Jeeps Canada - Jeep Forums - What Did You Do To Your GC Today

Page 13 of 122

Show 40 post(s) from this thread on one page

Jeeps Canada - Jeep Forums (https://www.jeepscanada.com/)

- Jeep Grand Cherokee Forum (https://www.jeepscanada.com/jeep-grand-cherokee-forum-23/)

- - What Did You Do To Your GC Today (https://www.jeepscanada.com/jeep-grand-cherokee-forum-23/what-did-you-do-your-gc-today-91591/)

Jared

04-23-2009 06:52 PM

Re: What Did You Do To Your GC Today

I got the oextra o2s by standard. 2 days after the replacement for the defective sensor was installed it threw a cel again so I ordered an ngk one, going to install it today. I gotta order a bunch of suspension bushings because I foulf out that both the ones for the passenger front upper control arm are worn to hell, you can grab the control arm and move it back and forth about an inch.

04WJGuy

04-24-2009 01:09 AM

Re: What Did You Do To Your GC Today

Surprised your not getting death wobble with them being that worn, your not replacing them with poly bushings are you?

04WJGuy

04-24-2009 12:05 PM

Re: What Did You Do To Your GC Today

Quote:

Originally Posted by CrazyWJ242 (Post 523961)

hey dan, what kinda exhaust modifications am i going to need to clear the back axle with a bunch of lift, few weeks till 2", then end of summer its going way up to 6" wondering since i have to get some piping done, can i just do it now...

or got a link to a pic of the modified exhaust going over the axle, tube diameter is going to be 2.5" (since the stock shrinks down to 2.25" or smaller...

If you going to be going to 6" soon save the money and just put a downturn pipe after the muffler and tip it towards the passenger side. Make sure it's not pointing straight down, the heat will collect under the Jeep and start heating up the gas tank.
You can get away with the tail pipe up to 4" but with long arms it's just cheaper to turn it down and out.

Jared

04-24-2009 09:51 PM

Re: What Did You Do To Your GC Today

Quote:

Originally Posted by 04WJGuy (Post 524013)

Surprised your not getting death wobble with them being that worn, your not replacing them with poly bushings are you?

Nope just replacing them with stock. Does anyone know if they are the same bushings on the body side as the diff side on the front uppers?

04WJGuy

04-25-2009 12:24 PM

Re: What Did You Do To Your GC Today

The axle side uses M14x2 and the sill side uses M10x1.5, I'm pretty sure the OD of the bushing is the same but the bolt hole is different as you can see.

Jared

04-25-2009 04:40 PM

Re: What Did You Do To Your GC Today

Thx you just saved me a bunch of trouble lol. So ill have to order a new control arm and then a bushing for the axle side, shouldn't be too bad I've seen the arms with bushings for about 25 bucks each. Also I'm on my third o2 sensor, this time ngk and the same code came back again so I guess I'm going to have to look for a short in the harness :(

04WJGuy

04-25-2009 05:21 PM

Re: What Did You Do To Your GC Today

Jared, which one are you replacing?

Jared

04-25-2009 06:52 PM

Re: What Did You Do To Your GC Today

I need the front upper on the pass side

04WJGuy

04-26-2009 12:06 AM

Re: What Did You Do To Your GC Today

Sorry, I meant the o2 sensor. oops