Trac - Loc
Guest
Posts: n/a
Re: Trac - Loc
Jerry-
What engine?
Carl
"Jerry Bransford" <jerrypb@***.net> wrote in message
news:bDn2f.2457$MN6.573@fed1read04...
> My thankfully long-gone D35c axle grenaded/self-destructed 6 weeks after
> installing a locker. The axle had 33" tires on it during a slow-speed
> u-turn at a light-controlled intersection when it grenaded loudly enough
> to cause people a block away to look up to see what happened. I strongly
> recommend you not install a locker into a D35c, no matter how carefully
> you drive it. The trouble it causes is just not worth it.
>
> Jerry
>
> Carl wrote:
>> Ya, I realize the risk. A lot of my friends run locked up D35's on large
>> and larger tires. General rule of thumb: Drive it like its a D35. Even
>> with the low-output 4cyl, I'm sure it will eventually break.
>>
>> Thanks for the input guys.. looks like I'll be going with a brand new
>> lockright.
>>
>> Carl
>>
>>
>> "Jerry Bransford" <jerrypb@***.net> wrote in message
>> news:Xrn2f.2455$MN6.950@fed1read04...
>>
>>>Yep but the axleshafts on your Dana 35c sure are not even close to being
>>>strong enough to run a locker and 33" tires.
>>>
>>>Jerry
>>>
>>>Carl wrote:
>>>
>>>>Is a lockright strong enough for my 4cyl turning 33's?
>>>>
>>>>Carl
>>>>
>>>>"L.W. ("ßill") ------ III" <----------@***.net> wrote in message
>>>>news:4349FC78.1EA322B2@***.net...
>>>>
>>>>
>>>>>Hi Carl,
>>>>> The Lock Right locker from Powertrax will slip right in place of
>>>>>your spiders, but it's not very strong. The Detroit will take a bunch
>>>>>of
>>>>>precise tools and a junk drawer full of shims to bring her in, may be
>>>>>better to let a professional take responsibility for it:
>>>>>http://www.differentials.com/install.html
>>>>>http://www.----------.com/dana35c/TJDana35.pdf
>>>>> God Bless America, Bill O|||||||O
>>>>>mailto:-------------------- http://www.----------.com/
>>>>>
>>>>>Carl wrote:
>>>>>
>>>>>
>>>>>>The one I'm looking at is in an apparently good rear end with 4.10
>>>>>>gears.
>>>>>>It's located far away so I told him I just want the locker. You're
>>>>>>probably
>>>>>>right -you usually are- .. I think I'll just shell out the $$ for a
>>>>>>new one.
>>>>>>
>>>>>>Is a locker difficult to install?
>>>>>>
>>>>>>Carl
>>>>
>>>>
>>>>
>>>--
>>>Jerry Bransford
>>>PP-ASEL N6TAY
>>>See the Geezer Jeep at
>>>http://members.***.net/jerrypb/
>>
>>
>>
>
> --
> Jerry Bransford
> PP-ASEL N6TAY
> See the Geezer Jeep at
> http://members.***.net/jerrypb/
What engine?
Carl
"Jerry Bransford" <jerrypb@***.net> wrote in message
news:bDn2f.2457$MN6.573@fed1read04...
> My thankfully long-gone D35c axle grenaded/self-destructed 6 weeks after
> installing a locker. The axle had 33" tires on it during a slow-speed
> u-turn at a light-controlled intersection when it grenaded loudly enough
> to cause people a block away to look up to see what happened. I strongly
> recommend you not install a locker into a D35c, no matter how carefully
> you drive it. The trouble it causes is just not worth it.
>
> Jerry
>
> Carl wrote:
>> Ya, I realize the risk. A lot of my friends run locked up D35's on large
>> and larger tires. General rule of thumb: Drive it like its a D35. Even
>> with the low-output 4cyl, I'm sure it will eventually break.
>>
>> Thanks for the input guys.. looks like I'll be going with a brand new
>> lockright.
>>
>> Carl
>>
>>
>> "Jerry Bransford" <jerrypb@***.net> wrote in message
>> news:Xrn2f.2455$MN6.950@fed1read04...
>>
>>>Yep but the axleshafts on your Dana 35c sure are not even close to being
>>>strong enough to run a locker and 33" tires.
>>>
>>>Jerry
>>>
>>>Carl wrote:
>>>
>>>>Is a lockright strong enough for my 4cyl turning 33's?
>>>>
>>>>Carl
>>>>
>>>>"L.W. ("ßill") ------ III" <----------@***.net> wrote in message
>>>>news:4349FC78.1EA322B2@***.net...
>>>>
>>>>
>>>>>Hi Carl,
>>>>> The Lock Right locker from Powertrax will slip right in place of
>>>>>your spiders, but it's not very strong. The Detroit will take a bunch
>>>>>of
>>>>>precise tools and a junk drawer full of shims to bring her in, may be
>>>>>better to let a professional take responsibility for it:
>>>>>http://www.differentials.com/install.html
>>>>>http://www.----------.com/dana35c/TJDana35.pdf
>>>>> God Bless America, Bill O|||||||O
>>>>>mailto:-------------------- http://www.----------.com/
>>>>>
>>>>>Carl wrote:
>>>>>
>>>>>
>>>>>>The one I'm looking at is in an apparently good rear end with 4.10
>>>>>>gears.
>>>>>>It's located far away so I told him I just want the locker. You're
>>>>>>probably
>>>>>>right -you usually are- .. I think I'll just shell out the $$ for a
>>>>>>new one.
>>>>>>
>>>>>>Is a locker difficult to install?
>>>>>>
>>>>>>Carl
>>>>
>>>>
>>>>
>>>--
>>>Jerry Bransford
>>>PP-ASEL N6TAY
>>>See the Geezer Jeep at
>>>http://members.***.net/jerrypb/
>>
>>
>>
>
> --
> Jerry Bransford
> PP-ASEL N6TAY
> See the Geezer Jeep at
> http://members.***.net/jerrypb/
Guest
Posts: n/a
Re: Trac - Loc
Jerry-
What engine?
Carl
"Jerry Bransford" <jerrypb@***.net> wrote in message
news:bDn2f.2457$MN6.573@fed1read04...
> My thankfully long-gone D35c axle grenaded/self-destructed 6 weeks after
> installing a locker. The axle had 33" tires on it during a slow-speed
> u-turn at a light-controlled intersection when it grenaded loudly enough
> to cause people a block away to look up to see what happened. I strongly
> recommend you not install a locker into a D35c, no matter how carefully
> you drive it. The trouble it causes is just not worth it.
>
> Jerry
>
> Carl wrote:
>> Ya, I realize the risk. A lot of my friends run locked up D35's on large
>> and larger tires. General rule of thumb: Drive it like its a D35. Even
>> with the low-output 4cyl, I'm sure it will eventually break.
>>
>> Thanks for the input guys.. looks like I'll be going with a brand new
>> lockright.
>>
>> Carl
>>
>>
>> "Jerry Bransford" <jerrypb@***.net> wrote in message
>> news:Xrn2f.2455$MN6.950@fed1read04...
>>
>>>Yep but the axleshafts on your Dana 35c sure are not even close to being
>>>strong enough to run a locker and 33" tires.
>>>
>>>Jerry
>>>
>>>Carl wrote:
>>>
>>>>Is a lockright strong enough for my 4cyl turning 33's?
>>>>
>>>>Carl
>>>>
>>>>"L.W. ("ßill") ------ III" <----------@***.net> wrote in message
>>>>news:4349FC78.1EA322B2@***.net...
>>>>
>>>>
>>>>>Hi Carl,
>>>>> The Lock Right locker from Powertrax will slip right in place of
>>>>>your spiders, but it's not very strong. The Detroit will take a bunch
>>>>>of
>>>>>precise tools and a junk drawer full of shims to bring her in, may be
>>>>>better to let a professional take responsibility for it:
>>>>>http://www.differentials.com/install.html
>>>>>http://www.----------.com/dana35c/TJDana35.pdf
>>>>> God Bless America, Bill O|||||||O
>>>>>mailto:-------------------- http://www.----------.com/
>>>>>
>>>>>Carl wrote:
>>>>>
>>>>>
>>>>>>The one I'm looking at is in an apparently good rear end with 4.10
>>>>>>gears.
>>>>>>It's located far away so I told him I just want the locker. You're
>>>>>>probably
>>>>>>right -you usually are- .. I think I'll just shell out the $$ for a
>>>>>>new one.
>>>>>>
>>>>>>Is a locker difficult to install?
>>>>>>
>>>>>>Carl
>>>>
>>>>
>>>>
>>>--
>>>Jerry Bransford
>>>PP-ASEL N6TAY
>>>See the Geezer Jeep at
>>>http://members.***.net/jerrypb/
>>
>>
>>
>
> --
> Jerry Bransford
> PP-ASEL N6TAY
> See the Geezer Jeep at
> http://members.***.net/jerrypb/
What engine?
Carl
"Jerry Bransford" <jerrypb@***.net> wrote in message
news:bDn2f.2457$MN6.573@fed1read04...
> My thankfully long-gone D35c axle grenaded/self-destructed 6 weeks after
> installing a locker. The axle had 33" tires on it during a slow-speed
> u-turn at a light-controlled intersection when it grenaded loudly enough
> to cause people a block away to look up to see what happened. I strongly
> recommend you not install a locker into a D35c, no matter how carefully
> you drive it. The trouble it causes is just not worth it.
>
> Jerry
>
> Carl wrote:
>> Ya, I realize the risk. A lot of my friends run locked up D35's on large
>> and larger tires. General rule of thumb: Drive it like its a D35. Even
>> with the low-output 4cyl, I'm sure it will eventually break.
>>
>> Thanks for the input guys.. looks like I'll be going with a brand new
>> lockright.
>>
>> Carl
>>
>>
>> "Jerry Bransford" <jerrypb@***.net> wrote in message
>> news:Xrn2f.2455$MN6.950@fed1read04...
>>
>>>Yep but the axleshafts on your Dana 35c sure are not even close to being
>>>strong enough to run a locker and 33" tires.
>>>
>>>Jerry
>>>
>>>Carl wrote:
>>>
>>>>Is a lockright strong enough for my 4cyl turning 33's?
>>>>
>>>>Carl
>>>>
>>>>"L.W. ("ßill") ------ III" <----------@***.net> wrote in message
>>>>news:4349FC78.1EA322B2@***.net...
>>>>
>>>>
>>>>>Hi Carl,
>>>>> The Lock Right locker from Powertrax will slip right in place of
>>>>>your spiders, but it's not very strong. The Detroit will take a bunch
>>>>>of
>>>>>precise tools and a junk drawer full of shims to bring her in, may be
>>>>>better to let a professional take responsibility for it:
>>>>>http://www.differentials.com/install.html
>>>>>http://www.----------.com/dana35c/TJDana35.pdf
>>>>> God Bless America, Bill O|||||||O
>>>>>mailto:-------------------- http://www.----------.com/
>>>>>
>>>>>Carl wrote:
>>>>>
>>>>>
>>>>>>The one I'm looking at is in an apparently good rear end with 4.10
>>>>>>gears.
>>>>>>It's located far away so I told him I just want the locker. You're
>>>>>>probably
>>>>>>right -you usually are- .. I think I'll just shell out the $$ for a
>>>>>>new one.
>>>>>>
>>>>>>Is a locker difficult to install?
>>>>>>
>>>>>>Carl
>>>>
>>>>
>>>>
>>>--
>>>Jerry Bransford
>>>PP-ASEL N6TAY
>>>See the Geezer Jeep at
>>>http://members.***.net/jerrypb/
>>
>>
>>
>
> --
> Jerry Bransford
> PP-ASEL N6TAY
> See the Geezer Jeep at
> http://members.***.net/jerrypb/
Guest
Posts: n/a
Re: Trac - Loc
Like bill said, that looks like an open carrier taken out after putting a
detroit in, go have a look here for your prices and pictures
http://completeoffroad.com/wsm/c-15_dana__35_m35.html unfortunately they
don't have a pic of the dana 35 detroit, but you could look at the D 44, D
30, 9" ones etc. Good place to buy from, best I found on the net for prices,
I am in Canada and saved $200.00 on my daughter's 9" detroit and $250.00 on
my AMC 20 detroit.
Greg
"Carl" <carlsaiyed@REMOVE.hotmail.com> wrote in message
news:MN2dnfQtbKP9n9feRVn-uA@comcast.com...
> Wow, so he is ripping someone off?
>
> Carl
>
> "L.W. ("ßill") ------ III" <----------@***.net> wrote in message
> news:434A00A2.C6148F25@***.net...
>> Hi Carl,
>> That's what I hate about EBay! What you're looking at is the Locker
>> box and the old stock open differential. The Detroit will look machined
>> like the one at: http://www.4x4wire.com/jeep/reviews/super35d/
>> God Bless America, Bill O|||||||O
>> mailto:-------------------- http://www.----------.com/
>>
>> Carl wrote:
>>>
>>> Bill-
>>> What about this one?
>>> http://cgi.ebay.com/ebaymotors/ws/eB...tem=8004904578
>>>
>>> Carl
>
>
detroit in, go have a look here for your prices and pictures
http://completeoffroad.com/wsm/c-15_dana__35_m35.html unfortunately they
don't have a pic of the dana 35 detroit, but you could look at the D 44, D
30, 9" ones etc. Good place to buy from, best I found on the net for prices,
I am in Canada and saved $200.00 on my daughter's 9" detroit and $250.00 on
my AMC 20 detroit.
Greg
"Carl" <carlsaiyed@REMOVE.hotmail.com> wrote in message
news:MN2dnfQtbKP9n9feRVn-uA@comcast.com...
> Wow, so he is ripping someone off?
>
> Carl
>
> "L.W. ("ßill") ------ III" <----------@***.net> wrote in message
> news:434A00A2.C6148F25@***.net...
>> Hi Carl,
>> That's what I hate about EBay! What you're looking at is the Locker
>> box and the old stock open differential. The Detroit will look machined
>> like the one at: http://www.4x4wire.com/jeep/reviews/super35d/
>> God Bless America, Bill O|||||||O
>> mailto:-------------------- http://www.----------.com/
>>
>> Carl wrote:
>>>
>>> Bill-
>>> What about this one?
>>> http://cgi.ebay.com/ebaymotors/ws/eB...tem=8004904578
>>>
>>> Carl
>
>
Guest
Posts: n/a
Re: Trac - Loc
Like bill said, that looks like an open carrier taken out after putting a
detroit in, go have a look here for your prices and pictures
http://completeoffroad.com/wsm/c-15_dana__35_m35.html unfortunately they
don't have a pic of the dana 35 detroit, but you could look at the D 44, D
30, 9" ones etc. Good place to buy from, best I found on the net for prices,
I am in Canada and saved $200.00 on my daughter's 9" detroit and $250.00 on
my AMC 20 detroit.
Greg
"Carl" <carlsaiyed@REMOVE.hotmail.com> wrote in message
news:MN2dnfQtbKP9n9feRVn-uA@comcast.com...
> Wow, so he is ripping someone off?
>
> Carl
>
> "L.W. ("ßill") ------ III" <----------@***.net> wrote in message
> news:434A00A2.C6148F25@***.net...
>> Hi Carl,
>> That's what I hate about EBay! What you're looking at is the Locker
>> box and the old stock open differential. The Detroit will look machined
>> like the one at: http://www.4x4wire.com/jeep/reviews/super35d/
>> God Bless America, Bill O|||||||O
>> mailto:-------------------- http://www.----------.com/
>>
>> Carl wrote:
>>>
>>> Bill-
>>> What about this one?
>>> http://cgi.ebay.com/ebaymotors/ws/eB...tem=8004904578
>>>
>>> Carl
>
>
detroit in, go have a look here for your prices and pictures
http://completeoffroad.com/wsm/c-15_dana__35_m35.html unfortunately they
don't have a pic of the dana 35 detroit, but you could look at the D 44, D
30, 9" ones etc. Good place to buy from, best I found on the net for prices,
I am in Canada and saved $200.00 on my daughter's 9" detroit and $250.00 on
my AMC 20 detroit.
Greg
"Carl" <carlsaiyed@REMOVE.hotmail.com> wrote in message
news:MN2dnfQtbKP9n9feRVn-uA@comcast.com...
> Wow, so he is ripping someone off?
>
> Carl
>
> "L.W. ("ßill") ------ III" <----------@***.net> wrote in message
> news:434A00A2.C6148F25@***.net...
>> Hi Carl,
>> That's what I hate about EBay! What you're looking at is the Locker
>> box and the old stock open differential. The Detroit will look machined
>> like the one at: http://www.4x4wire.com/jeep/reviews/super35d/
>> God Bless America, Bill O|||||||O
>> mailto:-------------------- http://www.----------.com/
>>
>> Carl wrote:
>>>
>>> Bill-
>>> What about this one?
>>> http://cgi.ebay.com/ebaymotors/ws/eB...tem=8004904578
>>>
>>> Carl
>
>
Guest
Posts: n/a
Re: Trac - Loc
Like bill said, that looks like an open carrier taken out after putting a
detroit in, go have a look here for your prices and pictures
http://completeoffroad.com/wsm/c-15_dana__35_m35.html unfortunately they
don't have a pic of the dana 35 detroit, but you could look at the D 44, D
30, 9" ones etc. Good place to buy from, best I found on the net for prices,
I am in Canada and saved $200.00 on my daughter's 9" detroit and $250.00 on
my AMC 20 detroit.
Greg
"Carl" <carlsaiyed@REMOVE.hotmail.com> wrote in message
news:MN2dnfQtbKP9n9feRVn-uA@comcast.com...
> Wow, so he is ripping someone off?
>
> Carl
>
> "L.W. ("ßill") ------ III" <----------@***.net> wrote in message
> news:434A00A2.C6148F25@***.net...
>> Hi Carl,
>> That's what I hate about EBay! What you're looking at is the Locker
>> box and the old stock open differential. The Detroit will look machined
>> like the one at: http://www.4x4wire.com/jeep/reviews/super35d/
>> God Bless America, Bill O|||||||O
>> mailto:-------------------- http://www.----------.com/
>>
>> Carl wrote:
>>>
>>> Bill-
>>> What about this one?
>>> http://cgi.ebay.com/ebaymotors/ws/eB...tem=8004904578
>>>
>>> Carl
>
>
detroit in, go have a look here for your prices and pictures
http://completeoffroad.com/wsm/c-15_dana__35_m35.html unfortunately they
don't have a pic of the dana 35 detroit, but you could look at the D 44, D
30, 9" ones etc. Good place to buy from, best I found on the net for prices,
I am in Canada and saved $200.00 on my daughter's 9" detroit and $250.00 on
my AMC 20 detroit.
Greg
"Carl" <carlsaiyed@REMOVE.hotmail.com> wrote in message
news:MN2dnfQtbKP9n9feRVn-uA@comcast.com...
> Wow, so he is ripping someone off?
>
> Carl
>
> "L.W. ("ßill") ------ III" <----------@***.net> wrote in message
> news:434A00A2.C6148F25@***.net...
>> Hi Carl,
>> That's what I hate about EBay! What you're looking at is the Locker
>> box and the old stock open differential. The Detroit will look machined
>> like the one at: http://www.4x4wire.com/jeep/reviews/super35d/
>> God Bless America, Bill O|||||||O
>> mailto:-------------------- http://www.----------.com/
>>
>> Carl wrote:
>>>
>>> Bill-
>>> What about this one?
>>> http://cgi.ebay.com/ebaymotors/ws/eB...tem=8004904578
>>>
>>> Carl
>
>
Guest
Posts: n/a
Re: Trac - Loc
Does it matter? I was doing a u-turn and nearly coasting through it at
minimal power.
Carl wrote:
> Jerry-
> What engine?
>
> Carl
>
> "Jerry Bransford" <jerrypb@***.net> wrote in message
> news:bDn2f.2457$MN6.573@fed1read04...
>
>>My thankfully long-gone D35c axle grenaded/self-destructed 6 weeks after
>>installing a locker. The axle had 33" tires on it during a slow-speed
>>u-turn at a light-controlled intersection when it grenaded loudly enough
>>to cause people a block away to look up to see what happened. I strongly
>>recommend you not install a locker into a D35c, no matter how carefully
>>you drive it. The trouble it causes is just not worth it.
>>
>>Jerry
>>
>>Carl wrote:
>>
>>>Ya, I realize the risk. A lot of my friends run locked up D35's on large
>>>and larger tires. General rule of thumb: Drive it like its a D35. Even
>>>with the low-output 4cyl, I'm sure it will eventually break.
>>>
>>>Thanks for the input guys.. looks like I'll be going with a brand new
>>>lockright.
>>>
>>>Carl
>>>
>>>
>>>"Jerry Bransford" <jerrypb@***.net> wrote in message
>>>news:Xrn2f.2455$MN6.950@fed1read04...
>>>
>>>
>>>>Yep but the axleshafts on your Dana 35c sure are not even close to being
>>>>strong enough to run a locker and 33" tires.
>>>>
>>>>Jerry
>>>>
>>>>Carl wrote:
>>>>
>>>>
>>>>>Is a lockright strong enough for my 4cyl turning 33's?
>>>>>
>>>>>Carl
>>>>>
>>>>>"L.W. ("ßill") ------ III" <----------@***.net> wrote in message
>>>>>news:4349FC78.1EA322B2@***.net...
>>>>>
>>>>>
>>>>>
>>>>>>Hi Carl,
>>>>>> The Lock Right locker from Powertrax will slip right in place of
>>>>>>your spiders, but it's not very strong. The Detroit will take a bunch
>>>>>>of
>>>>>>precise tools and a junk drawer full of shims to bring her in, may be
>>>>>>better to let a professional take responsibility for it:
>>>>>>http://www.differentials.com/install.html
>>>>>>http://www.----------.com/dana35c/TJDana35.pdf
>>>>>> God Bless America, Bill O|||||||O
>>>>>>mailto:-------------------- http://www.----------.com/
>>>>>>
>>>>>>Carl wrote:
>>>>>>
>>>>>>
>>>>>>
>>>>>>>The one I'm looking at is in an apparently good rear end with 4.10
>>>>>>>gears.
>>>>>>>It's located far away so I told him I just want the locker. You're
>>>>>>>probably
>>>>>>>right -you usually are- .. I think I'll just shell out the $$ for a
>>>>>>>new one.
>>>>>>>
>>>>>>>Is a locker difficult to install?
>>>>>>>
>>>>>>>Carl
>>>>>
>>>>>
>>>>>
>>>>--
>>>>Jerry Bransford
>>>>PP-ASEL N6TAY
>>>>See the Geezer Jeep at
>>>>http://members.***.net/jerrypb/
>>>
>>>
>>>
>>--
>>Jerry Bransford
>>PP-ASEL N6TAY
>>See the Geezer Jeep at
>>http://members.***.net/jerrypb/
>
>
>
--
Jerry Bransford
PP-ASEL N6TAY
See the Geezer Jeep at
http://members.***.net/jerrypb/
minimal power.
Carl wrote:
> Jerry-
> What engine?
>
> Carl
>
> "Jerry Bransford" <jerrypb@***.net> wrote in message
> news:bDn2f.2457$MN6.573@fed1read04...
>
>>My thankfully long-gone D35c axle grenaded/self-destructed 6 weeks after
>>installing a locker. The axle had 33" tires on it during a slow-speed
>>u-turn at a light-controlled intersection when it grenaded loudly enough
>>to cause people a block away to look up to see what happened. I strongly
>>recommend you not install a locker into a D35c, no matter how carefully
>>you drive it. The trouble it causes is just not worth it.
>>
>>Jerry
>>
>>Carl wrote:
>>
>>>Ya, I realize the risk. A lot of my friends run locked up D35's on large
>>>and larger tires. General rule of thumb: Drive it like its a D35. Even
>>>with the low-output 4cyl, I'm sure it will eventually break.
>>>
>>>Thanks for the input guys.. looks like I'll be going with a brand new
>>>lockright.
>>>
>>>Carl
>>>
>>>
>>>"Jerry Bransford" <jerrypb@***.net> wrote in message
>>>news:Xrn2f.2455$MN6.950@fed1read04...
>>>
>>>
>>>>Yep but the axleshafts on your Dana 35c sure are not even close to being
>>>>strong enough to run a locker and 33" tires.
>>>>
>>>>Jerry
>>>>
>>>>Carl wrote:
>>>>
>>>>
>>>>>Is a lockright strong enough for my 4cyl turning 33's?
>>>>>
>>>>>Carl
>>>>>
>>>>>"L.W. ("ßill") ------ III" <----------@***.net> wrote in message
>>>>>news:4349FC78.1EA322B2@***.net...
>>>>>
>>>>>
>>>>>
>>>>>>Hi Carl,
>>>>>> The Lock Right locker from Powertrax will slip right in place of
>>>>>>your spiders, but it's not very strong. The Detroit will take a bunch
>>>>>>of
>>>>>>precise tools and a junk drawer full of shims to bring her in, may be
>>>>>>better to let a professional take responsibility for it:
>>>>>>http://www.differentials.com/install.html
>>>>>>http://www.----------.com/dana35c/TJDana35.pdf
>>>>>> God Bless America, Bill O|||||||O
>>>>>>mailto:-------------------- http://www.----------.com/
>>>>>>
>>>>>>Carl wrote:
>>>>>>
>>>>>>
>>>>>>
>>>>>>>The one I'm looking at is in an apparently good rear end with 4.10
>>>>>>>gears.
>>>>>>>It's located far away so I told him I just want the locker. You're
>>>>>>>probably
>>>>>>>right -you usually are- .. I think I'll just shell out the $$ for a
>>>>>>>new one.
>>>>>>>
>>>>>>>Is a locker difficult to install?
>>>>>>>
>>>>>>>Carl
>>>>>
>>>>>
>>>>>
>>>>--
>>>>Jerry Bransford
>>>>PP-ASEL N6TAY
>>>>See the Geezer Jeep at
>>>>http://members.***.net/jerrypb/
>>>
>>>
>>>
>>--
>>Jerry Bransford
>>PP-ASEL N6TAY
>>See the Geezer Jeep at
>>http://members.***.net/jerrypb/
>
>
>
--
Jerry Bransford
PP-ASEL N6TAY
See the Geezer Jeep at
http://members.***.net/jerrypb/
Guest
Posts: n/a
Re: Trac - Loc
Does it matter? I was doing a u-turn and nearly coasting through it at
minimal power.
Carl wrote:
> Jerry-
> What engine?
>
> Carl
>
> "Jerry Bransford" <jerrypb@***.net> wrote in message
> news:bDn2f.2457$MN6.573@fed1read04...
>
>>My thankfully long-gone D35c axle grenaded/self-destructed 6 weeks after
>>installing a locker. The axle had 33" tires on it during a slow-speed
>>u-turn at a light-controlled intersection when it grenaded loudly enough
>>to cause people a block away to look up to see what happened. I strongly
>>recommend you not install a locker into a D35c, no matter how carefully
>>you drive it. The trouble it causes is just not worth it.
>>
>>Jerry
>>
>>Carl wrote:
>>
>>>Ya, I realize the risk. A lot of my friends run locked up D35's on large
>>>and larger tires. General rule of thumb: Drive it like its a D35. Even
>>>with the low-output 4cyl, I'm sure it will eventually break.
>>>
>>>Thanks for the input guys.. looks like I'll be going with a brand new
>>>lockright.
>>>
>>>Carl
>>>
>>>
>>>"Jerry Bransford" <jerrypb@***.net> wrote in message
>>>news:Xrn2f.2455$MN6.950@fed1read04...
>>>
>>>
>>>>Yep but the axleshafts on your Dana 35c sure are not even close to being
>>>>strong enough to run a locker and 33" tires.
>>>>
>>>>Jerry
>>>>
>>>>Carl wrote:
>>>>
>>>>
>>>>>Is a lockright strong enough for my 4cyl turning 33's?
>>>>>
>>>>>Carl
>>>>>
>>>>>"L.W. ("ßill") ------ III" <----------@***.net> wrote in message
>>>>>news:4349FC78.1EA322B2@***.net...
>>>>>
>>>>>
>>>>>
>>>>>>Hi Carl,
>>>>>> The Lock Right locker from Powertrax will slip right in place of
>>>>>>your spiders, but it's not very strong. The Detroit will take a bunch
>>>>>>of
>>>>>>precise tools and a junk drawer full of shims to bring her in, may be
>>>>>>better to let a professional take responsibility for it:
>>>>>>http://www.differentials.com/install.html
>>>>>>http://www.----------.com/dana35c/TJDana35.pdf
>>>>>> God Bless America, Bill O|||||||O
>>>>>>mailto:-------------------- http://www.----------.com/
>>>>>>
>>>>>>Carl wrote:
>>>>>>
>>>>>>
>>>>>>
>>>>>>>The one I'm looking at is in an apparently good rear end with 4.10
>>>>>>>gears.
>>>>>>>It's located far away so I told him I just want the locker. You're
>>>>>>>probably
>>>>>>>right -you usually are- .. I think I'll just shell out the $$ for a
>>>>>>>new one.
>>>>>>>
>>>>>>>Is a locker difficult to install?
>>>>>>>
>>>>>>>Carl
>>>>>
>>>>>
>>>>>
>>>>--
>>>>Jerry Bransford
>>>>PP-ASEL N6TAY
>>>>See the Geezer Jeep at
>>>>http://members.***.net/jerrypb/
>>>
>>>
>>>
>>--
>>Jerry Bransford
>>PP-ASEL N6TAY
>>See the Geezer Jeep at
>>http://members.***.net/jerrypb/
>
>
>
--
Jerry Bransford
PP-ASEL N6TAY
See the Geezer Jeep at
http://members.***.net/jerrypb/
minimal power.
Carl wrote:
> Jerry-
> What engine?
>
> Carl
>
> "Jerry Bransford" <jerrypb@***.net> wrote in message
> news:bDn2f.2457$MN6.573@fed1read04...
>
>>My thankfully long-gone D35c axle grenaded/self-destructed 6 weeks after
>>installing a locker. The axle had 33" tires on it during a slow-speed
>>u-turn at a light-controlled intersection when it grenaded loudly enough
>>to cause people a block away to look up to see what happened. I strongly
>>recommend you not install a locker into a D35c, no matter how carefully
>>you drive it. The trouble it causes is just not worth it.
>>
>>Jerry
>>
>>Carl wrote:
>>
>>>Ya, I realize the risk. A lot of my friends run locked up D35's on large
>>>and larger tires. General rule of thumb: Drive it like its a D35. Even
>>>with the low-output 4cyl, I'm sure it will eventually break.
>>>
>>>Thanks for the input guys.. looks like I'll be going with a brand new
>>>lockright.
>>>
>>>Carl
>>>
>>>
>>>"Jerry Bransford" <jerrypb@***.net> wrote in message
>>>news:Xrn2f.2455$MN6.950@fed1read04...
>>>
>>>
>>>>Yep but the axleshafts on your Dana 35c sure are not even close to being
>>>>strong enough to run a locker and 33" tires.
>>>>
>>>>Jerry
>>>>
>>>>Carl wrote:
>>>>
>>>>
>>>>>Is a lockright strong enough for my 4cyl turning 33's?
>>>>>
>>>>>Carl
>>>>>
>>>>>"L.W. ("ßill") ------ III" <----------@***.net> wrote in message
>>>>>news:4349FC78.1EA322B2@***.net...
>>>>>
>>>>>
>>>>>
>>>>>>Hi Carl,
>>>>>> The Lock Right locker from Powertrax will slip right in place of
>>>>>>your spiders, but it's not very strong. The Detroit will take a bunch
>>>>>>of
>>>>>>precise tools and a junk drawer full of shims to bring her in, may be
>>>>>>better to let a professional take responsibility for it:
>>>>>>http://www.differentials.com/install.html
>>>>>>http://www.----------.com/dana35c/TJDana35.pdf
>>>>>> God Bless America, Bill O|||||||O
>>>>>>mailto:-------------------- http://www.----------.com/
>>>>>>
>>>>>>Carl wrote:
>>>>>>
>>>>>>
>>>>>>
>>>>>>>The one I'm looking at is in an apparently good rear end with 4.10
>>>>>>>gears.
>>>>>>>It's located far away so I told him I just want the locker. You're
>>>>>>>probably
>>>>>>>right -you usually are- .. I think I'll just shell out the $$ for a
>>>>>>>new one.
>>>>>>>
>>>>>>>Is a locker difficult to install?
>>>>>>>
>>>>>>>Carl
>>>>>
>>>>>
>>>>>
>>>>--
>>>>Jerry Bransford
>>>>PP-ASEL N6TAY
>>>>See the Geezer Jeep at
>>>>http://members.***.net/jerrypb/
>>>
>>>
>>>
>>--
>>Jerry Bransford
>>PP-ASEL N6TAY
>>See the Geezer Jeep at
>>http://members.***.net/jerrypb/
>
>
>
--
Jerry Bransford
PP-ASEL N6TAY
See the Geezer Jeep at
http://members.***.net/jerrypb/
Guest
Posts: n/a
Re: Trac - Loc
Does it matter? I was doing a u-turn and nearly coasting through it at
minimal power.
Carl wrote:
> Jerry-
> What engine?
>
> Carl
>
> "Jerry Bransford" <jerrypb@***.net> wrote in message
> news:bDn2f.2457$MN6.573@fed1read04...
>
>>My thankfully long-gone D35c axle grenaded/self-destructed 6 weeks after
>>installing a locker. The axle had 33" tires on it during a slow-speed
>>u-turn at a light-controlled intersection when it grenaded loudly enough
>>to cause people a block away to look up to see what happened. I strongly
>>recommend you not install a locker into a D35c, no matter how carefully
>>you drive it. The trouble it causes is just not worth it.
>>
>>Jerry
>>
>>Carl wrote:
>>
>>>Ya, I realize the risk. A lot of my friends run locked up D35's on large
>>>and larger tires. General rule of thumb: Drive it like its a D35. Even
>>>with the low-output 4cyl, I'm sure it will eventually break.
>>>
>>>Thanks for the input guys.. looks like I'll be going with a brand new
>>>lockright.
>>>
>>>Carl
>>>
>>>
>>>"Jerry Bransford" <jerrypb@***.net> wrote in message
>>>news:Xrn2f.2455$MN6.950@fed1read04...
>>>
>>>
>>>>Yep but the axleshafts on your Dana 35c sure are not even close to being
>>>>strong enough to run a locker and 33" tires.
>>>>
>>>>Jerry
>>>>
>>>>Carl wrote:
>>>>
>>>>
>>>>>Is a lockright strong enough for my 4cyl turning 33's?
>>>>>
>>>>>Carl
>>>>>
>>>>>"L.W. ("ßill") ------ III" <----------@***.net> wrote in message
>>>>>news:4349FC78.1EA322B2@***.net...
>>>>>
>>>>>
>>>>>
>>>>>>Hi Carl,
>>>>>> The Lock Right locker from Powertrax will slip right in place of
>>>>>>your spiders, but it's not very strong. The Detroit will take a bunch
>>>>>>of
>>>>>>precise tools and a junk drawer full of shims to bring her in, may be
>>>>>>better to let a professional take responsibility for it:
>>>>>>http://www.differentials.com/install.html
>>>>>>http://www.----------.com/dana35c/TJDana35.pdf
>>>>>> God Bless America, Bill O|||||||O
>>>>>>mailto:-------------------- http://www.----------.com/
>>>>>>
>>>>>>Carl wrote:
>>>>>>
>>>>>>
>>>>>>
>>>>>>>The one I'm looking at is in an apparently good rear end with 4.10
>>>>>>>gears.
>>>>>>>It's located far away so I told him I just want the locker. You're
>>>>>>>probably
>>>>>>>right -you usually are- .. I think I'll just shell out the $$ for a
>>>>>>>new one.
>>>>>>>
>>>>>>>Is a locker difficult to install?
>>>>>>>
>>>>>>>Carl
>>>>>
>>>>>
>>>>>
>>>>--
>>>>Jerry Bransford
>>>>PP-ASEL N6TAY
>>>>See the Geezer Jeep at
>>>>http://members.***.net/jerrypb/
>>>
>>>
>>>
>>--
>>Jerry Bransford
>>PP-ASEL N6TAY
>>See the Geezer Jeep at
>>http://members.***.net/jerrypb/
>
>
>
--
Jerry Bransford
PP-ASEL N6TAY
See the Geezer Jeep at
http://members.***.net/jerrypb/
minimal power.
Carl wrote:
> Jerry-
> What engine?
>
> Carl
>
> "Jerry Bransford" <jerrypb@***.net> wrote in message
> news:bDn2f.2457$MN6.573@fed1read04...
>
>>My thankfully long-gone D35c axle grenaded/self-destructed 6 weeks after
>>installing a locker. The axle had 33" tires on it during a slow-speed
>>u-turn at a light-controlled intersection when it grenaded loudly enough
>>to cause people a block away to look up to see what happened. I strongly
>>recommend you not install a locker into a D35c, no matter how carefully
>>you drive it. The trouble it causes is just not worth it.
>>
>>Jerry
>>
>>Carl wrote:
>>
>>>Ya, I realize the risk. A lot of my friends run locked up D35's on large
>>>and larger tires. General rule of thumb: Drive it like its a D35. Even
>>>with the low-output 4cyl, I'm sure it will eventually break.
>>>
>>>Thanks for the input guys.. looks like I'll be going with a brand new
>>>lockright.
>>>
>>>Carl
>>>
>>>
>>>"Jerry Bransford" <jerrypb@***.net> wrote in message
>>>news:Xrn2f.2455$MN6.950@fed1read04...
>>>
>>>
>>>>Yep but the axleshafts on your Dana 35c sure are not even close to being
>>>>strong enough to run a locker and 33" tires.
>>>>
>>>>Jerry
>>>>
>>>>Carl wrote:
>>>>
>>>>
>>>>>Is a lockright strong enough for my 4cyl turning 33's?
>>>>>
>>>>>Carl
>>>>>
>>>>>"L.W. ("ßill") ------ III" <----------@***.net> wrote in message
>>>>>news:4349FC78.1EA322B2@***.net...
>>>>>
>>>>>
>>>>>
>>>>>>Hi Carl,
>>>>>> The Lock Right locker from Powertrax will slip right in place of
>>>>>>your spiders, but it's not very strong. The Detroit will take a bunch
>>>>>>of
>>>>>>precise tools and a junk drawer full of shims to bring her in, may be
>>>>>>better to let a professional take responsibility for it:
>>>>>>http://www.differentials.com/install.html
>>>>>>http://www.----------.com/dana35c/TJDana35.pdf
>>>>>> God Bless America, Bill O|||||||O
>>>>>>mailto:-------------------- http://www.----------.com/
>>>>>>
>>>>>>Carl wrote:
>>>>>>
>>>>>>
>>>>>>
>>>>>>>The one I'm looking at is in an apparently good rear end with 4.10
>>>>>>>gears.
>>>>>>>It's located far away so I told him I just want the locker. You're
>>>>>>>probably
>>>>>>>right -you usually are- .. I think I'll just shell out the $$ for a
>>>>>>>new one.
>>>>>>>
>>>>>>>Is a locker difficult to install?
>>>>>>>
>>>>>>>Carl
>>>>>
>>>>>
>>>>>
>>>>--
>>>>Jerry Bransford
>>>>PP-ASEL N6TAY
>>>>See the Geezer Jeep at
>>>>http://members.***.net/jerrypb/
>>>
>>>
>>>
>>--
>>Jerry Bransford
>>PP-ASEL N6TAY
>>See the Geezer Jeep at
>>http://members.***.net/jerrypb/
>
>
>
--
Jerry Bransford
PP-ASEL N6TAY
See the Geezer Jeep at
http://members.***.net/jerrypb/
Guest
Posts: n/a
Re: Trac - Loc
So am I better off gettin a posi instead of a locker? Am I less likely to
break with a posi?
Carl
"Greg" <greglc84@hotmail.com> wrote in message
news:6yu2f.137206$oW2.31315@pd7tw1no...
> Like bill said, that looks like an open carrier taken out after putting a
> detroit in, go have a look here for your prices and pictures
> http://completeoffroad.com/wsm/c-15_dana__35_m35.html unfortunately they
> don't have a pic of the dana 35 detroit, but you could look at the D 44, D
> 30, 9" ones etc. Good place to buy from, best I found on the net for
> prices, I am in Canada and saved $200.00 on my daughter's 9" detroit and
> $250.00 on my AMC 20 detroit.
> Greg
>
> "Carl" <carlsaiyed@REMOVE.hotmail.com> wrote in message
> news:MN2dnfQtbKP9n9feRVn-uA@comcast.com...
>> Wow, so he is ripping someone off?
>>
>> Carl
>>
>> "L.W. ("ßill") ------ III" <----------@***.net> wrote in message
>> news:434A00A2.C6148F25@***.net...
>>> Hi Carl,
>>> That's what I hate about EBay! What you're looking at is the Locker
>>> box and the old stock open differential. The Detroit will look machined
>>> like the one at: http://www.4x4wire.com/jeep/reviews/super35d/
>>> God Bless America, Bill O|||||||O
>>> mailto:-------------------- http://www.----------.com/
>>>
>>> Carl wrote:
>>>>
>>>> Bill-
>>>> What about this one?
>>>> http://cgi.ebay.com/ebaymotors/ws/eB...tem=8004904578
>>>>
>>>> Carl
>>
>>
>
>
break with a posi?
Carl
"Greg" <greglc84@hotmail.com> wrote in message
news:6yu2f.137206$oW2.31315@pd7tw1no...
> Like bill said, that looks like an open carrier taken out after putting a
> detroit in, go have a look here for your prices and pictures
> http://completeoffroad.com/wsm/c-15_dana__35_m35.html unfortunately they
> don't have a pic of the dana 35 detroit, but you could look at the D 44, D
> 30, 9" ones etc. Good place to buy from, best I found on the net for
> prices, I am in Canada and saved $200.00 on my daughter's 9" detroit and
> $250.00 on my AMC 20 detroit.
> Greg
>
> "Carl" <carlsaiyed@REMOVE.hotmail.com> wrote in message
> news:MN2dnfQtbKP9n9feRVn-uA@comcast.com...
>> Wow, so he is ripping someone off?
>>
>> Carl
>>
>> "L.W. ("ßill") ------ III" <----------@***.net> wrote in message
>> news:434A00A2.C6148F25@***.net...
>>> Hi Carl,
>>> That's what I hate about EBay! What you're looking at is the Locker
>>> box and the old stock open differential. The Detroit will look machined
>>> like the one at: http://www.4x4wire.com/jeep/reviews/super35d/
>>> God Bless America, Bill O|||||||O
>>> mailto:-------------------- http://www.----------.com/
>>>
>>> Carl wrote:
>>>>
>>>> Bill-
>>>> What about this one?
>>>> http://cgi.ebay.com/ebaymotors/ws/eB...tem=8004904578
>>>>
>>>> Carl
>>
>>
>
>
Guest
Posts: n/a
Re: Trac - Loc
So am I better off gettin a posi instead of a locker? Am I less likely to
break with a posi?
Carl
"Greg" <greglc84@hotmail.com> wrote in message
news:6yu2f.137206$oW2.31315@pd7tw1no...
> Like bill said, that looks like an open carrier taken out after putting a
> detroit in, go have a look here for your prices and pictures
> http://completeoffroad.com/wsm/c-15_dana__35_m35.html unfortunately they
> don't have a pic of the dana 35 detroit, but you could look at the D 44, D
> 30, 9" ones etc. Good place to buy from, best I found on the net for
> prices, I am in Canada and saved $200.00 on my daughter's 9" detroit and
> $250.00 on my AMC 20 detroit.
> Greg
>
> "Carl" <carlsaiyed@REMOVE.hotmail.com> wrote in message
> news:MN2dnfQtbKP9n9feRVn-uA@comcast.com...
>> Wow, so he is ripping someone off?
>>
>> Carl
>>
>> "L.W. ("ßill") ------ III" <----------@***.net> wrote in message
>> news:434A00A2.C6148F25@***.net...
>>> Hi Carl,
>>> That's what I hate about EBay! What you're looking at is the Locker
>>> box and the old stock open differential. The Detroit will look machined
>>> like the one at: http://www.4x4wire.com/jeep/reviews/super35d/
>>> God Bless America, Bill O|||||||O
>>> mailto:-------------------- http://www.----------.com/
>>>
>>> Carl wrote:
>>>>
>>>> Bill-
>>>> What about this one?
>>>> http://cgi.ebay.com/ebaymotors/ws/eB...tem=8004904578
>>>>
>>>> Carl
>>
>>
>
>
break with a posi?
Carl
"Greg" <greglc84@hotmail.com> wrote in message
news:6yu2f.137206$oW2.31315@pd7tw1no...
> Like bill said, that looks like an open carrier taken out after putting a
> detroit in, go have a look here for your prices and pictures
> http://completeoffroad.com/wsm/c-15_dana__35_m35.html unfortunately they
> don't have a pic of the dana 35 detroit, but you could look at the D 44, D
> 30, 9" ones etc. Good place to buy from, best I found on the net for
> prices, I am in Canada and saved $200.00 on my daughter's 9" detroit and
> $250.00 on my AMC 20 detroit.
> Greg
>
> "Carl" <carlsaiyed@REMOVE.hotmail.com> wrote in message
> news:MN2dnfQtbKP9n9feRVn-uA@comcast.com...
>> Wow, so he is ripping someone off?
>>
>> Carl
>>
>> "L.W. ("ßill") ------ III" <----------@***.net> wrote in message
>> news:434A00A2.C6148F25@***.net...
>>> Hi Carl,
>>> That's what I hate about EBay! What you're looking at is the Locker
>>> box and the old stock open differential. The Detroit will look machined
>>> like the one at: http://www.4x4wire.com/jeep/reviews/super35d/
>>> God Bless America, Bill O|||||||O
>>> mailto:-------------------- http://www.----------.com/
>>>
>>> Carl wrote:
>>>>
>>>> Bill-
>>>> What about this one?
>>>> http://cgi.ebay.com/ebaymotors/ws/eB...tem=8004904578
>>>>
>>>> Carl
>>
>>
>
>
