How to remove padded dash?
10-26-2003, 04:25 PM
#31
Guest
Posts: n/a
Re: Wiper wiring routing, help? WAS: How to remove padded dash?
;-)
There is an oval slot in the top of the cowl that the plug and harness
fit through just inboard of the front clamps. You have to lower the
windshield to get to it.
Mike
Lee Ayrton wrote:
>
> How does the wiper harness get behind the dash in the late 1970s CJs? I
> just reinstalled my windshield frame on my new steel CJ-5 tub, got the
> harness captured under a washer on the second screw over for the cowl
> rubber, but just can't remember how it gets to the switch. Is there
> supposed to be a hole in the cowl, or (as my vague memory suggests) does
> it simply get pinched between the dash and cowl?
>
> One again Mike Romain reads my mind and mentions something I've come to
> the group to ask:
>
> On or about Sat, 25 Oct 2003, Mike Romain of romainm@sympatico.ca wrote:
>
> > The wiring harness for the wiper motor could maybe be hanging up so the
> > windshield won't fold...
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > travis wrote:
> > >
> > > On Fri, 24 Oct 2003 18:09:31 GMT, "JimG" <jimg@cj7.com> shared the
> > > following:
> > >
> > > >You need to get that windshield to fold down. Are you sure it's not just
> > > >the gasket along the bottom sticking?
> > >
> > > I got the dash off. *cough cough* The window still won't fold down.
> > > *ahem* The hinges don't look rusted... the gasket isn't sticking...
> > > please just trust me on this. I'm going to take plead the 5th from
> > > here on out concerning my windshield. Let's just say that the padded
> > > dash is out now and the windshield is not going anywhere anytime soon.
> > > *cough cough*
> > >
> > > --
> > > Travis
> > > http://jeepadventures.dyndns.org/jeep.html
> > > The meek shall inherit the earth. After I'm finished with it.
> > > :wq!
> >
>
> --
> "doing whatever it took to capture world marketing shares, even as far
> as having multiple satellites circling the globe to ensure complete
> coverage and maximum profit potential."
>
> Tealady spills the beans on AFU's new business plan.
There is an oval slot in the top of the cowl that the plug and harness
fit through just inboard of the front clamps. You have to lower the
windshield to get to it.
Mike
Lee Ayrton wrote:
>
> How does the wiper harness get behind the dash in the late 1970s CJs? I
> just reinstalled my windshield frame on my new steel CJ-5 tub, got the
> harness captured under a washer on the second screw over for the cowl
> rubber, but just can't remember how it gets to the switch. Is there
> supposed to be a hole in the cowl, or (as my vague memory suggests) does
> it simply get pinched between the dash and cowl?
>
> One again Mike Romain reads my mind and mentions something I've come to
> the group to ask:
>
> On or about Sat, 25 Oct 2003, Mike Romain of romainm@sympatico.ca wrote:
>
> > The wiring harness for the wiper motor could maybe be hanging up so the
> > windshield won't fold...
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > travis wrote:
> > >
> > > On Fri, 24 Oct 2003 18:09:31 GMT, "JimG" <jimg@cj7.com> shared the
> > > following:
> > >
> > > >You need to get that windshield to fold down. Are you sure it's not just
> > > >the gasket along the bottom sticking?
> > >
> > > I got the dash off. *cough cough* The window still won't fold down.
> > > *ahem* The hinges don't look rusted... the gasket isn't sticking...
> > > please just trust me on this. I'm going to take plead the 5th from
> > > here on out concerning my windshield. Let's just say that the padded
> > > dash is out now and the windshield is not going anywhere anytime soon.
> > > *cough cough*
> > >
> > > --
> > > Travis
> > > http://jeepadventures.dyndns.org/jeep.html
> > > The meek shall inherit the earth. After I'm finished with it.
> > > :wq!
> >
>
> --
> "doing whatever it took to capture world marketing shares, even as far
> as having multiple satellites circling the globe to ensure complete
> coverage and maximum profit potential."
>
> Tealady spills the beans on AFU's new business plan.
10-28-2003, 08:03 AM
#32
Guest
Posts: n/a
Re: Wiper wiring routing, help? WAS: How to remove padded dash?
Arugh. Thanks. Any chance you could give me a couple of locating
measurements so I can cut the currently non-existing hole in it's rightful
place? Right n" from the side of the cowl, n" in from the dash? It is
one of the holes not made in my Replitub.
On the other hand the tub, grill, roll bar and windshield is on and bolted
down, the seats are in, the wiring is half done, the vacuum plumbing is
complete, and the new windshield glass was installed yesterday. Getting
close. I think I'll order a Sailcloth replace-a-top today.
Which brings me to my next problem: Anyone know of a source for a
drilling giude for the OEM top hardware? I've no holes or locations for
the top bow bracket, the door frame holes or all the snap locations.
Should be fun....
On or about Sun, 26 Oct 2003, Mike Romain of romainm@sympatico.ca wrote:
> ;-)
>
> There is an oval slot in the top of the cowl that the plug and harness
> fit through just inboard of the front clamps. You have to lower the
> windshield to get to it.
>
> Mike
>
> Lee Ayrton wrote:
> >
> > How does the wiper harness get behind the dash in the late 1970s CJs? I
> > just reinstalled my windshield frame on my new steel CJ-5 tub, got the
> > harness captured under a washer on the second screw over for the cowl
> > rubber, but just can't remember how it gets to the switch. Is there
> > supposed to be a hole in the cowl, or (as my vague memory suggests) does
> > it simply get pinched between the dash and cowl?
> >
> > One again Mike Romain reads my mind and mentions something I've come to
> > the group to ask:
> >
> > On or about Sat, 25 Oct 2003, Mike Romain of romainm@sympatico.ca wrote:
> >
> > > The wiring harness for the wiper motor could maybe be hanging up so the
> > > windshield won't fold...
> > >
> > > Mike
> > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > > 88 Cherokee 235 BFG AT's
> > >
> > > travis wrote:
> > > >
> > > > On Fri, 24 Oct 2003 18:09:31 GMT, "JimG" <jimg@cj7.com> shared the
> > > > following:
> > > >
> > > > >You need to get that windshield to fold down. Are you sure it's not just
> > > > >the gasket along the bottom sticking?
> > > >
> > > > I got the dash off. *cough cough* The window still won't fold down.
> > > > *ahem* The hinges don't look rusted... the gasket isn't sticking...
> > > > please just trust me on this. I'm going to take plead the 5th from
> > > > here on out concerning my windshield. Let's just say that the padded
> > > > dash is out now and the windshield is not going anywhere anytime soon.
> > > > *cough cough*
> > > >
> > > > --
> > > > Travis
> > > > http://jeepadventures.dyndns.org/jeep.html
> > > > The meek shall inherit the earth. After I'm finished with it.
> > > > :wq!
> > >
> >
> > --
> > "doing whatever it took to capture world marketing shares, even as far
> > as having multiple satellites circling the globe to ensure complete
> > coverage and maximum profit potential."
> >
> > Tealady spills the beans on AFU's new business plan.
>
--
"doing whatever it took to capture world marketing shares, even as far
as having multiple satellites circling the globe to ensure complete
coverage and maximum profit potential."
Tealady spills the beans on AFU's new business plan.
10-28-2003, 08:03 AM
#33
Guest
Posts: n/a
Re: Wiper wiring routing, help? WAS: How to remove padded dash?
Arugh. Thanks. Any chance you could give me a couple of locating
measurements so I can cut the currently non-existing hole in it's rightful
place? Right n" from the side of the cowl, n" in from the dash? It is
one of the holes not made in my Replitub.
On the other hand the tub, grill, roll bar and windshield is on and bolted
down, the seats are in, the wiring is half done, the vacuum plumbing is
complete, and the new windshield glass was installed yesterday. Getting
close. I think I'll order a Sailcloth replace-a-top today.
Which brings me to my next problem: Anyone know of a source for a
drilling giude for the OEM top hardware? I've no holes or locations for
the top bow bracket, the door frame holes or all the snap locations.
Should be fun....
On or about Sun, 26 Oct 2003, Mike Romain of romainm@sympatico.ca wrote:
> ;-)
>
> There is an oval slot in the top of the cowl that the plug and harness
> fit through just inboard of the front clamps. You have to lower the
> windshield to get to it.
>
> Mike
>
> Lee Ayrton wrote:
> >
> > How does the wiper harness get behind the dash in the late 1970s CJs? I
> > just reinstalled my windshield frame on my new steel CJ-5 tub, got the
> > harness captured under a washer on the second screw over for the cowl
> > rubber, but just can't remember how it gets to the switch. Is there
> > supposed to be a hole in the cowl, or (as my vague memory suggests) does
> > it simply get pinched between the dash and cowl?
> >
> > One again Mike Romain reads my mind and mentions something I've come to
> > the group to ask:
> >
> > On or about Sat, 25 Oct 2003, Mike Romain of romainm@sympatico.ca wrote:
> >
> > > The wiring harness for the wiper motor could maybe be hanging up so the
> > > windshield won't fold...
> > >
> > > Mike
> > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > > 88 Cherokee 235 BFG AT's
> > >
> > > travis wrote:
> > > >
> > > > On Fri, 24 Oct 2003 18:09:31 GMT, "JimG" <jimg@cj7.com> shared the
> > > > following:
> > > >
> > > > >You need to get that windshield to fold down. Are you sure it's not just
> > > > >the gasket along the bottom sticking?
> > > >
> > > > I got the dash off. *cough cough* The window still won't fold down.
> > > > *ahem* The hinges don't look rusted... the gasket isn't sticking...
> > > > please just trust me on this. I'm going to take plead the 5th from
> > > > here on out concerning my windshield. Let's just say that the padded
> > > > dash is out now and the windshield is not going anywhere anytime soon.
> > > > *cough cough*
> > > >
> > > > --
> > > > Travis
> > > > http://jeepadventures.dyndns.org/jeep.html
> > > > The meek shall inherit the earth. After I'm finished with it.
> > > > :wq!
> > >
> >
> > --
> > "doing whatever it took to capture world marketing shares, even as far
> > as having multiple satellites circling the globe to ensure complete
> > coverage and maximum profit potential."
> >
> > Tealady spills the beans on AFU's new business plan.
>
--
"doing whatever it took to capture world marketing shares, even as far
as having multiple satellites circling the globe to ensure complete
coverage and maximum profit potential."
Tealady spills the beans on AFU's new business plan.
10-28-2003, 08:03 AM
#34
Guest
Posts: n/a
Re: Wiper wiring routing, help? WAS: How to remove padded dash?
Arugh. Thanks. Any chance you could give me a couple of locating
measurements so I can cut the currently non-existing hole in it's rightful
place? Right n" from the side of the cowl, n" in from the dash? It is
one of the holes not made in my Replitub.
On the other hand the tub, grill, roll bar and windshield is on and bolted
down, the seats are in, the wiring is half done, the vacuum plumbing is
complete, and the new windshield glass was installed yesterday. Getting
close. I think I'll order a Sailcloth replace-a-top today.
Which brings me to my next problem: Anyone know of a source for a
drilling giude for the OEM top hardware? I've no holes or locations for
the top bow bracket, the door frame holes or all the snap locations.
Should be fun....
On or about Sun, 26 Oct 2003, Mike Romain of romainm@sympatico.ca wrote:
> ;-)
>
> There is an oval slot in the top of the cowl that the plug and harness
> fit through just inboard of the front clamps. You have to lower the
> windshield to get to it.
>
> Mike
>
> Lee Ayrton wrote:
> >
> > How does the wiper harness get behind the dash in the late 1970s CJs? I
> > just reinstalled my windshield frame on my new steel CJ-5 tub, got the
> > harness captured under a washer on the second screw over for the cowl
> > rubber, but just can't remember how it gets to the switch. Is there
> > supposed to be a hole in the cowl, or (as my vague memory suggests) does
> > it simply get pinched between the dash and cowl?
> >
> > One again Mike Romain reads my mind and mentions something I've come to
> > the group to ask:
> >
> > On or about Sat, 25 Oct 2003, Mike Romain of romainm@sympatico.ca wrote:
> >
> > > The wiring harness for the wiper motor could maybe be hanging up so the
> > > windshield won't fold...
> > >
> > > Mike
> > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > > 88 Cherokee 235 BFG AT's
> > >
> > > travis wrote:
> > > >
> > > > On Fri, 24 Oct 2003 18:09:31 GMT, "JimG" <jimg@cj7.com> shared the
> > > > following:
> > > >
> > > > >You need to get that windshield to fold down. Are you sure it's not just
> > > > >the gasket along the bottom sticking?
> > > >
> > > > I got the dash off. *cough cough* The window still won't fold down.
> > > > *ahem* The hinges don't look rusted... the gasket isn't sticking...
> > > > please just trust me on this. I'm going to take plead the 5th from
> > > > here on out concerning my windshield. Let's just say that the padded
> > > > dash is out now and the windshield is not going anywhere anytime soon.
> > > > *cough cough*
> > > >
> > > > --
> > > > Travis
> > > > http://jeepadventures.dyndns.org/jeep.html
> > > > The meek shall inherit the earth. After I'm finished with it.
> > > > :wq!
> > >
> >
> > --
> > "doing whatever it took to capture world marketing shares, even as far
> > as having multiple satellites circling the globe to ensure complete
> > coverage and maximum profit potential."
> >
> > Tealady spills the beans on AFU's new business plan.
>
--
"doing whatever it took to capture world marketing shares, even as far
as having multiple satellites circling the globe to ensure complete
coverage and maximum profit potential."
Tealady spills the beans on AFU's new business plan.
10-28-2003, 01:16 PM
#35
Guest
Posts: n/a
Re: Wiper wiring routing, help? WAS: How to remove padded dash?
From the outside of the tub under the hinge, it measures 4 1/4" to 5
1/2" and from the dash side of the tub 1" to 1 3/4"
Mike
Lee Ayrton wrote:
>
> Arugh. Thanks. Any chance you could give me a couple of locating
> measurements so I can cut the currently non-existing hole in it's rightful
> place? Right n" from the side of the cowl, n" in from the dash? It is
> one of the holes not made in my Replitub.
>
> On the other hand the tub, grill, roll bar and windshield is on and bolted
> down, the seats are in, the wiring is half done, the vacuum plumbing is
> complete, and the new windshield glass was installed yesterday. Getting
> close. I think I'll order a Sailcloth replace-a-top today.
>
> Which brings me to my next problem: Anyone know of a source for a
> drilling giude for the OEM top hardware? I've no holes or locations for
> the top bow bracket, the door frame holes or all the snap locations.
>
> Should be fun....
>
> On or about Sun, 26 Oct 2003, Mike Romain of romainm@sympatico.ca wrote:
>
> > ;-)
> >
> > There is an oval slot in the top of the cowl that the plug and harness
> > fit through just inboard of the front clamps. You have to lower the
> > windshield to get to it.
> >
> > Mike
> >
> > Lee Ayrton wrote:
> > >
> > > How does the wiper harness get behind the dash in the late 1970s CJs? I
> > > just reinstalled my windshield frame on my new steel CJ-5 tub, got the
> > > harness captured under a washer on the second screw over for the cowl
> > > rubber, but just can't remember how it gets to the switch. Is there
> > > supposed to be a hole in the cowl, or (as my vague memory suggests) does
> > > it simply get pinched between the dash and cowl?
> > >
> > > One again Mike Romain reads my mind and mentions something I've come to
> > > the group to ask:
> > >
> > > On or about Sat, 25 Oct 2003, Mike Romain of romainm@sympatico.ca wrote:
> > >
> > > > The wiring harness for the wiper motor could maybe be hanging up so the
> > > > windshield won't fold...
> > > >
> > > > Mike
> > > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > > > 88 Cherokee 235 BFG AT's
> > > >
> > > > travis wrote:
> > > > >
> > > > > On Fri, 24 Oct 2003 18:09:31 GMT, "JimG" <jimg@cj7.com> shared the
> > > > > following:
> > > > >
> > > > > >You need to get that windshield to fold down. Are you sure it's not just
> > > > > >the gasket along the bottom sticking?
> > > > >
> > > > > I got the dash off. *cough cough* The window still won't fold down.
> > > > > *ahem* The hinges don't look rusted... the gasket isn't sticking...
> > > > > please just trust me on this. I'm going to take plead the 5th from
> > > > > here on out concerning my windshield. Let's just say that the padded
> > > > > dash is out now and the windshield is not going anywhere anytime soon.
> > > > > *cough cough*
> > > > >
> > > > > --
> > > > > Travis
> > > > > http://jeepadventures.dyndns.org/jeep.html
> > > > > The meek shall inherit the earth. After I'm finished with it.
> > > > > :wq!
> > > >
> > >
> > > --
> > > "doing whatever it took to capture world marketing shares, even as far
> > > as having multiple satellites circling the globe to ensure complete
> > > coverage and maximum profit potential."
> > >
> > > Tealady spills the beans on AFU's new business plan.
> >
>
> --
> "doing whatever it took to capture world marketing shares, even as far
> as having multiple satellites circling the globe to ensure complete
> coverage and maximum profit potential."
>
> Tealady spills the beans on AFU's new business plan.
1/2" and from the dash side of the tub 1" to 1 3/4"
Mike
Lee Ayrton wrote:
>
> Arugh. Thanks. Any chance you could give me a couple of locating
> measurements so I can cut the currently non-existing hole in it's rightful
> place? Right n" from the side of the cowl, n" in from the dash? It is
> one of the holes not made in my Replitub.
>
> On the other hand the tub, grill, roll bar and windshield is on and bolted
> down, the seats are in, the wiring is half done, the vacuum plumbing is
> complete, and the new windshield glass was installed yesterday. Getting
> close. I think I'll order a Sailcloth replace-a-top today.
>
> Which brings me to my next problem: Anyone know of a source for a
> drilling giude for the OEM top hardware? I've no holes or locations for
> the top bow bracket, the door frame holes or all the snap locations.
>
> Should be fun....
>
> On or about Sun, 26 Oct 2003, Mike Romain of romainm@sympatico.ca wrote:
>
> > ;-)
> >
> > There is an oval slot in the top of the cowl that the plug and harness
> > fit through just inboard of the front clamps. You have to lower the
> > windshield to get to it.
> >
> > Mike
> >
> > Lee Ayrton wrote:
> > >
> > > How does the wiper harness get behind the dash in the late 1970s CJs? I
> > > just reinstalled my windshield frame on my new steel CJ-5 tub, got the
> > > harness captured under a washer on the second screw over for the cowl
> > > rubber, but just can't remember how it gets to the switch. Is there
> > > supposed to be a hole in the cowl, or (as my vague memory suggests) does
> > > it simply get pinched between the dash and cowl?
> > >
> > > One again Mike Romain reads my mind and mentions something I've come to
> > > the group to ask:
> > >
> > > On or about Sat, 25 Oct 2003, Mike Romain of romainm@sympatico.ca wrote:
> > >
> > > > The wiring harness for the wiper motor could maybe be hanging up so the
> > > > windshield won't fold...
> > > >
> > > > Mike
> > > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > > > 88 Cherokee 235 BFG AT's
> > > >
> > > > travis wrote:
> > > > >
> > > > > On Fri, 24 Oct 2003 18:09:31 GMT, "JimG" <jimg@cj7.com> shared the
> > > > > following:
> > > > >
> > > > > >You need to get that windshield to fold down. Are you sure it's not just
> > > > > >the gasket along the bottom sticking?
> > > > >
> > > > > I got the dash off. *cough cough* The window still won't fold down.
> > > > > *ahem* The hinges don't look rusted... the gasket isn't sticking...
> > > > > please just trust me on this. I'm going to take plead the 5th from
> > > > > here on out concerning my windshield. Let's just say that the padded
> > > > > dash is out now and the windshield is not going anywhere anytime soon.
> > > > > *cough cough*
> > > > >
> > > > > --
> > > > > Travis
> > > > > http://jeepadventures.dyndns.org/jeep.html
> > > > > The meek shall inherit the earth. After I'm finished with it.
> > > > > :wq!
> > > >
> > >
> > > --
> > > "doing whatever it took to capture world marketing shares, even as far
> > > as having multiple satellites circling the globe to ensure complete
> > > coverage and maximum profit potential."
> > >
> > > Tealady spills the beans on AFU's new business plan.
> >
>
> --
> "doing whatever it took to capture world marketing shares, even as far
> as having multiple satellites circling the globe to ensure complete
> coverage and maximum profit potential."
>
> Tealady spills the beans on AFU's new business plan.
10-28-2003, 01:16 PM
#36
Guest
Posts: n/a
Re: Wiper wiring routing, help? WAS: How to remove padded dash?
From the outside of the tub under the hinge, it measures 4 1/4" to 5
1/2" and from the dash side of the tub 1" to 1 3/4"
Mike
Lee Ayrton wrote:
>
> Arugh. Thanks. Any chance you could give me a couple of locating
> measurements so I can cut the currently non-existing hole in it's rightful
> place? Right n" from the side of the cowl, n" in from the dash? It is
> one of the holes not made in my Replitub.
>
> On the other hand the tub, grill, roll bar and windshield is on and bolted
> down, the seats are in, the wiring is half done, the vacuum plumbing is
> complete, and the new windshield glass was installed yesterday. Getting
> close. I think I'll order a Sailcloth replace-a-top today.
>
> Which brings me to my next problem: Anyone know of a source for a
> drilling giude for the OEM top hardware? I've no holes or locations for
> the top bow bracket, the door frame holes or all the snap locations.
>
> Should be fun....
>
> On or about Sun, 26 Oct 2003, Mike Romain of romainm@sympatico.ca wrote:
>
> > ;-)
> >
> > There is an oval slot in the top of the cowl that the plug and harness
> > fit through just inboard of the front clamps. You have to lower the
> > windshield to get to it.
> >
> > Mike
> >
> > Lee Ayrton wrote:
> > >
> > > How does the wiper harness get behind the dash in the late 1970s CJs? I
> > > just reinstalled my windshield frame on my new steel CJ-5 tub, got the
> > > harness captured under a washer on the second screw over for the cowl
> > > rubber, but just can't remember how it gets to the switch. Is there
> > > supposed to be a hole in the cowl, or (as my vague memory suggests) does
> > > it simply get pinched between the dash and cowl?
> > >
> > > One again Mike Romain reads my mind and mentions something I've come to
> > > the group to ask:
> > >
> > > On or about Sat, 25 Oct 2003, Mike Romain of romainm@sympatico.ca wrote:
> > >
> > > > The wiring harness for the wiper motor could maybe be hanging up so the
> > > > windshield won't fold...
> > > >
> > > > Mike
> > > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > > > 88 Cherokee 235 BFG AT's
> > > >
> > > > travis wrote:
> > > > >
> > > > > On Fri, 24 Oct 2003 18:09:31 GMT, "JimG" <jimg@cj7.com> shared the
> > > > > following:
> > > > >
> > > > > >You need to get that windshield to fold down. Are you sure it's not just
> > > > > >the gasket along the bottom sticking?
> > > > >
> > > > > I got the dash off. *cough cough* The window still won't fold down.
> > > > > *ahem* The hinges don't look rusted... the gasket isn't sticking...
> > > > > please just trust me on this. I'm going to take plead the 5th from
> > > > > here on out concerning my windshield. Let's just say that the padded
> > > > > dash is out now and the windshield is not going anywhere anytime soon.
> > > > > *cough cough*
> > > > >
> > > > > --
> > > > > Travis
> > > > > http://jeepadventures.dyndns.org/jeep.html
> > > > > The meek shall inherit the earth. After I'm finished with it.
> > > > > :wq!
> > > >
> > >
> > > --
> > > "doing whatever it took to capture world marketing shares, even as far
> > > as having multiple satellites circling the globe to ensure complete
> > > coverage and maximum profit potential."
> > >
> > > Tealady spills the beans on AFU's new business plan.
> >
>
> --
> "doing whatever it took to capture world marketing shares, even as far
> as having multiple satellites circling the globe to ensure complete
> coverage and maximum profit potential."
>
> Tealady spills the beans on AFU's new business plan.
1/2" and from the dash side of the tub 1" to 1 3/4"
Mike
Lee Ayrton wrote:
>
> Arugh. Thanks. Any chance you could give me a couple of locating
> measurements so I can cut the currently non-existing hole in it's rightful
> place? Right n" from the side of the cowl, n" in from the dash? It is
> one of the holes not made in my Replitub.
>
> On the other hand the tub, grill, roll bar and windshield is on and bolted
> down, the seats are in, the wiring is half done, the vacuum plumbing is
> complete, and the new windshield glass was installed yesterday. Getting
> close. I think I'll order a Sailcloth replace-a-top today.
>
> Which brings me to my next problem: Anyone know of a source for a
> drilling giude for the OEM top hardware? I've no holes or locations for
> the top bow bracket, the door frame holes or all the snap locations.
>
> Should be fun....
>
> On or about Sun, 26 Oct 2003, Mike Romain of romainm@sympatico.ca wrote:
>
> > ;-)
> >
> > There is an oval slot in the top of the cowl that the plug and harness
> > fit through just inboard of the front clamps. You have to lower the
> > windshield to get to it.
> >
> > Mike
> >
> > Lee Ayrton wrote:
> > >
> > > How does the wiper harness get behind the dash in the late 1970s CJs? I
> > > just reinstalled my windshield frame on my new steel CJ-5 tub, got the
> > > harness captured under a washer on the second screw over for the cowl
> > > rubber, but just can't remember how it gets to the switch. Is there
> > > supposed to be a hole in the cowl, or (as my vague memory suggests) does
> > > it simply get pinched between the dash and cowl?
> > >
> > > One again Mike Romain reads my mind and mentions something I've come to
> > > the group to ask:
> > >
> > > On or about Sat, 25 Oct 2003, Mike Romain of romainm@sympatico.ca wrote:
> > >
> > > > The wiring harness for the wiper motor could maybe be hanging up so the
> > > > windshield won't fold...
> > > >
> > > > Mike
> > > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > > > 88 Cherokee 235 BFG AT's
> > > >
> > > > travis wrote:
> > > > >
> > > > > On Fri, 24 Oct 2003 18:09:31 GMT, "JimG" <jimg@cj7.com> shared the
> > > > > following:
> > > > >
> > > > > >You need to get that windshield to fold down. Are you sure it's not just
> > > > > >the gasket along the bottom sticking?
> > > > >
> > > > > I got the dash off. *cough cough* The window still won't fold down.
> > > > > *ahem* The hinges don't look rusted... the gasket isn't sticking...
> > > > > please just trust me on this. I'm going to take plead the 5th from
> > > > > here on out concerning my windshield. Let's just say that the padded
> > > > > dash is out now and the windshield is not going anywhere anytime soon.
> > > > > *cough cough*
> > > > >
> > > > > --
> > > > > Travis
> > > > > http://jeepadventures.dyndns.org/jeep.html
> > > > > The meek shall inherit the earth. After I'm finished with it.
> > > > > :wq!
> > > >
> > >
> > > --
> > > "doing whatever it took to capture world marketing shares, even as far
> > > as having multiple satellites circling the globe to ensure complete
> > > coverage and maximum profit potential."
> > >
> > > Tealady spills the beans on AFU's new business plan.
> >
>
> --
> "doing whatever it took to capture world marketing shares, even as far
> as having multiple satellites circling the globe to ensure complete
> coverage and maximum profit potential."
>
> Tealady spills the beans on AFU's new business plan.
10-28-2003, 01:16 PM
#37
Guest
Posts: n/a
Re: Wiper wiring routing, help? WAS: How to remove padded dash?
From the outside of the tub under the hinge, it measures 4 1/4" to 5
1/2" and from the dash side of the tub 1" to 1 3/4"
Mike
Lee Ayrton wrote:
>
> Arugh. Thanks. Any chance you could give me a couple of locating
> measurements so I can cut the currently non-existing hole in it's rightful
> place? Right n" from the side of the cowl, n" in from the dash? It is
> one of the holes not made in my Replitub.
>
> On the other hand the tub, grill, roll bar and windshield is on and bolted
> down, the seats are in, the wiring is half done, the vacuum plumbing is
> complete, and the new windshield glass was installed yesterday. Getting
> close. I think I'll order a Sailcloth replace-a-top today.
>
> Which brings me to my next problem: Anyone know of a source for a
> drilling giude for the OEM top hardware? I've no holes or locations for
> the top bow bracket, the door frame holes or all the snap locations.
>
> Should be fun....
>
> On or about Sun, 26 Oct 2003, Mike Romain of romainm@sympatico.ca wrote:
>
> > ;-)
> >
> > There is an oval slot in the top of the cowl that the plug and harness
> > fit through just inboard of the front clamps. You have to lower the
> > windshield to get to it.
> >
> > Mike
> >
> > Lee Ayrton wrote:
> > >
> > > How does the wiper harness get behind the dash in the late 1970s CJs? I
> > > just reinstalled my windshield frame on my new steel CJ-5 tub, got the
> > > harness captured under a washer on the second screw over for the cowl
> > > rubber, but just can't remember how it gets to the switch. Is there
> > > supposed to be a hole in the cowl, or (as my vague memory suggests) does
> > > it simply get pinched between the dash and cowl?
> > >
> > > One again Mike Romain reads my mind and mentions something I've come to
> > > the group to ask:
> > >
> > > On or about Sat, 25 Oct 2003, Mike Romain of romainm@sympatico.ca wrote:
> > >
> > > > The wiring harness for the wiper motor could maybe be hanging up so the
> > > > windshield won't fold...
> > > >
> > > > Mike
> > > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > > > 88 Cherokee 235 BFG AT's
> > > >
> > > > travis wrote:
> > > > >
> > > > > On Fri, 24 Oct 2003 18:09:31 GMT, "JimG" <jimg@cj7.com> shared the
> > > > > following:
> > > > >
> > > > > >You need to get that windshield to fold down. Are you sure it's not just
> > > > > >the gasket along the bottom sticking?
> > > > >
> > > > > I got the dash off. *cough cough* The window still won't fold down.
> > > > > *ahem* The hinges don't look rusted... the gasket isn't sticking...
> > > > > please just trust me on this. I'm going to take plead the 5th from
> > > > > here on out concerning my windshield. Let's just say that the padded
> > > > > dash is out now and the windshield is not going anywhere anytime soon.
> > > > > *cough cough*
> > > > >
> > > > > --
> > > > > Travis
> > > > > http://jeepadventures.dyndns.org/jeep.html
> > > > > The meek shall inherit the earth. After I'm finished with it.
> > > > > :wq!
> > > >
> > >
> > > --
> > > "doing whatever it took to capture world marketing shares, even as far
> > > as having multiple satellites circling the globe to ensure complete
> > > coverage and maximum profit potential."
> > >
> > > Tealady spills the beans on AFU's new business plan.
> >
>
> --
> "doing whatever it took to capture world marketing shares, even as far
> as having multiple satellites circling the globe to ensure complete
> coverage and maximum profit potential."
>
> Tealady spills the beans on AFU's new business plan.
1/2" and from the dash side of the tub 1" to 1 3/4"
Mike
Lee Ayrton wrote:
>
> Arugh. Thanks. Any chance you could give me a couple of locating
> measurements so I can cut the currently non-existing hole in it's rightful
> place? Right n" from the side of the cowl, n" in from the dash? It is
> one of the holes not made in my Replitub.
>
> On the other hand the tub, grill, roll bar and windshield is on and bolted
> down, the seats are in, the wiring is half done, the vacuum plumbing is
> complete, and the new windshield glass was installed yesterday. Getting
> close. I think I'll order a Sailcloth replace-a-top today.
>
> Which brings me to my next problem: Anyone know of a source for a
> drilling giude for the OEM top hardware? I've no holes or locations for
> the top bow bracket, the door frame holes or all the snap locations.
>
> Should be fun....
>
> On or about Sun, 26 Oct 2003, Mike Romain of romainm@sympatico.ca wrote:
>
> > ;-)
> >
> > There is an oval slot in the top of the cowl that the plug and harness
> > fit through just inboard of the front clamps. You have to lower the
> > windshield to get to it.
> >
> > Mike
> >
> > Lee Ayrton wrote:
> > >
> > > How does the wiper harness get behind the dash in the late 1970s CJs? I
> > > just reinstalled my windshield frame on my new steel CJ-5 tub, got the
> > > harness captured under a washer on the second screw over for the cowl
> > > rubber, but just can't remember how it gets to the switch. Is there
> > > supposed to be a hole in the cowl, or (as my vague memory suggests) does
> > > it simply get pinched between the dash and cowl?
> > >
> > > One again Mike Romain reads my mind and mentions something I've come to
> > > the group to ask:
> > >
> > > On or about Sat, 25 Oct 2003, Mike Romain of romainm@sympatico.ca wrote:
> > >
> > > > The wiring harness for the wiper motor could maybe be hanging up so the
> > > > windshield won't fold...
> > > >
> > > > Mike
> > > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > > > 88 Cherokee 235 BFG AT's
> > > >
> > > > travis wrote:
> > > > >
> > > > > On Fri, 24 Oct 2003 18:09:31 GMT, "JimG" <jimg@cj7.com> shared the
> > > > > following:
> > > > >
> > > > > >You need to get that windshield to fold down. Are you sure it's not just
> > > > > >the gasket along the bottom sticking?
> > > > >
> > > > > I got the dash off. *cough cough* The window still won't fold down.
> > > > > *ahem* The hinges don't look rusted... the gasket isn't sticking...
> > > > > please just trust me on this. I'm going to take plead the 5th from
> > > > > here on out concerning my windshield. Let's just say that the padded
> > > > > dash is out now and the windshield is not going anywhere anytime soon.
> > > > > *cough cough*
> > > > >
> > > > > --
> > > > > Travis
> > > > > http://jeepadventures.dyndns.org/jeep.html
> > > > > The meek shall inherit the earth. After I'm finished with it.
> > > > > :wq!
> > > >
> > >
> > > --
> > > "doing whatever it took to capture world marketing shares, even as far
> > > as having multiple satellites circling the globe to ensure complete
> > > coverage and maximum profit potential."
> > >
> > > Tealady spills the beans on AFU's new business plan.
> >
>
> --
> "doing whatever it took to capture world marketing shares, even as far
> as having multiple satellites circling the globe to ensure complete
> coverage and maximum profit potential."
>
> Tealady spills the beans on AFU's new business plan.
Thread
Thread Starter
Forum
Replies
Last Post
Eric
Jeep Mailing List
15
08-04-2003 07:27 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)