Re: Tie Rod Issues and replacement
Will Honea wrote:
> If you have an inmpact wrench, you can usually get those @#$% nuts > started by pushing the socket on so that it holds the rod fairly solid > then bash the ball joint from the other side as you run the air. That > will drive the taper in far enough to grab for a bit - might even hold > to get it all the way off. When all else fails, you can usually cut > the grease boot out of the way and get a pipe wrench or big pair of > vice ripes on the lower part of the ball and/or the stem. Worst comes > to worst, just drive the pickle fork in like you were pulling the > thing out - that will usually hold them still as well - but you have > to keep driving it tight as you go. at that point I'd probably drag out a nut-splitter or the cutoff wheel. -- DougW |
Re: Tie Rod Issues and replacement
Central Illinois.
On 9/18/06 9:31 PM, in article RcmdnRyakuUuy5LYnZ2dnUVZ_r-dnZ2d@comcast.com, "Carl" <carlsaiyed@hotmailREMOVE.com> wrote: > Where are you located? > > Carl > > "Les" <nospam@nospam.com> wrote in message > news:C1347A3E.8F10%nospam@nospam.com... >> Oops wrong part. It's $143, ouch. Some sites have this listed as a Drag >> link, while others list it as a tie rod.. Aaargh. >> >> >> >> On 9/18/06 4:23 PM, in article C134788D.8F08%nospam@nospam.com, "Les" >> <nospam@nospam.com> wrote: >> >>> Wow the OEM price ($45) is less than Napa or Autozone. That's rare. >>> >>> >>> >>> >>> On 9/18/06 3:51 PM, in article aFDPg.13224$JR5.6201@dukeread11, "DougW" >>> <post.replies@invalid.address> wrote: >>> >>>> Les wrote: >>>>> Just verified that XJ, ZJ, TJ tie rods are not the same type and >>>>> won't work. Guess I'll have to shell out the $100 for the new one. >>>> >>>> check with napaonline.com but only go with the NCP (napa chassis parts) >>>> line as the other cheaper line isn't that good. >>>> >>>> for OEM I deal with http://www.chryslerpartsdirect.com/ >>>> >>>> Just finished replacing the inner right joint (drag link to tie bar). >>> >> > > |
Re: Tie Rod Issues and replacement
Central Illinois.
On 9/18/06 9:31 PM, in article RcmdnRyakuUuy5LYnZ2dnUVZ_r-dnZ2d@comcast.com, "Carl" <carlsaiyed@hotmailREMOVE.com> wrote: > Where are you located? > > Carl > > "Les" <nospam@nospam.com> wrote in message > news:C1347A3E.8F10%nospam@nospam.com... >> Oops wrong part. It's $143, ouch. Some sites have this listed as a Drag >> link, while others list it as a tie rod.. Aaargh. >> >> >> >> On 9/18/06 4:23 PM, in article C134788D.8F08%nospam@nospam.com, "Les" >> <nospam@nospam.com> wrote: >> >>> Wow the OEM price ($45) is less than Napa or Autozone. That's rare. >>> >>> >>> >>> >>> On 9/18/06 3:51 PM, in article aFDPg.13224$JR5.6201@dukeread11, "DougW" >>> <post.replies@invalid.address> wrote: >>> >>>> Les wrote: >>>>> Just verified that XJ, ZJ, TJ tie rods are not the same type and >>>>> won't work. Guess I'll have to shell out the $100 for the new one. >>>> >>>> check with napaonline.com but only go with the NCP (napa chassis parts) >>>> line as the other cheaper line isn't that good. >>>> >>>> for OEM I deal with http://www.chryslerpartsdirect.com/ >>>> >>>> Just finished replacing the inner right joint (drag link to tie bar). >>> >> > > |
Re: Tie Rod Issues and replacement
Central Illinois.
On 9/18/06 9:31 PM, in article RcmdnRyakuUuy5LYnZ2dnUVZ_r-dnZ2d@comcast.com, "Carl" <carlsaiyed@hotmailREMOVE.com> wrote: > Where are you located? > > Carl > > "Les" <nospam@nospam.com> wrote in message > news:C1347A3E.8F10%nospam@nospam.com... >> Oops wrong part. It's $143, ouch. Some sites have this listed as a Drag >> link, while others list it as a tie rod.. Aaargh. >> >> >> >> On 9/18/06 4:23 PM, in article C134788D.8F08%nospam@nospam.com, "Les" >> <nospam@nospam.com> wrote: >> >>> Wow the OEM price ($45) is less than Napa or Autozone. That's rare. >>> >>> >>> >>> >>> On 9/18/06 3:51 PM, in article aFDPg.13224$JR5.6201@dukeread11, "DougW" >>> <post.replies@invalid.address> wrote: >>> >>>> Les wrote: >>>>> Just verified that XJ, ZJ, TJ tie rods are not the same type and >>>>> won't work. Guess I'll have to shell out the $100 for the new one. >>>> >>>> check with napaonline.com but only go with the NCP (napa chassis parts) >>>> line as the other cheaper line isn't that good. >>>> >>>> for OEM I deal with http://www.chryslerpartsdirect.com/ >>>> >>>> Just finished replacing the inner right joint (drag link to tie bar). >>> >> > > |
Re: Tie Rod Issues and replacement
I'm in the process of rounding up a nut splitter.
On 9/19/06 6:18 AM, in article tmQPg.13247$JR5.7209@dukeread11, "DougW" <post.replies@invalid.address> wrote: > > at that point I'd probably drag out a nut-splitter or the cutoff wheel. |
Re: Tie Rod Issues and replacement
I'm in the process of rounding up a nut splitter.
On 9/19/06 6:18 AM, in article tmQPg.13247$JR5.7209@dukeread11, "DougW" <post.replies@invalid.address> wrote: > > at that point I'd probably drag out a nut-splitter or the cutoff wheel. |
Re: Tie Rod Issues and replacement
I'm in the process of rounding up a nut splitter.
On 9/19/06 6:18 AM, in article tmQPg.13247$JR5.7209@dukeread11, "DougW" <post.replies@invalid.address> wrote: > > at that point I'd probably drag out a nut-splitter or the cutoff wheel. |
Re: Tie Rod Issues and replacement
Just found a complete used, but decent replacement for $20 from a guy in a
local Jeep Club. Cool. On 9/19/06 8:01 AM, in article C1355467.8F49%nospam@nospam.com, "Les" <nospam@nospam.com> wrote: > I'm in the process of rounding up a nut splitter. > > > On 9/19/06 6:18 AM, in article tmQPg.13247$JR5.7209@dukeread11, "DougW" > <post.replies@invalid.address> wrote: > > >> >> at that point I'd probably drag out a nut-splitter or the cutoff wheel. > |
Re: Tie Rod Issues and replacement
Just found a complete used, but decent replacement for $20 from a guy in a
local Jeep Club. Cool. On 9/19/06 8:01 AM, in article C1355467.8F49%nospam@nospam.com, "Les" <nospam@nospam.com> wrote: > I'm in the process of rounding up a nut splitter. > > > On 9/19/06 6:18 AM, in article tmQPg.13247$JR5.7209@dukeread11, "DougW" > <post.replies@invalid.address> wrote: > > >> >> at that point I'd probably drag out a nut-splitter or the cutoff wheel. > |
Re: Tie Rod Issues and replacement
Just found a complete used, but decent replacement for $20 from a guy in a
local Jeep Club. Cool. On 9/19/06 8:01 AM, in article C1355467.8F49%nospam@nospam.com, "Les" <nospam@nospam.com> wrote: > I'm in the process of rounding up a nut splitter. > > > On 9/19/06 6:18 AM, in article tmQPg.13247$JR5.7209@dukeread11, "DougW" > <post.replies@invalid.address> wrote: > > >> >> at that point I'd probably drag out a nut-splitter or the cutoff wheel. > |
All times are GMT -4. The time now is 08:57 AM. |
© 2024 MH Sub I, LLC dba Internet Brands