dana 300 twin stick - question
Guest
Posts: n/a
Re: dana 300 twin stick - question
Dont think of it as 2wd/4wd any more - just remember:
Left stick = rear axle
Right stick = front axle
and for each stick:
Stick forward = lo
Stick center = neutral
Stick aft = high
Therefore,
2hi rear = left aft, right center
2hi front = left center, right aft
2lo rear = left forward, right center
2lo front = left center, right forward
4hi = left aft, right aft
4lo = left forward, right forward
I just did my twin stick two weekends ago. I didn't want to mess with
any 'pills' so I was willing to not have the full twin stick
capabilities. Imagine my surprise when I finished and discovered I
could get all 6 combinations mentioned above! But, my case has 192k
miles on it, the pills could be shot. But, something still (thankfully)
prevents getting one axle in high and one in low at the same time.
My kit also came with a decal. If you need to see it, there is a
similar one at http://www.bearcreeksurvey.com/NOSRepro.htm, patterns 010
and 013 show the proper 300 twin stick pattern.
Left stick = rear axle
Right stick = front axle
and for each stick:
Stick forward = lo
Stick center = neutral
Stick aft = high
Therefore,
2hi rear = left aft, right center
2hi front = left center, right aft
2lo rear = left forward, right center
2lo front = left center, right forward
4hi = left aft, right aft
4lo = left forward, right forward
I just did my twin stick two weekends ago. I didn't want to mess with
any 'pills' so I was willing to not have the full twin stick
capabilities. Imagine my surprise when I finished and discovered I
could get all 6 combinations mentioned above! But, my case has 192k
miles on it, the pills could be shot. But, something still (thankfully)
prevents getting one axle in high and one in low at the same time.
My kit also came with a decal. If you need to see it, there is a
similar one at http://www.bearcreeksurvey.com/NOSRepro.htm, patterns 010
and 013 show the proper 300 twin stick pattern.
Guest
Posts: n/a
Re: dana 300 twin stick - question
Dont think of it as 2wd/4wd any more - just remember:
Left stick = rear axle
Right stick = front axle
and for each stick:
Stick forward = lo
Stick center = neutral
Stick aft = high
Therefore,
2hi rear = left aft, right center
2hi front = left center, right aft
2lo rear = left forward, right center
2lo front = left center, right forward
4hi = left aft, right aft
4lo = left forward, right forward
I just did my twin stick two weekends ago. I didn't want to mess with
any 'pills' so I was willing to not have the full twin stick
capabilities. Imagine my surprise when I finished and discovered I
could get all 6 combinations mentioned above! But, my case has 192k
miles on it, the pills could be shot. But, something still (thankfully)
prevents getting one axle in high and one in low at the same time.
My kit also came with a decal. If you need to see it, there is a
similar one at http://www.bearcreeksurvey.com/NOSRepro.htm, patterns 010
and 013 show the proper 300 twin stick pattern.
Left stick = rear axle
Right stick = front axle
and for each stick:
Stick forward = lo
Stick center = neutral
Stick aft = high
Therefore,
2hi rear = left aft, right center
2hi front = left center, right aft
2lo rear = left forward, right center
2lo front = left center, right forward
4hi = left aft, right aft
4lo = left forward, right forward
I just did my twin stick two weekends ago. I didn't want to mess with
any 'pills' so I was willing to not have the full twin stick
capabilities. Imagine my surprise when I finished and discovered I
could get all 6 combinations mentioned above! But, my case has 192k
miles on it, the pills could be shot. But, something still (thankfully)
prevents getting one axle in high and one in low at the same time.
My kit also came with a decal. If you need to see it, there is a
similar one at http://www.bearcreeksurvey.com/NOSRepro.htm, patterns 010
and 013 show the proper 300 twin stick pattern.
Guest
Posts: n/a
Re: dana 300 twin stick - question
Mine won't do 2HI, FWD.
Left stick is HI and LO, Right stick is 2 and 4.
"Clap Trap" <nowhere@the.net> wrote in message
news:b1cf4$42421fdd$18d60a3d$22368@KNOLOGY.NET...
> Dont think of it as 2wd/4wd any more - just remember:
>
> Left stick = rear axle
> Right stick = front axle
>
> and for each stick:
>
> Stick forward = lo
> Stick center = neutral
> Stick aft = high
>
> Therefore,
>
> 2hi rear = left aft, right center
> 2hi front = left center, right aft
> 2lo rear = left forward, right center
> 2lo front = left center, right forward
> 4hi = left aft, right aft
> 4lo = left forward, right forward
>
> I just did my twin stick two weekends ago. I didn't want to mess with any
> 'pills' so I was willing to not have the full twin stick capabilities.
> Imagine my surprise when I finished and discovered I could get all 6
> combinations mentioned above! But, my case has 192k miles on it, the
> pills could be shot. But, something still (thankfully) prevents getting
> one axle in high and one in low at the same time.
>
> My kit also came with a decal. If you need to see it, there is a similar
> one at http://www.bearcreeksurvey.com/NOSRepro.htm, patterns 010 and 013
> show the proper 300 twin stick pattern.
Left stick is HI and LO, Right stick is 2 and 4.
"Clap Trap" <nowhere@the.net> wrote in message
news:b1cf4$42421fdd$18d60a3d$22368@KNOLOGY.NET...
> Dont think of it as 2wd/4wd any more - just remember:
>
> Left stick = rear axle
> Right stick = front axle
>
> and for each stick:
>
> Stick forward = lo
> Stick center = neutral
> Stick aft = high
>
> Therefore,
>
> 2hi rear = left aft, right center
> 2hi front = left center, right aft
> 2lo rear = left forward, right center
> 2lo front = left center, right forward
> 4hi = left aft, right aft
> 4lo = left forward, right forward
>
> I just did my twin stick two weekends ago. I didn't want to mess with any
> 'pills' so I was willing to not have the full twin stick capabilities.
> Imagine my surprise when I finished and discovered I could get all 6
> combinations mentioned above! But, my case has 192k miles on it, the
> pills could be shot. But, something still (thankfully) prevents getting
> one axle in high and one in low at the same time.
>
> My kit also came with a decal. If you need to see it, there is a similar
> one at http://www.bearcreeksurvey.com/NOSRepro.htm, patterns 010 and 013
> show the proper 300 twin stick pattern.
Guest
Posts: n/a
Re: dana 300 twin stick - question
Mine won't do 2HI, FWD.
Left stick is HI and LO, Right stick is 2 and 4.
"Clap Trap" <nowhere@the.net> wrote in message
news:b1cf4$42421fdd$18d60a3d$22368@KNOLOGY.NET...
> Dont think of it as 2wd/4wd any more - just remember:
>
> Left stick = rear axle
> Right stick = front axle
>
> and for each stick:
>
> Stick forward = lo
> Stick center = neutral
> Stick aft = high
>
> Therefore,
>
> 2hi rear = left aft, right center
> 2hi front = left center, right aft
> 2lo rear = left forward, right center
> 2lo front = left center, right forward
> 4hi = left aft, right aft
> 4lo = left forward, right forward
>
> I just did my twin stick two weekends ago. I didn't want to mess with any
> 'pills' so I was willing to not have the full twin stick capabilities.
> Imagine my surprise when I finished and discovered I could get all 6
> combinations mentioned above! But, my case has 192k miles on it, the
> pills could be shot. But, something still (thankfully) prevents getting
> one axle in high and one in low at the same time.
>
> My kit also came with a decal. If you need to see it, there is a similar
> one at http://www.bearcreeksurvey.com/NOSRepro.htm, patterns 010 and 013
> show the proper 300 twin stick pattern.
Left stick is HI and LO, Right stick is 2 and 4.
"Clap Trap" <nowhere@the.net> wrote in message
news:b1cf4$42421fdd$18d60a3d$22368@KNOLOGY.NET...
> Dont think of it as 2wd/4wd any more - just remember:
>
> Left stick = rear axle
> Right stick = front axle
>
> and for each stick:
>
> Stick forward = lo
> Stick center = neutral
> Stick aft = high
>
> Therefore,
>
> 2hi rear = left aft, right center
> 2hi front = left center, right aft
> 2lo rear = left forward, right center
> 2lo front = left center, right forward
> 4hi = left aft, right aft
> 4lo = left forward, right forward
>
> I just did my twin stick two weekends ago. I didn't want to mess with any
> 'pills' so I was willing to not have the full twin stick capabilities.
> Imagine my surprise when I finished and discovered I could get all 6
> combinations mentioned above! But, my case has 192k miles on it, the
> pills could be shot. But, something still (thankfully) prevents getting
> one axle in high and one in low at the same time.
>
> My kit also came with a decal. If you need to see it, there is a similar
> one at http://www.bearcreeksurvey.com/NOSRepro.htm, patterns 010 and 013
> show the proper 300 twin stick pattern.
Guest
Posts: n/a
Re: dana 300 twin stick - question
Mine won't do 2HI, FWD.
Left stick is HI and LO, Right stick is 2 and 4.
"Clap Trap" <nowhere@the.net> wrote in message
news:b1cf4$42421fdd$18d60a3d$22368@KNOLOGY.NET...
> Dont think of it as 2wd/4wd any more - just remember:
>
> Left stick = rear axle
> Right stick = front axle
>
> and for each stick:
>
> Stick forward = lo
> Stick center = neutral
> Stick aft = high
>
> Therefore,
>
> 2hi rear = left aft, right center
> 2hi front = left center, right aft
> 2lo rear = left forward, right center
> 2lo front = left center, right forward
> 4hi = left aft, right aft
> 4lo = left forward, right forward
>
> I just did my twin stick two weekends ago. I didn't want to mess with any
> 'pills' so I was willing to not have the full twin stick capabilities.
> Imagine my surprise when I finished and discovered I could get all 6
> combinations mentioned above! But, my case has 192k miles on it, the
> pills could be shot. But, something still (thankfully) prevents getting
> one axle in high and one in low at the same time.
>
> My kit also came with a decal. If you need to see it, there is a similar
> one at http://www.bearcreeksurvey.com/NOSRepro.htm, patterns 010 and 013
> show the proper 300 twin stick pattern.
Left stick is HI and LO, Right stick is 2 and 4.
"Clap Trap" <nowhere@the.net> wrote in message
news:b1cf4$42421fdd$18d60a3d$22368@KNOLOGY.NET...
> Dont think of it as 2wd/4wd any more - just remember:
>
> Left stick = rear axle
> Right stick = front axle
>
> and for each stick:
>
> Stick forward = lo
> Stick center = neutral
> Stick aft = high
>
> Therefore,
>
> 2hi rear = left aft, right center
> 2hi front = left center, right aft
> 2lo rear = left forward, right center
> 2lo front = left center, right forward
> 4hi = left aft, right aft
> 4lo = left forward, right forward
>
> I just did my twin stick two weekends ago. I didn't want to mess with any
> 'pills' so I was willing to not have the full twin stick capabilities.
> Imagine my surprise when I finished and discovered I could get all 6
> combinations mentioned above! But, my case has 192k miles on it, the
> pills could be shot. But, something still (thankfully) prevents getting
> one axle in high and one in low at the same time.
>
> My kit also came with a decal. If you need to see it, there is a similar
> one at http://www.bearcreeksurvey.com/NOSRepro.htm, patterns 010 and 013
> show the proper 300 twin stick pattern.
Guest
Posts: n/a
Re: dana 300 twin stick - question
That's not a D300 tcase.
"L.W. ("ßill") ------ III" <----------@***.net> wrote in message
news:4240E0F0.B54D786F@***.net...
> A twin stick should shift the same as a twin stick:
> http://www.----------.com/DashPlate.gif
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> HomeBrewer wrote:
>>
>> After I get the starting problem fixed....see my other thread... I will
>> be
>> going wheelin. I just replaced my tranny and added a twin stick to the
>> dana
>> 300. I also removed the "pills" from the shift levers and now I can
>> switch
>> low range into each axle seperately. My question is what is the shift
>> pattern with my new setup? I found this page:
>> http://www.sierrajeep.com/shift.htm but I thought I had 4 shift points on
>> each stick. the single stick had 4H, 4L, N, 2H. What am I missing?
>> --
>> ___________________
>> HomeBrewer
>> http://85cj7.blogspot.com/
>> http://85cj7.webhop.net/
>> http://funfacts.webhop.org/
>> "When you decide something is impossible to do, try to stay out of the
>> way
>> of the man that's doing it."
"L.W. ("ßill") ------ III" <----------@***.net> wrote in message
news:4240E0F0.B54D786F@***.net...
> A twin stick should shift the same as a twin stick:
> http://www.----------.com/DashPlate.gif
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> HomeBrewer wrote:
>>
>> After I get the starting problem fixed....see my other thread... I will
>> be
>> going wheelin. I just replaced my tranny and added a twin stick to the
>> dana
>> 300. I also removed the "pills" from the shift levers and now I can
>> switch
>> low range into each axle seperately. My question is what is the shift
>> pattern with my new setup? I found this page:
>> http://www.sierrajeep.com/shift.htm but I thought I had 4 shift points on
>> each stick. the single stick had 4H, 4L, N, 2H. What am I missing?
>> --
>> ___________________
>> HomeBrewer
>> http://85cj7.blogspot.com/
>> http://85cj7.webhop.net/
>> http://funfacts.webhop.org/
>> "When you decide something is impossible to do, try to stay out of the
>> way
>> of the man that's doing it."
Guest
Posts: n/a
Re: dana 300 twin stick - question
That's not a D300 tcase.
"L.W. ("ßill") ------ III" <----------@***.net> wrote in message
news:4240E0F0.B54D786F@***.net...
> A twin stick should shift the same as a twin stick:
> http://www.----------.com/DashPlate.gif
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> HomeBrewer wrote:
>>
>> After I get the starting problem fixed....see my other thread... I will
>> be
>> going wheelin. I just replaced my tranny and added a twin stick to the
>> dana
>> 300. I also removed the "pills" from the shift levers and now I can
>> switch
>> low range into each axle seperately. My question is what is the shift
>> pattern with my new setup? I found this page:
>> http://www.sierrajeep.com/shift.htm but I thought I had 4 shift points on
>> each stick. the single stick had 4H, 4L, N, 2H. What am I missing?
>> --
>> ___________________
>> HomeBrewer
>> http://85cj7.blogspot.com/
>> http://85cj7.webhop.net/
>> http://funfacts.webhop.org/
>> "When you decide something is impossible to do, try to stay out of the
>> way
>> of the man that's doing it."
"L.W. ("ßill") ------ III" <----------@***.net> wrote in message
news:4240E0F0.B54D786F@***.net...
> A twin stick should shift the same as a twin stick:
> http://www.----------.com/DashPlate.gif
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> HomeBrewer wrote:
>>
>> After I get the starting problem fixed....see my other thread... I will
>> be
>> going wheelin. I just replaced my tranny and added a twin stick to the
>> dana
>> 300. I also removed the "pills" from the shift levers and now I can
>> switch
>> low range into each axle seperately. My question is what is the shift
>> pattern with my new setup? I found this page:
>> http://www.sierrajeep.com/shift.htm but I thought I had 4 shift points on
>> each stick. the single stick had 4H, 4L, N, 2H. What am I missing?
>> --
>> ___________________
>> HomeBrewer
>> http://85cj7.blogspot.com/
>> http://85cj7.webhop.net/
>> http://funfacts.webhop.org/
>> "When you decide something is impossible to do, try to stay out of the
>> way
>> of the man that's doing it."
Guest
Posts: n/a
Re: dana 300 twin stick - question
That's not a D300 tcase.
"L.W. ("ßill") ------ III" <----------@***.net> wrote in message
news:4240E0F0.B54D786F@***.net...
> A twin stick should shift the same as a twin stick:
> http://www.----------.com/DashPlate.gif
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> HomeBrewer wrote:
>>
>> After I get the starting problem fixed....see my other thread... I will
>> be
>> going wheelin. I just replaced my tranny and added a twin stick to the
>> dana
>> 300. I also removed the "pills" from the shift levers and now I can
>> switch
>> low range into each axle seperately. My question is what is the shift
>> pattern with my new setup? I found this page:
>> http://www.sierrajeep.com/shift.htm but I thought I had 4 shift points on
>> each stick. the single stick had 4H, 4L, N, 2H. What am I missing?
>> --
>> ___________________
>> HomeBrewer
>> http://85cj7.blogspot.com/
>> http://85cj7.webhop.net/
>> http://funfacts.webhop.org/
>> "When you decide something is impossible to do, try to stay out of the
>> way
>> of the man that's doing it."
"L.W. ("ßill") ------ III" <----------@***.net> wrote in message
news:4240E0F0.B54D786F@***.net...
> A twin stick should shift the same as a twin stick:
> http://www.----------.com/DashPlate.gif
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> HomeBrewer wrote:
>>
>> After I get the starting problem fixed....see my other thread... I will
>> be
>> going wheelin. I just replaced my tranny and added a twin stick to the
>> dana
>> 300. I also removed the "pills" from the shift levers and now I can
>> switch
>> low range into each axle seperately. My question is what is the shift
>> pattern with my new setup? I found this page:
>> http://www.sierrajeep.com/shift.htm but I thought I had 4 shift points on
>> each stick. the single stick had 4H, 4L, N, 2H. What am I missing?
>> --
>> ___________________
>> HomeBrewer
>> http://85cj7.blogspot.com/
>> http://85cj7.webhop.net/
>> http://funfacts.webhop.org/
>> "When you decide something is impossible to do, try to stay out of the
>> way
>> of the man that's doing it."
Guest
Posts: n/a
Re: dana 300 twin stick - question
I have the Currie TwinStick, and I haven't got the 2HI, FWD option. I don't
know why. I have never had this option.
"Serg" <none@none.com> wrote in message
news:3aea72F68l3t0U1@individual.net...
> so one site says front 2wd high is possible and the other says is not. is
> that because todd (sierrajeep) is using the currie kit? and 7slotgrille is
> using a home-made version?
>
> "HomeBrewer" <85cj7XXX@***.net> wrote in message
> news:3ac3i7F69tst1U1@individual.net...
>> After I get the starting problem fixed....see my other thread... I will
>> be
>> going wheelin. I just replaced my tranny and added a twin stick to the
> dana
>> 300. I also removed the "pills" from the shift levers and now I can
>> switch
>> low range into each axle seperately. My question is what is the shift
>> pattern with my new setup? I found this page:
>> http://www.sierrajeep.com/shift.htm but I thought I had 4 shift points on
>> each stick. the single stick had 4H, 4L, N, 2H. What am I missing?
>> --
>> ___________________
>> HomeBrewer
>> http://85cj7.blogspot.com/
>> http://85cj7.webhop.net/
>> http://funfacts.webhop.org/
>> "When you decide something is impossible to do, try to stay out of the
>> way
>> of the man that's doing it."
>>
>>
>
>
know why. I have never had this option.
"Serg" <none@none.com> wrote in message
news:3aea72F68l3t0U1@individual.net...
> so one site says front 2wd high is possible and the other says is not. is
> that because todd (sierrajeep) is using the currie kit? and 7slotgrille is
> using a home-made version?
>
> "HomeBrewer" <85cj7XXX@***.net> wrote in message
> news:3ac3i7F69tst1U1@individual.net...
>> After I get the starting problem fixed....see my other thread... I will
>> be
>> going wheelin. I just replaced my tranny and added a twin stick to the
> dana
>> 300. I also removed the "pills" from the shift levers and now I can
>> switch
>> low range into each axle seperately. My question is what is the shift
>> pattern with my new setup? I found this page:
>> http://www.sierrajeep.com/shift.htm but I thought I had 4 shift points on
>> each stick. the single stick had 4H, 4L, N, 2H. What am I missing?
>> --
>> ___________________
>> HomeBrewer
>> http://85cj7.blogspot.com/
>> http://85cj7.webhop.net/
>> http://funfacts.webhop.org/
>> "When you decide something is impossible to do, try to stay out of the
>> way
>> of the man that's doing it."
>>
>>
>
>
Guest
Posts: n/a
Re: dana 300 twin stick - question
I have the Currie TwinStick, and I haven't got the 2HI, FWD option. I don't
know why. I have never had this option.
"Serg" <none@none.com> wrote in message
news:3aea72F68l3t0U1@individual.net...
> so one site says front 2wd high is possible and the other says is not. is
> that because todd (sierrajeep) is using the currie kit? and 7slotgrille is
> using a home-made version?
>
> "HomeBrewer" <85cj7XXX@***.net> wrote in message
> news:3ac3i7F69tst1U1@individual.net...
>> After I get the starting problem fixed....see my other thread... I will
>> be
>> going wheelin. I just replaced my tranny and added a twin stick to the
> dana
>> 300. I also removed the "pills" from the shift levers and now I can
>> switch
>> low range into each axle seperately. My question is what is the shift
>> pattern with my new setup? I found this page:
>> http://www.sierrajeep.com/shift.htm but I thought I had 4 shift points on
>> each stick. the single stick had 4H, 4L, N, 2H. What am I missing?
>> --
>> ___________________
>> HomeBrewer
>> http://85cj7.blogspot.com/
>> http://85cj7.webhop.net/
>> http://funfacts.webhop.org/
>> "When you decide something is impossible to do, try to stay out of the
>> way
>> of the man that's doing it."
>>
>>
>
>
know why. I have never had this option.
"Serg" <none@none.com> wrote in message
news:3aea72F68l3t0U1@individual.net...
> so one site says front 2wd high is possible and the other says is not. is
> that because todd (sierrajeep) is using the currie kit? and 7slotgrille is
> using a home-made version?
>
> "HomeBrewer" <85cj7XXX@***.net> wrote in message
> news:3ac3i7F69tst1U1@individual.net...
>> After I get the starting problem fixed....see my other thread... I will
>> be
>> going wheelin. I just replaced my tranny and added a twin stick to the
> dana
>> 300. I also removed the "pills" from the shift levers and now I can
>> switch
>> low range into each axle seperately. My question is what is the shift
>> pattern with my new setup? I found this page:
>> http://www.sierrajeep.com/shift.htm but I thought I had 4 shift points on
>> each stick. the single stick had 4H, 4L, N, 2H. What am I missing?
>> --
>> ___________________
>> HomeBrewer
>> http://85cj7.blogspot.com/
>> http://85cj7.webhop.net/
>> http://funfacts.webhop.org/
>> "When you decide something is impossible to do, try to stay out of the
>> way
>> of the man that's doing it."
>>
>>
>
>