add flat bladed cuts the the bolts after cutting heads so u can use a screw
driver to remove the studs u made

Carl wrote:

> Pull one bolt from the bellhousing, take it to the hardware store. Get 4
> just like it, but 5 or so inches longer. When you get home, cut the heads
> off and taper the ends. Install the 4 rods you made when you take out the 4
> lower bellhousing bolts. This will allow the trans to slide back free of the
> pilot bearing upon removal, and will make alignment for re-install VERY
> easy.
>
> HTH
>
> Carl
>
> "JimG" <JimG@nospam.com> wrote in message
> news:kaaCg.7179$oa1.1429@news02.roc.ny...
> > The tranny has locked up again in neutral... this time it ain't comin'
> > out. Any words of wisdom before I yank it out?
> > happened once before several months ago... but I jiggled, pounded, etc.
> > and it started working again. Stick shift goes left to right but wont go
> > in any gear.... engine off/on, clutch in/out, rock back and forth... all
> > that stuff. NV3550 my ars!#@*#
> > --
> > --
> > JimG
> > 80' CJ-7 258 CID, HEI
> > 4.56 Gears, Lock-Right F&R
> > 35" BFG MT on 15x10 Centerlines
> > D44 Rear, D30 Front. SOA
> > Dana 300 w/4:1 & Currie twin sticks
> > Warn X8000i w/ dual batteries
> >
> > 00' TJ Sport 4.0L, 5sp
> > 4.56 Gears, TrueTrac rear
> > 33" BFG AT on 15x8 Eagle Alloys
> > D35 Rear, D30 Front. 3" Suspension Lift
> > Warn X8000i
> >
> >

 

add flat bladed cuts the the bolts after cutting heads so u can use a screw
driver to remove the studs u made

Carl wrote:

> Pull one bolt from the bellhousing, take it to the hardware store. Get 4
> just like it, but 5 or so inches longer. When you get home, cut the heads
> off and taper the ends. Install the 4 rods you made when you take out the 4
> lower bellhousing bolts. This will allow the trans to slide back free of the
> pilot bearing upon removal, and will make alignment for re-install VERY
> easy.
>
> HTH
>
> Carl
>
> "JimG" <JimG@nospam.com> wrote in message
> news:kaaCg.7179$oa1.1429@news02.roc.ny...
> > The tranny has locked up again in neutral... this time it ain't comin'
> > out. Any words of wisdom before I yank it out?
> > happened once before several months ago... but I jiggled, pounded, etc.
> > and it started working again. Stick shift goes left to right but wont go
> > in any gear.... engine off/on, clutch in/out, rock back and forth... all
> > that stuff. NV3550 my ars!#@*#
> > --
> > --
> > JimG
> > 80' CJ-7 258 CID, HEI
> > 4.56 Gears, Lock-Right F&R
> > 35" BFG MT on 15x10 Centerlines
> > D44 Rear, D30 Front. SOA
> > Dana 300 w/4:1 & Currie twin sticks
> > Warn X8000i w/ dual batteries
> >
> > 00' TJ Sport 4.0L, 5sp
> > 4.56 Gears, TrueTrac rear
> > 33" BFG AT on 15x8 Eagle Alloys
> > D35 Rear, D30 Front. 3" Suspension Lift
> > Warn X8000i
> >
> >

 

add flat bladed cuts the the bolts after cutting heads so u can use a screw
driver to remove the studs u made

Carl wrote:

> Pull one bolt from the bellhousing, take it to the hardware store. Get 4
> just like it, but 5 or so inches longer. When you get home, cut the heads
> off and taper the ends. Install the 4 rods you made when you take out the 4
> lower bellhousing bolts. This will allow the trans to slide back free of the
> pilot bearing upon removal, and will make alignment for re-install VERY
> easy.
>
> HTH
>
> Carl
>
> "JimG" <JimG@nospam.com> wrote in message
> news:kaaCg.7179$oa1.1429@news02.roc.ny...
> > The tranny has locked up again in neutral... this time it ain't comin'
> > out. Any words of wisdom before I yank it out?
> > happened once before several months ago... but I jiggled, pounded, etc.
> > and it started working again. Stick shift goes left to right but wont go
> > in any gear.... engine off/on, clutch in/out, rock back and forth... all
> > that stuff. NV3550 my ars!#@*#
> > --
> > --
> > JimG
> > 80' CJ-7 258 CID, HEI
> > 4.56 Gears, Lock-Right F&R
> > 35" BFG MT on 15x10 Centerlines
> > D44 Rear, D30 Front. SOA
> > Dana 300 w/4:1 & Currie twin sticks
> > Warn X8000i w/ dual batteries
> >
> > 00' TJ Sport 4.0L, 5sp
> > 4.56 Gears, TrueTrac rear
> > 33" BFG AT on 15x8 Eagle Alloys
> > D35 Rear, D30 Front. 3" Suspension Lift
> > Warn X8000i
> >
> >

 

Sorry, not much good at voodoo (see my other post). Hope the idea helps.. I
got it on here from (I THINK) Mike R.

Carl


"JimG" <JimG@nospam.com> wrote in message
news:IoaCg.7183$oa1.3361@news02.roc.ny...
> Cool idea... Thanks! But I was hoping you would say something like...
> "turn hat to left side, stick tongue out to right side, close one eye and
> pull shifter back while standing on left foot only".
>
>
> "Carl" <carlsaiyed@hotmailREMOVE.com> wrote in message
> news:kvidnbsKz-pTskTZnZ2dnUVZ_oSdnZ2d@comcast.com...
>> Pull one bolt from the bellhousing, take it to the hardware store. Get 4
>> just like it, but 5 or so inches longer. When you get home, cut the heads
>> off and taper the ends. Install the 4 rods you made when you take out the
>> 4 lower bellhousing bolts. This will allow the trans to slide back free
>> of the pilot bearing upon removal, and will make alignment for re-install
>> VERY easy.
>>
>> HTH
>>
>> Carl
>>
>>
>> "JimG" <JimG@nospam.com> wrote in message
>> news:kaaCg.7179$oa1.1429@news02.roc.ny...
>>> The tranny has locked up again in neutral... this time it ain't comin'
>>> out. Any words of wisdom before I yank it out?
>>> happened once before several months ago... but I jiggled, pounded, etc.
>>> and it started working again. Stick shift goes left to right but wont
>>> go in any gear.... engine off/on, clutch in/out, rock back and forth...
>>> all that stuff. NV3550 my ars!#@*#
>>> --
>>> --
>>> JimG
>>> 80' CJ-7 258 CID, HEI
>>> 4.56 Gears, Lock-Right F&R
>>> 35" BFG MT on 15x10 Centerlines
>>> D44 Rear, D30 Front. SOA
>>> Dana 300 w/4:1 & Currie twin sticks
>>> Warn X8000i w/ dual batteries
>>>
>>> 00' TJ Sport 4.0L, 5sp
>>> 4.56 Gears, TrueTrac rear
>>> 33" BFG AT on 15x8 Eagle Alloys
>>> D35 Rear, D30 Front. 3" Suspension Lift
>>> Warn X8000i
>>>
>>>
>>
>>
>
>

 

Sorry, not much good at voodoo (see my other post). Hope the idea helps.. I
got it on here from (I THINK) Mike R.

Carl


"JimG" <JimG@nospam.com> wrote in message
news:IoaCg.7183$oa1.3361@news02.roc.ny...
> Cool idea... Thanks! But I was hoping you would say something like...
> "turn hat to left side, stick tongue out to right side, close one eye and
> pull shifter back while standing on left foot only".
>
>
> "Carl" <carlsaiyed@hotmailREMOVE.com> wrote in message
> news:kvidnbsKz-pTskTZnZ2dnUVZ_oSdnZ2d@comcast.com...
>> Pull one bolt from the bellhousing, take it to the hardware store. Get 4
>> just like it, but 5 or so inches longer. When you get home, cut the heads
>> off and taper the ends. Install the 4 rods you made when you take out the
>> 4 lower bellhousing bolts. This will allow the trans to slide back free
>> of the pilot bearing upon removal, and will make alignment for re-install
>> VERY easy.
>>
>> HTH
>>
>> Carl
>>
>>
>> "JimG" <JimG@nospam.com> wrote in message
>> news:kaaCg.7179$oa1.1429@news02.roc.ny...
>>> The tranny has locked up again in neutral... this time it ain't comin'
>>> out. Any words of wisdom before I yank it out?
>>> happened once before several months ago... but I jiggled, pounded, etc.
>>> and it started working again. Stick shift goes left to right but wont
>>> go in any gear.... engine off/on, clutch in/out, rock back and forth...
>>> all that stuff. NV3550 my ars!#@*#
>>> --
>>> --
>>> JimG
>>> 80' CJ-7 258 CID, HEI
>>> 4.56 Gears, Lock-Right F&R
>>> 35" BFG MT on 15x10 Centerlines
>>> D44 Rear, D30 Front. SOA
>>> Dana 300 w/4:1 & Currie twin sticks
>>> Warn X8000i w/ dual batteries
>>>
>>> 00' TJ Sport 4.0L, 5sp
>>> 4.56 Gears, TrueTrac rear
>>> 33" BFG AT on 15x8 Eagle Alloys
>>> D35 Rear, D30 Front. 3" Suspension Lift
>>> Warn X8000i
>>>
>>>
>>
>>
>
>

 

Sorry, not much good at voodoo (see my other post). Hope the idea helps.. I
got it on here from (I THINK) Mike R.

Carl


"JimG" <JimG@nospam.com> wrote in message
news:IoaCg.7183$oa1.3361@news02.roc.ny...
> Cool idea... Thanks! But I was hoping you would say something like...
> "turn hat to left side, stick tongue out to right side, close one eye and
> pull shifter back while standing on left foot only".
>
>
> "Carl" <carlsaiyed@hotmailREMOVE.com> wrote in message
> news:kvidnbsKz-pTskTZnZ2dnUVZ_oSdnZ2d@comcast.com...
>> Pull one bolt from the bellhousing, take it to the hardware store. Get 4
>> just like it, but 5 or so inches longer. When you get home, cut the heads
>> off and taper the ends. Install the 4 rods you made when you take out the
>> 4 lower bellhousing bolts. This will allow the trans to slide back free
>> of the pilot bearing upon removal, and will make alignment for re-install
>> VERY easy.
>>
>> HTH
>>
>> Carl
>>
>>
>> "JimG" <JimG@nospam.com> wrote in message
>> news:kaaCg.7179$oa1.1429@news02.roc.ny...
>>> The tranny has locked up again in neutral... this time it ain't comin'
>>> out. Any words of wisdom before I yank it out?
>>> happened once before several months ago... but I jiggled, pounded, etc.
>>> and it started working again. Stick shift goes left to right but wont
>>> go in any gear.... engine off/on, clutch in/out, rock back and forth...
>>> all that stuff. NV3550 my ars!#@*#
>>> --
>>> --
>>> JimG
>>> 80' CJ-7 258 CID, HEI
>>> 4.56 Gears, Lock-Right F&R
>>> 35" BFG MT on 15x10 Centerlines
>>> D44 Rear, D30 Front. SOA
>>> Dana 300 w/4:1 & Currie twin sticks
>>> Warn X8000i w/ dual batteries
>>>
>>> 00' TJ Sport 4.0L, 5sp
>>> 4.56 Gears, TrueTrac rear
>>> 33" BFG AT on 15x8 Eagle Alloys
>>> D35 Rear, D30 Front. 3" Suspension Lift
>>> Warn X8000i
>>>
>>>
>>
>>
>
>

 

Sorry, not much good at voodoo (see my other post). Hope the idea helps.. I
got it on here from (I THINK) Mike R.

Carl


"JimG" <JimG@nospam.com> wrote in message
news:IoaCg.7183$oa1.3361@news02.roc.ny...
> Cool idea... Thanks! But I was hoping you would say something like...
> "turn hat to left side, stick tongue out to right side, close one eye and
> pull shifter back while standing on left foot only".
>
>
> "Carl" <carlsaiyed@hotmailREMOVE.com> wrote in message
> news:kvidnbsKz-pTskTZnZ2dnUVZ_oSdnZ2d@comcast.com...
>> Pull one bolt from the bellhousing, take it to the hardware store. Get 4
>> just like it, but 5 or so inches longer. When you get home, cut the heads
>> off and taper the ends. Install the 4 rods you made when you take out the
>> 4 lower bellhousing bolts. This will allow the trans to slide back free
>> of the pilot bearing upon removal, and will make alignment for re-install
>> VERY easy.
>>
>> HTH
>>
>> Carl
>>
>>
>> "JimG" <JimG@nospam.com> wrote in message
>> news:kaaCg.7179$oa1.1429@news02.roc.ny...
>>> The tranny has locked up again in neutral... this time it ain't comin'
>>> out. Any words of wisdom before I yank it out?
>>> happened once before several months ago... but I jiggled, pounded, etc.
>>> and it started working again. Stick shift goes left to right but wont
>>> go in any gear.... engine off/on, clutch in/out, rock back and forth...
>>> all that stuff. NV3550 my ars!#@*#
>>> --
>>> --
>>> JimG
>>> 80' CJ-7 258 CID, HEI
>>> 4.56 Gears, Lock-Right F&R
>>> 35" BFG MT on 15x10 Centerlines
>>> D44 Rear, D30 Front. SOA
>>> Dana 300 w/4:1 & Currie twin sticks
>>> Warn X8000i w/ dual batteries
>>>
>>> 00' TJ Sport 4.0L, 5sp
>>> 4.56 Gears, TrueTrac rear
>>> 33" BFG AT on 15x8 Eagle Alloys
>>> D35 Rear, D30 Front. 3" Suspension Lift
>>> Warn X8000i
>>>
>>>
>>
>>
>
>

 

It is the right foot and you have to curl your tongue and rotate it counter
clockwise while humming 'The Motorcycle Song' backwards in Polish.


"JimG" <JimG@nospam.com> wrote in message
news:IoaCg.7183$oa1.3361@news02.roc.ny...
> Cool idea... Thanks! But I was hoping you would say something like...
> "turn hat to left side, stick tongue out to right side, close one eye and
> pull shifter back while standing on left foot only".
>
>
> "Carl" <carlsaiyed@hotmailREMOVE.com> wrote in message
> news:kvidnbsKz-pTskTZnZ2dnUVZ_oSdnZ2d@comcast.com...
>> Pull one bolt from the bellhousing, take it to the hardware store. Get 4
>> just like it, but 5 or so inches longer. When you get home, cut the heads
>> off and taper the ends. Install the 4 rods you made when you take out the
>> 4 lower bellhousing bolts. This will allow the trans to slide back free
>> of the pilot bearing upon removal, and will make alignment for re-install
>> VERY easy.
>>
>> HTH
>>
>> Carl
>>
>>
>> "JimG" <JimG@nospam.com> wrote in message
>> news:kaaCg.7179$oa1.1429@news02.roc.ny...
>>> The tranny has locked up again in neutral... this time it ain't comin'
>>> out. Any words of wisdom before I yank it out?
>>> happened once before several months ago... but I jiggled, pounded, etc.
>>> and it started working again. Stick shift goes left to right but wont
>>> go in any gear.... engine off/on, clutch in/out, rock back and forth...
>>> all that stuff. NV3550 my ars!#@*#
>>> --
>>> --
>>> JimG
>>> 80' CJ-7 258 CID, HEI
>>> 4.56 Gears, Lock-Right F&R
>>> 35" BFG MT on 15x10 Centerlines
>>> D44 Rear, D30 Front. SOA
>>> Dana 300 w/4:1 & Currie twin sticks
>>> Warn X8000i w/ dual batteries
>>>
>>> 00' TJ Sport 4.0L, 5sp
>>> 4.56 Gears, TrueTrac rear
>>> 33" BFG AT on 15x8 Eagle Alloys
>>> D35 Rear, D30 Front. 3" Suspension Lift
>>> Warn X8000i
>>>
>>>
>>
>>
>
>

 

It is the right foot and you have to curl your tongue and rotate it counter
clockwise while humming 'The Motorcycle Song' backwards in Polish.


"JimG" <JimG@nospam.com> wrote in message
news:IoaCg.7183$oa1.3361@news02.roc.ny...
> Cool idea... Thanks! But I was hoping you would say something like...
> "turn hat to left side, stick tongue out to right side, close one eye and
> pull shifter back while standing on left foot only".
>
>
> "Carl" <carlsaiyed@hotmailREMOVE.com> wrote in message
> news:kvidnbsKz-pTskTZnZ2dnUVZ_oSdnZ2d@comcast.com...
>> Pull one bolt from the bellhousing, take it to the hardware store. Get 4
>> just like it, but 5 or so inches longer. When you get home, cut the heads
>> off and taper the ends. Install the 4 rods you made when you take out the
>> 4 lower bellhousing bolts. This will allow the trans to slide back free
>> of the pilot bearing upon removal, and will make alignment for re-install
>> VERY easy.
>>
>> HTH
>>
>> Carl
>>
>>
>> "JimG" <JimG@nospam.com> wrote in message
>> news:kaaCg.7179$oa1.1429@news02.roc.ny...
>>> The tranny has locked up again in neutral... this time it ain't comin'
>>> out. Any words of wisdom before I yank it out?
>>> happened once before several months ago... but I jiggled, pounded, etc.
>>> and it started working again. Stick shift goes left to right but wont
>>> go in any gear.... engine off/on, clutch in/out, rock back and forth...
>>> all that stuff. NV3550 my ars!#@*#
>>> --
>>> --
>>> JimG
>>> 80' CJ-7 258 CID, HEI
>>> 4.56 Gears, Lock-Right F&R
>>> 35" BFG MT on 15x10 Centerlines
>>> D44 Rear, D30 Front. SOA
>>> Dana 300 w/4:1 & Currie twin sticks
>>> Warn X8000i w/ dual batteries
>>>
>>> 00' TJ Sport 4.0L, 5sp
>>> 4.56 Gears, TrueTrac rear
>>> 33" BFG AT on 15x8 Eagle Alloys
>>> D35 Rear, D30 Front. 3" Suspension Lift
>>> Warn X8000i
>>>
>>>
>>
>>
>
>

 

It is the right foot and you have to curl your tongue and rotate it counter
clockwise while humming 'The Motorcycle Song' backwards in Polish.


"JimG" <JimG@nospam.com> wrote in message
news:IoaCg.7183$oa1.3361@news02.roc.ny...
> Cool idea... Thanks! But I was hoping you would say something like...
> "turn hat to left side, stick tongue out to right side, close one eye and
> pull shifter back while standing on left foot only".
>
>
> "Carl" <carlsaiyed@hotmailREMOVE.com> wrote in message
> news:kvidnbsKz-pTskTZnZ2dnUVZ_oSdnZ2d@comcast.com...
>> Pull one bolt from the bellhousing, take it to the hardware store. Get 4
>> just like it, but 5 or so inches longer. When you get home, cut the heads
>> off and taper the ends. Install the 4 rods you made when you take out the
>> 4 lower bellhousing bolts. This will allow the trans to slide back free
>> of the pilot bearing upon removal, and will make alignment for re-install
>> VERY easy.
>>
>> HTH
>>
>> Carl
>>
>>
>> "JimG" <JimG@nospam.com> wrote in message
>> news:kaaCg.7179$oa1.1429@news02.roc.ny...
>>> The tranny has locked up again in neutral... this time it ain't comin'
>>> out. Any words of wisdom before I yank it out?
>>> happened once before several months ago... but I jiggled, pounded, etc.
>>> and it started working again. Stick shift goes left to right but wont
>>> go in any gear.... engine off/on, clutch in/out, rock back and forth...
>>> all that stuff. NV3550 my ars!#@*#
>>> --
>>> --
>>> JimG
>>> 80' CJ-7 258 CID, HEI
>>> 4.56 Gears, Lock-Right F&R
>>> 35" BFG MT on 15x10 Centerlines
>>> D44 Rear, D30 Front. SOA
>>> Dana 300 w/4:1 & Currie twin sticks
>>> Warn X8000i w/ dual batteries
>>>
>>> 00' TJ Sport 4.0L, 5sp
>>> 4.56 Gears, TrueTrac rear
>>> 33" BFG AT on 15x8 Eagle Alloys
>>> D35 Rear, D30 Front. 3" Suspension Lift
>>> Warn X8000i
>>>
>>>
>>
>>
>
>