Re: 93 jeep cherokee clutch soft
New or rebuilt?
Brands? "Mike Romain" <romainm@sympatico.ca> wrote in message news:45d72233$0$23397$9a6e19ea@unlimited.newshosti ng.com... >5 out of the last 7 or 8 master cylinders I have seen were bad out of the >box. They all leaked where the pedal shaft enters the cylinder. Thankfully >we bench bled them so I spotted the leaks before we installed them. > > Mike > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > 88 Cherokee 235 BFG AT's > Canadian Off Road Trips Photos: Non members can still view! > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 > (More Off Road album links at bottom of the view page) > > grizfan16@msn.com wrote: >> I have a 93 jeep 4.0 5spd when I push in the clutch it won't disengage >> the clutch until the very bottom and reengages right away. If i out >> driving it hard the fluid level falls and i lose clutch but i can't >> find a leak It has a new master in it any help would be great >> |
Re: 93 jeep cherokee clutch soft
New or rebuilt?
Brands? "Mike Romain" <romainm@sympatico.ca> wrote in message news:45d72233$0$23397$9a6e19ea@unlimited.newshosti ng.com... >5 out of the last 7 or 8 master cylinders I have seen were bad out of the >box. They all leaked where the pedal shaft enters the cylinder. Thankfully >we bench bled them so I spotted the leaks before we installed them. > > Mike > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > 88 Cherokee 235 BFG AT's > Canadian Off Road Trips Photos: Non members can still view! > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 > (More Off Road album links at bottom of the view page) > > grizfan16@msn.com wrote: >> I have a 93 jeep 4.0 5spd when I push in the clutch it won't disengage >> the clutch until the very bottom and reengages right away. If i out >> driving it hard the fluid level falls and i lose clutch but i can't >> find a leak It has a new master in it any help would be great >> |
Re: 93 jeep cherokee clutch soft
i've been through three masters and three slaves (all different
occasions) in the four years I've had my YJ. aftermarket parts just don't hold up like the OEMs. at one point, my local mechanic installed a plastic slave and within a month it had developed a horrible clutch chatter. at another point, I had hydraulic fluid leaking down the clutch pedal and onto my floormat. If you have a 4.0, you should have the AX-15, which, if I recall correctly, has an external slave cylinder. check that. the few weeks before my slave cylinder completely bit the dust were hell. I had to bleed the line every day in the parking lot before I left school just to get home. by the end, i was taking the backroads in 1st gear because I couldn't get the clutch to disengage more than once after i bled the line. |
Re: 93 jeep cherokee clutch soft
i've been through three masters and three slaves (all different
occasions) in the four years I've had my YJ. aftermarket parts just don't hold up like the OEMs. at one point, my local mechanic installed a plastic slave and within a month it had developed a horrible clutch chatter. at another point, I had hydraulic fluid leaking down the clutch pedal and onto my floormat. If you have a 4.0, you should have the AX-15, which, if I recall correctly, has an external slave cylinder. check that. the few weeks before my slave cylinder completely bit the dust were hell. I had to bleed the line every day in the parking lot before I left school just to get home. by the end, i was taking the backroads in 1st gear because I couldn't get the clutch to disengage more than once after i bled the line. |
Re: 93 jeep cherokee clutch soft
i've been through three masters and three slaves (all different
occasions) in the four years I've had my YJ. aftermarket parts just don't hold up like the OEMs. at one point, my local mechanic installed a plastic slave and within a month it had developed a horrible clutch chatter. at another point, I had hydraulic fluid leaking down the clutch pedal and onto my floormat. If you have a 4.0, you should have the AX-15, which, if I recall correctly, has an external slave cylinder. check that. the few weeks before my slave cylinder completely bit the dust were hell. I had to bleed the line every day in the parking lot before I left school just to get home. by the end, i was taking the backroads in 1st gear because I couldn't get the clutch to disengage more than once after i bled the line. |
Re: 93 jeep cherokee clutch soft
Heh, my YJ is going on 13 and still has the original clutch hydraulics.
Knock, knock. The internal slave cylinder is pre-1994 as far as I know. Anything 1994 and later will have the external design. This applies to both the 4 and 6 cylinder engines. If you still have the internal design, Advance Adapters says that cleanliness is essential when servicing this unit. Steam cleaning the inside of the bell housing would be appropriate. It may be possible to retrofit the later external slave bell housing too. Earle "Micah" <mgoodenbour@gmail.com> wrote in message news:1171935934.651180.308200@t69g2000cwt.googlegr oups.com... > i've been through three masters and three slaves (all different > occasions) in the four years I've had my YJ. aftermarket parts just > don't hold up like the OEMs. at one point, my local mechanic > installed a plastic slave and within a month it had developed a > horrible clutch chatter. at another point, I had hydraulic fluid > leaking down the clutch pedal and onto my floormat. > > If you have a 4.0, you should have the AX-15, which, if I recall > correctly, has an external slave cylinder. check that. > > the few weeks before my slave cylinder completely bit the dust were > hell. I had to bleed the line every day in the parking lot before I > left school just to get home. by the end, i was taking the backroads > in 1st gear because I couldn't get the clutch to disengage more than > once after i bled the line. > |
Re: 93 jeep cherokee clutch soft
Heh, my YJ is going on 13 and still has the original clutch hydraulics.
Knock, knock. The internal slave cylinder is pre-1994 as far as I know. Anything 1994 and later will have the external design. This applies to both the 4 and 6 cylinder engines. If you still have the internal design, Advance Adapters says that cleanliness is essential when servicing this unit. Steam cleaning the inside of the bell housing would be appropriate. It may be possible to retrofit the later external slave bell housing too. Earle "Micah" <mgoodenbour@gmail.com> wrote in message news:1171935934.651180.308200@t69g2000cwt.googlegr oups.com... > i've been through three masters and three slaves (all different > occasions) in the four years I've had my YJ. aftermarket parts just > don't hold up like the OEMs. at one point, my local mechanic > installed a plastic slave and within a month it had developed a > horrible clutch chatter. at another point, I had hydraulic fluid > leaking down the clutch pedal and onto my floormat. > > If you have a 4.0, you should have the AX-15, which, if I recall > correctly, has an external slave cylinder. check that. > > the few weeks before my slave cylinder completely bit the dust were > hell. I had to bleed the line every day in the parking lot before I > left school just to get home. by the end, i was taking the backroads > in 1st gear because I couldn't get the clutch to disengage more than > once after i bled the line. > |
Re: 93 jeep cherokee clutch soft
Heh, my YJ is going on 13 and still has the original clutch hydraulics.
Knock, knock. The internal slave cylinder is pre-1994 as far as I know. Anything 1994 and later will have the external design. This applies to both the 4 and 6 cylinder engines. If you still have the internal design, Advance Adapters says that cleanliness is essential when servicing this unit. Steam cleaning the inside of the bell housing would be appropriate. It may be possible to retrofit the later external slave bell housing too. Earle "Micah" <mgoodenbour@gmail.com> wrote in message news:1171935934.651180.308200@t69g2000cwt.googlegr oups.com... > i've been through three masters and three slaves (all different > occasions) in the four years I've had my YJ. aftermarket parts just > don't hold up like the OEMs. at one point, my local mechanic > installed a plastic slave and within a month it had developed a > horrible clutch chatter. at another point, I had hydraulic fluid > leaking down the clutch pedal and onto my floormat. > > If you have a 4.0, you should have the AX-15, which, if I recall > correctly, has an external slave cylinder. check that. > > the few weeks before my slave cylinder completely bit the dust were > hell. I had to bleed the line every day in the parking lot before I > left school just to get home. by the end, i was taking the backroads > in 1st gear because I couldn't get the clutch to disengage more than > once after i bled the line. > |
Re: 93 jeep cherokee clutch soft
I've replaced my master and slave once each in the five years I've had
my '93. Thank the lord, too, the internal slave is a PITA. Actually, just spent pretty much all day Sunday replacing the clutch in the '89. Rusty bolts and 20* temperatures make for a fun day. As Earle said, the external slave retrofit has been done. I've seen a write-up or two, I just don't remember where. Earle Horton wrote: > Heh, my YJ is going on 13 and still has the original clutch hydraulics. > Knock, knock. The internal slave cylinder is pre-1994 as far as I know. > Anything 1994 and later will have the external design. This applies to both > the 4 and 6 cylinder engines. If you still have the internal design, > Advance Adapters says that cleanliness is essential when servicing this > unit. Steam cleaning the inside of the bell housing would be appropriate. > It may be possible to retrofit the later external slave bell housing too. > > Earle > > "Micah" <mgoodenbour@gmail.com> wrote in message > news:1171935934.651180.308200@t69g2000cwt.googlegr oups.com... >> i've been through three masters and three slaves (all different >> occasions) in the four years I've had my YJ. aftermarket parts just >> don't hold up like the OEMs. at one point, my local mechanic >> installed a plastic slave and within a month it had developed a >> horrible clutch chatter. at another point, I had hydraulic fluid >> leaking down the clutch pedal and onto my floormat. >> >> If you have a 4.0, you should have the AX-15, which, if I recall >> correctly, has an external slave cylinder. check that. >> >> the few weeks before my slave cylinder completely bit the dust were >> hell. I had to bleed the line every day in the parking lot before I >> left school just to get home. by the end, i was taking the backroads >> in 1st gear because I couldn't get the clutch to disengage more than >> once after i bled the line. >> > > |
Re: 93 jeep cherokee clutch soft
I've replaced my master and slave once each in the five years I've had
my '93. Thank the lord, too, the internal slave is a PITA. Actually, just spent pretty much all day Sunday replacing the clutch in the '89. Rusty bolts and 20* temperatures make for a fun day. As Earle said, the external slave retrofit has been done. I've seen a write-up or two, I just don't remember where. Earle Horton wrote: > Heh, my YJ is going on 13 and still has the original clutch hydraulics. > Knock, knock. The internal slave cylinder is pre-1994 as far as I know. > Anything 1994 and later will have the external design. This applies to both > the 4 and 6 cylinder engines. If you still have the internal design, > Advance Adapters says that cleanliness is essential when servicing this > unit. Steam cleaning the inside of the bell housing would be appropriate. > It may be possible to retrofit the later external slave bell housing too. > > Earle > > "Micah" <mgoodenbour@gmail.com> wrote in message > news:1171935934.651180.308200@t69g2000cwt.googlegr oups.com... >> i've been through three masters and three slaves (all different >> occasions) in the four years I've had my YJ. aftermarket parts just >> don't hold up like the OEMs. at one point, my local mechanic >> installed a plastic slave and within a month it had developed a >> horrible clutch chatter. at another point, I had hydraulic fluid >> leaking down the clutch pedal and onto my floormat. >> >> If you have a 4.0, you should have the AX-15, which, if I recall >> correctly, has an external slave cylinder. check that. >> >> the few weeks before my slave cylinder completely bit the dust were >> hell. I had to bleed the line every day in the parking lot before I >> left school just to get home. by the end, i was taking the backroads >> in 1st gear because I couldn't get the clutch to disengage more than >> once after i bled the line. >> > > |
All times are GMT -4. The time now is 06:56 PM. |
© 2024 MH Sub I, LLC dba Internet Brands