YJ slave cylinder
#21
Guest
Posts: n/a
Re: YJ slave cylinder
I suggested that to Carl Bill, but cost and timing restraints were liminting
his resourses at the time. I spoke with Carl on the phone, apparently there
is fluid on top of his transmission, according to him. I suggested to him
that it might be a possibility that the bleeder was a little loose.......
(hoping). Not sure where the bleeder is on the 4 banger. he says after the
failure, he refilled and can't find any leakage after someone pumped it 150
times......
Sooooooo
I suggested to him to refill it, and keep some fluid with him and check it
often until the problem area either showes itself or he replaces the slave....
......
L.W.(ßill) ------ III wrote:
>Hi Carl,
> As Earle suggested the other day you need the newer bellhousing to
>fit your AX5 to make the conversion to an external slave. You may see
>why yours failed as the loose straps in the picture hold the slave
>collapsed until it's held by it's limitations inside the housing. I
>would say it would be smart to start with a new slave each time it comes
>apart: http://www.----------.com/YJslave.jpg
> God Bless America, ßill O|||||||O
>mailto:--------------------
>
>> Well, the slave cylinder died on my YJ today. Will the slave out of an AX15
>> fit my AX5?
>>
>> Carl
--
Message posted via CarKB.com
http://www.carkb.com/Uwe/Forums.aspx/jeep-cars/200508/1
his resourses at the time. I spoke with Carl on the phone, apparently there
is fluid on top of his transmission, according to him. I suggested to him
that it might be a possibility that the bleeder was a little loose.......
(hoping). Not sure where the bleeder is on the 4 banger. he says after the
failure, he refilled and can't find any leakage after someone pumped it 150
times......
Sooooooo
I suggested to him to refill it, and keep some fluid with him and check it
often until the problem area either showes itself or he replaces the slave....
......
L.W.(ßill) ------ III wrote:
>Hi Carl,
> As Earle suggested the other day you need the newer bellhousing to
>fit your AX5 to make the conversion to an external slave. You may see
>why yours failed as the loose straps in the picture hold the slave
>collapsed until it's held by it's limitations inside the housing. I
>would say it would be smart to start with a new slave each time it comes
>apart: http://www.----------.com/YJslave.jpg
> God Bless America, ßill O|||||||O
>mailto:--------------------
>
>> Well, the slave cylinder died on my YJ today. Will the slave out of an AX15
>> fit my AX5?
>>
>> Carl
--
Message posted via CarKB.com
http://www.carkb.com/Uwe/Forums.aspx/jeep-cars/200508/1
#22
Guest
Posts: n/a
Re: YJ slave cylinder
also, speaking with Carl, he ordered a new throwout bearing, but they sent
him the wrong one, not the slave/bearing showed in your photo. Sooooooo
he was forced to use the old one.........
L.W.(ßill) ------ III wrote:
>Hi Carl,
> As Earle suggested the other day you need the newer bellhousing to
>fit your AX5 to make the conversion to an external slave. You may see
>why yours failed as the loose straps in the picture hold the slave
>collapsed until it's held by it's limitations inside the housing. I
>would say it would be smart to start with a new slave each time it comes
>apart: http://www.----------.com/YJslave.jpg
> God Bless America, ßill O|||||||O
>mailto:--------------------
>
>> Well, the slave cylinder died on my YJ today. Will the slave out of an AX15
>> fit my AX5?
>>
>> Carl
--
Message posted via CarKB.com
http://www.carkb.com/Uwe/Forums.aspx/jeep-cars/200508/1
him the wrong one, not the slave/bearing showed in your photo. Sooooooo
he was forced to use the old one.........
L.W.(ßill) ------ III wrote:
>Hi Carl,
> As Earle suggested the other day you need the newer bellhousing to
>fit your AX5 to make the conversion to an external slave. You may see
>why yours failed as the loose straps in the picture hold the slave
>collapsed until it's held by it's limitations inside the housing. I
>would say it would be smart to start with a new slave each time it comes
>apart: http://www.----------.com/YJslave.jpg
> God Bless America, ßill O|||||||O
>mailto:--------------------
>
>> Well, the slave cylinder died on my YJ today. Will the slave out of an AX15
>> fit my AX5?
>>
>> Carl
--
Message posted via CarKB.com
http://www.carkb.com/Uwe/Forums.aspx/jeep-cars/200508/1
#23
Guest
Posts: n/a
Re: YJ slave cylinder
also, speaking with Carl, he ordered a new throwout bearing, but they sent
him the wrong one, not the slave/bearing showed in your photo. Sooooooo
he was forced to use the old one.........
L.W.(ßill) ------ III wrote:
>Hi Carl,
> As Earle suggested the other day you need the newer bellhousing to
>fit your AX5 to make the conversion to an external slave. You may see
>why yours failed as the loose straps in the picture hold the slave
>collapsed until it's held by it's limitations inside the housing. I
>would say it would be smart to start with a new slave each time it comes
>apart: http://www.----------.com/YJslave.jpg
> God Bless America, ßill O|||||||O
>mailto:--------------------
>
>> Well, the slave cylinder died on my YJ today. Will the slave out of an AX15
>> fit my AX5?
>>
>> Carl
--
Message posted via CarKB.com
http://www.carkb.com/Uwe/Forums.aspx/jeep-cars/200508/1
him the wrong one, not the slave/bearing showed in your photo. Sooooooo
he was forced to use the old one.........
L.W.(ßill) ------ III wrote:
>Hi Carl,
> As Earle suggested the other day you need the newer bellhousing to
>fit your AX5 to make the conversion to an external slave. You may see
>why yours failed as the loose straps in the picture hold the slave
>collapsed until it's held by it's limitations inside the housing. I
>would say it would be smart to start with a new slave each time it comes
>apart: http://www.----------.com/YJslave.jpg
> God Bless America, ßill O|||||||O
>mailto:--------------------
>
>> Well, the slave cylinder died on my YJ today. Will the slave out of an AX15
>> fit my AX5?
>>
>> Carl
--
Message posted via CarKB.com
http://www.carkb.com/Uwe/Forums.aspx/jeep-cars/200508/1
#24
Guest
Posts: n/a
Re: YJ slave cylinder
also, speaking with Carl, he ordered a new throwout bearing, but they sent
him the wrong one, not the slave/bearing showed in your photo. Sooooooo
he was forced to use the old one.........
L.W.(ßill) ------ III wrote:
>Hi Carl,
> As Earle suggested the other day you need the newer bellhousing to
>fit your AX5 to make the conversion to an external slave. You may see
>why yours failed as the loose straps in the picture hold the slave
>collapsed until it's held by it's limitations inside the housing. I
>would say it would be smart to start with a new slave each time it comes
>apart: http://www.----------.com/YJslave.jpg
> God Bless America, ßill O|||||||O
>mailto:--------------------
>
>> Well, the slave cylinder died on my YJ today. Will the slave out of an AX15
>> fit my AX5?
>>
>> Carl
--
Message posted via CarKB.com
http://www.carkb.com/Uwe/Forums.aspx/jeep-cars/200508/1
him the wrong one, not the slave/bearing showed in your photo. Sooooooo
he was forced to use the old one.........
L.W.(ßill) ------ III wrote:
>Hi Carl,
> As Earle suggested the other day you need the newer bellhousing to
>fit your AX5 to make the conversion to an external slave. You may see
>why yours failed as the loose straps in the picture hold the slave
>collapsed until it's held by it's limitations inside the housing. I
>would say it would be smart to start with a new slave each time it comes
>apart: http://www.----------.com/YJslave.jpg
> God Bless America, ßill O|||||||O
>mailto:--------------------
>
>> Well, the slave cylinder died on my YJ today. Will the slave out of an AX15
>> fit my AX5?
>>
>> Carl
--
Message posted via CarKB.com
http://www.carkb.com/Uwe/Forums.aspx/jeep-cars/200508/1
#25
Guest
Posts: n/a
Re: YJ slave cylinder
also, speaking with Carl, he ordered a new throwout bearing, but they sent
him the wrong one, not the slave/bearing showed in your photo. Sooooooo
he was forced to use the old one.........
L.W.(ßill) ------ III wrote:
>Hi Carl,
> As Earle suggested the other day you need the newer bellhousing to
>fit your AX5 to make the conversion to an external slave. You may see
>why yours failed as the loose straps in the picture hold the slave
>collapsed until it's held by it's limitations inside the housing. I
>would say it would be smart to start with a new slave each time it comes
>apart: http://www.----------.com/YJslave.jpg
> God Bless America, ßill O|||||||O
>mailto:--------------------
>
>> Well, the slave cylinder died on my YJ today. Will the slave out of an AX15
>> fit my AX5?
>>
>> Carl
--
Message posted via CarKB.com
http://www.carkb.com/Uwe/Forums.aspx/jeep-cars/200508/1
him the wrong one, not the slave/bearing showed in your photo. Sooooooo
he was forced to use the old one.........
L.W.(ßill) ------ III wrote:
>Hi Carl,
> As Earle suggested the other day you need the newer bellhousing to
>fit your AX5 to make the conversion to an external slave. You may see
>why yours failed as the loose straps in the picture hold the slave
>collapsed until it's held by it's limitations inside the housing. I
>would say it would be smart to start with a new slave each time it comes
>apart: http://www.----------.com/YJslave.jpg
> God Bless America, ßill O|||||||O
>mailto:--------------------
>
>> Well, the slave cylinder died on my YJ today. Will the slave out of an AX15
>> fit my AX5?
>>
>> Carl
--
Message posted via CarKB.com
http://www.carkb.com/Uwe/Forums.aspx/jeep-cars/200508/1
#26
Guest
Posts: n/a
Re: YJ slave cylinder
Ah, it was my fault. I knew I should have replaced it. Actually the fluid
was on the bottom of the transmission, I must have not been clear. Going to
drive it to work today and see how it goes.
Carl
"Robb S via CarKB.com" <forum@CarKB.com> wrote in message
news:5291D911537DA@CarKB.com...
> I suggested that to Carl Bill, but cost and timing restraints were
liminting
> his resourses at the time. I spoke with Carl on the phone, apparently
there
> is fluid on top of his transmission, according to him. I suggested to him
> that it might be a possibility that the bleeder was a little loose.......
> (hoping). Not sure where the bleeder is on the 4 banger. he says after
the
> failure, he refilled and can't find any leakage after someone pumped it
150
> times......
> Sooooooo
> I suggested to him to refill it, and keep some fluid with him and check it
> often until the problem area either showes itself or he replaces the
slave....
> .....
>
> L.W.(ßill) ------ III wrote:
> >Hi Carl,
> > As Earle suggested the other day you need the newer bellhousing to
> >fit your AX5 to make the conversion to an external slave. You may see
> >why yours failed as the loose straps in the picture hold the slave
> >collapsed until it's held by it's limitations inside the housing. I
> >would say it would be smart to start with a new slave each time it comes
> >apart: http://www.----------.com/YJslave.jpg
> > God Bless America, ßill O|||||||O
> >mailto:--------------------
> >
> >> Well, the slave cylinder died on my YJ today. Will the slave out of an
AX15
> >> fit my AX5?
> >>
> >> Carl
>
>
> --
> Message posted via CarKB.com
> http://www.carkb.com/Uwe/Forums.aspx/jeep-cars/200508/1
was on the bottom of the transmission, I must have not been clear. Going to
drive it to work today and see how it goes.
Carl
"Robb S via CarKB.com" <forum@CarKB.com> wrote in message
news:5291D911537DA@CarKB.com...
> I suggested that to Carl Bill, but cost and timing restraints were
liminting
> his resourses at the time. I spoke with Carl on the phone, apparently
there
> is fluid on top of his transmission, according to him. I suggested to him
> that it might be a possibility that the bleeder was a little loose.......
> (hoping). Not sure where the bleeder is on the 4 banger. he says after
the
> failure, he refilled and can't find any leakage after someone pumped it
150
> times......
> Sooooooo
> I suggested to him to refill it, and keep some fluid with him and check it
> often until the problem area either showes itself or he replaces the
slave....
> .....
>
> L.W.(ßill) ------ III wrote:
> >Hi Carl,
> > As Earle suggested the other day you need the newer bellhousing to
> >fit your AX5 to make the conversion to an external slave. You may see
> >why yours failed as the loose straps in the picture hold the slave
> >collapsed until it's held by it's limitations inside the housing. I
> >would say it would be smart to start with a new slave each time it comes
> >apart: http://www.----------.com/YJslave.jpg
> > God Bless America, ßill O|||||||O
> >mailto:--------------------
> >
> >> Well, the slave cylinder died on my YJ today. Will the slave out of an
AX15
> >> fit my AX5?
> >>
> >> Carl
>
>
> --
> Message posted via CarKB.com
> http://www.carkb.com/Uwe/Forums.aspx/jeep-cars/200508/1
#27
Guest
Posts: n/a
Re: YJ slave cylinder
Ah, it was my fault. I knew I should have replaced it. Actually the fluid
was on the bottom of the transmission, I must have not been clear. Going to
drive it to work today and see how it goes.
Carl
"Robb S via CarKB.com" <forum@CarKB.com> wrote in message
news:5291D911537DA@CarKB.com...
> I suggested that to Carl Bill, but cost and timing restraints were
liminting
> his resourses at the time. I spoke with Carl on the phone, apparently
there
> is fluid on top of his transmission, according to him. I suggested to him
> that it might be a possibility that the bleeder was a little loose.......
> (hoping). Not sure where the bleeder is on the 4 banger. he says after
the
> failure, he refilled and can't find any leakage after someone pumped it
150
> times......
> Sooooooo
> I suggested to him to refill it, and keep some fluid with him and check it
> often until the problem area either showes itself or he replaces the
slave....
> .....
>
> L.W.(ßill) ------ III wrote:
> >Hi Carl,
> > As Earle suggested the other day you need the newer bellhousing to
> >fit your AX5 to make the conversion to an external slave. You may see
> >why yours failed as the loose straps in the picture hold the slave
> >collapsed until it's held by it's limitations inside the housing. I
> >would say it would be smart to start with a new slave each time it comes
> >apart: http://www.----------.com/YJslave.jpg
> > God Bless America, ßill O|||||||O
> >mailto:--------------------
> >
> >> Well, the slave cylinder died on my YJ today. Will the slave out of an
AX15
> >> fit my AX5?
> >>
> >> Carl
>
>
> --
> Message posted via CarKB.com
> http://www.carkb.com/Uwe/Forums.aspx/jeep-cars/200508/1
was on the bottom of the transmission, I must have not been clear. Going to
drive it to work today and see how it goes.
Carl
"Robb S via CarKB.com" <forum@CarKB.com> wrote in message
news:5291D911537DA@CarKB.com...
> I suggested that to Carl Bill, but cost and timing restraints were
liminting
> his resourses at the time. I spoke with Carl on the phone, apparently
there
> is fluid on top of his transmission, according to him. I suggested to him
> that it might be a possibility that the bleeder was a little loose.......
> (hoping). Not sure where the bleeder is on the 4 banger. he says after
the
> failure, he refilled and can't find any leakage after someone pumped it
150
> times......
> Sooooooo
> I suggested to him to refill it, and keep some fluid with him and check it
> often until the problem area either showes itself or he replaces the
slave....
> .....
>
> L.W.(ßill) ------ III wrote:
> >Hi Carl,
> > As Earle suggested the other day you need the newer bellhousing to
> >fit your AX5 to make the conversion to an external slave. You may see
> >why yours failed as the loose straps in the picture hold the slave
> >collapsed until it's held by it's limitations inside the housing. I
> >would say it would be smart to start with a new slave each time it comes
> >apart: http://www.----------.com/YJslave.jpg
> > God Bless America, ßill O|||||||O
> >mailto:--------------------
> >
> >> Well, the slave cylinder died on my YJ today. Will the slave out of an
AX15
> >> fit my AX5?
> >>
> >> Carl
>
>
> --
> Message posted via CarKB.com
> http://www.carkb.com/Uwe/Forums.aspx/jeep-cars/200508/1
#28
Guest
Posts: n/a
Re: YJ slave cylinder
Ah, it was my fault. I knew I should have replaced it. Actually the fluid
was on the bottom of the transmission, I must have not been clear. Going to
drive it to work today and see how it goes.
Carl
"Robb S via CarKB.com" <forum@CarKB.com> wrote in message
news:5291D911537DA@CarKB.com...
> I suggested that to Carl Bill, but cost and timing restraints were
liminting
> his resourses at the time. I spoke with Carl on the phone, apparently
there
> is fluid on top of his transmission, according to him. I suggested to him
> that it might be a possibility that the bleeder was a little loose.......
> (hoping). Not sure where the bleeder is on the 4 banger. he says after
the
> failure, he refilled and can't find any leakage after someone pumped it
150
> times......
> Sooooooo
> I suggested to him to refill it, and keep some fluid with him and check it
> often until the problem area either showes itself or he replaces the
slave....
> .....
>
> L.W.(ßill) ------ III wrote:
> >Hi Carl,
> > As Earle suggested the other day you need the newer bellhousing to
> >fit your AX5 to make the conversion to an external slave. You may see
> >why yours failed as the loose straps in the picture hold the slave
> >collapsed until it's held by it's limitations inside the housing. I
> >would say it would be smart to start with a new slave each time it comes
> >apart: http://www.----------.com/YJslave.jpg
> > God Bless America, ßill O|||||||O
> >mailto:--------------------
> >
> >> Well, the slave cylinder died on my YJ today. Will the slave out of an
AX15
> >> fit my AX5?
> >>
> >> Carl
>
>
> --
> Message posted via CarKB.com
> http://www.carkb.com/Uwe/Forums.aspx/jeep-cars/200508/1
was on the bottom of the transmission, I must have not been clear. Going to
drive it to work today and see how it goes.
Carl
"Robb S via CarKB.com" <forum@CarKB.com> wrote in message
news:5291D911537DA@CarKB.com...
> I suggested that to Carl Bill, but cost and timing restraints were
liminting
> his resourses at the time. I spoke with Carl on the phone, apparently
there
> is fluid on top of his transmission, according to him. I suggested to him
> that it might be a possibility that the bleeder was a little loose.......
> (hoping). Not sure where the bleeder is on the 4 banger. he says after
the
> failure, he refilled and can't find any leakage after someone pumped it
150
> times......
> Sooooooo
> I suggested to him to refill it, and keep some fluid with him and check it
> often until the problem area either showes itself or he replaces the
slave....
> .....
>
> L.W.(ßill) ------ III wrote:
> >Hi Carl,
> > As Earle suggested the other day you need the newer bellhousing to
> >fit your AX5 to make the conversion to an external slave. You may see
> >why yours failed as the loose straps in the picture hold the slave
> >collapsed until it's held by it's limitations inside the housing. I
> >would say it would be smart to start with a new slave each time it comes
> >apart: http://www.----------.com/YJslave.jpg
> > God Bless America, ßill O|||||||O
> >mailto:--------------------
> >
> >> Well, the slave cylinder died on my YJ today. Will the slave out of an
AX15
> >> fit my AX5?
> >>
> >> Carl
>
>
> --
> Message posted via CarKB.com
> http://www.carkb.com/Uwe/Forums.aspx/jeep-cars/200508/1
#29
Guest
Posts: n/a
Re: YJ slave cylinder
Ah, it was my fault. I knew I should have replaced it. Actually the fluid
was on the bottom of the transmission, I must have not been clear. Going to
drive it to work today and see how it goes.
Carl
"Robb S via CarKB.com" <forum@CarKB.com> wrote in message
news:5291D911537DA@CarKB.com...
> I suggested that to Carl Bill, but cost and timing restraints were
liminting
> his resourses at the time. I spoke with Carl on the phone, apparently
there
> is fluid on top of his transmission, according to him. I suggested to him
> that it might be a possibility that the bleeder was a little loose.......
> (hoping). Not sure where the bleeder is on the 4 banger. he says after
the
> failure, he refilled and can't find any leakage after someone pumped it
150
> times......
> Sooooooo
> I suggested to him to refill it, and keep some fluid with him and check it
> often until the problem area either showes itself or he replaces the
slave....
> .....
>
> L.W.(ßill) ------ III wrote:
> >Hi Carl,
> > As Earle suggested the other day you need the newer bellhousing to
> >fit your AX5 to make the conversion to an external slave. You may see
> >why yours failed as the loose straps in the picture hold the slave
> >collapsed until it's held by it's limitations inside the housing. I
> >would say it would be smart to start with a new slave each time it comes
> >apart: http://www.----------.com/YJslave.jpg
> > God Bless America, ßill O|||||||O
> >mailto:--------------------
> >
> >> Well, the slave cylinder died on my YJ today. Will the slave out of an
AX15
> >> fit my AX5?
> >>
> >> Carl
>
>
> --
> Message posted via CarKB.com
> http://www.carkb.com/Uwe/Forums.aspx/jeep-cars/200508/1
was on the bottom of the transmission, I must have not been clear. Going to
drive it to work today and see how it goes.
Carl
"Robb S via CarKB.com" <forum@CarKB.com> wrote in message
news:5291D911537DA@CarKB.com...
> I suggested that to Carl Bill, but cost and timing restraints were
liminting
> his resourses at the time. I spoke with Carl on the phone, apparently
there
> is fluid on top of his transmission, according to him. I suggested to him
> that it might be a possibility that the bleeder was a little loose.......
> (hoping). Not sure where the bleeder is on the 4 banger. he says after
the
> failure, he refilled and can't find any leakage after someone pumped it
150
> times......
> Sooooooo
> I suggested to him to refill it, and keep some fluid with him and check it
> often until the problem area either showes itself or he replaces the
slave....
> .....
>
> L.W.(ßill) ------ III wrote:
> >Hi Carl,
> > As Earle suggested the other day you need the newer bellhousing to
> >fit your AX5 to make the conversion to an external slave. You may see
> >why yours failed as the loose straps in the picture hold the slave
> >collapsed until it's held by it's limitations inside the housing. I
> >would say it would be smart to start with a new slave each time it comes
> >apart: http://www.----------.com/YJslave.jpg
> > God Bless America, ßill O|||||||O
> >mailto:--------------------
> >
> >> Well, the slave cylinder died on my YJ today. Will the slave out of an
AX15
> >> fit my AX5?
> >>
> >> Carl
>
>
> --
> Message posted via CarKB.com
> http://www.carkb.com/Uwe/Forums.aspx/jeep-cars/200508/1
#30
Guest
Posts: n/a
Re: YJ slave cylinder
so Carl, how's the slave treating you? ;)
Robb S wrote:
>also, speaking with Carl, he ordered a new throwout bearing, but they sent
>him the wrong one, not the slave/bearing showed in your photo. Sooooooo
>he was forced to use the old one.........
>
>>Hi Carl,
>> As Earle suggested the other day you need the newer bellhousing to
>[quoted text clipped - 10 lines]
>>>
>>> Carl
--
Message posted via CarKB.com
http://www.carkb.com/Uwe/Forums.aspx/jeep-cars/200508/1
Robb S wrote:
>also, speaking with Carl, he ordered a new throwout bearing, but they sent
>him the wrong one, not the slave/bearing showed in your photo. Sooooooo
>he was forced to use the old one.........
>
>>Hi Carl,
>> As Earle suggested the other day you need the newer bellhousing to
>[quoted text clipped - 10 lines]
>>>
>>> Carl
--
Message posted via CarKB.com
http://www.carkb.com/Uwe/Forums.aspx/jeep-cars/200508/1