Thom

Thanks guys.

The Holley Rebuild Kit show in Bill's picture is already applied, and
IIRC I have a power valve saver already installed, but I will check.
I just moved, so fixing the Jeep is lower on my priority list. Getting
a good internet connection up and running again is more important,
posting by Google doesn't do it for me ;-)

Thom.


"c" <c@me.org> wrote in message news:<p5%mb.78655$pg7.14168@twister.rdc-kc.rr.com>...
> Yup, those are the new non stick gaskets I was mentioning.
>
> Here is the power valve saver kit that they now sell:
> http://tinyurl.com/sgy5
>
> Holley has a kit as well.
> http://www.holley.com/HiOctn/ProdLin...A/125-500.html
>
> Like I said earlier, you can do this yourself with a little ball bearing
> (1/4" IIRC), a drill bit 1/32" bigger than the ball, and a Phillips
> screwdriver and hammer.
>
> If you follow the vacuum port signal from the well behind the power valve in
> the main body, it will eventually come out the bottom of the main body and
> pass through the throttle base plate.. Drill the hole in the baseplate deep
> enough to let the ball sit below the gasket surface of the baseplate. It
> only needs to be about 1/16" below the surface. Then take a Phillips
> screwdriver that fits in the hole and give it a good tap with a hammer to
> make 4 grooves in the face left by the point of the drill. This will allow
> the vacuum signal to operate the power valve properly. If the carb
> backfires, the ball will seat up against the main body of the carb and
> prevent the pressure from getting to the diaphragm. I have a carb here that
> needs to have this done, so in the near future I will try to put together a
> website showing the procedure. It id real easy to do. Even the kit is a deal
> at about $10 because a replacement power valve is usually $6-8 in the
> stores, and then you have the hassles of changing the damn thing.
>
> Chris
>
>
>
>

Thom

Thanks guys.

The Holley Rebuild Kit show in Bill's picture is already applied, and
IIRC I have a power valve saver already installed, but I will check.
I just moved, so fixing the Jeep is lower on my priority list. Getting
a good internet connection up and running again is more important,
posting by Google doesn't do it for me ;-)

Thom.


"c" <c@me.org> wrote in message news:<p5%mb.78655$pg7.14168@twister.rdc-kc.rr.com>...
> Yup, those are the new non stick gaskets I was mentioning.
>
> Here is the power valve saver kit that they now sell:
> http://tinyurl.com/sgy5
>
> Holley has a kit as well.
> http://www.holley.com/HiOctn/ProdLin...A/125-500.html
>
> Like I said earlier, you can do this yourself with a little ball bearing
> (1/4" IIRC), a drill bit 1/32" bigger than the ball, and a Phillips
> screwdriver and hammer.
>
> If you follow the vacuum port signal from the well behind the power valve in
> the main body, it will eventually come out the bottom of the main body and
> pass through the throttle base plate.. Drill the hole in the baseplate deep
> enough to let the ball sit below the gasket surface of the baseplate. It
> only needs to be about 1/16" below the surface. Then take a Phillips
> screwdriver that fits in the hole and give it a good tap with a hammer to
> make 4 grooves in the face left by the point of the drill. This will allow
> the vacuum signal to operate the power valve properly. If the carb
> backfires, the ball will seat up against the main body of the carb and
> prevent the pressure from getting to the diaphragm. I have a carb here that
> needs to have this done, so in the near future I will try to put together a
> website showing the procedure. It id real easy to do. Even the kit is a deal
> at about $10 because a replacement power valve is usually $6-8 in the
> stores, and then you have the hassles of changing the damn thing.
>
> Chris
>
>
>
>

Thom

Thanks guys.

The Holley Rebuild Kit show in Bill's picture is already applied, and
IIRC I have a power valve saver already installed, but I will check.
I just moved, so fixing the Jeep is lower on my priority list. Getting
a good internet connection up and running again is more important,
posting by Google doesn't do it for me ;-)

Thom.


"c" <c@me.org> wrote in message news:<p5%mb.78655$pg7.14168@twister.rdc-kc.rr.com>...
> Yup, those are the new non stick gaskets I was mentioning.
>
> Here is the power valve saver kit that they now sell:
> http://tinyurl.com/sgy5
>
> Holley has a kit as well.
> http://www.holley.com/HiOctn/ProdLin...A/125-500.html
>
> Like I said earlier, you can do this yourself with a little ball bearing
> (1/4" IIRC), a drill bit 1/32" bigger than the ball, and a Phillips
> screwdriver and hammer.
>
> If you follow the vacuum port signal from the well behind the power valve in
> the main body, it will eventually come out the bottom of the main body and
> pass through the throttle base plate.. Drill the hole in the baseplate deep
> enough to let the ball sit below the gasket surface of the baseplate. It
> only needs to be about 1/16" below the surface. Then take a Phillips
> screwdriver that fits in the hole and give it a good tap with a hammer to
> make 4 grooves in the face left by the point of the drill. This will allow
> the vacuum signal to operate the power valve properly. If the carb
> backfires, the ball will seat up against the main body of the carb and
> prevent the pressure from getting to the diaphragm. I have a carb here that
> needs to have this done, so in the near future I will try to put together a
> website showing the procedure. It id real easy to do. Even the kit is a deal
> at about $10 because a replacement power valve is usually $6-8 in the
> stores, and then you have the hassles of changing the damn thing.
>
> Chris
>
>
>
>