I don't know, but there are lots of calculators on the 'net. When you find
one, set the mount so that the appropriate number aligns to the mark on the
case.



"Carl" <carlsaiyed@REMOVE.hotmail.com> wrote in message
news:KqmdnVWL5Oj5JcjeRVn-rQ@comcast.com...
> What number is correct for 4.10's turning 33's?
>
> Carl
>
> "Jeff Strickland" <crwlr@yahoo.com> wrote in message
> news:8dOdnQNu6Y7OtcjeRVn-rg@ez2.net...
>>
>> "Carl" <carlsaiyed@REMOVE.hotmail.com> wrote in message
>> news:oOidncI8P-LYycnenZ2dnUVZ_s-dnZ2d@comcast.com...
>>> Finally getting around to fixing all the little things on my 89 SOA YJ
>>> that have been bugging me. Got the winch motor rebuilt (twice!) and
>>> installed, got my CB installed, ect. Last two on my list for now..
>>>
>>> Speedometer- I installed a Tom Wood SYE kit per the instructions. The
>>> speedo never worked after that. I tried rotating the adjuster 90 degrees
>>> where the cable goes into the t-case. No luck. What tooth count gear do
>>> I need for for 4.10's turning 33's? How do I properly install it so it
>>> actually *works*?
>>>
>>
>>
>> When you have the speedo gear off and in your hand, you should see
>> numbers around the edge of the housing. These numbers correspond to the
>> number of teeth on the gear. There is an arrow on the transfer case that
>> you align the appropriate number too.
>>
>>
>>
>>
>>> The soft top snaps behind the windshield running on the black bars that
>>> run paralell to the roll bars off the windshield, above the doors. The
>>> soft top snaps to these rails by 5(?) snaps. The snaps don't seem so
>>> "snappy" anymore. They are difficult to get together.. I basically have
>>> to smack them with the heel of my hand. After I get them together, they
>>> seperate easily, causing a pretty irritating noise. There is some mud on
>>> them, I tried cleaning it out and it didn't help. I'm considering
>>> gorilla glueing these..
>>>
>>
>> Have you considered putting oil on the snaps?
>>
>>
>>
>>
>>
>
>

 

I don't know, but there are lots of calculators on the 'net. When you find
one, set the mount so that the appropriate number aligns to the mark on the
case.



"Carl" <carlsaiyed@REMOVE.hotmail.com> wrote in message
news:KqmdnVWL5Oj5JcjeRVn-rQ@comcast.com...
> What number is correct for 4.10's turning 33's?
>
> Carl
>
> "Jeff Strickland" <crwlr@yahoo.com> wrote in message
> news:8dOdnQNu6Y7OtcjeRVn-rg@ez2.net...
>>
>> "Carl" <carlsaiyed@REMOVE.hotmail.com> wrote in message
>> news:oOidncI8P-LYycnenZ2dnUVZ_s-dnZ2d@comcast.com...
>>> Finally getting around to fixing all the little things on my 89 SOA YJ
>>> that have been bugging me. Got the winch motor rebuilt (twice!) and
>>> installed, got my CB installed, ect. Last two on my list for now..
>>>
>>> Speedometer- I installed a Tom Wood SYE kit per the instructions. The
>>> speedo never worked after that. I tried rotating the adjuster 90 degrees
>>> where the cable goes into the t-case. No luck. What tooth count gear do
>>> I need for for 4.10's turning 33's? How do I properly install it so it
>>> actually *works*?
>>>
>>
>>
>> When you have the speedo gear off and in your hand, you should see
>> numbers around the edge of the housing. These numbers correspond to the
>> number of teeth on the gear. There is an arrow on the transfer case that
>> you align the appropriate number too.
>>
>>
>>
>>
>>> The soft top snaps behind the windshield running on the black bars that
>>> run paralell to the roll bars off the windshield, above the doors. The
>>> soft top snaps to these rails by 5(?) snaps. The snaps don't seem so
>>> "snappy" anymore. They are difficult to get together.. I basically have
>>> to smack them with the heel of my hand. After I get them together, they
>>> seperate easily, causing a pretty irritating noise. There is some mud on
>>> them, I tried cleaning it out and it didn't help. I'm considering
>>> gorilla glueing these..
>>>
>>
>> Have you considered putting oil on the snaps?
>>
>>
>>
>>
>>
>
>

 

I don't know, but there are lots of calculators on the 'net. When you find
one, set the mount so that the appropriate number aligns to the mark on the
case.



"Carl" <carlsaiyed@REMOVE.hotmail.com> wrote in message
news:KqmdnVWL5Oj5JcjeRVn-rQ@comcast.com...
> What number is correct for 4.10's turning 33's?
>
> Carl
>
> "Jeff Strickland" <crwlr@yahoo.com> wrote in message
> news:8dOdnQNu6Y7OtcjeRVn-rg@ez2.net...
>>
>> "Carl" <carlsaiyed@REMOVE.hotmail.com> wrote in message
>> news:oOidncI8P-LYycnenZ2dnUVZ_s-dnZ2d@comcast.com...
>>> Finally getting around to fixing all the little things on my 89 SOA YJ
>>> that have been bugging me. Got the winch motor rebuilt (twice!) and
>>> installed, got my CB installed, ect. Last two on my list for now..
>>>
>>> Speedometer- I installed a Tom Wood SYE kit per the instructions. The
>>> speedo never worked after that. I tried rotating the adjuster 90 degrees
>>> where the cable goes into the t-case. No luck. What tooth count gear do
>>> I need for for 4.10's turning 33's? How do I properly install it so it
>>> actually *works*?
>>>
>>
>>
>> When you have the speedo gear off and in your hand, you should see
>> numbers around the edge of the housing. These numbers correspond to the
>> number of teeth on the gear. There is an arrow on the transfer case that
>> you align the appropriate number too.
>>
>>
>>
>>
>>> The soft top snaps behind the windshield running on the black bars that
>>> run paralell to the roll bars off the windshield, above the doors. The
>>> soft top snaps to these rails by 5(?) snaps. The snaps don't seem so
>>> "snappy" anymore. They are difficult to get together.. I basically have
>>> to smack them with the heel of my hand. After I get them together, they
>>> seperate easily, causing a pretty irritating noise. There is some mud on
>>> them, I tried cleaning it out and it didn't help. I'm considering
>>> gorilla glueing these..
>>>
>>
>> Have you considered putting oil on the snaps?
>>
>>
>>
>>
>>
>
>