Need torque verification
#1
Guest
Posts: n/a
Need torque verification
I have checked two books now and each book says that the big nut on the hub
assembly for a 1988 Jeep Wrangler gets torqued to 175 foot pounds. Is this
correct? Is there a crush sleeve inside this hub assembly that I do not know
about. The reason I ask is that first I find it unbelievable and two is my
torque wrench only goes to 150 foot pounds. Please advise
Thanks
assembly for a 1988 Jeep Wrangler gets torqued to 175 foot pounds. Is this
correct? Is there a crush sleeve inside this hub assembly that I do not know
about. The reason I ask is that first I find it unbelievable and two is my
torque wrench only goes to 150 foot pounds. Please advise
Thanks
#2
Guest
Posts: n/a
Re: Need torque verification
Hows this so unbelievable??
The lugs on your rims are supposed to be torqued from 80-100 foot pounds or
something (bill??).
If you are thinking that this is a lot cuz you think of lifting 150pounds as
a hard task...well, it's called torque not force. With a 2foot handle on
your wrench it takes a rather small amount of force on your end to create
150pounds on the nut/hub end.
I was working on some heavy equipment and had to torque down some bolts to
250. I'm thinkin...wait, I'm 250....do I have to do a chin-up?
nope....with a cheater bar I did it one handed! Very easy!
"nvrpc" <nvrpc@microsoft.com> wrote in message
news:1086ehkt9ddkr69@corp.supernews.com...
> I have checked two books now and each book says that the big nut on the
hub
> assembly for a 1988 Jeep Wrangler gets torqued to 175 foot pounds. Is this
> correct? Is there a crush sleeve inside this hub assembly that I do not
know
> about. The reason I ask is that first I find it unbelievable and two is my
> torque wrench only goes to 150 foot pounds. Please advise
>
> Thanks
>
>
The lugs on your rims are supposed to be torqued from 80-100 foot pounds or
something (bill??).
If you are thinking that this is a lot cuz you think of lifting 150pounds as
a hard task...well, it's called torque not force. With a 2foot handle on
your wrench it takes a rather small amount of force on your end to create
150pounds on the nut/hub end.
I was working on some heavy equipment and had to torque down some bolts to
250. I'm thinkin...wait, I'm 250....do I have to do a chin-up?
nope....with a cheater bar I did it one handed! Very easy!
"nvrpc" <nvrpc@microsoft.com> wrote in message
news:1086ehkt9ddkr69@corp.supernews.com...
> I have checked two books now and each book says that the big nut on the
hub
> assembly for a 1988 Jeep Wrangler gets torqued to 175 foot pounds. Is this
> correct? Is there a crush sleeve inside this hub assembly that I do not
know
> about. The reason I ask is that first I find it unbelievable and two is my
> torque wrench only goes to 150 foot pounds. Please advise
>
> Thanks
>
>
#3
Guest
Posts: n/a
Re: Need torque verification
Hows this so unbelievable??
The lugs on your rims are supposed to be torqued from 80-100 foot pounds or
something (bill??).
If you are thinking that this is a lot cuz you think of lifting 150pounds as
a hard task...well, it's called torque not force. With a 2foot handle on
your wrench it takes a rather small amount of force on your end to create
150pounds on the nut/hub end.
I was working on some heavy equipment and had to torque down some bolts to
250. I'm thinkin...wait, I'm 250....do I have to do a chin-up?
nope....with a cheater bar I did it one handed! Very easy!
"nvrpc" <nvrpc@microsoft.com> wrote in message
news:1086ehkt9ddkr69@corp.supernews.com...
> I have checked two books now and each book says that the big nut on the
hub
> assembly for a 1988 Jeep Wrangler gets torqued to 175 foot pounds. Is this
> correct? Is there a crush sleeve inside this hub assembly that I do not
know
> about. The reason I ask is that first I find it unbelievable and two is my
> torque wrench only goes to 150 foot pounds. Please advise
>
> Thanks
>
>
The lugs on your rims are supposed to be torqued from 80-100 foot pounds or
something (bill??).
If you are thinking that this is a lot cuz you think of lifting 150pounds as
a hard task...well, it's called torque not force. With a 2foot handle on
your wrench it takes a rather small amount of force on your end to create
150pounds on the nut/hub end.
I was working on some heavy equipment and had to torque down some bolts to
250. I'm thinkin...wait, I'm 250....do I have to do a chin-up?
nope....with a cheater bar I did it one handed! Very easy!
"nvrpc" <nvrpc@microsoft.com> wrote in message
news:1086ehkt9ddkr69@corp.supernews.com...
> I have checked two books now and each book says that the big nut on the
hub
> assembly for a 1988 Jeep Wrangler gets torqued to 175 foot pounds. Is this
> correct? Is there a crush sleeve inside this hub assembly that I do not
know
> about. The reason I ask is that first I find it unbelievable and two is my
> torque wrench only goes to 150 foot pounds. Please advise
>
> Thanks
>
>
#4
Guest
Posts: n/a
Re: Need torque verification
Hows this so unbelievable??
The lugs on your rims are supposed to be torqued from 80-100 foot pounds or
something (bill??).
If you are thinking that this is a lot cuz you think of lifting 150pounds as
a hard task...well, it's called torque not force. With a 2foot handle on
your wrench it takes a rather small amount of force on your end to create
150pounds on the nut/hub end.
I was working on some heavy equipment and had to torque down some bolts to
250. I'm thinkin...wait, I'm 250....do I have to do a chin-up?
nope....with a cheater bar I did it one handed! Very easy!
"nvrpc" <nvrpc@microsoft.com> wrote in message
news:1086ehkt9ddkr69@corp.supernews.com...
> I have checked two books now and each book says that the big nut on the
hub
> assembly for a 1988 Jeep Wrangler gets torqued to 175 foot pounds. Is this
> correct? Is there a crush sleeve inside this hub assembly that I do not
know
> about. The reason I ask is that first I find it unbelievable and two is my
> torque wrench only goes to 150 foot pounds. Please advise
>
> Thanks
>
>
The lugs on your rims are supposed to be torqued from 80-100 foot pounds or
something (bill??).
If you are thinking that this is a lot cuz you think of lifting 150pounds as
a hard task...well, it's called torque not force. With a 2foot handle on
your wrench it takes a rather small amount of force on your end to create
150pounds on the nut/hub end.
I was working on some heavy equipment and had to torque down some bolts to
250. I'm thinkin...wait, I'm 250....do I have to do a chin-up?
nope....with a cheater bar I did it one handed! Very easy!
"nvrpc" <nvrpc@microsoft.com> wrote in message
news:1086ehkt9ddkr69@corp.supernews.com...
> I have checked two books now and each book says that the big nut on the
hub
> assembly for a 1988 Jeep Wrangler gets torqued to 175 foot pounds. Is this
> correct? Is there a crush sleeve inside this hub assembly that I do not
know
> about. The reason I ask is that first I find it unbelievable and two is my
> torque wrench only goes to 150 foot pounds. Please advise
>
> Thanks
>
>
#5
Guest
Posts: n/a
Re: Need torque verification
Hows this so unbelievable??
The lugs on your rims are supposed to be torqued from 80-100 foot pounds or
something (bill??).
If you are thinking that this is a lot cuz you think of lifting 150pounds as
a hard task...well, it's called torque not force. With a 2foot handle on
your wrench it takes a rather small amount of force on your end to create
150pounds on the nut/hub end.
I was working on some heavy equipment and had to torque down some bolts to
250. I'm thinkin...wait, I'm 250....do I have to do a chin-up?
nope....with a cheater bar I did it one handed! Very easy!
"nvrpc" <nvrpc@microsoft.com> wrote in message
news:1086ehkt9ddkr69@corp.supernews.com...
> I have checked two books now and each book says that the big nut on the
hub
> assembly for a 1988 Jeep Wrangler gets torqued to 175 foot pounds. Is this
> correct? Is there a crush sleeve inside this hub assembly that I do not
know
> about. The reason I ask is that first I find it unbelievable and two is my
> torque wrench only goes to 150 foot pounds. Please advise
>
> Thanks
>
>
The lugs on your rims are supposed to be torqued from 80-100 foot pounds or
something (bill??).
If you are thinking that this is a lot cuz you think of lifting 150pounds as
a hard task...well, it's called torque not force. With a 2foot handle on
your wrench it takes a rather small amount of force on your end to create
150pounds on the nut/hub end.
I was working on some heavy equipment and had to torque down some bolts to
250. I'm thinkin...wait, I'm 250....do I have to do a chin-up?
nope....with a cheater bar I did it one handed! Very easy!
"nvrpc" <nvrpc@microsoft.com> wrote in message
news:1086ehkt9ddkr69@corp.supernews.com...
> I have checked two books now and each book says that the big nut on the
hub
> assembly for a 1988 Jeep Wrangler gets torqued to 175 foot pounds. Is this
> correct? Is there a crush sleeve inside this hub assembly that I do not
know
> about. The reason I ask is that first I find it unbelievable and two is my
> torque wrench only goes to 150 foot pounds. Please advise
>
> Thanks
>
>
#6
Guest
Posts: n/a
Re: Need torque verification
I am just thinking about the force of the roller bearing onto the race face.
To me this 175 foot pounds that the book calls for is a lot more then that
used on the Timken bearing on the spindle of an old Chevy drum break
assembly. As a matter of a fact they only had a 25 inch pound torque
requirement, so for me I see 175 foot pounds as a lot of pre load on two
roller bearing. I can only suspect that inside this assembly must be a
precision ground spacer that is actually sharing the load. Does anyone know?
"SB" <chicbearsmook@hotmail.com> wrote in message
news:j5Hgc.10822$9kJ.1219@news04.bloor.is.net.cabl e.rogers.com...
> Hows this so unbelievable??
>
> The lugs on your rims are supposed to be torqued from 80-100 foot pounds
or
> something (bill??).
>
> If you are thinking that this is a lot cuz you think of lifting 150pounds
as
> a hard task...well, it's called torque not force. With a 2foot handle on
> your wrench it takes a rather small amount of force on your end to create
> 150pounds on the nut/hub end.
>
> I was working on some heavy equipment and had to torque down some bolts to
> 250. I'm thinkin...wait, I'm 250....do I have to do a chin-up?
> nope....with a cheater bar I did it one handed! Very easy!
>
>
>
> "nvrpc" <nvrpc@microsoft.com> wrote in message
> news:1086ehkt9ddkr69@corp.supernews.com...
> > I have checked two books now and each book says that the big nut on the
> hub
> > assembly for a 1988 Jeep Wrangler gets torqued to 175 foot pounds. Is
this
> > correct? Is there a crush sleeve inside this hub assembly that I do not
> know
> > about. The reason I ask is that first I find it unbelievable and two is
my
> > torque wrench only goes to 150 foot pounds. Please advise
> >
> > Thanks
> >
> >
>
>
To me this 175 foot pounds that the book calls for is a lot more then that
used on the Timken bearing on the spindle of an old Chevy drum break
assembly. As a matter of a fact they only had a 25 inch pound torque
requirement, so for me I see 175 foot pounds as a lot of pre load on two
roller bearing. I can only suspect that inside this assembly must be a
precision ground spacer that is actually sharing the load. Does anyone know?
"SB" <chicbearsmook@hotmail.com> wrote in message
news:j5Hgc.10822$9kJ.1219@news04.bloor.is.net.cabl e.rogers.com...
> Hows this so unbelievable??
>
> The lugs on your rims are supposed to be torqued from 80-100 foot pounds
or
> something (bill??).
>
> If you are thinking that this is a lot cuz you think of lifting 150pounds
as
> a hard task...well, it's called torque not force. With a 2foot handle on
> your wrench it takes a rather small amount of force on your end to create
> 150pounds on the nut/hub end.
>
> I was working on some heavy equipment and had to torque down some bolts to
> 250. I'm thinkin...wait, I'm 250....do I have to do a chin-up?
> nope....with a cheater bar I did it one handed! Very easy!
>
>
>
> "nvrpc" <nvrpc@microsoft.com> wrote in message
> news:1086ehkt9ddkr69@corp.supernews.com...
> > I have checked two books now and each book says that the big nut on the
> hub
> > assembly for a 1988 Jeep Wrangler gets torqued to 175 foot pounds. Is
this
> > correct? Is there a crush sleeve inside this hub assembly that I do not
> know
> > about. The reason I ask is that first I find it unbelievable and two is
my
> > torque wrench only goes to 150 foot pounds. Please advise
> >
> > Thanks
> >
> >
>
>
#7
Guest
Posts: n/a
Re: Need torque verification
I am just thinking about the force of the roller bearing onto the race face.
To me this 175 foot pounds that the book calls for is a lot more then that
used on the Timken bearing on the spindle of an old Chevy drum break
assembly. As a matter of a fact they only had a 25 inch pound torque
requirement, so for me I see 175 foot pounds as a lot of pre load on two
roller bearing. I can only suspect that inside this assembly must be a
precision ground spacer that is actually sharing the load. Does anyone know?
"SB" <chicbearsmook@hotmail.com> wrote in message
news:j5Hgc.10822$9kJ.1219@news04.bloor.is.net.cabl e.rogers.com...
> Hows this so unbelievable??
>
> The lugs on your rims are supposed to be torqued from 80-100 foot pounds
or
> something (bill??).
>
> If you are thinking that this is a lot cuz you think of lifting 150pounds
as
> a hard task...well, it's called torque not force. With a 2foot handle on
> your wrench it takes a rather small amount of force on your end to create
> 150pounds on the nut/hub end.
>
> I was working on some heavy equipment and had to torque down some bolts to
> 250. I'm thinkin...wait, I'm 250....do I have to do a chin-up?
> nope....with a cheater bar I did it one handed! Very easy!
>
>
>
> "nvrpc" <nvrpc@microsoft.com> wrote in message
> news:1086ehkt9ddkr69@corp.supernews.com...
> > I have checked two books now and each book says that the big nut on the
> hub
> > assembly for a 1988 Jeep Wrangler gets torqued to 175 foot pounds. Is
this
> > correct? Is there a crush sleeve inside this hub assembly that I do not
> know
> > about. The reason I ask is that first I find it unbelievable and two is
my
> > torque wrench only goes to 150 foot pounds. Please advise
> >
> > Thanks
> >
> >
>
>
To me this 175 foot pounds that the book calls for is a lot more then that
used on the Timken bearing on the spindle of an old Chevy drum break
assembly. As a matter of a fact they only had a 25 inch pound torque
requirement, so for me I see 175 foot pounds as a lot of pre load on two
roller bearing. I can only suspect that inside this assembly must be a
precision ground spacer that is actually sharing the load. Does anyone know?
"SB" <chicbearsmook@hotmail.com> wrote in message
news:j5Hgc.10822$9kJ.1219@news04.bloor.is.net.cabl e.rogers.com...
> Hows this so unbelievable??
>
> The lugs on your rims are supposed to be torqued from 80-100 foot pounds
or
> something (bill??).
>
> If you are thinking that this is a lot cuz you think of lifting 150pounds
as
> a hard task...well, it's called torque not force. With a 2foot handle on
> your wrench it takes a rather small amount of force on your end to create
> 150pounds on the nut/hub end.
>
> I was working on some heavy equipment and had to torque down some bolts to
> 250. I'm thinkin...wait, I'm 250....do I have to do a chin-up?
> nope....with a cheater bar I did it one handed! Very easy!
>
>
>
> "nvrpc" <nvrpc@microsoft.com> wrote in message
> news:1086ehkt9ddkr69@corp.supernews.com...
> > I have checked two books now and each book says that the big nut on the
> hub
> > assembly for a 1988 Jeep Wrangler gets torqued to 175 foot pounds. Is
this
> > correct? Is there a crush sleeve inside this hub assembly that I do not
> know
> > about. The reason I ask is that first I find it unbelievable and two is
my
> > torque wrench only goes to 150 foot pounds. Please advise
> >
> > Thanks
> >
> >
>
>
#8
Guest
Posts: n/a
Re: Need torque verification
I am just thinking about the force of the roller bearing onto the race face.
To me this 175 foot pounds that the book calls for is a lot more then that
used on the Timken bearing on the spindle of an old Chevy drum break
assembly. As a matter of a fact they only had a 25 inch pound torque
requirement, so for me I see 175 foot pounds as a lot of pre load on two
roller bearing. I can only suspect that inside this assembly must be a
precision ground spacer that is actually sharing the load. Does anyone know?
"SB" <chicbearsmook@hotmail.com> wrote in message
news:j5Hgc.10822$9kJ.1219@news04.bloor.is.net.cabl e.rogers.com...
> Hows this so unbelievable??
>
> The lugs on your rims are supposed to be torqued from 80-100 foot pounds
or
> something (bill??).
>
> If you are thinking that this is a lot cuz you think of lifting 150pounds
as
> a hard task...well, it's called torque not force. With a 2foot handle on
> your wrench it takes a rather small amount of force on your end to create
> 150pounds on the nut/hub end.
>
> I was working on some heavy equipment and had to torque down some bolts to
> 250. I'm thinkin...wait, I'm 250....do I have to do a chin-up?
> nope....with a cheater bar I did it one handed! Very easy!
>
>
>
> "nvrpc" <nvrpc@microsoft.com> wrote in message
> news:1086ehkt9ddkr69@corp.supernews.com...
> > I have checked two books now and each book says that the big nut on the
> hub
> > assembly for a 1988 Jeep Wrangler gets torqued to 175 foot pounds. Is
this
> > correct? Is there a crush sleeve inside this hub assembly that I do not
> know
> > about. The reason I ask is that first I find it unbelievable and two is
my
> > torque wrench only goes to 150 foot pounds. Please advise
> >
> > Thanks
> >
> >
>
>
To me this 175 foot pounds that the book calls for is a lot more then that
used on the Timken bearing on the spindle of an old Chevy drum break
assembly. As a matter of a fact they only had a 25 inch pound torque
requirement, so for me I see 175 foot pounds as a lot of pre load on two
roller bearing. I can only suspect that inside this assembly must be a
precision ground spacer that is actually sharing the load. Does anyone know?
"SB" <chicbearsmook@hotmail.com> wrote in message
news:j5Hgc.10822$9kJ.1219@news04.bloor.is.net.cabl e.rogers.com...
> Hows this so unbelievable??
>
> The lugs on your rims are supposed to be torqued from 80-100 foot pounds
or
> something (bill??).
>
> If you are thinking that this is a lot cuz you think of lifting 150pounds
as
> a hard task...well, it's called torque not force. With a 2foot handle on
> your wrench it takes a rather small amount of force on your end to create
> 150pounds on the nut/hub end.
>
> I was working on some heavy equipment and had to torque down some bolts to
> 250. I'm thinkin...wait, I'm 250....do I have to do a chin-up?
> nope....with a cheater bar I did it one handed! Very easy!
>
>
>
> "nvrpc" <nvrpc@microsoft.com> wrote in message
> news:1086ehkt9ddkr69@corp.supernews.com...
> > I have checked two books now and each book says that the big nut on the
> hub
> > assembly for a 1988 Jeep Wrangler gets torqued to 175 foot pounds. Is
this
> > correct? Is there a crush sleeve inside this hub assembly that I do not
> know
> > about. The reason I ask is that first I find it unbelievable and two is
my
> > torque wrench only goes to 150 foot pounds. Please advise
> >
> > Thanks
> >
> >
>
>
#9
Guest
Posts: n/a
Re: Need torque verification
I am just thinking about the force of the roller bearing onto the race face.
To me this 175 foot pounds that the book calls for is a lot more then that
used on the Timken bearing on the spindle of an old Chevy drum break
assembly. As a matter of a fact they only had a 25 inch pound torque
requirement, so for me I see 175 foot pounds as a lot of pre load on two
roller bearing. I can only suspect that inside this assembly must be a
precision ground spacer that is actually sharing the load. Does anyone know?
"SB" <chicbearsmook@hotmail.com> wrote in message
news:j5Hgc.10822$9kJ.1219@news04.bloor.is.net.cabl e.rogers.com...
> Hows this so unbelievable??
>
> The lugs on your rims are supposed to be torqued from 80-100 foot pounds
or
> something (bill??).
>
> If you are thinking that this is a lot cuz you think of lifting 150pounds
as
> a hard task...well, it's called torque not force. With a 2foot handle on
> your wrench it takes a rather small amount of force on your end to create
> 150pounds on the nut/hub end.
>
> I was working on some heavy equipment and had to torque down some bolts to
> 250. I'm thinkin...wait, I'm 250....do I have to do a chin-up?
> nope....with a cheater bar I did it one handed! Very easy!
>
>
>
> "nvrpc" <nvrpc@microsoft.com> wrote in message
> news:1086ehkt9ddkr69@corp.supernews.com...
> > I have checked two books now and each book says that the big nut on the
> hub
> > assembly for a 1988 Jeep Wrangler gets torqued to 175 foot pounds. Is
this
> > correct? Is there a crush sleeve inside this hub assembly that I do not
> know
> > about. The reason I ask is that first I find it unbelievable and two is
my
> > torque wrench only goes to 150 foot pounds. Please advise
> >
> > Thanks
> >
> >
>
>
To me this 175 foot pounds that the book calls for is a lot more then that
used on the Timken bearing on the spindle of an old Chevy drum break
assembly. As a matter of a fact they only had a 25 inch pound torque
requirement, so for me I see 175 foot pounds as a lot of pre load on two
roller bearing. I can only suspect that inside this assembly must be a
precision ground spacer that is actually sharing the load. Does anyone know?
"SB" <chicbearsmook@hotmail.com> wrote in message
news:j5Hgc.10822$9kJ.1219@news04.bloor.is.net.cabl e.rogers.com...
> Hows this so unbelievable??
>
> The lugs on your rims are supposed to be torqued from 80-100 foot pounds
or
> something (bill??).
>
> If you are thinking that this is a lot cuz you think of lifting 150pounds
as
> a hard task...well, it's called torque not force. With a 2foot handle on
> your wrench it takes a rather small amount of force on your end to create
> 150pounds on the nut/hub end.
>
> I was working on some heavy equipment and had to torque down some bolts to
> 250. I'm thinkin...wait, I'm 250....do I have to do a chin-up?
> nope....with a cheater bar I did it one handed! Very easy!
>
>
>
> "nvrpc" <nvrpc@microsoft.com> wrote in message
> news:1086ehkt9ddkr69@corp.supernews.com...
> > I have checked two books now and each book says that the big nut on the
> hub
> > assembly for a 1988 Jeep Wrangler gets torqued to 175 foot pounds. Is
this
> > correct? Is there a crush sleeve inside this hub assembly that I do not
> know
> > about. The reason I ask is that first I find it unbelievable and two is
my
> > torque wrench only goes to 150 foot pounds. Please advise
> >
> > Thanks
> >
> >
>
>
#10
Guest
Posts: n/a
Re: Need torque verification
The axle nut has nothing to with the ball bears setup they are
pressed on to the pipe thingie you call a hub and all you're doing is
securing the axle to it, just like these little front wheel drive rice
burners: http://www.----------.com/Dana30hub.jpg
God Bless America, ßill O|||||||O
mailto:--------------------
nvrpc wrote:
>
> I am just thinking about the force of the roller bearing onto the race face.
> To me this 175 foot pounds that the book calls for is a lot more then that
> used on the Timken bearing on the spindle of an old Chevy drum break
> assembly. As a matter of a fact they only had a 25 inch pound torque
> requirement, so for me I see 175 foot pounds as a lot of pre load on two
> roller bearing. I can only suspect that inside this assembly must be a
> precision ground spacer that is actually sharing the load. Does anyone know?
>
> "SB" <chicbearsmook@hotmail.com> wrote in message
> news:j5Hgc.10822$9kJ.1219@news04.bloor.is.net.cabl e.rogers.com...
> > Hows this so unbelievable??
> >
> > The lugs on your rims are supposed to be torqued from 80-100 foot pounds
> or
> > something (bill??).
> >
> > If you are thinking that this is a lot cuz you think of lifting 150pounds
> as
> > a hard task...well, it's called torque not force. With a 2foot handle on
> > your wrench it takes a rather small amount of force on your end to create
> > 150pounds on the nut/hub end.
> >
> > I was working on some heavy equipment and had to torque down some bolts to
> > 250. I'm thinkin...wait, I'm 250....do I have to do a chin-up?
> > nope....with a cheater bar I did it one handed! Very easy!
> >
> >
> >
> > "nvrpc" <nvrpc@microsoft.com> wrote in message
> > news:1086ehkt9ddkr69@corp.supernews.com...
> > > I have checked two books now and each book says that the big nut on the
> > hub
> > > assembly for a 1988 Jeep Wrangler gets torqued to 175 foot pounds. Is
> this
> > > correct? Is there a crush sleeve inside this hub assembly that I do not
> > know
> > > about. The reason I ask is that first I find it unbelievable and two is
> my
> > > torque wrench only goes to 150 foot pounds. Please advise
> > >
> > > Thanks
> > >
> > >
> >
> >
pressed on to the pipe thingie you call a hub and all you're doing is
securing the axle to it, just like these little front wheel drive rice
burners: http://www.----------.com/Dana30hub.jpg
God Bless America, ßill O|||||||O
mailto:--------------------
nvrpc wrote:
>
> I am just thinking about the force of the roller bearing onto the race face.
> To me this 175 foot pounds that the book calls for is a lot more then that
> used on the Timken bearing on the spindle of an old Chevy drum break
> assembly. As a matter of a fact they only had a 25 inch pound torque
> requirement, so for me I see 175 foot pounds as a lot of pre load on two
> roller bearing. I can only suspect that inside this assembly must be a
> precision ground spacer that is actually sharing the load. Does anyone know?
>
> "SB" <chicbearsmook@hotmail.com> wrote in message
> news:j5Hgc.10822$9kJ.1219@news04.bloor.is.net.cabl e.rogers.com...
> > Hows this so unbelievable??
> >
> > The lugs on your rims are supposed to be torqued from 80-100 foot pounds
> or
> > something (bill??).
> >
> > If you are thinking that this is a lot cuz you think of lifting 150pounds
> as
> > a hard task...well, it's called torque not force. With a 2foot handle on
> > your wrench it takes a rather small amount of force on your end to create
> > 150pounds on the nut/hub end.
> >
> > I was working on some heavy equipment and had to torque down some bolts to
> > 250. I'm thinkin...wait, I'm 250....do I have to do a chin-up?
> > nope....with a cheater bar I did it one handed! Very easy!
> >
> >
> >
> > "nvrpc" <nvrpc@microsoft.com> wrote in message
> > news:1086ehkt9ddkr69@corp.supernews.com...
> > > I have checked two books now and each book says that the big nut on the
> > hub
> > > assembly for a 1988 Jeep Wrangler gets torqued to 175 foot pounds. Is
> this
> > > correct? Is there a crush sleeve inside this hub assembly that I do not
> > know
> > > about. The reason I ask is that first I find it unbelievable and two is
> my
> > > torque wrench only goes to 150 foot pounds. Please advise
> > >
> > > Thanks
> > >
> > >
> >
> >