TJ tranny locked up... again! Help!
 

The tranny has locked up again in neutral... this time it ain't comin' out.
Any words of wisdom before I yank it out?
happened once before several months ago... but I jiggled, pounded, etc. and
it started working again. Stick shift goes left to right but wont go in any
gear.... engine off/on, clutch in/out, rock back and forth... all that
stuff. NV3550 my ars!#@*#
--
--
JimG
80' CJ-7 258 CID, HEI
4.56 Gears, Lock-Right F&R
35" BFG MT on 15x10 Centerlines
D44 Rear, D30 Front. SOA
Dana 300 w/4:1 & Currie twin sticks
Warn X8000i w/ dual batteries

00' TJ Sport 4.0L, 5sp
4.56 Gears, TrueTrac rear
33" BFG AT on 15x8 Eagle Alloys
D35 Rear, D30 Front. 3" Suspension Lift
Warn X8000i

Re: TJ tranny locked up... again! Help!
 

Pull one bolt from the bellhousing, take it to the hardware store. Get 4
just like it, but 5 or so inches longer. When you get home, cut the heads
off and taper the ends. Install the 4 rods you made when you take out the 4
lower bellhousing bolts. This will allow the trans to slide back free of the
pilot bearing upon removal, and will make alignment for re-install VERY
easy.

HTH

Carl


"JimG" <JimG@nospam.com> wrote in message
news:kaaCg.7179$oa1.1429@news02.roc.ny...
> The tranny has locked up again in neutral... this time it ain't comin'
> out. Any words of wisdom before I yank it out?
> happened once before several months ago... but I jiggled, pounded, etc.
> and it started working again. Stick shift goes left to right but wont go
> in any gear.... engine off/on, clutch in/out, rock back and forth... all
> that stuff. NV3550 my ars!#@*#
> --
> --
> JimG
> 80' CJ-7 258 CID, HEI
> 4.56 Gears, Lock-Right F&R
> 35" BFG MT on 15x10 Centerlines
> D44 Rear, D30 Front. SOA
> Dana 300 w/4:1 & Currie twin sticks
> Warn X8000i w/ dual batteries
>
> 00' TJ Sport 4.0L, 5sp
> 4.56 Gears, TrueTrac rear
> 33" BFG AT on 15x8 Eagle Alloys
> D35 Rear, D30 Front. 3" Suspension Lift
> Warn X8000i
>
>

Re: TJ tranny locked up... again! Help!
 

Pull one bolt from the bellhousing, take it to the hardware store. Get 4
just like it, but 5 or so inches longer. When you get home, cut the heads
off and taper the ends. Install the 4 rods you made when you take out the 4
lower bellhousing bolts. This will allow the trans to slide back free of the
pilot bearing upon removal, and will make alignment for re-install VERY
easy.

HTH

Carl


"JimG" <JimG@nospam.com> wrote in message
news:kaaCg.7179$oa1.1429@news02.roc.ny...
> The tranny has locked up again in neutral... this time it ain't comin'
> out. Any words of wisdom before I yank it out?
> happened once before several months ago... but I jiggled, pounded, etc.
> and it started working again. Stick shift goes left to right but wont go
> in any gear.... engine off/on, clutch in/out, rock back and forth... all
> that stuff. NV3550 my ars!#@*#
> --
> --
> JimG
> 80' CJ-7 258 CID, HEI
> 4.56 Gears, Lock-Right F&R
> 35" BFG MT on 15x10 Centerlines
> D44 Rear, D30 Front. SOA
> Dana 300 w/4:1 & Currie twin sticks
> Warn X8000i w/ dual batteries
>
> 00' TJ Sport 4.0L, 5sp
> 4.56 Gears, TrueTrac rear
> 33" BFG AT on 15x8 Eagle Alloys
> D35 Rear, D30 Front. 3" Suspension Lift
> Warn X8000i
>
>

Re: TJ tranny locked up... again! Help!
 

Pull one bolt from the bellhousing, take it to the hardware store. Get 4
just like it, but 5 or so inches longer. When you get home, cut the heads
off and taper the ends. Install the 4 rods you made when you take out the 4
lower bellhousing bolts. This will allow the trans to slide back free of the
pilot bearing upon removal, and will make alignment for re-install VERY
easy.

HTH

Carl


"JimG" <JimG@nospam.com> wrote in message
news:kaaCg.7179$oa1.1429@news02.roc.ny...
> The tranny has locked up again in neutral... this time it ain't comin'
> out. Any words of wisdom before I yank it out?
> happened once before several months ago... but I jiggled, pounded, etc.
> and it started working again. Stick shift goes left to right but wont go
> in any gear.... engine off/on, clutch in/out, rock back and forth... all
> that stuff. NV3550 my ars!#@*#
> --
> --
> JimG
> 80' CJ-7 258 CID, HEI
> 4.56 Gears, Lock-Right F&R
> 35" BFG MT on 15x10 Centerlines
> D44 Rear, D30 Front. SOA
> Dana 300 w/4:1 & Currie twin sticks
> Warn X8000i w/ dual batteries
>
> 00' TJ Sport 4.0L, 5sp
> 4.56 Gears, TrueTrac rear
> 33" BFG AT on 15x8 Eagle Alloys
> D35 Rear, D30 Front. 3" Suspension Lift
> Warn X8000i
>
>

Re: TJ tranny locked up... again! Help!
 

Pull one bolt from the bellhousing, take it to the hardware store. Get 4
just like it, but 5 or so inches longer. When you get home, cut the heads
off and taper the ends. Install the 4 rods you made when you take out the 4
lower bellhousing bolts. This will allow the trans to slide back free of the
pilot bearing upon removal, and will make alignment for re-install VERY
easy.

HTH

Carl


"JimG" <JimG@nospam.com> wrote in message
news:kaaCg.7179$oa1.1429@news02.roc.ny...
> The tranny has locked up again in neutral... this time it ain't comin'
> out. Any words of wisdom before I yank it out?
> happened once before several months ago... but I jiggled, pounded, etc.
> and it started working again. Stick shift goes left to right but wont go
> in any gear.... engine off/on, clutch in/out, rock back and forth... all
> that stuff. NV3550 my ars!#@*#
> --
> --
> JimG
> 80' CJ-7 258 CID, HEI
> 4.56 Gears, Lock-Right F&R
> 35" BFG MT on 15x10 Centerlines
> D44 Rear, D30 Front. SOA
> Dana 300 w/4:1 & Currie twin sticks
> Warn X8000i w/ dual batteries
>
> 00' TJ Sport 4.0L, 5sp
> 4.56 Gears, TrueTrac rear
> 33" BFG AT on 15x8 Eagle Alloys
> D35 Rear, D30 Front. 3" Suspension Lift
> Warn X8000i
>
>

Re: TJ tranny locked up... again! Help!
 

Cool idea... Thanks! But I was hoping you would say something like... "turn
hat to left side, stick tongue out to right side, close one eye and pull
shifter back while standing on left foot only".


"Carl" <carlsaiyed@hotmailREMOVE.com> wrote in message
news:kvidnbsKz-pTskTZnZ2dnUVZ_oSdnZ2d@comcast.com...
> Pull one bolt from the bellhousing, take it to the hardware store. Get 4
> just like it, but 5 or so inches longer. When you get home, cut the heads
> off and taper the ends. Install the 4 rods you made when you take out the
> 4 lower bellhousing bolts. This will allow the trans to slide back free of
> the pilot bearing upon removal, and will make alignment for re-install
> VERY easy.
>
> HTH
>
> Carl
>
>
> "JimG" <JimG@nospam.com> wrote in message
> news:kaaCg.7179$oa1.1429@news02.roc.ny...
>> The tranny has locked up again in neutral... this time it ain't comin'
>> out. Any words of wisdom before I yank it out?
>> happened once before several months ago... but I jiggled, pounded, etc.
>> and it started working again. Stick shift goes left to right but wont go
>> in any gear.... engine off/on, clutch in/out, rock back and forth... all
>> that stuff. NV3550 my ars!#@*#
>> --
>> --
>> JimG
>> 80' CJ-7 258 CID, HEI
>> 4.56 Gears, Lock-Right F&R
>> 35" BFG MT on 15x10 Centerlines
>> D44 Rear, D30 Front. SOA
>> Dana 300 w/4:1 & Currie twin sticks
>> Warn X8000i w/ dual batteries
>>
>> 00' TJ Sport 4.0L, 5sp
>> 4.56 Gears, TrueTrac rear
>> 33" BFG AT on 15x8 Eagle Alloys
>> D35 Rear, D30 Front. 3" Suspension Lift
>> Warn X8000i
>>
>>
>
>

Re: TJ tranny locked up... again! Help!
 

Cool idea... Thanks! But I was hoping you would say something like... "turn
hat to left side, stick tongue out to right side, close one eye and pull
shifter back while standing on left foot only".


"Carl" <carlsaiyed@hotmailREMOVE.com> wrote in message
news:kvidnbsKz-pTskTZnZ2dnUVZ_oSdnZ2d@comcast.com...
> Pull one bolt from the bellhousing, take it to the hardware store. Get 4
> just like it, but 5 or so inches longer. When you get home, cut the heads
> off and taper the ends. Install the 4 rods you made when you take out the
> 4 lower bellhousing bolts. This will allow the trans to slide back free of
> the pilot bearing upon removal, and will make alignment for re-install
> VERY easy.
>
> HTH
>
> Carl
>
>
> "JimG" <JimG@nospam.com> wrote in message
> news:kaaCg.7179$oa1.1429@news02.roc.ny...
>> The tranny has locked up again in neutral... this time it ain't comin'
>> out. Any words of wisdom before I yank it out?
>> happened once before several months ago... but I jiggled, pounded, etc.
>> and it started working again. Stick shift goes left to right but wont go
>> in any gear.... engine off/on, clutch in/out, rock back and forth... all
>> that stuff. NV3550 my ars!#@*#
>> --
>> --
>> JimG
>> 80' CJ-7 258 CID, HEI
>> 4.56 Gears, Lock-Right F&R
>> 35" BFG MT on 15x10 Centerlines
>> D44 Rear, D30 Front. SOA
>> Dana 300 w/4:1 & Currie twin sticks
>> Warn X8000i w/ dual batteries
>>
>> 00' TJ Sport 4.0L, 5sp
>> 4.56 Gears, TrueTrac rear
>> 33" BFG AT on 15x8 Eagle Alloys
>> D35 Rear, D30 Front. 3" Suspension Lift
>> Warn X8000i
>>
>>
>
>

Re: TJ tranny locked up... again! Help!
 

Cool idea... Thanks! But I was hoping you would say something like... "turn
hat to left side, stick tongue out to right side, close one eye and pull
shifter back while standing on left foot only".


"Carl" <carlsaiyed@hotmailREMOVE.com> wrote in message
news:kvidnbsKz-pTskTZnZ2dnUVZ_oSdnZ2d@comcast.com...
> Pull one bolt from the bellhousing, take it to the hardware store. Get 4
> just like it, but 5 or so inches longer. When you get home, cut the heads
> off and taper the ends. Install the 4 rods you made when you take out the
> 4 lower bellhousing bolts. This will allow the trans to slide back free of
> the pilot bearing upon removal, and will make alignment for re-install
> VERY easy.
>
> HTH
>
> Carl
>
>
> "JimG" <JimG@nospam.com> wrote in message
> news:kaaCg.7179$oa1.1429@news02.roc.ny...
>> The tranny has locked up again in neutral... this time it ain't comin'
>> out. Any words of wisdom before I yank it out?
>> happened once before several months ago... but I jiggled, pounded, etc.
>> and it started working again. Stick shift goes left to right but wont go
>> in any gear.... engine off/on, clutch in/out, rock back and forth... all
>> that stuff. NV3550 my ars!#@*#
>> --
>> --
>> JimG
>> 80' CJ-7 258 CID, HEI
>> 4.56 Gears, Lock-Right F&R
>> 35" BFG MT on 15x10 Centerlines
>> D44 Rear, D30 Front. SOA
>> Dana 300 w/4:1 & Currie twin sticks
>> Warn X8000i w/ dual batteries
>>
>> 00' TJ Sport 4.0L, 5sp
>> 4.56 Gears, TrueTrac rear
>> 33" BFG AT on 15x8 Eagle Alloys
>> D35 Rear, D30 Front. 3" Suspension Lift
>> Warn X8000i
>>
>>
>
>

Re: TJ tranny locked up... again! Help!
 

Cool idea... Thanks! But I was hoping you would say something like... "turn
hat to left side, stick tongue out to right side, close one eye and pull
shifter back while standing on left foot only".


"Carl" <carlsaiyed@hotmailREMOVE.com> wrote in message
news:kvidnbsKz-pTskTZnZ2dnUVZ_oSdnZ2d@comcast.com...
> Pull one bolt from the bellhousing, take it to the hardware store. Get 4
> just like it, but 5 or so inches longer. When you get home, cut the heads
> off and taper the ends. Install the 4 rods you made when you take out the
> 4 lower bellhousing bolts. This will allow the trans to slide back free of
> the pilot bearing upon removal, and will make alignment for re-install
> VERY easy.
>
> HTH
>
> Carl
>
>
> "JimG" <JimG@nospam.com> wrote in message
> news:kaaCg.7179$oa1.1429@news02.roc.ny...
>> The tranny has locked up again in neutral... this time it ain't comin'
>> out. Any words of wisdom before I yank it out?
>> happened once before several months ago... but I jiggled, pounded, etc.
>> and it started working again. Stick shift goes left to right but wont go
>> in any gear.... engine off/on, clutch in/out, rock back and forth... all
>> that stuff. NV3550 my ars!#@*#
>> --
>> --
>> JimG
>> 80' CJ-7 258 CID, HEI
>> 4.56 Gears, Lock-Right F&R
>> 35" BFG MT on 15x10 Centerlines
>> D44 Rear, D30 Front. SOA
>> Dana 300 w/4:1 & Currie twin sticks
>> Warn X8000i w/ dual batteries
>>
>> 00' TJ Sport 4.0L, 5sp
>> 4.56 Gears, TrueTrac rear
>> 33" BFG AT on 15x8 Eagle Alloys
>> D35 Rear, D30 Front. 3" Suspension Lift
>> Warn X8000i
>>
>>
>
>

Re: TJ tranny locked up... again! Help!
 

add flat bladed cuts the the bolts after cutting heads so u can use a screw
driver to remove the studs u made

Carl wrote:

> Pull one bolt from the bellhousing, take it to the hardware store. Get 4
> just like it, but 5 or so inches longer. When you get home, cut the heads
> off and taper the ends. Install the 4 rods you made when you take out the 4
> lower bellhousing bolts. This will allow the trans to slide back free of the
> pilot bearing upon removal, and will make alignment for re-install VERY
> easy.
>
> HTH
>
> Carl
>
> "JimG" <JimG@nospam.com> wrote in message
> news:kaaCg.7179$oa1.1429@news02.roc.ny...
> > The tranny has locked up again in neutral... this time it ain't comin'
> > out. Any words of wisdom before I yank it out?
> > happened once before several months ago... but I jiggled, pounded, etc.
> > and it started working again. Stick shift goes left to right but wont go
> > in any gear.... engine off/on, clutch in/out, rock back and forth... all
> > that stuff. NV3550 my ars!#@*#
> > --
> > --
> > JimG
> > 80' CJ-7 258 CID, HEI
> > 4.56 Gears, Lock-Right F&R
> > 35" BFG MT on 15x10 Centerlines
> > D44 Rear, D30 Front. SOA
> > Dana 300 w/4:1 & Currie twin sticks
> > Warn X8000i w/ dual batteries
> >
> > 00' TJ Sport 4.0L, 5sp
> > 4.56 Gears, TrueTrac rear
> > 33" BFG AT on 15x8 Eagle Alloys
> > D35 Rear, D30 Front. 3" Suspension Lift
> > Warn X8000i
> >
> >