in fuel tanks. The
> >>decomposition products of the 'melting/dissolving' resin doesnt burn
> >>and will form vast and destructive deposits in the engine (similar to
> >>putting sugar into the gasoline).
> >>
> >>for more info:
> >>http://www.moyermarine.com/forums/at...ttachmentid=42
> >>or BOATUS.com website.
> >
> >
> >
severe attack and 'penetration/leaking' .... and you definitely do not
want free gasoline in the bilge of a boat ..... goes BOOM. The
insurance underwriters that follow the boating industry are currently
'frantic' about the MTBE to ethanol changeover.
In article <dpjeon$26i$1@reader2.panix.com>, Lee Ayrton
<layrton@panix.com> wrote:
> IANAPetrochemicalEngineer, but I can't find anything online about MTBE
> and ethanol forming precipitates. I've found that the US EPA does
> generally forbid mixing the two products in bulk, but there's no ban on
> mixing in the consumer's tanks. The rational for the ban has to do with
> increased Volatile Organic Compound emissions, not chemical
> incompatibility.
>
> The following ethanol industry technical paper states that all
> fiberglass tanks designed for gasoline are compatible with
> gasoline/ethanol blends up to 10% ethanol, and that it has approval
> letters on file from both Fluid Containment (formerly Owens Corning
> Fiberglass) and Xerxes Corp, the two major commercial fiberglass tank
> manufacturers. (pg. 16) It goes on to say that tank relining materials
> using epoxy or polyester resins from the late 1970s and early 1980s are
> not compatible. Page 18 has a short chart of compatible and
> incompatible materials.
>
> <URL:http://www.e85fuel.com/forsuppliers/rfa_technical_manual.pdf> Or:
>
> <URL:http://64.233.187.104/search?q=cache...el.com/forsupp
> liers/rfa_technical_manual.pdf&hl=en>
>
> Without having looked at the OP's pdf I'm guessing that the boatyard is
> having problems with boat tanks older than 1980.
>
>
> reconair wrote:
> > There's really more to it than that. MTBE additives and Ethanol are not
> > compatible and will cause precipitates to form that affects fuel line/fuel
> > filter delivery and cause combustion problems. When switching from MTBE
> > fuel to Ethanol fuel, make sure you run the tank near dry before refueling
> > and vice versa. This will limit the effects of incompatibility.
> >
> > Scott
> > 91YJ
> > "Rich Hampel" <RhmpL33@nospam.net> wrote in message
> > news:040120061152437988%RhmpL33@nospam.net...
> >
> >>although this affects mainly boats, I thought I'd cross post this here
> >>in case any of you have a fiberglass fuel tank.
> >>
> >>There are great 'problems' showing up due to the 'changeover' of
> >>gasoline addives - MTBE to Ethanol: Fiberglass fuel tanks dissolving
> >>and leaking, harmful destructive deposits formed inside engines, etc.
> >>About half the USA states have already banned MTBE additive and are
> >>rapidly changing over to an ethanol additive, the ethanol is quite
> >>incompatible with most of the fiberglass resin used in fuel tanks. The
> >>decomposition products of the 'melting/dissolving' resin doesnt burn
> >>and will form vast and destructive deposits in the engine (similar to
> >>putting sugar into the gasoline).
> >>
> >>for more info:
> >>http://www.moyermarine.com/forums/at...ttachmentid=42
> >>or BOATUS.com website.
> >
> >
> >
#50
Guest
Posts: n/a
Re: MTBE to Ethanol additive change-over ..PROBLEMS
"Lee Ayrton" <layrton@panix.com> wrote in message
news:dpjjga$j2h$1@reader2.panix.com...
> Kevin Gunther wrote:
> [snip]
> > I had a pisser of a time with my 90HP Honda 4 stroke outboard this past
> > spring. Clogged passageways, rough running, crapped up lines etc. Cost
me
> > over $500 to have repaired, and it had to be done a second time!!(No
cost)
> > My mechanic (Chris) was quoted in the Boat US article and I guess the
> > problem comes about when the two gasolines are mixed together. Forms a
> > sludge and just makes a royal mess!
>
> I'd be inclined to blame the ethanol for liberating accumulated varnish
> and sludge in a seasonal-use engine than for precipitates.
That might be a problem with an older engine, but this engine was only on
its fourth season. I had run it out, fogged it and stabil'ed it each fall.
It was the combination of the fuel types. Boaters all over the stases of NT
and CT were having this problem. Take a look at the BoatUS article.
KG
>
>
>