Any Alignment specialist?
#21
Guest
Posts: n/a
Re: Any Alignment specialist?
Steve did you read the Poster's reply? Now if you'd let him reply
to my questioning on the position of the bend, and suggesting the
opposite tire wear, then we could have gone from there. Have you bent
the tube at the end before?
Is this your Daddy? http://Steve-Garner.com/
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Steve G wrote:
>
> Here's L.W. (Bill)again with his absolutely, know better than anyone,
> without a doubt, you're an idiot, armchair diagnosis. How does he do it?
>
> Let's suppose for a minute that he does actually know how to test a ball
> joint. Most people with enough knowledge to set up the alignment equipment
> and know what a camber reading is are usually smart enough to check the
> frontend for looseness before strapping on the equipment. So, whether that
> was Yellow Fever or his favourite mechanic, they're already way ahead of you
> L.W.(Bill) ------ III. Having established that much, it doesn't matter
> where the bend is along the tube, at the inboard end at the housing or the
> outer end of the tube, if it's bending up you will lose camber. A half of
> one degree is not enough that you will burn the edge of the tire off in
> short order. If you rotate the tires a little more frequently you will
> probably not notice the difference. Personally, I would strap down or
> somehow anchor the outer end of the tube and put my floor jack under the
> diff housing right at the entrance of the tube and take the bend out. If
> you're not comfortable doing it yourself. any truck alignment shop can do
> it, that's exactly how camber is adjusted on solid axles, bending the axle.
> Steve g.
to my questioning on the position of the bend, and suggesting the
opposite tire wear, then we could have gone from there. Have you bent
the tube at the end before?
Is this your Daddy? http://Steve-Garner.com/
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Steve G wrote:
>
> Here's L.W. (Bill)again with his absolutely, know better than anyone,
> without a doubt, you're an idiot, armchair diagnosis. How does he do it?
>
> Let's suppose for a minute that he does actually know how to test a ball
> joint. Most people with enough knowledge to set up the alignment equipment
> and know what a camber reading is are usually smart enough to check the
> frontend for looseness before strapping on the equipment. So, whether that
> was Yellow Fever or his favourite mechanic, they're already way ahead of you
> L.W.(Bill) ------ III. Having established that much, it doesn't matter
> where the bend is along the tube, at the inboard end at the housing or the
> outer end of the tube, if it's bending up you will lose camber. A half of
> one degree is not enough that you will burn the edge of the tire off in
> short order. If you rotate the tires a little more frequently you will
> probably not notice the difference. Personally, I would strap down or
> somehow anchor the outer end of the tube and put my floor jack under the
> diff housing right at the entrance of the tube and take the bend out. If
> you're not comfortable doing it yourself. any truck alignment shop can do
> it, that's exactly how camber is adjusted on solid axles, bending the axle.
> Steve g.
#22
Guest
Posts: n/a
Re: Any Alignment specialist?
"Yellow Fever" <roadrnnr99@REMOVE.yahoo.com> wrote in message
news:10erosjanjgvt72@corp.supernews.com...
: Nope, ball joints tight.
: the axle tube is bent up slightly at end causing top of wheel to be off
by
: said degrees.
:
:
If you are really concerned about it, you could have the axle straightened
(best fix) or you could install an offset ball joint to correct the camber
(band-aid solution):
http://www.jegs.com/cgi-bin/ncommerc...242085&prmenbr
=361
I'd be more concerned about interior axle damage than tire wear.
-Brian
news:10erosjanjgvt72@corp.supernews.com...
: Nope, ball joints tight.
: the axle tube is bent up slightly at end causing top of wheel to be off
by
: said degrees.
:
:
If you are really concerned about it, you could have the axle straightened
(best fix) or you could install an offset ball joint to correct the camber
(band-aid solution):
http://www.jegs.com/cgi-bin/ncommerc...242085&prmenbr
=361
I'd be more concerned about interior axle damage than tire wear.
-Brian
#23
Guest
Posts: n/a
Re: Any Alignment specialist?
"Yellow Fever" <roadrnnr99@REMOVE.yahoo.com> wrote in message
news:10erosjanjgvt72@corp.supernews.com...
: Nope, ball joints tight.
: the axle tube is bent up slightly at end causing top of wheel to be off
by
: said degrees.
:
:
If you are really concerned about it, you could have the axle straightened
(best fix) or you could install an offset ball joint to correct the camber
(band-aid solution):
http://www.jegs.com/cgi-bin/ncommerc...242085&prmenbr
=361
I'd be more concerned about interior axle damage than tire wear.
-Brian
news:10erosjanjgvt72@corp.supernews.com...
: Nope, ball joints tight.
: the axle tube is bent up slightly at end causing top of wheel to be off
by
: said degrees.
:
:
If you are really concerned about it, you could have the axle straightened
(best fix) or you could install an offset ball joint to correct the camber
(band-aid solution):
http://www.jegs.com/cgi-bin/ncommerc...242085&prmenbr
=361
I'd be more concerned about interior axle damage than tire wear.
-Brian
#24
Guest
Posts: n/a
Re: Any Alignment specialist?
"Yellow Fever" <roadrnnr99@REMOVE.yahoo.com> wrote in message
news:10erosjanjgvt72@corp.supernews.com...
: Nope, ball joints tight.
: the axle tube is bent up slightly at end causing top of wheel to be off
by
: said degrees.
:
:
If you are really concerned about it, you could have the axle straightened
(best fix) or you could install an offset ball joint to correct the camber
(band-aid solution):
http://www.jegs.com/cgi-bin/ncommerc...242085&prmenbr
=361
I'd be more concerned about interior axle damage than tire wear.
-Brian
news:10erosjanjgvt72@corp.supernews.com...
: Nope, ball joints tight.
: the axle tube is bent up slightly at end causing top of wheel to be off
by
: said degrees.
:
:
If you are really concerned about it, you could have the axle straightened
(best fix) or you could install an offset ball joint to correct the camber
(band-aid solution):
http://www.jegs.com/cgi-bin/ncommerc...242085&prmenbr
=361
I'd be more concerned about interior axle damage than tire wear.
-Brian
#25
Guest
Posts: n/a
Re: Any Alignment specialist?
"Yellow Fever" <roadrnnr99@REMOVE.yahoo.com> wrote in message
news:10erosjanjgvt72@corp.supernews.com...
: Nope, ball joints tight.
: the axle tube is bent up slightly at end causing top of wheel to be off
by
: said degrees.
:
:
If you are really concerned about it, you could have the axle straightened
(best fix) or you could install an offset ball joint to correct the camber
(band-aid solution):
http://www.jegs.com/cgi-bin/ncommerc...242085&prmenbr
=361
I'd be more concerned about interior axle damage than tire wear.
-Brian
news:10erosjanjgvt72@corp.supernews.com...
: Nope, ball joints tight.
: the axle tube is bent up slightly at end causing top of wheel to be off
by
: said degrees.
:
:
If you are really concerned about it, you could have the axle straightened
(best fix) or you could install an offset ball joint to correct the camber
(band-aid solution):
http://www.jegs.com/cgi-bin/ncommerc...242085&prmenbr
=361
I'd be more concerned about interior axle damage than tire wear.
-Brian
#26
Guest
Posts: n/a
Re: Any Alignment specialist?
No Bill it's the " You have a badly worn ball joint. A lot of us just drive
it, like
it's not going any place like when the Libby's joint fails and the wheel
falls off:"
know it all bull----- responses that get me every time. How the f... do
you know he's got a badly worn ball joint? I think it's helpfull in the
newsgroup when people suggest possible problems and possible solutions, but
I think it's ignorant and arrogant when people like you get on and give
somebody, that may not have much knowledge or experience and is relying on
this group for some sound advise and information, some absolute affirmative
about what there problem is with no basis in fact.
No Bill, http://Steve-Garner.com/ is not my Daddy, that's me. Is this more
of your attempts to bolster your own self-confidence by illustrating that
you know how to do some rudimentary searches on the Web? Wow Bill, very
talented. Are you feeling a little better about yourself now?
"L.W. (ßill) ------ III" <----------@***.net> wrote in message
news:40EE1030.B1833697@***.net...
> Steve did you read the Poster's reply? Now if you'd let him reply
> to my questioning on the position of the bend, and suggesting the
> opposite tire wear, then we could have gone from there. Have you bent
> the tube at the end before?
> Is this your Daddy? http://Steve-Garner.com/
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
> Steve G wrote:
> >
> > Here's L.W. (Bill)again with his absolutely, know better than anyone,
> > without a doubt, you're an idiot, armchair diagnosis. How does he do
it?
> >
> > Let's suppose for a minute that he does actually know how to test a ball
> > joint. Most people with enough knowledge to set up the alignment
equipment
> > and know what a camber reading is are usually smart enough to check the
> > frontend for looseness before strapping on the equipment. So, whether
that
> > was Yellow Fever or his favourite mechanic, they're already way ahead of
you
> > L.W.(Bill) ------ III. Having established that much, it doesn't matter
> > where the bend is along the tube, at the inboard end at the housing or
the
> > outer end of the tube, if it's bending up you will lose camber. A half
of
> > one degree is not enough that you will burn the edge of the tire off in
> > short order. If you rotate the tires a little more frequently you will
> > probably not notice the difference. Personally, I would strap down or
> > somehow anchor the outer end of the tube and put my floor jack under the
> > diff housing right at the entrance of the tube and take the bend out.
If
> > you're not comfortable doing it yourself. any truck alignment shop can
do
> > it, that's exactly how camber is adjusted on solid axles, bending the
axle.
> > Steve g.
it, like
it's not going any place like when the Libby's joint fails and the wheel
falls off:"
know it all bull----- responses that get me every time. How the f... do
you know he's got a badly worn ball joint? I think it's helpfull in the
newsgroup when people suggest possible problems and possible solutions, but
I think it's ignorant and arrogant when people like you get on and give
somebody, that may not have much knowledge or experience and is relying on
this group for some sound advise and information, some absolute affirmative
about what there problem is with no basis in fact.
No Bill, http://Steve-Garner.com/ is not my Daddy, that's me. Is this more
of your attempts to bolster your own self-confidence by illustrating that
you know how to do some rudimentary searches on the Web? Wow Bill, very
talented. Are you feeling a little better about yourself now?
"L.W. (ßill) ------ III" <----------@***.net> wrote in message
news:40EE1030.B1833697@***.net...
> Steve did you read the Poster's reply? Now if you'd let him reply
> to my questioning on the position of the bend, and suggesting the
> opposite tire wear, then we could have gone from there. Have you bent
> the tube at the end before?
> Is this your Daddy? http://Steve-Garner.com/
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
> Steve G wrote:
> >
> > Here's L.W. (Bill)again with his absolutely, know better than anyone,
> > without a doubt, you're an idiot, armchair diagnosis. How does he do
it?
> >
> > Let's suppose for a minute that he does actually know how to test a ball
> > joint. Most people with enough knowledge to set up the alignment
equipment
> > and know what a camber reading is are usually smart enough to check the
> > frontend for looseness before strapping on the equipment. So, whether
that
> > was Yellow Fever or his favourite mechanic, they're already way ahead of
you
> > L.W.(Bill) ------ III. Having established that much, it doesn't matter
> > where the bend is along the tube, at the inboard end at the housing or
the
> > outer end of the tube, if it's bending up you will lose camber. A half
of
> > one degree is not enough that you will burn the edge of the tire off in
> > short order. If you rotate the tires a little more frequently you will
> > probably not notice the difference. Personally, I would strap down or
> > somehow anchor the outer end of the tube and put my floor jack under the
> > diff housing right at the entrance of the tube and take the bend out.
If
> > you're not comfortable doing it yourself. any truck alignment shop can
do
> > it, that's exactly how camber is adjusted on solid axles, bending the
axle.
> > Steve g.
#27
Guest
Posts: n/a
Re: Any Alignment specialist?
No Bill it's the " You have a badly worn ball joint. A lot of us just drive
it, like
it's not going any place like when the Libby's joint fails and the wheel
falls off:"
know it all bull----- responses that get me every time. How the f... do
you know he's got a badly worn ball joint? I think it's helpfull in the
newsgroup when people suggest possible problems and possible solutions, but
I think it's ignorant and arrogant when people like you get on and give
somebody, that may not have much knowledge or experience and is relying on
this group for some sound advise and information, some absolute affirmative
about what there problem is with no basis in fact.
No Bill, http://Steve-Garner.com/ is not my Daddy, that's me. Is this more
of your attempts to bolster your own self-confidence by illustrating that
you know how to do some rudimentary searches on the Web? Wow Bill, very
talented. Are you feeling a little better about yourself now?
"L.W. (ßill) ------ III" <----------@***.net> wrote in message
news:40EE1030.B1833697@***.net...
> Steve did you read the Poster's reply? Now if you'd let him reply
> to my questioning on the position of the bend, and suggesting the
> opposite tire wear, then we could have gone from there. Have you bent
> the tube at the end before?
> Is this your Daddy? http://Steve-Garner.com/
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
> Steve G wrote:
> >
> > Here's L.W. (Bill)again with his absolutely, know better than anyone,
> > without a doubt, you're an idiot, armchair diagnosis. How does he do
it?
> >
> > Let's suppose for a minute that he does actually know how to test a ball
> > joint. Most people with enough knowledge to set up the alignment
equipment
> > and know what a camber reading is are usually smart enough to check the
> > frontend for looseness before strapping on the equipment. So, whether
that
> > was Yellow Fever or his favourite mechanic, they're already way ahead of
you
> > L.W.(Bill) ------ III. Having established that much, it doesn't matter
> > where the bend is along the tube, at the inboard end at the housing or
the
> > outer end of the tube, if it's bending up you will lose camber. A half
of
> > one degree is not enough that you will burn the edge of the tire off in
> > short order. If you rotate the tires a little more frequently you will
> > probably not notice the difference. Personally, I would strap down or
> > somehow anchor the outer end of the tube and put my floor jack under the
> > diff housing right at the entrance of the tube and take the bend out.
If
> > you're not comfortable doing it yourself. any truck alignment shop can
do
> > it, that's exactly how camber is adjusted on solid axles, bending the
axle.
> > Steve g.
it, like
it's not going any place like when the Libby's joint fails and the wheel
falls off:"
know it all bull----- responses that get me every time. How the f... do
you know he's got a badly worn ball joint? I think it's helpfull in the
newsgroup when people suggest possible problems and possible solutions, but
I think it's ignorant and arrogant when people like you get on and give
somebody, that may not have much knowledge or experience and is relying on
this group for some sound advise and information, some absolute affirmative
about what there problem is with no basis in fact.
No Bill, http://Steve-Garner.com/ is not my Daddy, that's me. Is this more
of your attempts to bolster your own self-confidence by illustrating that
you know how to do some rudimentary searches on the Web? Wow Bill, very
talented. Are you feeling a little better about yourself now?
"L.W. (ßill) ------ III" <----------@***.net> wrote in message
news:40EE1030.B1833697@***.net...
> Steve did you read the Poster's reply? Now if you'd let him reply
> to my questioning on the position of the bend, and suggesting the
> opposite tire wear, then we could have gone from there. Have you bent
> the tube at the end before?
> Is this your Daddy? http://Steve-Garner.com/
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
> Steve G wrote:
> >
> > Here's L.W. (Bill)again with his absolutely, know better than anyone,
> > without a doubt, you're an idiot, armchair diagnosis. How does he do
it?
> >
> > Let's suppose for a minute that he does actually know how to test a ball
> > joint. Most people with enough knowledge to set up the alignment
equipment
> > and know what a camber reading is are usually smart enough to check the
> > frontend for looseness before strapping on the equipment. So, whether
that
> > was Yellow Fever or his favourite mechanic, they're already way ahead of
you
> > L.W.(Bill) ------ III. Having established that much, it doesn't matter
> > where the bend is along the tube, at the inboard end at the housing or
the
> > outer end of the tube, if it's bending up you will lose camber. A half
of
> > one degree is not enough that you will burn the edge of the tire off in
> > short order. If you rotate the tires a little more frequently you will
> > probably not notice the difference. Personally, I would strap down or
> > somehow anchor the outer end of the tube and put my floor jack under the
> > diff housing right at the entrance of the tube and take the bend out.
If
> > you're not comfortable doing it yourself. any truck alignment shop can
do
> > it, that's exactly how camber is adjusted on solid axles, bending the
axle.
> > Steve g.
#28
Guest
Posts: n/a
Re: Any Alignment specialist?
No Bill it's the " You have a badly worn ball joint. A lot of us just drive
it, like
it's not going any place like when the Libby's joint fails and the wheel
falls off:"
know it all bull----- responses that get me every time. How the f... do
you know he's got a badly worn ball joint? I think it's helpfull in the
newsgroup when people suggest possible problems and possible solutions, but
I think it's ignorant and arrogant when people like you get on and give
somebody, that may not have much knowledge or experience and is relying on
this group for some sound advise and information, some absolute affirmative
about what there problem is with no basis in fact.
No Bill, http://Steve-Garner.com/ is not my Daddy, that's me. Is this more
of your attempts to bolster your own self-confidence by illustrating that
you know how to do some rudimentary searches on the Web? Wow Bill, very
talented. Are you feeling a little better about yourself now?
"L.W. (ßill) ------ III" <----------@***.net> wrote in message
news:40EE1030.B1833697@***.net...
> Steve did you read the Poster's reply? Now if you'd let him reply
> to my questioning on the position of the bend, and suggesting the
> opposite tire wear, then we could have gone from there. Have you bent
> the tube at the end before?
> Is this your Daddy? http://Steve-Garner.com/
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
> Steve G wrote:
> >
> > Here's L.W. (Bill)again with his absolutely, know better than anyone,
> > without a doubt, you're an idiot, armchair diagnosis. How does he do
it?
> >
> > Let's suppose for a minute that he does actually know how to test a ball
> > joint. Most people with enough knowledge to set up the alignment
equipment
> > and know what a camber reading is are usually smart enough to check the
> > frontend for looseness before strapping on the equipment. So, whether
that
> > was Yellow Fever or his favourite mechanic, they're already way ahead of
you
> > L.W.(Bill) ------ III. Having established that much, it doesn't matter
> > where the bend is along the tube, at the inboard end at the housing or
the
> > outer end of the tube, if it's bending up you will lose camber. A half
of
> > one degree is not enough that you will burn the edge of the tire off in
> > short order. If you rotate the tires a little more frequently you will
> > probably not notice the difference. Personally, I would strap down or
> > somehow anchor the outer end of the tube and put my floor jack under the
> > diff housing right at the entrance of the tube and take the bend out.
If
> > you're not comfortable doing it yourself. any truck alignment shop can
do
> > it, that's exactly how camber is adjusted on solid axles, bending the
axle.
> > Steve g.
it, like
it's not going any place like when the Libby's joint fails and the wheel
falls off:"
know it all bull----- responses that get me every time. How the f... do
you know he's got a badly worn ball joint? I think it's helpfull in the
newsgroup when people suggest possible problems and possible solutions, but
I think it's ignorant and arrogant when people like you get on and give
somebody, that may not have much knowledge or experience and is relying on
this group for some sound advise and information, some absolute affirmative
about what there problem is with no basis in fact.
No Bill, http://Steve-Garner.com/ is not my Daddy, that's me. Is this more
of your attempts to bolster your own self-confidence by illustrating that
you know how to do some rudimentary searches on the Web? Wow Bill, very
talented. Are you feeling a little better about yourself now?
"L.W. (ßill) ------ III" <----------@***.net> wrote in message
news:40EE1030.B1833697@***.net...
> Steve did you read the Poster's reply? Now if you'd let him reply
> to my questioning on the position of the bend, and suggesting the
> opposite tire wear, then we could have gone from there. Have you bent
> the tube at the end before?
> Is this your Daddy? http://Steve-Garner.com/
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
> Steve G wrote:
> >
> > Here's L.W. (Bill)again with his absolutely, know better than anyone,
> > without a doubt, you're an idiot, armchair diagnosis. How does he do
it?
> >
> > Let's suppose for a minute that he does actually know how to test a ball
> > joint. Most people with enough knowledge to set up the alignment
equipment
> > and know what a camber reading is are usually smart enough to check the
> > frontend for looseness before strapping on the equipment. So, whether
that
> > was Yellow Fever or his favourite mechanic, they're already way ahead of
you
> > L.W.(Bill) ------ III. Having established that much, it doesn't matter
> > where the bend is along the tube, at the inboard end at the housing or
the
> > outer end of the tube, if it's bending up you will lose camber. A half
of
> > one degree is not enough that you will burn the edge of the tire off in
> > short order. If you rotate the tires a little more frequently you will
> > probably not notice the difference. Personally, I would strap down or
> > somehow anchor the outer end of the tube and put my floor jack under the
> > diff housing right at the entrance of the tube and take the bend out.
If
> > you're not comfortable doing it yourself. any truck alignment shop can
do
> > it, that's exactly how camber is adjusted on solid axles, bending the
axle.
> > Steve g.
#29
Guest
Posts: n/a
Re: Any Alignment specialist?
No Bill it's the " You have a badly worn ball joint. A lot of us just drive
it, like
it's not going any place like when the Libby's joint fails and the wheel
falls off:"
know it all bull----- responses that get me every time. How the f... do
you know he's got a badly worn ball joint? I think it's helpfull in the
newsgroup when people suggest possible problems and possible solutions, but
I think it's ignorant and arrogant when people like you get on and give
somebody, that may not have much knowledge or experience and is relying on
this group for some sound advise and information, some absolute affirmative
about what there problem is with no basis in fact.
No Bill, http://Steve-Garner.com/ is not my Daddy, that's me. Is this more
of your attempts to bolster your own self-confidence by illustrating that
you know how to do some rudimentary searches on the Web? Wow Bill, very
talented. Are you feeling a little better about yourself now?
"L.W. (ßill) ------ III" <----------@***.net> wrote in message
news:40EE1030.B1833697@***.net...
> Steve did you read the Poster's reply? Now if you'd let him reply
> to my questioning on the position of the bend, and suggesting the
> opposite tire wear, then we could have gone from there. Have you bent
> the tube at the end before?
> Is this your Daddy? http://Steve-Garner.com/
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
> Steve G wrote:
> >
> > Here's L.W. (Bill)again with his absolutely, know better than anyone,
> > without a doubt, you're an idiot, armchair diagnosis. How does he do
it?
> >
> > Let's suppose for a minute that he does actually know how to test a ball
> > joint. Most people with enough knowledge to set up the alignment
equipment
> > and know what a camber reading is are usually smart enough to check the
> > frontend for looseness before strapping on the equipment. So, whether
that
> > was Yellow Fever or his favourite mechanic, they're already way ahead of
you
> > L.W.(Bill) ------ III. Having established that much, it doesn't matter
> > where the bend is along the tube, at the inboard end at the housing or
the
> > outer end of the tube, if it's bending up you will lose camber. A half
of
> > one degree is not enough that you will burn the edge of the tire off in
> > short order. If you rotate the tires a little more frequently you will
> > probably not notice the difference. Personally, I would strap down or
> > somehow anchor the outer end of the tube and put my floor jack under the
> > diff housing right at the entrance of the tube and take the bend out.
If
> > you're not comfortable doing it yourself. any truck alignment shop can
do
> > it, that's exactly how camber is adjusted on solid axles, bending the
axle.
> > Steve g.
it, like
it's not going any place like when the Libby's joint fails and the wheel
falls off:"
know it all bull----- responses that get me every time. How the f... do
you know he's got a badly worn ball joint? I think it's helpfull in the
newsgroup when people suggest possible problems and possible solutions, but
I think it's ignorant and arrogant when people like you get on and give
somebody, that may not have much knowledge or experience and is relying on
this group for some sound advise and information, some absolute affirmative
about what there problem is with no basis in fact.
No Bill, http://Steve-Garner.com/ is not my Daddy, that's me. Is this more
of your attempts to bolster your own self-confidence by illustrating that
you know how to do some rudimentary searches on the Web? Wow Bill, very
talented. Are you feeling a little better about yourself now?
"L.W. (ßill) ------ III" <----------@***.net> wrote in message
news:40EE1030.B1833697@***.net...
> Steve did you read the Poster's reply? Now if you'd let him reply
> to my questioning on the position of the bend, and suggesting the
> opposite tire wear, then we could have gone from there. Have you bent
> the tube at the end before?
> Is this your Daddy? http://Steve-Garner.com/
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
> Steve G wrote:
> >
> > Here's L.W. (Bill)again with his absolutely, know better than anyone,
> > without a doubt, you're an idiot, armchair diagnosis. How does he do
it?
> >
> > Let's suppose for a minute that he does actually know how to test a ball
> > joint. Most people with enough knowledge to set up the alignment
equipment
> > and know what a camber reading is are usually smart enough to check the
> > frontend for looseness before strapping on the equipment. So, whether
that
> > was Yellow Fever or his favourite mechanic, they're already way ahead of
you
> > L.W.(Bill) ------ III. Having established that much, it doesn't matter
> > where the bend is along the tube, at the inboard end at the housing or
the
> > outer end of the tube, if it's bending up you will lose camber. A half
of
> > one degree is not enough that you will burn the edge of the tire off in
> > short order. If you rotate the tires a little more frequently you will
> > probably not notice the difference. Personally, I would strap down or
> > somehow anchor the outer end of the tube and put my floor jack under the
> > diff housing right at the entrance of the tube and take the bend out.
If
> > you're not comfortable doing it yourself. any truck alignment shop can
do
> > it, that's exactly how camber is adjusted on solid axles, bending the
axle.
> > Steve g.
#30
Guest
Posts: n/a
Re: Any Alignment specialist?
Geez................chill out. This is a group of individuals - read & reply
to what ever you enjoy.........if you don't like something - reply in a
civilized manor or ignore it. Flying off the handle like this is not healthy
for you & is not a contribution to the group.
--
Carlo F. Serusa, Jr. RPh
carlo.jr at comcast DOTnet
'98 Sahara TJ - '89 YJ - '79 Scout II
O|||||||O
'92 Explorer '65 Mustang
"Steve G" <NospamforSteve@Steve-Garner.com> wrote in message
news:kBxHc.987896$Pk3.103684@pd7tw1no...
> No Bill it's the " You have a badly worn ball joint. A lot of us just
drive
> it, like
> it's not going any place like when the Libby's joint fails and the wheel
> falls off:"
> know it all bull----- responses that get me every time. How the f... do
> you know he's got a badly worn ball joint? I think it's helpfull in the
> newsgroup when people suggest possible problems and possible solutions,
but
> I think it's ignorant and arrogant when people like you get on and give
> somebody, that may not have much knowledge or experience and is relying on
> this group for some sound advise and information, some absolute
affirmative
> about what there problem is with no basis in fact.
>
> No Bill, http://Steve-Garner.com/ is not my Daddy, that's me. Is this
more
> of your attempts to bolster your own self-confidence by illustrating that
> you know how to do some rudimentary searches on the Web? Wow Bill, very
> talented. Are you feeling a little better about yourself now?
>
>
> "L.W. (ßill) ------ III" <----------@***.net> wrote in message
> news:40EE1030.B1833697@***.net...
> > Steve did you read the Poster's reply? Now if you'd let him reply
> > to my questioning on the position of the bend, and suggesting the
> > opposite tire wear, then we could have gone from there. Have you bent
> > the tube at the end before?
> > Is this your Daddy? http://Steve-Garner.com/
> > God Bless America, ßill O|||||||O
> > mailto:-------------------- http://www.----------.com/
> >
> > Steve G wrote:
> > >
> > > Here's L.W. (Bill)again with his absolutely, know better than anyone,
> > > without a doubt, you're an idiot, armchair diagnosis. How does he do
> it?
> > >
> > > Let's suppose for a minute that he does actually know how to test a
ball
> > > joint. Most people with enough knowledge to set up the alignment
> equipment
> > > and know what a camber reading is are usually smart enough to check
the
> > > frontend for looseness before strapping on the equipment. So, whether
> that
> > > was Yellow Fever or his favourite mechanic, they're already way ahead
of
> you
> > > L.W.(Bill) ------ III. Having established that much, it doesn't
matter
> > > where the bend is along the tube, at the inboard end at the housing or
> the
> > > outer end of the tube, if it's bending up you will lose camber. A
half
> of
> > > one degree is not enough that you will burn the edge of the tire off
in
> > > short order. If you rotate the tires a little more frequently you
will
> > > probably not notice the difference. Personally, I would strap down or
> > > somehow anchor the outer end of the tube and put my floor jack under
the
> > > diff housing right at the entrance of the tube and take the bend out.
> If
> > > you're not comfortable doing it yourself. any truck alignment shop can
> do
> > > it, that's exactly how camber is adjusted on solid axles, bending the
> axle.
> > > Steve g.
>
>
to what ever you enjoy.........if you don't like something - reply in a
civilized manor or ignore it. Flying off the handle like this is not healthy
for you & is not a contribution to the group.
--
Carlo F. Serusa, Jr. RPh
carlo.jr at comcast DOTnet
'98 Sahara TJ - '89 YJ - '79 Scout II
O|||||||O
'92 Explorer '65 Mustang
"Steve G" <NospamforSteve@Steve-Garner.com> wrote in message
news:kBxHc.987896$Pk3.103684@pd7tw1no...
> No Bill it's the " You have a badly worn ball joint. A lot of us just
drive
> it, like
> it's not going any place like when the Libby's joint fails and the wheel
> falls off:"
> know it all bull----- responses that get me every time. How the f... do
> you know he's got a badly worn ball joint? I think it's helpfull in the
> newsgroup when people suggest possible problems and possible solutions,
but
> I think it's ignorant and arrogant when people like you get on and give
> somebody, that may not have much knowledge or experience and is relying on
> this group for some sound advise and information, some absolute
affirmative
> about what there problem is with no basis in fact.
>
> No Bill, http://Steve-Garner.com/ is not my Daddy, that's me. Is this
more
> of your attempts to bolster your own self-confidence by illustrating that
> you know how to do some rudimentary searches on the Web? Wow Bill, very
> talented. Are you feeling a little better about yourself now?
>
>
> "L.W. (ßill) ------ III" <----------@***.net> wrote in message
> news:40EE1030.B1833697@***.net...
> > Steve did you read the Poster's reply? Now if you'd let him reply
> > to my questioning on the position of the bend, and suggesting the
> > opposite tire wear, then we could have gone from there. Have you bent
> > the tube at the end before?
> > Is this your Daddy? http://Steve-Garner.com/
> > God Bless America, ßill O|||||||O
> > mailto:-------------------- http://www.----------.com/
> >
> > Steve G wrote:
> > >
> > > Here's L.W. (Bill)again with his absolutely, know better than anyone,
> > > without a doubt, you're an idiot, armchair diagnosis. How does he do
> it?
> > >
> > > Let's suppose for a minute that he does actually know how to test a
ball
> > > joint. Most people with enough knowledge to set up the alignment
> equipment
> > > and know what a camber reading is are usually smart enough to check
the
> > > frontend for looseness before strapping on the equipment. So, whether
> that
> > > was Yellow Fever or his favourite mechanic, they're already way ahead
of
> you
> > > L.W.(Bill) ------ III. Having established that much, it doesn't
matter
> > > where the bend is along the tube, at the inboard end at the housing or
> the
> > > outer end of the tube, if it's bending up you will lose camber. A
half
> of
> > > one degree is not enough that you will burn the edge of the tire off
in
> > > short order. If you rotate the tires a little more frequently you
will
> > > probably not notice the difference. Personally, I would strap down or
> > > somehow anchor the outer end of the tube and put my floor jack under
the
> > > diff housing right at the entrance of the tube and take the bend out.
> If
> > > you're not comfortable doing it yourself. any truck alignment shop can
> do
> > > it, that's exactly how camber is adjusted on solid axles, bending the
> axle.
> > > Steve g.
>
>