Where is the keyless module? Gr Cherokee 96
Guest
Posts: n/a
Re: Where is the keyless module? Gr Cherokee 96
drivers lower dash you will find the bcm and thats were you tie into the
keyless entry
JS wrote:
> I want to hook up my remote starter to the keyless entry module to
> unlock/lock doors but cant find the wires or module. Can someone help with
> the location of the module or wires ??
>
> thanks
keyless entry
JS wrote:
> I want to hook up my remote starter to the keyless entry module to
> unlock/lock doors but cant find the wires or module. Can someone help with
> the location of the module or wires ??
>
> thanks
Guest
Posts: n/a
Re: Where is the keyless module? Gr Cherokee 96
drivers lower dash you will find the bcm and thats were you tie into the
keyless entry
JS wrote:
> I want to hook up my remote starter to the keyless entry module to
> unlock/lock doors but cant find the wires or module. Can someone help with
> the location of the module or wires ??
>
> thanks
keyless entry
JS wrote:
> I want to hook up my remote starter to the keyless entry module to
> unlock/lock doors but cant find the wires or module. Can someone help with
> the location of the module or wires ??
>
> thanks
Guest
Posts: n/a
Re: Where is the keyless module? Gr Cherokee 96
drivers lower dash you will find the bcm and thats were you tie into the
keyless entry
JS wrote:
> I want to hook up my remote starter to the keyless entry module to
> unlock/lock doors but cant find the wires or module. Can someone help with
> the location of the module or wires ??
>
> thanks
keyless entry
JS wrote:
> I want to hook up my remote starter to the keyless entry module to
> unlock/lock doors but cant find the wires or module. Can someone help with
> the location of the module or wires ??
>
> thanks
Guest
Posts: n/a
Re: Where is the keyless module? Gr Cherokee 96
93 to 95 did not have a bcm were 96 does and that is the main hub
DougW wrote:
> JS did pass the time by typing:
> > I want to hook up my remote starter to the keyless entry module to
> > unlock/lock doors but cant find the wires or module. Can someone help with
> > the location of the module or wires ??
>
> All I have is 93 schematics and I don't think they are valid past 95.
>
> The 93 uses two wires, one to lock, one to unlock.
>
> On mine the relay center is located under a panel in the glove box
> it was hard to get at so I intercepted the harness as it went to the
> drivers door. Those were 20 Gauge wires,
> Pink with Violet stripe for unlock
> Orange with Violet stripe for lock
>
> You could check the wires coming from the door and look for the ones that
> get 12V when you hit lock/unlock.
>
> ... problem is that doesn't disarm the stock alarm system ...
>
> To solve that I traced the entry keys disarm switch from the
> driver door (18 gauge violet with yellow stripe) and tied it
> to ground using a relay that kicks off when the unlock signal
> hits.
>
> Drawback, this means that anytime someone hits the unlock button
> it disarms the stock alarm. Not a good thing. I didn't care because
> it was a Clifford alarm system with remote start that was going in.
>
> If your remote starter has a disarm output (or ground closure) you
> could probably use that directly. Me, I like using those little bitty
> 12v relays.
>
> --
> -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> Banks Header - and BEER, in the fridge!
DougW wrote:
> JS did pass the time by typing:
> > I want to hook up my remote starter to the keyless entry module to
> > unlock/lock doors but cant find the wires or module. Can someone help with
> > the location of the module or wires ??
>
> All I have is 93 schematics and I don't think they are valid past 95.
>
> The 93 uses two wires, one to lock, one to unlock.
>
> On mine the relay center is located under a panel in the glove box
> it was hard to get at so I intercepted the harness as it went to the
> drivers door. Those were 20 Gauge wires,
> Pink with Violet stripe for unlock
> Orange with Violet stripe for lock
>
> You could check the wires coming from the door and look for the ones that
> get 12V when you hit lock/unlock.
>
> ... problem is that doesn't disarm the stock alarm system ...
>
> To solve that I traced the entry keys disarm switch from the
> driver door (18 gauge violet with yellow stripe) and tied it
> to ground using a relay that kicks off when the unlock signal
> hits.
>
> Drawback, this means that anytime someone hits the unlock button
> it disarms the stock alarm. Not a good thing. I didn't care because
> it was a Clifford alarm system with remote start that was going in.
>
> If your remote starter has a disarm output (or ground closure) you
> could probably use that directly. Me, I like using those little bitty
> 12v relays.
>
> --
> -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> Banks Header - and BEER, in the fridge!
Guest
Posts: n/a
Re: Where is the keyless module? Gr Cherokee 96
93 to 95 did not have a bcm were 96 does and that is the main hub
DougW wrote:
> JS did pass the time by typing:
> > I want to hook up my remote starter to the keyless entry module to
> > unlock/lock doors but cant find the wires or module. Can someone help with
> > the location of the module or wires ??
>
> All I have is 93 schematics and I don't think they are valid past 95.
>
> The 93 uses two wires, one to lock, one to unlock.
>
> On mine the relay center is located under a panel in the glove box
> it was hard to get at so I intercepted the harness as it went to the
> drivers door. Those were 20 Gauge wires,
> Pink with Violet stripe for unlock
> Orange with Violet stripe for lock
>
> You could check the wires coming from the door and look for the ones that
> get 12V when you hit lock/unlock.
>
> ... problem is that doesn't disarm the stock alarm system ...
>
> To solve that I traced the entry keys disarm switch from the
> driver door (18 gauge violet with yellow stripe) and tied it
> to ground using a relay that kicks off when the unlock signal
> hits.
>
> Drawback, this means that anytime someone hits the unlock button
> it disarms the stock alarm. Not a good thing. I didn't care because
> it was a Clifford alarm system with remote start that was going in.
>
> If your remote starter has a disarm output (or ground closure) you
> could probably use that directly. Me, I like using those little bitty
> 12v relays.
>
> --
> -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> Banks Header - and BEER, in the fridge!
DougW wrote:
> JS did pass the time by typing:
> > I want to hook up my remote starter to the keyless entry module to
> > unlock/lock doors but cant find the wires or module. Can someone help with
> > the location of the module or wires ??
>
> All I have is 93 schematics and I don't think they are valid past 95.
>
> The 93 uses two wires, one to lock, one to unlock.
>
> On mine the relay center is located under a panel in the glove box
> it was hard to get at so I intercepted the harness as it went to the
> drivers door. Those were 20 Gauge wires,
> Pink with Violet stripe for unlock
> Orange with Violet stripe for lock
>
> You could check the wires coming from the door and look for the ones that
> get 12V when you hit lock/unlock.
>
> ... problem is that doesn't disarm the stock alarm system ...
>
> To solve that I traced the entry keys disarm switch from the
> driver door (18 gauge violet with yellow stripe) and tied it
> to ground using a relay that kicks off when the unlock signal
> hits.
>
> Drawback, this means that anytime someone hits the unlock button
> it disarms the stock alarm. Not a good thing. I didn't care because
> it was a Clifford alarm system with remote start that was going in.
>
> If your remote starter has a disarm output (or ground closure) you
> could probably use that directly. Me, I like using those little bitty
> 12v relays.
>
> --
> -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> Banks Header - and BEER, in the fridge!
Guest
Posts: n/a
Re: Where is the keyless module? Gr Cherokee 96
93 to 95 did not have a bcm were 96 does and that is the main hub
DougW wrote:
> JS did pass the time by typing:
> > I want to hook up my remote starter to the keyless entry module to
> > unlock/lock doors but cant find the wires or module. Can someone help with
> > the location of the module or wires ??
>
> All I have is 93 schematics and I don't think they are valid past 95.
>
> The 93 uses two wires, one to lock, one to unlock.
>
> On mine the relay center is located under a panel in the glove box
> it was hard to get at so I intercepted the harness as it went to the
> drivers door. Those were 20 Gauge wires,
> Pink with Violet stripe for unlock
> Orange with Violet stripe for lock
>
> You could check the wires coming from the door and look for the ones that
> get 12V when you hit lock/unlock.
>
> ... problem is that doesn't disarm the stock alarm system ...
>
> To solve that I traced the entry keys disarm switch from the
> driver door (18 gauge violet with yellow stripe) and tied it
> to ground using a relay that kicks off when the unlock signal
> hits.
>
> Drawback, this means that anytime someone hits the unlock button
> it disarms the stock alarm. Not a good thing. I didn't care because
> it was a Clifford alarm system with remote start that was going in.
>
> If your remote starter has a disarm output (or ground closure) you
> could probably use that directly. Me, I like using those little bitty
> 12v relays.
>
> --
> -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> Banks Header - and BEER, in the fridge!
DougW wrote:
> JS did pass the time by typing:
> > I want to hook up my remote starter to the keyless entry module to
> > unlock/lock doors but cant find the wires or module. Can someone help with
> > the location of the module or wires ??
>
> All I have is 93 schematics and I don't think they are valid past 95.
>
> The 93 uses two wires, one to lock, one to unlock.
>
> On mine the relay center is located under a panel in the glove box
> it was hard to get at so I intercepted the harness as it went to the
> drivers door. Those were 20 Gauge wires,
> Pink with Violet stripe for unlock
> Orange with Violet stripe for lock
>
> You could check the wires coming from the door and look for the ones that
> get 12V when you hit lock/unlock.
>
> ... problem is that doesn't disarm the stock alarm system ...
>
> To solve that I traced the entry keys disarm switch from the
> driver door (18 gauge violet with yellow stripe) and tied it
> to ground using a relay that kicks off when the unlock signal
> hits.
>
> Drawback, this means that anytime someone hits the unlock button
> it disarms the stock alarm. Not a good thing. I didn't care because
> it was a Clifford alarm system with remote start that was going in.
>
> If your remote starter has a disarm output (or ground closure) you
> could probably use that directly. Me, I like using those little bitty
> 12v relays.
>
> --
> -- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
> HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
> Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
> Banks Header - and BEER, in the fridge!
Guest
Posts: n/a
Re: Where is the keyless module? Gr Cherokee 96
http://groups.google.com/group/rec.a...rch+this+group
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
JS wrote:
>
> I want to hook up my remote starter to the keyless entry module to
> unlock/lock doors but cant find the wires or module. Can someone help with
> the location of the module or wires ??
>
> thanks
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
JS wrote:
>
> I want to hook up my remote starter to the keyless entry module to
> unlock/lock doors but cant find the wires or module. Can someone help with
> the location of the module or wires ??
>
> thanks
Guest
Posts: n/a
Re: Where is the keyless module? Gr Cherokee 96
http://groups.google.com/group/rec.a...rch+this+group
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
JS wrote:
>
> I want to hook up my remote starter to the keyless entry module to
> unlock/lock doors but cant find the wires or module. Can someone help with
> the location of the module or wires ??
>
> thanks
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
JS wrote:
>
> I want to hook up my remote starter to the keyless entry module to
> unlock/lock doors but cant find the wires or module. Can someone help with
> the location of the module or wires ??
>
> thanks
Guest
Posts: n/a
Re: Where is the keyless module? Gr Cherokee 96
http://groups.google.com/group/rec.a...rch+this+group
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
JS wrote:
>
> I want to hook up my remote starter to the keyless entry module to
> unlock/lock doors but cant find the wires or module. Can someone help with
> the location of the module or wires ??
>
> thanks
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
JS wrote:
>
> I want to hook up my remote starter to the keyless entry module to
> unlock/lock doors but cant find the wires or module. Can someone help with
> the location of the module or wires ??
>
> thanks
Thread
Thread Starter
Forum
Replies
Last Post
Don I
Jeep Mailing List
12
Jan 5, 2004 08:49 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)