TJ Tailgate Hinge Bolt Removal
#31
Guest
Posts: n/a
Re: TJ Tailgate Hinge Bolt Removal
Thanks for the follow up. I am curious, do the back hinge bolts on the
TJ use that thread sealer like the windshield and door ones on the older
Jeeps use? Could save someone some paint maybe some day...
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
Keith Orbell wrote:
>
> Thanks Earle.
>
> I actually managed to get one bolt undone, from that I was then able to get
> its' pair free by moving the nut plate behind the body.
>
> These certainly look like the thing to try for the bolts of the other hinge.
>
> (I already heard about these so-called "Easy Out"s.. tempting as they seem!)
>
> Keith
>
> "Earle Horton" <NurseBustersNoSpam@msn.com> wrote in message
> news:44540125$0$24428$a82e2bb9@reader.athenanews.c om...
> > Machine shop where I used to have busted off studs removed used left
> > handed
> > drill bits. They told me sometimes the bit would grab onto the stud and
> > pull it right out. They are also good for practical jokes. These look
> > like
> > a reasonable deal.
> >
> > http://www.shopsbs.com/store/product...roducts_id=152
> >
> > One thing that you absolutely do not want to use, on any busted off stud
> > or
> > stripped bolt, is an "Easy Out", especially the spiral ones. Unless you
> > want to swell up the thing you want to remove, and then break off a piece
> > of
> > hardened metal in it.
> >
> > Earle
> >
> > "Mike Romain" <romainm@sympatico.ca> wrote in message
> > news:445377C5.65D9810A@sympatico.ca...
> >> From my experience with those torx suckers, the triple coating of paint
> >> inside them (under coat, color, clear coat) means you cannot fit the
> >> correct bit into it. So you have a tight fitting, one size too small,
> >> of a bit, then you apply torque and the paint layers crush and the bit
> >> reams out the screw faster than you can blink.
> >>
> >> I have also found that Jeep used a thread sealer on most body bolts that
> >> requires a torch to de-activate.
> >>
> >> I have only had success using a torch first to really heat the bolt and
> >> burn or peel the now soft paint out so the bit fits properly, then it
> >> will slowly turn out likely needing torque all the way.
> >>
> >> I expect to have to paint the hinge after and try not to tag the body
> >> paint with the torch.
> >>
> >> Then when I have to drill one out, I use a bit about 2/3 the size of the
> >> bolt and aim it slightly to one edge so I 'just' tag the threads. This
> >> leaves the bolt looking like a hollow 3/4 moon shape that always has
> >> been able to back out fairly easily and the hole will still hold a new
> >> bolt.
> >>
> >> Mike
> >> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> >> 88 Cherokee 235 BFG AT's
> >> Canadian Off Road Trips Photos: Non members can still view!
> >> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> >> (More Off Road album links at bottom of the view page)
> >>
> >> Keith Orbell wrote:
> >> >
> >> > Can anyone offer some advice on what the best way to get the hinge
> >> > bolts
> > out
> >> > is ?
> >> >
> >> > I have a T40 socket which seemed to be better at grinding the head
> > rather
> >> > than actually turning one of the bolts. I gave the whole lot a soak in
> > PB
> >> > blaster last night but other than that is there anything I can do other
> > than
> >> > get the bolts drilled out ?
> >> >
> >> > Thanks
> >> > Keith
> >
> >
TJ use that thread sealer like the windshield and door ones on the older
Jeeps use? Could save someone some paint maybe some day...
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
Keith Orbell wrote:
>
> Thanks Earle.
>
> I actually managed to get one bolt undone, from that I was then able to get
> its' pair free by moving the nut plate behind the body.
>
> These certainly look like the thing to try for the bolts of the other hinge.
>
> (I already heard about these so-called "Easy Out"s.. tempting as they seem!)
>
> Keith
>
> "Earle Horton" <NurseBustersNoSpam@msn.com> wrote in message
> news:44540125$0$24428$a82e2bb9@reader.athenanews.c om...
> > Machine shop where I used to have busted off studs removed used left
> > handed
> > drill bits. They told me sometimes the bit would grab onto the stud and
> > pull it right out. They are also good for practical jokes. These look
> > like
> > a reasonable deal.
> >
> > http://www.shopsbs.com/store/product...roducts_id=152
> >
> > One thing that you absolutely do not want to use, on any busted off stud
> > or
> > stripped bolt, is an "Easy Out", especially the spiral ones. Unless you
> > want to swell up the thing you want to remove, and then break off a piece
> > of
> > hardened metal in it.
> >
> > Earle
> >
> > "Mike Romain" <romainm@sympatico.ca> wrote in message
> > news:445377C5.65D9810A@sympatico.ca...
> >> From my experience with those torx suckers, the triple coating of paint
> >> inside them (under coat, color, clear coat) means you cannot fit the
> >> correct bit into it. So you have a tight fitting, one size too small,
> >> of a bit, then you apply torque and the paint layers crush and the bit
> >> reams out the screw faster than you can blink.
> >>
> >> I have also found that Jeep used a thread sealer on most body bolts that
> >> requires a torch to de-activate.
> >>
> >> I have only had success using a torch first to really heat the bolt and
> >> burn or peel the now soft paint out so the bit fits properly, then it
> >> will slowly turn out likely needing torque all the way.
> >>
> >> I expect to have to paint the hinge after and try not to tag the body
> >> paint with the torch.
> >>
> >> Then when I have to drill one out, I use a bit about 2/3 the size of the
> >> bolt and aim it slightly to one edge so I 'just' tag the threads. This
> >> leaves the bolt looking like a hollow 3/4 moon shape that always has
> >> been able to back out fairly easily and the hole will still hold a new
> >> bolt.
> >>
> >> Mike
> >> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> >> 88 Cherokee 235 BFG AT's
> >> Canadian Off Road Trips Photos: Non members can still view!
> >> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> >> (More Off Road album links at bottom of the view page)
> >>
> >> Keith Orbell wrote:
> >> >
> >> > Can anyone offer some advice on what the best way to get the hinge
> >> > bolts
> > out
> >> > is ?
> >> >
> >> > I have a T40 socket which seemed to be better at grinding the head
> > rather
> >> > than actually turning one of the bolts. I gave the whole lot a soak in
> > PB
> >> > blaster last night but other than that is there anything I can do other
> > than
> >> > get the bolts drilled out ?
> >> >
> >> > Thanks
> >> > Keith
> >
> >
#32
Guest
Posts: n/a
Re: TJ Tailgate Hinge Bolt Removal
Hi Earl,
If you're good, you can blow it out even needing a thread chaser.
Pop it with a damp rag, shrink it and not need touch up.
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
Earle Horton wrote:
>
> In case anyone is taking this little side thread seriously, I would advise
> against it. Heating steel in the presence of oxygen can cause metallurgical
> changes that render it unsuitable for its original purpose. The usual
> result of blasting out a stud with oxygen, is hardening of the metal in the
> vicinity of the hole, so that taps and drill bits just break off in it.
>
> Earle
If you're good, you can blow it out even needing a thread chaser.
Pop it with a damp rag, shrink it and not need touch up.
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
Earle Horton wrote:
>
> In case anyone is taking this little side thread seriously, I would advise
> against it. Heating steel in the presence of oxygen can cause metallurgical
> changes that render it unsuitable for its original purpose. The usual
> result of blasting out a stud with oxygen, is hardening of the metal in the
> vicinity of the hole, so that taps and drill bits just break off in it.
>
> Earle
#33
Guest
Posts: n/a
Re: TJ Tailgate Hinge Bolt Removal
Hi Earl,
If you're good, you can blow it out even needing a thread chaser.
Pop it with a damp rag, shrink it and not need touch up.
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
Earle Horton wrote:
>
> In case anyone is taking this little side thread seriously, I would advise
> against it. Heating steel in the presence of oxygen can cause metallurgical
> changes that render it unsuitable for its original purpose. The usual
> result of blasting out a stud with oxygen, is hardening of the metal in the
> vicinity of the hole, so that taps and drill bits just break off in it.
>
> Earle
If you're good, you can blow it out even needing a thread chaser.
Pop it with a damp rag, shrink it and not need touch up.
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
Earle Horton wrote:
>
> In case anyone is taking this little side thread seriously, I would advise
> against it. Heating steel in the presence of oxygen can cause metallurgical
> changes that render it unsuitable for its original purpose. The usual
> result of blasting out a stud with oxygen, is hardening of the metal in the
> vicinity of the hole, so that taps and drill bits just break off in it.
>
> Earle
#34
Guest
Posts: n/a
Re: TJ Tailgate Hinge Bolt Removal
Hi Earl,
If you're good, you can blow it out even needing a thread chaser.
Pop it with a damp rag, shrink it and not need touch up.
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
Earle Horton wrote:
>
> In case anyone is taking this little side thread seriously, I would advise
> against it. Heating steel in the presence of oxygen can cause metallurgical
> changes that render it unsuitable for its original purpose. The usual
> result of blasting out a stud with oxygen, is hardening of the metal in the
> vicinity of the hole, so that taps and drill bits just break off in it.
>
> Earle
If you're good, you can blow it out even needing a thread chaser.
Pop it with a damp rag, shrink it and not need touch up.
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
Earle Horton wrote:
>
> In case anyone is taking this little side thread seriously, I would advise
> against it. Heating steel in the presence of oxygen can cause metallurgical
> changes that render it unsuitable for its original purpose. The usual
> result of blasting out a stud with oxygen, is hardening of the metal in the
> vicinity of the hole, so that taps and drill bits just break off in it.
>
> Earle
#35
Guest
Posts: n/a
Re: TJ Tailgate Hinge Bolt Removal
On Sun, 30 Apr 2006 17:38:09 -0700, "L.W.(Bill) ------ III"
<----------@***.net> wrote:
>>My Goat's ---- is hard, what should I do?
> If you're good, you can blow it out even needing a thread chaser.
You're such a pervert, Goat ----er.
--
Just your average Joe.
<----------@***.net> wrote:
>>My Goat's ---- is hard, what should I do?
> If you're good, you can blow it out even needing a thread chaser.
You're such a pervert, Goat ----er.
--
Just your average Joe.
#36
Guest
Posts: n/a
Re: TJ Tailgate Hinge Bolt Removal
On Sun, 30 Apr 2006 17:38:09 -0700, "L.W.(Bill) ------ III"
<----------@***.net> wrote:
>>My Goat's ---- is hard, what should I do?
> If you're good, you can blow it out even needing a thread chaser.
You're such a pervert, Goat ----er.
--
Just your average Joe.
<----------@***.net> wrote:
>>My Goat's ---- is hard, what should I do?
> If you're good, you can blow it out even needing a thread chaser.
You're such a pervert, Goat ----er.
--
Just your average Joe.
#37
Guest
Posts: n/a
Re: TJ Tailgate Hinge Bolt Removal
On Sun, 30 Apr 2006 17:38:09 -0700, "L.W.(Bill) ------ III"
<----------@***.net> wrote:
>>My Goat's ---- is hard, what should I do?
> If you're good, you can blow it out even needing a thread chaser.
You're such a pervert, Goat ----er.
--
Just your average Joe.
<----------@***.net> wrote:
>>My Goat's ---- is hard, what should I do?
> If you're good, you can blow it out even needing a thread chaser.
You're such a pervert, Goat ----er.
--
Just your average Joe.
Thread
Thread Starter
Forum
Replies
Last Post
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)