Followup-- 2000 JGC V-8 still overheating
#361
Guest
Posts: n/a
Re: Followup-- 2000 JGC V-8 still overheating
On Thu, 18 Jan 2007 21:20:18 -0500, Mike Romain wrote:
> Earle Horton wrote:
>> "SnoMan" <admin@snoman.com> wrote in message
>> news:h270r25ousi635rk4tuu068hpk4s96lhn4@4ax.com...
>>> On Thu, 18 Jan 2007 16:56:58 -0500, Mike Romain <romainm@sympatico.ca>
>>> wrote:
>>>
>>>> I have seen fans get sucked into the rad when under water
>>>
>>> THe fan does not get sucked into it. Eaither the radiator moves toward
>>> it on impact of engine shifts forward but even then if you did not
>>> have a shoe horn fit with 1 inch or less fan clearance it would not
>>> happen. If you have 3 to 6 inches of clearance or more in there it
>>> will never happen unless you break something. Low engine driven fan
>>> to radiator clearance on a off road machine is not a wise setup in my
>>> book.
>>> -----------------
>>> TheSnoMan.com
>>
>> Mike would tear hell out of any shroud too with that fiberglass body he has.
>>
>> Earle
>>
>
> LOL!
>
> I have my rad hanging off two angle iron supports I welded to the frame
> rails. The shroud would have to have a frame of it's own.
>
> Having the rad held with 4 bolts causes the rad to snap in half because
> the frame rails flex so much because the 'glass body lets it. I have a
> one piece 'glass flip front. No structure at all in it, it is just a
> water cover...
>
> The side plates of the rad snap from the flex. I made my own side rails
> out of 1"x1/8" steel plate bar and welded it onto the stock sides. They
> stretched about 1/4". A bunch of my cores stretched and a couple
> snapped so I soldered them off.
>
> I now just hang my rad off two top bolts and let it swing side to side free.
>
> I was talking to a few other 'glass tub owners and apparently that is a
> common issue.
Take a look at your XJ - two bolts in the top, two fairly large pins on
the bottom that drop into holes with rubber grommets. AIR,the oles in the
cross member at the bottom are oval so that the bottom of the radiator can
slide, but that may just be my poor memory. That makes a lot more sense
than 4 solid mount bolts, especially under flex.
I agree with you about the flexible plastic blades. Mine have wear marks
on the front of the tips that have to be from hitting the radiator - the
fan I have has pretty flexible blades, so if you add any play at all in
the clutch you can easily get it into the radiator.
--
Will Honea <whonea@yahoo.com>
> Earle Horton wrote:
>> "SnoMan" <admin@snoman.com> wrote in message
>> news:h270r25ousi635rk4tuu068hpk4s96lhn4@4ax.com...
>>> On Thu, 18 Jan 2007 16:56:58 -0500, Mike Romain <romainm@sympatico.ca>
>>> wrote:
>>>
>>>> I have seen fans get sucked into the rad when under water
>>>
>>> THe fan does not get sucked into it. Eaither the radiator moves toward
>>> it on impact of engine shifts forward but even then if you did not
>>> have a shoe horn fit with 1 inch or less fan clearance it would not
>>> happen. If you have 3 to 6 inches of clearance or more in there it
>>> will never happen unless you break something. Low engine driven fan
>>> to radiator clearance on a off road machine is not a wise setup in my
>>> book.
>>> -----------------
>>> TheSnoMan.com
>>
>> Mike would tear hell out of any shroud too with that fiberglass body he has.
>>
>> Earle
>>
>
> LOL!
>
> I have my rad hanging off two angle iron supports I welded to the frame
> rails. The shroud would have to have a frame of it's own.
>
> Having the rad held with 4 bolts causes the rad to snap in half because
> the frame rails flex so much because the 'glass body lets it. I have a
> one piece 'glass flip front. No structure at all in it, it is just a
> water cover...
>
> The side plates of the rad snap from the flex. I made my own side rails
> out of 1"x1/8" steel plate bar and welded it onto the stock sides. They
> stretched about 1/4". A bunch of my cores stretched and a couple
> snapped so I soldered them off.
>
> I now just hang my rad off two top bolts and let it swing side to side free.
>
> I was talking to a few other 'glass tub owners and apparently that is a
> common issue.
Take a look at your XJ - two bolts in the top, two fairly large pins on
the bottom that drop into holes with rubber grommets. AIR,the oles in the
cross member at the bottom are oval so that the bottom of the radiator can
slide, but that may just be my poor memory. That makes a lot more sense
than 4 solid mount bolts, especially under flex.
I agree with you about the flexible plastic blades. Mine have wear marks
on the front of the tips that have to be from hitting the radiator - the
fan I have has pretty flexible blades, so if you add any play at all in
the clutch you can easily get it into the radiator.
--
Will Honea <whonea@yahoo.com>
#362
Guest
Posts: n/a
Re: Re: Followup-- 2000 JGC V-8 still overheating
On Thu, 18 Jan 2007 21:03:37 -0500, Mike Romain <romainm@sympatico.ca>
wrote:
>No no, the blades of the fan act like a propeller and try to pull water.
> The flex fan blades are not strong enough to do this so they get
>pulled forward instead of the water going backward because they are so
>flexible. This can make them tag the rad fins.
>
>Water is 'heavy'. Grab a flex fan blade and see how far you can hand
>bend it in a forward direction, then talk clearance....
I understand that but again if there was a lot of clearance it would
not happen and if proper flex fan was used the blades would flatten
out from water pressure (like with high air press at higher RPMs) and
not pull the water or bend toward radiator as blades would "give".
-----------------
TheSnoMan.com
wrote:
>No no, the blades of the fan act like a propeller and try to pull water.
> The flex fan blades are not strong enough to do this so they get
>pulled forward instead of the water going backward because they are so
>flexible. This can make them tag the rad fins.
>
>Water is 'heavy'. Grab a flex fan blade and see how far you can hand
>bend it in a forward direction, then talk clearance....
I understand that but again if there was a lot of clearance it would
not happen and if proper flex fan was used the blades would flatten
out from water pressure (like with high air press at higher RPMs) and
not pull the water or bend toward radiator as blades would "give".
-----------------
TheSnoMan.com
#363
Guest
Posts: n/a
Re: Re: Followup-- 2000 JGC V-8 still overheating
On Thu, 18 Jan 2007 21:03:37 -0500, Mike Romain <romainm@sympatico.ca>
wrote:
>No no, the blades of the fan act like a propeller and try to pull water.
> The flex fan blades are not strong enough to do this so they get
>pulled forward instead of the water going backward because they are so
>flexible. This can make them tag the rad fins.
>
>Water is 'heavy'. Grab a flex fan blade and see how far you can hand
>bend it in a forward direction, then talk clearance....
I understand that but again if there was a lot of clearance it would
not happen and if proper flex fan was used the blades would flatten
out from water pressure (like with high air press at higher RPMs) and
not pull the water or bend toward radiator as blades would "give".
-----------------
TheSnoMan.com
wrote:
>No no, the blades of the fan act like a propeller and try to pull water.
> The flex fan blades are not strong enough to do this so they get
>pulled forward instead of the water going backward because they are so
>flexible. This can make them tag the rad fins.
>
>Water is 'heavy'. Grab a flex fan blade and see how far you can hand
>bend it in a forward direction, then talk clearance....
I understand that but again if there was a lot of clearance it would
not happen and if proper flex fan was used the blades would flatten
out from water pressure (like with high air press at higher RPMs) and
not pull the water or bend toward radiator as blades would "give".
-----------------
TheSnoMan.com
#364
Guest
Posts: n/a
Re: Re: Followup-- 2000 JGC V-8 still overheating
On Thu, 18 Jan 2007 21:03:37 -0500, Mike Romain <romainm@sympatico.ca>
wrote:
>No no, the blades of the fan act like a propeller and try to pull water.
> The flex fan blades are not strong enough to do this so they get
>pulled forward instead of the water going backward because they are so
>flexible. This can make them tag the rad fins.
>
>Water is 'heavy'. Grab a flex fan blade and see how far you can hand
>bend it in a forward direction, then talk clearance....
I understand that but again if there was a lot of clearance it would
not happen and if proper flex fan was used the blades would flatten
out from water pressure (like with high air press at higher RPMs) and
not pull the water or bend toward radiator as blades would "give".
-----------------
TheSnoMan.com
wrote:
>No no, the blades of the fan act like a propeller and try to pull water.
> The flex fan blades are not strong enough to do this so they get
>pulled forward instead of the water going backward because they are so
>flexible. This can make them tag the rad fins.
>
>Water is 'heavy'. Grab a flex fan blade and see how far you can hand
>bend it in a forward direction, then talk clearance....
I understand that but again if there was a lot of clearance it would
not happen and if proper flex fan was used the blades would flatten
out from water pressure (like with high air press at higher RPMs) and
not pull the water or bend toward radiator as blades would "give".
-----------------
TheSnoMan.com
#365
Guest
Posts: n/a
Re: Re: Followup-- 2000 JGC V-8 still overheating
On Thu, 18 Jan 2007 21:03:37 -0500, Mike Romain <romainm@sympatico.ca>
wrote:
>No no, the blades of the fan act like a propeller and try to pull water.
> The flex fan blades are not strong enough to do this so they get
>pulled forward instead of the water going backward because they are so
>flexible. This can make them tag the rad fins.
>
>Water is 'heavy'. Grab a flex fan blade and see how far you can hand
>bend it in a forward direction, then talk clearance....
I understand that but again if there was a lot of clearance it would
not happen and if proper flex fan was used the blades would flatten
out from water pressure (like with high air press at higher RPMs) and
not pull the water or bend toward radiator as blades would "give".
-----------------
TheSnoMan.com
wrote:
>No no, the blades of the fan act like a propeller and try to pull water.
> The flex fan blades are not strong enough to do this so they get
>pulled forward instead of the water going backward because they are so
>flexible. This can make them tag the rad fins.
>
>Water is 'heavy'. Grab a flex fan blade and see how far you can hand
>bend it in a forward direction, then talk clearance....
I understand that but again if there was a lot of clearance it would
not happen and if proper flex fan was used the blades would flatten
out from water pressure (like with high air press at higher RPMs) and
not pull the water or bend toward radiator as blades would "give".
-----------------
TheSnoMan.com
#366
Guest
Posts: n/a
Re: Followup-- 2000 JGC V-8 still overheating
SnoMan wrote:
> On Thu, 18 Jan 2007 21:03:37 -0500, Mike Romain <romainm@sympatico.ca>
> wrote:
>
>> No no, the blades of the fan act like a propeller and try to pull water.
>> The flex fan blades are not strong enough to do this so they get
>> pulled forward instead of the water going backward because they are so
>> flexible. This can make them tag the rad fins.
>>
>> Water is 'heavy'. Grab a flex fan blade and see how far you can hand
>> bend it in a forward direction, then talk clearance....
>
>
> I understand that but again if there was a lot of clearance it would
> not happen and if proper flex fan was used the blades would flatten
> out from water pressure (like with high air press at higher RPMs) and
> not pull the water or bend toward radiator as blades would "give".
> -----------------
> TheSnoMan.com
Unfortunately real life doesn't work like that. Even feathered out, the
flex fan still pulls.
I have heard of folks actually stopping before a water crossing and
tying their fan off so it doesn't rotate to prevent this.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
> On Thu, 18 Jan 2007 21:03:37 -0500, Mike Romain <romainm@sympatico.ca>
> wrote:
>
>> No no, the blades of the fan act like a propeller and try to pull water.
>> The flex fan blades are not strong enough to do this so they get
>> pulled forward instead of the water going backward because they are so
>> flexible. This can make them tag the rad fins.
>>
>> Water is 'heavy'. Grab a flex fan blade and see how far you can hand
>> bend it in a forward direction, then talk clearance....
>
>
> I understand that but again if there was a lot of clearance it would
> not happen and if proper flex fan was used the blades would flatten
> out from water pressure (like with high air press at higher RPMs) and
> not pull the water or bend toward radiator as blades would "give".
> -----------------
> TheSnoMan.com
Unfortunately real life doesn't work like that. Even feathered out, the
flex fan still pulls.
I have heard of folks actually stopping before a water crossing and
tying their fan off so it doesn't rotate to prevent this.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
#367
Guest
Posts: n/a
Re: Followup-- 2000 JGC V-8 still overheating
SnoMan wrote:
> On Thu, 18 Jan 2007 21:03:37 -0500, Mike Romain <romainm@sympatico.ca>
> wrote:
>
>> No no, the blades of the fan act like a propeller and try to pull water.
>> The flex fan blades are not strong enough to do this so they get
>> pulled forward instead of the water going backward because they are so
>> flexible. This can make them tag the rad fins.
>>
>> Water is 'heavy'. Grab a flex fan blade and see how far you can hand
>> bend it in a forward direction, then talk clearance....
>
>
> I understand that but again if there was a lot of clearance it would
> not happen and if proper flex fan was used the blades would flatten
> out from water pressure (like with high air press at higher RPMs) and
> not pull the water or bend toward radiator as blades would "give".
> -----------------
> TheSnoMan.com
Unfortunately real life doesn't work like that. Even feathered out, the
flex fan still pulls.
I have heard of folks actually stopping before a water crossing and
tying their fan off so it doesn't rotate to prevent this.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
> On Thu, 18 Jan 2007 21:03:37 -0500, Mike Romain <romainm@sympatico.ca>
> wrote:
>
>> No no, the blades of the fan act like a propeller and try to pull water.
>> The flex fan blades are not strong enough to do this so they get
>> pulled forward instead of the water going backward because they are so
>> flexible. This can make them tag the rad fins.
>>
>> Water is 'heavy'. Grab a flex fan blade and see how far you can hand
>> bend it in a forward direction, then talk clearance....
>
>
> I understand that but again if there was a lot of clearance it would
> not happen and if proper flex fan was used the blades would flatten
> out from water pressure (like with high air press at higher RPMs) and
> not pull the water or bend toward radiator as blades would "give".
> -----------------
> TheSnoMan.com
Unfortunately real life doesn't work like that. Even feathered out, the
flex fan still pulls.
I have heard of folks actually stopping before a water crossing and
tying their fan off so it doesn't rotate to prevent this.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
#368
Guest
Posts: n/a
Re: Followup-- 2000 JGC V-8 still overheating
SnoMan wrote:
> On Thu, 18 Jan 2007 21:03:37 -0500, Mike Romain <romainm@sympatico.ca>
> wrote:
>
>> No no, the blades of the fan act like a propeller and try to pull water.
>> The flex fan blades are not strong enough to do this so they get
>> pulled forward instead of the water going backward because they are so
>> flexible. This can make them tag the rad fins.
>>
>> Water is 'heavy'. Grab a flex fan blade and see how far you can hand
>> bend it in a forward direction, then talk clearance....
>
>
> I understand that but again if there was a lot of clearance it would
> not happen and if proper flex fan was used the blades would flatten
> out from water pressure (like with high air press at higher RPMs) and
> not pull the water or bend toward radiator as blades would "give".
> -----------------
> TheSnoMan.com
Unfortunately real life doesn't work like that. Even feathered out, the
flex fan still pulls.
I have heard of folks actually stopping before a water crossing and
tying their fan off so it doesn't rotate to prevent this.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
> On Thu, 18 Jan 2007 21:03:37 -0500, Mike Romain <romainm@sympatico.ca>
> wrote:
>
>> No no, the blades of the fan act like a propeller and try to pull water.
>> The flex fan blades are not strong enough to do this so they get
>> pulled forward instead of the water going backward because they are so
>> flexible. This can make them tag the rad fins.
>>
>> Water is 'heavy'. Grab a flex fan blade and see how far you can hand
>> bend it in a forward direction, then talk clearance....
>
>
> I understand that but again if there was a lot of clearance it would
> not happen and if proper flex fan was used the blades would flatten
> out from water pressure (like with high air press at higher RPMs) and
> not pull the water or bend toward radiator as blades would "give".
> -----------------
> TheSnoMan.com
Unfortunately real life doesn't work like that. Even feathered out, the
flex fan still pulls.
I have heard of folks actually stopping before a water crossing and
tying their fan off so it doesn't rotate to prevent this.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
#369
Guest
Posts: n/a
Re: Followup-- 2000 JGC V-8 still overheating
SnoMan wrote:
> On Thu, 18 Jan 2007 21:03:37 -0500, Mike Romain <romainm@sympatico.ca>
> wrote:
>
>> No no, the blades of the fan act like a propeller and try to pull water.
>> The flex fan blades are not strong enough to do this so they get
>> pulled forward instead of the water going backward because they are so
>> flexible. This can make them tag the rad fins.
>>
>> Water is 'heavy'. Grab a flex fan blade and see how far you can hand
>> bend it in a forward direction, then talk clearance....
>
>
> I understand that but again if there was a lot of clearance it would
> not happen and if proper flex fan was used the blades would flatten
> out from water pressure (like with high air press at higher RPMs) and
> not pull the water or bend toward radiator as blades would "give".
> -----------------
> TheSnoMan.com
Unfortunately real life doesn't work like that. Even feathered out, the
flex fan still pulls.
I have heard of folks actually stopping before a water crossing and
tying their fan off so it doesn't rotate to prevent this.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
> On Thu, 18 Jan 2007 21:03:37 -0500, Mike Romain <romainm@sympatico.ca>
> wrote:
>
>> No no, the blades of the fan act like a propeller and try to pull water.
>> The flex fan blades are not strong enough to do this so they get
>> pulled forward instead of the water going backward because they are so
>> flexible. This can make them tag the rad fins.
>>
>> Water is 'heavy'. Grab a flex fan blade and see how far you can hand
>> bend it in a forward direction, then talk clearance....
>
>
> I understand that but again if there was a lot of clearance it would
> not happen and if proper flex fan was used the blades would flatten
> out from water pressure (like with high air press at higher RPMs) and
> not pull the water or bend toward radiator as blades would "give".
> -----------------
> TheSnoMan.com
Unfortunately real life doesn't work like that. Even feathered out, the
flex fan still pulls.
I have heard of folks actually stopping before a water crossing and
tying their fan off so it doesn't rotate to prevent this.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
#370
Guest
Posts: n/a
Re: Re: Followup-- 2000 JGC V-8 still overheating
On Fri, 19 Jan 2007 09:52:20 -0500, Mike Romain <romainm@sympatico.ca>
wrote:
>Unfortunately real life doesn't work like that. Even feathered out, the
>flex fan still pulls.
>
>I have heard of folks actually stopping before a water crossing and
>tying their fan off so it doesn't rotate to prevent this.
The proper flex fan with proper clearance would prevent this. I have
forded water up to 4 foot deep in years past many times with no
problems at all but them it was also with vehicles that had a lot of
clearance between fan and radiator. Also if you where concerned about
it, you could simpley remove or loose fan belt and then replace it or
retighten the belt afterwards. This would also save you from sucking
water into altenator YOu might have manual steering for a bit
depending on belt setup but it is not a big deal for a short period of
time.
-----------------
TheSnoMan.com
wrote:
>Unfortunately real life doesn't work like that. Even feathered out, the
>flex fan still pulls.
>
>I have heard of folks actually stopping before a water crossing and
>tying their fan off so it doesn't rotate to prevent this.
The proper flex fan with proper clearance would prevent this. I have
forded water up to 4 foot deep in years past many times with no
problems at all but them it was also with vehicles that had a lot of
clearance between fan and radiator. Also if you where concerned about
it, you could simpley remove or loose fan belt and then replace it or
retighten the belt afterwards. This would also save you from sucking
water into altenator YOu might have manual steering for a bit
depending on belt setup but it is not a big deal for a short period of
time.
-----------------
TheSnoMan.com