Winch security
#41
Guest
Posts: n/a
Re: Winch security
RoyJ did pass the time by typing:
> The nice way to do it is to weld a 2" long stub piece of 1" (ID) pipe
> over one or more of the bolt holes. Drill a 3/8' cross hole then install
> the winch as normal, using a deep socket to tighten the bolts up.
> Install a 3/8" bolt through the cross hole, weld the nut tight. If you
> want to remove the mounting bolt, hacksaw or torch off the 3/8" cross bolt.
Actually you could do the same thing but instead of a bolt welded through, just
use a padlock.
> The nice way to do it is to weld a 2" long stub piece of 1" (ID) pipe
> over one or more of the bolt holes. Drill a 3/8' cross hole then install
> the winch as normal, using a deep socket to tighten the bolts up.
> Install a 3/8" bolt through the cross hole, weld the nut tight. If you
> want to remove the mounting bolt, hacksaw or torch off the 3/8" cross bolt.
Actually you could do the same thing but instead of a bolt welded through, just
use a padlock.
#42
Guest
Posts: n/a
Re: Winch security
RoyJ did pass the time by typing:
> The nice way to do it is to weld a 2" long stub piece of 1" (ID) pipe
> over one or more of the bolt holes. Drill a 3/8' cross hole then install
> the winch as normal, using a deep socket to tighten the bolts up.
> Install a 3/8" bolt through the cross hole, weld the nut tight. If you
> want to remove the mounting bolt, hacksaw or torch off the 3/8" cross bolt.
Actually you could do the same thing but instead of a bolt welded through, just
use a padlock.
> The nice way to do it is to weld a 2" long stub piece of 1" (ID) pipe
> over one or more of the bolt holes. Drill a 3/8' cross hole then install
> the winch as normal, using a deep socket to tighten the bolts up.
> Install a 3/8" bolt through the cross hole, weld the nut tight. If you
> want to remove the mounting bolt, hacksaw or torch off the 3/8" cross bolt.
Actually you could do the same thing but instead of a bolt welded through, just
use a padlock.
#43
Guest
Posts: n/a
Re: Winch security
RoyJ did pass the time by typing:
> The nice way to do it is to weld a 2" long stub piece of 1" (ID) pipe
> over one or more of the bolt holes. Drill a 3/8' cross hole then install
> the winch as normal, using a deep socket to tighten the bolts up.
> Install a 3/8" bolt through the cross hole, weld the nut tight. If you
> want to remove the mounting bolt, hacksaw or torch off the 3/8" cross bolt.
Actually you could do the same thing but instead of a bolt welded through, just
use a padlock.
> The nice way to do it is to weld a 2" long stub piece of 1" (ID) pipe
> over one or more of the bolt holes. Drill a 3/8' cross hole then install
> the winch as normal, using a deep socket to tighten the bolts up.
> Install a 3/8" bolt through the cross hole, weld the nut tight. If you
> want to remove the mounting bolt, hacksaw or torch off the 3/8" cross bolt.
Actually you could do the same thing but instead of a bolt welded through, just
use a padlock.
#44
Guest
Posts: n/a
Re: Winch security
That's used on all Kalifornia State Park gates here, I think they
modified their combination locks to fit inside a pipe after a friend
shot it off with his 357. We were caught and had to go to court, but
paid off a judge and it was dismissed and didn't have to appear.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
DougW wrote:
>
>
> Actually you could do the same thing but instead of a bolt welded through, just
> use a padlock.
modified their combination locks to fit inside a pipe after a friend
shot it off with his 357. We were caught and had to go to court, but
paid off a judge and it was dismissed and didn't have to appear.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
DougW wrote:
>
>
> Actually you could do the same thing but instead of a bolt welded through, just
> use a padlock.
#45
Guest
Posts: n/a
Re: Winch security
That's used on all Kalifornia State Park gates here, I think they
modified their combination locks to fit inside a pipe after a friend
shot it off with his 357. We were caught and had to go to court, but
paid off a judge and it was dismissed and didn't have to appear.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
DougW wrote:
>
>
> Actually you could do the same thing but instead of a bolt welded through, just
> use a padlock.
modified their combination locks to fit inside a pipe after a friend
shot it off with his 357. We were caught and had to go to court, but
paid off a judge and it was dismissed and didn't have to appear.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
DougW wrote:
>
>
> Actually you could do the same thing but instead of a bolt welded through, just
> use a padlock.
#46
Guest
Posts: n/a
Re: Winch security
That's used on all Kalifornia State Park gates here, I think they
modified their combination locks to fit inside a pipe after a friend
shot it off with his 357. We were caught and had to go to court, but
paid off a judge and it was dismissed and didn't have to appear.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
DougW wrote:
>
>
> Actually you could do the same thing but instead of a bolt welded through, just
> use a padlock.
modified their combination locks to fit inside a pipe after a friend
shot it off with his 357. We were caught and had to go to court, but
paid off a judge and it was dismissed and didn't have to appear.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
DougW wrote:
>
>
> Actually you could do the same thing but instead of a bolt welded through, just
> use a padlock.
#47
Guest
Posts: n/a
Re: Winch security
This type normally used a padlock, they get rusty. It's easier, cheaper,
to use the bolt.
DougW wrote:
> RoyJ did pass the time by typing:
>
>>The nice way to do it is to weld a 2" long stub piece of 1" (ID) pipe
>>over one or more of the bolt holes. Drill a 3/8' cross hole then install
>>the winch as normal, using a deep socket to tighten the bolts up.
>>Install a 3/8" bolt through the cross hole, weld the nut tight. If you
>>want to remove the mounting bolt, hacksaw or torch off the 3/8" cross bolt.
>
>
> Actually you could do the same thing but instead of a bolt welded through, just
> use a padlock.
>
>
to use the bolt.
DougW wrote:
> RoyJ did pass the time by typing:
>
>>The nice way to do it is to weld a 2" long stub piece of 1" (ID) pipe
>>over one or more of the bolt holes. Drill a 3/8' cross hole then install
>>the winch as normal, using a deep socket to tighten the bolts up.
>>Install a 3/8" bolt through the cross hole, weld the nut tight. If you
>>want to remove the mounting bolt, hacksaw or torch off the 3/8" cross bolt.
>
>
> Actually you could do the same thing but instead of a bolt welded through, just
> use a padlock.
>
>
#48
Guest
Posts: n/a
Re: Winch security
This type normally used a padlock, they get rusty. It's easier, cheaper,
to use the bolt.
DougW wrote:
> RoyJ did pass the time by typing:
>
>>The nice way to do it is to weld a 2" long stub piece of 1" (ID) pipe
>>over one or more of the bolt holes. Drill a 3/8' cross hole then install
>>the winch as normal, using a deep socket to tighten the bolts up.
>>Install a 3/8" bolt through the cross hole, weld the nut tight. If you
>>want to remove the mounting bolt, hacksaw or torch off the 3/8" cross bolt.
>
>
> Actually you could do the same thing but instead of a bolt welded through, just
> use a padlock.
>
>
to use the bolt.
DougW wrote:
> RoyJ did pass the time by typing:
>
>>The nice way to do it is to weld a 2" long stub piece of 1" (ID) pipe
>>over one or more of the bolt holes. Drill a 3/8' cross hole then install
>>the winch as normal, using a deep socket to tighten the bolts up.
>>Install a 3/8" bolt through the cross hole, weld the nut tight. If you
>>want to remove the mounting bolt, hacksaw or torch off the 3/8" cross bolt.
>
>
> Actually you could do the same thing but instead of a bolt welded through, just
> use a padlock.
>
>
#49
Guest
Posts: n/a
Re: Winch security
This type normally used a padlock, they get rusty. It's easier, cheaper,
to use the bolt.
DougW wrote:
> RoyJ did pass the time by typing:
>
>>The nice way to do it is to weld a 2" long stub piece of 1" (ID) pipe
>>over one or more of the bolt holes. Drill a 3/8' cross hole then install
>>the winch as normal, using a deep socket to tighten the bolts up.
>>Install a 3/8" bolt through the cross hole, weld the nut tight. If you
>>want to remove the mounting bolt, hacksaw or torch off the 3/8" cross bolt.
>
>
> Actually you could do the same thing but instead of a bolt welded through, just
> use a padlock.
>
>
to use the bolt.
DougW wrote:
> RoyJ did pass the time by typing:
>
>>The nice way to do it is to weld a 2" long stub piece of 1" (ID) pipe
>>over one or more of the bolt holes. Drill a 3/8' cross hole then install
>>the winch as normal, using a deep socket to tighten the bolts up.
>>Install a 3/8" bolt through the cross hole, weld the nut tight. If you
>>want to remove the mounting bolt, hacksaw or torch off the 3/8" cross bolt.
>
>
> Actually you could do the same thing but instead of a bolt welded through, just
> use a padlock.
>
>
#50
Guest
Posts: n/a
Re: Winch security
The 357 seems to be a combination that works on nearly any lock
"L.W. ("ßill") ------ III" <----------@***.net> wrote in message
news:41F2A3C1.A17FBA29@***.net...
> That's used on all Kalifornia State Park gates here, I think they
> modified their combination locks to fit inside a pipe after a friend
> shot it off with his 357. We were caught and had to go to court, but
> paid off a judge and it was dismissed and didn't have to appear.
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
> DougW wrote:
>>
>>
>> Actually you could do the same thing but instead of a bolt welded
>> through, just
>> use a padlock.
"L.W. ("ßill") ------ III" <----------@***.net> wrote in message
news:41F2A3C1.A17FBA29@***.net...
> That's used on all Kalifornia State Park gates here, I think they
> modified their combination locks to fit inside a pipe after a friend
> shot it off with his 357. We were caught and had to go to court, but
> paid off a judge and it was dismissed and didn't have to appear.
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
> DougW wrote:
>>
>>
>> Actually you could do the same thing but instead of a bolt welded
>> through, just
>> use a padlock.