Tranny mount done :)
11-26-2004, 05:53 PM
#1
Guest
Posts: n/a
Tranny mount done :)
Well, the front motor mounts were done and that
brought the supercharger into close contact with
the ABS system.. causing some interesting results
in reverse. :(
Checked the tranny mount and it was shot.
(go figure)
Wasn't too hard. The book says just to jack
up the tranny then pull the lower plate. It's
easier to drop the crossmember. Not only does it
give better access it's easier on the tranny than
jacking it up. (still have to move it a bit but it's
less stress on the pan)
That and some gorilla on crack must have torqued
down that last mount. The freeking bolt only goes
to 34 ft.lbs but it took a 4' cheater and one hell
of a grunt to break it free. Actually twisted up
my cheap *** korean 1/2-3/8 adapter. Gonna get one
from Snap-On. Saved enough on the labor and parts.
Dealer wanted 300 for the motor mounts and 190 for
the tranny. sheesh.
Now I can justify new tools.. :D
And aspirin.
.....lots of aspirin.
--
DougW
brought the supercharger into close contact with
the ABS system.. causing some interesting results
in reverse. :(
Checked the tranny mount and it was shot.
(go figure)
Wasn't too hard. The book says just to jack
up the tranny then pull the lower plate. It's
easier to drop the crossmember. Not only does it
give better access it's easier on the tranny than
jacking it up. (still have to move it a bit but it's
less stress on the pan)
That and some gorilla on crack must have torqued
down that last mount. The freeking bolt only goes
to 34 ft.lbs but it took a 4' cheater and one hell
of a grunt to break it free. Actually twisted up
my cheap *** korean 1/2-3/8 adapter. Gonna get one
from Snap-On. Saved enough on the labor and parts.
Dealer wanted 300 for the motor mounts and 190 for
the tranny. sheesh.
Now I can justify new tools.. :D
And aspirin.
.....lots of aspirin.
--
DougW
11-26-2004, 06:04 PM
#2
Guest
Posts: n/a
Re: Tranny mount done :)
190 for the tranny mount? wow.. now was that a 4' cheater bar sober or w/
beer muscles? ;) I've got to do mine soon., also.
Paul
"DougW" <post.replies@invalid.address> wrote in message
news:ovOpd.102412$tU4.59947@okepread06...
> Well, the front motor mounts were done and that
> brought the supercharger into close contact with
> the ABS system.. causing some interesting results
> in reverse. :(
>
> Checked the tranny mount and it was shot.
> (go figure)
>
> Wasn't too hard. The book says just to jack
> up the tranny then pull the lower plate. It's
> easier to drop the crossmember. Not only does it
> give better access it's easier on the tranny than
> jacking it up. (still have to move it a bit but it's
> less stress on the pan)
>
> That and some gorilla on crack must have torqued
> down that last mount. The freeking bolt only goes
> to 34 ft.lbs but it took a 4' cheater and one hell
> of a grunt to break it free. Actually twisted up
> my cheap *** korean 1/2-3/8 adapter. Gonna get one
> from Snap-On. Saved enough on the labor and parts.
>
> Dealer wanted 300 for the motor mounts and 190 for
> the tranny. sheesh.
>
> Now I can justify new tools.. :D
>
> And aspirin.
>
> ....lots of aspirin.
>
> --
> DougW
>
beer muscles? ;) I've got to do mine soon., also.
Paul
"DougW" <post.replies@invalid.address> wrote in message
news:ovOpd.102412$tU4.59947@okepread06...
> Well, the front motor mounts were done and that
> brought the supercharger into close contact with
> the ABS system.. causing some interesting results
> in reverse. :(
>
> Checked the tranny mount and it was shot.
> (go figure)
>
> Wasn't too hard. The book says just to jack
> up the tranny then pull the lower plate. It's
> easier to drop the crossmember. Not only does it
> give better access it's easier on the tranny than
> jacking it up. (still have to move it a bit but it's
> less stress on the pan)
>
> That and some gorilla on crack must have torqued
> down that last mount. The freeking bolt only goes
> to 34 ft.lbs but it took a 4' cheater and one hell
> of a grunt to break it free. Actually twisted up
> my cheap *** korean 1/2-3/8 adapter. Gonna get one
> from Snap-On. Saved enough on the labor and parts.
>
> Dealer wanted 300 for the motor mounts and 190 for
> the tranny. sheesh.
>
> Now I can justify new tools.. :D
>
> And aspirin.
>
> ....lots of aspirin.
>
> --
> DougW
>
11-26-2004, 06:04 PM
#3
Guest
Posts: n/a
Re: Tranny mount done :)
190 for the tranny mount? wow.. now was that a 4' cheater bar sober or w/
beer muscles? ;) I've got to do mine soon., also.
Paul
"DougW" <post.replies@invalid.address> wrote in message
news:ovOpd.102412$tU4.59947@okepread06...
> Well, the front motor mounts were done and that
> brought the supercharger into close contact with
> the ABS system.. causing some interesting results
> in reverse. :(
>
> Checked the tranny mount and it was shot.
> (go figure)
>
> Wasn't too hard. The book says just to jack
> up the tranny then pull the lower plate. It's
> easier to drop the crossmember. Not only does it
> give better access it's easier on the tranny than
> jacking it up. (still have to move it a bit but it's
> less stress on the pan)
>
> That and some gorilla on crack must have torqued
> down that last mount. The freeking bolt only goes
> to 34 ft.lbs but it took a 4' cheater and one hell
> of a grunt to break it free. Actually twisted up
> my cheap *** korean 1/2-3/8 adapter. Gonna get one
> from Snap-On. Saved enough on the labor and parts.
>
> Dealer wanted 300 for the motor mounts and 190 for
> the tranny. sheesh.
>
> Now I can justify new tools.. :D
>
> And aspirin.
>
> ....lots of aspirin.
>
> --
> DougW
>
beer muscles? ;) I've got to do mine soon., also.
Paul
"DougW" <post.replies@invalid.address> wrote in message
news:ovOpd.102412$tU4.59947@okepread06...
> Well, the front motor mounts were done and that
> brought the supercharger into close contact with
> the ABS system.. causing some interesting results
> in reverse. :(
>
> Checked the tranny mount and it was shot.
> (go figure)
>
> Wasn't too hard. The book says just to jack
> up the tranny then pull the lower plate. It's
> easier to drop the crossmember. Not only does it
> give better access it's easier on the tranny than
> jacking it up. (still have to move it a bit but it's
> less stress on the pan)
>
> That and some gorilla on crack must have torqued
> down that last mount. The freeking bolt only goes
> to 34 ft.lbs but it took a 4' cheater and one hell
> of a grunt to break it free. Actually twisted up
> my cheap *** korean 1/2-3/8 adapter. Gonna get one
> from Snap-On. Saved enough on the labor and parts.
>
> Dealer wanted 300 for the motor mounts and 190 for
> the tranny. sheesh.
>
> Now I can justify new tools.. :D
>
> And aspirin.
>
> ....lots of aspirin.
>
> --
> DougW
>
11-26-2004, 06:04 PM
#4
Guest
Posts: n/a
Re: Tranny mount done :)
190 for the tranny mount? wow.. now was that a 4' cheater bar sober or w/
beer muscles? ;) I've got to do mine soon., also.
Paul
"DougW" <post.replies@invalid.address> wrote in message
news:ovOpd.102412$tU4.59947@okepread06...
> Well, the front motor mounts were done and that
> brought the supercharger into close contact with
> the ABS system.. causing some interesting results
> in reverse. :(
>
> Checked the tranny mount and it was shot.
> (go figure)
>
> Wasn't too hard. The book says just to jack
> up the tranny then pull the lower plate. It's
> easier to drop the crossmember. Not only does it
> give better access it's easier on the tranny than
> jacking it up. (still have to move it a bit but it's
> less stress on the pan)
>
> That and some gorilla on crack must have torqued
> down that last mount. The freeking bolt only goes
> to 34 ft.lbs but it took a 4' cheater and one hell
> of a grunt to break it free. Actually twisted up
> my cheap *** korean 1/2-3/8 adapter. Gonna get one
> from Snap-On. Saved enough on the labor and parts.
>
> Dealer wanted 300 for the motor mounts and 190 for
> the tranny. sheesh.
>
> Now I can justify new tools.. :D
>
> And aspirin.
>
> ....lots of aspirin.
>
> --
> DougW
>
beer muscles? ;) I've got to do mine soon., also.
Paul
"DougW" <post.replies@invalid.address> wrote in message
news:ovOpd.102412$tU4.59947@okepread06...
> Well, the front motor mounts were done and that
> brought the supercharger into close contact with
> the ABS system.. causing some interesting results
> in reverse. :(
>
> Checked the tranny mount and it was shot.
> (go figure)
>
> Wasn't too hard. The book says just to jack
> up the tranny then pull the lower plate. It's
> easier to drop the crossmember. Not only does it
> give better access it's easier on the tranny than
> jacking it up. (still have to move it a bit but it's
> less stress on the pan)
>
> That and some gorilla on crack must have torqued
> down that last mount. The freeking bolt only goes
> to 34 ft.lbs but it took a 4' cheater and one hell
> of a grunt to break it free. Actually twisted up
> my cheap *** korean 1/2-3/8 adapter. Gonna get one
> from Snap-On. Saved enough on the labor and parts.
>
> Dealer wanted 300 for the motor mounts and 190 for
> the tranny. sheesh.
>
> Now I can justify new tools.. :D
>
> And aspirin.
>
> ....lots of aspirin.
>
> --
> DougW
>
11-26-2004, 06:26 PM
#5
Guest
Posts: n/a
Re: Tranny mount done :)
Paw did pass the time by typing:
> 190 for the tranny mount? wow.. now was that a 4' cheater bar sober or w/
> beer muscles? ;) I've got to do mine soon., also.
Should have typed that better. It was $190 for labor and $60
for the part. Had to swallow the $60+tax since (stupid me) didn't
order it with the other parts. Normally I would have got it from
these folks http://www.chryslerpartsdirect.com/ for $44 and shipping.
I wrench sober. Like my beer, but history proves several cans
and vehicle maintenance don't mix well. In this case I had to
brace against the jeep to keep from dragging myself in circles.
When it broke loose I darn near ate the wrench. Beer reaction time
would have equaled a nice welt on mah noggin. :)
Should have a website writeup on the process soonish. Other things
are keeping me busy now.. (like attic insulation) yay.. cough.. yay..
--
DougW
> 190 for the tranny mount? wow.. now was that a 4' cheater bar sober or w/
> beer muscles? ;) I've got to do mine soon., also.
Should have typed that better. It was $190 for labor and $60
for the part. Had to swallow the $60+tax since (stupid me) didn't
order it with the other parts. Normally I would have got it from
these folks http://www.chryslerpartsdirect.com/ for $44 and shipping.
I wrench sober. Like my beer, but history proves several cans
and vehicle maintenance don't mix well. In this case I had to
brace against the jeep to keep from dragging myself in circles.
When it broke loose I darn near ate the wrench. Beer reaction time
would have equaled a nice welt on mah noggin. :)
Should have a website writeup on the process soonish. Other things
are keeping me busy now.. (like attic insulation) yay.. cough.. yay..
--
DougW
11-26-2004, 06:26 PM
#6
Guest
Posts: n/a
Re: Tranny mount done :)
Paw did pass the time by typing:
> 190 for the tranny mount? wow.. now was that a 4' cheater bar sober or w/
> beer muscles? ;) I've got to do mine soon., also.
Should have typed that better. It was $190 for labor and $60
for the part. Had to swallow the $60+tax since (stupid me) didn't
order it with the other parts. Normally I would have got it from
these folks http://www.chryslerpartsdirect.com/ for $44 and shipping.
I wrench sober. Like my beer, but history proves several cans
and vehicle maintenance don't mix well. In this case I had to
brace against the jeep to keep from dragging myself in circles.
When it broke loose I darn near ate the wrench. Beer reaction time
would have equaled a nice welt on mah noggin. :)
Should have a website writeup on the process soonish. Other things
are keeping me busy now.. (like attic insulation) yay.. cough.. yay..
--
DougW
> 190 for the tranny mount? wow.. now was that a 4' cheater bar sober or w/
> beer muscles? ;) I've got to do mine soon., also.
Should have typed that better. It was $190 for labor and $60
for the part. Had to swallow the $60+tax since (stupid me) didn't
order it with the other parts. Normally I would have got it from
these folks http://www.chryslerpartsdirect.com/ for $44 and shipping.
I wrench sober. Like my beer, but history proves several cans
and vehicle maintenance don't mix well. In this case I had to
brace against the jeep to keep from dragging myself in circles.
When it broke loose I darn near ate the wrench. Beer reaction time
would have equaled a nice welt on mah noggin. :)
Should have a website writeup on the process soonish. Other things
are keeping me busy now.. (like attic insulation) yay.. cough.. yay..
--
DougW
11-26-2004, 06:26 PM
#7
Guest
Posts: n/a
Re: Tranny mount done :)
Paw did pass the time by typing:
> 190 for the tranny mount? wow.. now was that a 4' cheater bar sober or w/
> beer muscles? ;) I've got to do mine soon., also.
Should have typed that better. It was $190 for labor and $60
for the part. Had to swallow the $60+tax since (stupid me) didn't
order it with the other parts. Normally I would have got it from
these folks http://www.chryslerpartsdirect.com/ for $44 and shipping.
I wrench sober. Like my beer, but history proves several cans
and vehicle maintenance don't mix well. In this case I had to
brace against the jeep to keep from dragging myself in circles.
When it broke loose I darn near ate the wrench. Beer reaction time
would have equaled a nice welt on mah noggin. :)
Should have a website writeup on the process soonish. Other things
are keeping me busy now.. (like attic insulation) yay.. cough.. yay..
--
DougW
> 190 for the tranny mount? wow.. now was that a 4' cheater bar sober or w/
> beer muscles? ;) I've got to do mine soon., also.
Should have typed that better. It was $190 for labor and $60
for the part. Had to swallow the $60+tax since (stupid me) didn't
order it with the other parts. Normally I would have got it from
these folks http://www.chryslerpartsdirect.com/ for $44 and shipping.
I wrench sober. Like my beer, but history proves several cans
and vehicle maintenance don't mix well. In this case I had to
brace against the jeep to keep from dragging myself in circles.
When it broke loose I darn near ate the wrench. Beer reaction time
would have equaled a nice welt on mah noggin. :)
Should have a website writeup on the process soonish. Other things
are keeping me busy now.. (like attic insulation) yay.. cough.. yay..
--
DougW
11-26-2004, 06:47 PM
#8
Guest
Posts: n/a
Re: Tranny mount done :)
sounds good :) Thanks, I'll wait for the writeup... our 'newer' has has a
finished attic, so no more need of replacing/installing for insulation... I
wear it well......... ;0
Paul
"DougW" <post.replies@invalid.address> wrote in message
news:e_Opd.102413$tU4.41514@okepread06...
> Paw did pass the time by typing:
>> 190 for the tranny mount? wow.. now was that a 4' cheater bar sober or
>> w/
>> beer muscles? ;) I've got to do mine soon., also.
>
> Should have typed that better. It was $190 for labor and $60
> for the part. Had to swallow the $60+tax since (stupid me) didn't
> order it with the other parts. Normally I would have got it from
> these folks http://www.chryslerpartsdirect.com/ for $44 and shipping.
>
> I wrench sober. Like my beer, but history proves several cans
> and vehicle maintenance don't mix well. In this case I had to
> brace against the jeep to keep from dragging myself in circles.
> When it broke loose I darn near ate the wrench. Beer reaction time
> would have equaled a nice welt on mah noggin. :)
>
> Should have a website writeup on the process soonish. Other things
> are keeping me busy now.. (like attic insulation) yay.. cough.. yay..
>
> --
> DougW
>
finished attic, so no more need of replacing/installing for insulation... I
wear it well......... ;0
Paul
"DougW" <post.replies@invalid.address> wrote in message
news:e_Opd.102413$tU4.41514@okepread06...
> Paw did pass the time by typing:
>> 190 for the tranny mount? wow.. now was that a 4' cheater bar sober or
>> w/
>> beer muscles? ;) I've got to do mine soon., also.
>
> Should have typed that better. It was $190 for labor and $60
> for the part. Had to swallow the $60+tax since (stupid me) didn't
> order it with the other parts. Normally I would have got it from
> these folks http://www.chryslerpartsdirect.com/ for $44 and shipping.
>
> I wrench sober. Like my beer, but history proves several cans
> and vehicle maintenance don't mix well. In this case I had to
> brace against the jeep to keep from dragging myself in circles.
> When it broke loose I darn near ate the wrench. Beer reaction time
> would have equaled a nice welt on mah noggin. :)
>
> Should have a website writeup on the process soonish. Other things
> are keeping me busy now.. (like attic insulation) yay.. cough.. yay..
>
> --
> DougW
>
11-26-2004, 06:47 PM
#9
Guest
Posts: n/a
Re: Tranny mount done :)
sounds good :) Thanks, I'll wait for the writeup... our 'newer' has has a
finished attic, so no more need of replacing/installing for insulation... I
wear it well......... ;0
Paul
"DougW" <post.replies@invalid.address> wrote in message
news:e_Opd.102413$tU4.41514@okepread06...
> Paw did pass the time by typing:
>> 190 for the tranny mount? wow.. now was that a 4' cheater bar sober or
>> w/
>> beer muscles? ;) I've got to do mine soon., also.
>
> Should have typed that better. It was $190 for labor and $60
> for the part. Had to swallow the $60+tax since (stupid me) didn't
> order it with the other parts. Normally I would have got it from
> these folks http://www.chryslerpartsdirect.com/ for $44 and shipping.
>
> I wrench sober. Like my beer, but history proves several cans
> and vehicle maintenance don't mix well. In this case I had to
> brace against the jeep to keep from dragging myself in circles.
> When it broke loose I darn near ate the wrench. Beer reaction time
> would have equaled a nice welt on mah noggin. :)
>
> Should have a website writeup on the process soonish. Other things
> are keeping me busy now.. (like attic insulation) yay.. cough.. yay..
>
> --
> DougW
>
finished attic, so no more need of replacing/installing for insulation... I
wear it well......... ;0
Paul
"DougW" <post.replies@invalid.address> wrote in message
news:e_Opd.102413$tU4.41514@okepread06...
> Paw did pass the time by typing:
>> 190 for the tranny mount? wow.. now was that a 4' cheater bar sober or
>> w/
>> beer muscles? ;) I've got to do mine soon., also.
>
> Should have typed that better. It was $190 for labor and $60
> for the part. Had to swallow the $60+tax since (stupid me) didn't
> order it with the other parts. Normally I would have got it from
> these folks http://www.chryslerpartsdirect.com/ for $44 and shipping.
>
> I wrench sober. Like my beer, but history proves several cans
> and vehicle maintenance don't mix well. In this case I had to
> brace against the jeep to keep from dragging myself in circles.
> When it broke loose I darn near ate the wrench. Beer reaction time
> would have equaled a nice welt on mah noggin. :)
>
> Should have a website writeup on the process soonish. Other things
> are keeping me busy now.. (like attic insulation) yay.. cough.. yay..
>
> --
> DougW
>
11-26-2004, 06:47 PM
#10
Guest
Posts: n/a
Re: Tranny mount done :)
sounds good :) Thanks, I'll wait for the writeup... our 'newer' has has a
finished attic, so no more need of replacing/installing for insulation... I
wear it well......... ;0
Paul
"DougW" <post.replies@invalid.address> wrote in message
news:e_Opd.102413$tU4.41514@okepread06...
> Paw did pass the time by typing:
>> 190 for the tranny mount? wow.. now was that a 4' cheater bar sober or
>> w/
>> beer muscles? ;) I've got to do mine soon., also.
>
> Should have typed that better. It was $190 for labor and $60
> for the part. Had to swallow the $60+tax since (stupid me) didn't
> order it with the other parts. Normally I would have got it from
> these folks http://www.chryslerpartsdirect.com/ for $44 and shipping.
>
> I wrench sober. Like my beer, but history proves several cans
> and vehicle maintenance don't mix well. In this case I had to
> brace against the jeep to keep from dragging myself in circles.
> When it broke loose I darn near ate the wrench. Beer reaction time
> would have equaled a nice welt on mah noggin. :)
>
> Should have a website writeup on the process soonish. Other things
> are keeping me busy now.. (like attic insulation) yay.. cough.. yay..
>
> --
> DougW
>
finished attic, so no more need of replacing/installing for insulation... I
wear it well......... ;0
Paul
"DougW" <post.replies@invalid.address> wrote in message
news:e_Opd.102413$tU4.41514@okepread06...
> Paw did pass the time by typing:
>> 190 for the tranny mount? wow.. now was that a 4' cheater bar sober or
>> w/
>> beer muscles? ;) I've got to do mine soon., also.
>
> Should have typed that better. It was $190 for labor and $60
> for the part. Had to swallow the $60+tax since (stupid me) didn't
> order it with the other parts. Normally I would have got it from
> these folks http://www.chryslerpartsdirect.com/ for $44 and shipping.
>
> I wrench sober. Like my beer, but history proves several cans
> and vehicle maintenance don't mix well. In this case I had to
> brace against the jeep to keep from dragging myself in circles.
> When it broke loose I darn near ate the wrench. Beer reaction time
> would have equaled a nice welt on mah noggin. :)
>
> Should have a website writeup on the process soonish. Other things
> are keeping me busy now.. (like attic insulation) yay.. cough.. yay..
>
> --
> DougW
>