Tie Rod Issues and replacement
92 YJ stock front axle and steering:
I've got a severely loose Passenger side Tie Rod end. Looks to me like the ball joint itself is not replaceable and the passenger side doesn't have a threaded end, so it looks like I'll have to replace the entire tie rod. I though I'd look for one at a junkyard rather than getting a new one and was wandering if XJ or ZJ etc. would also fit. Upgrading the steering is not really a concern as I just want to get it road worthy as cheap as possible so I can sell it. Also is there a trick to getting these things off without cutting them off. When I try to turn the castle nut off, the bolt and entire ball stud just spins with it. Are they supposed to do that. I tries to push it back up into the spindle arm, but it doesnąt want to seat I think the taper on the ball stud is worn down or something. |
Re: Tie Rod Issues and replacement
Squeeze the stud into the spindle arm using big Channel-Locking pliers, a
vice grip, a hydraulic jack or whatever seems to work. This may lock the stud into the socket enough so you can get the nut off. After spending a couple hours at that, cutting the stud won't seem like such a bad idea. ;^) Earle "Les" <nospam@nospam.com> wrote in message news:C13458DA.8AAD%nospam@nospam.com... > 92 YJ stock front axle and steering: > > I've got a severely loose Passenger side Tie Rod end. Looks to me like the > ball joint itself is not replaceable and the passenger side doesn't have a > threaded end, so it looks like I'll have to replace the entire tie rod. I > though I'd look for one at a junkyard rather than getting a new one and was > wandering if XJ or ZJ etc. would also fit. > > Upgrading the steering is not really a concern as I just want to get it road > worthy as cheap as possible so I can sell it. > > Also is there a trick to getting these things off without cutting them off. > When I try to turn the castle nut off, the bolt and entire ball stud just > spins with it. Are they supposed to do that. I tries to push it back up into > the spindle arm, but it doesnąt want to seat I think the taper on the ball > stud is worn down or something. > |
Re: Tie Rod Issues and replacement
Squeeze the stud into the spindle arm using big Channel-Locking pliers, a
vice grip, a hydraulic jack or whatever seems to work. This may lock the stud into the socket enough so you can get the nut off. After spending a couple hours at that, cutting the stud won't seem like such a bad idea. ;^) Earle "Les" <nospam@nospam.com> wrote in message news:C13458DA.8AAD%nospam@nospam.com... > 92 YJ stock front axle and steering: > > I've got a severely loose Passenger side Tie Rod end. Looks to me like the > ball joint itself is not replaceable and the passenger side doesn't have a > threaded end, so it looks like I'll have to replace the entire tie rod. I > though I'd look for one at a junkyard rather than getting a new one and was > wandering if XJ or ZJ etc. would also fit. > > Upgrading the steering is not really a concern as I just want to get it road > worthy as cheap as possible so I can sell it. > > Also is there a trick to getting these things off without cutting them off. > When I try to turn the castle nut off, the bolt and entire ball stud just > spins with it. Are they supposed to do that. I tries to push it back up into > the spindle arm, but it doesnąt want to seat I think the taper on the ball > stud is worn down or something. > |
Re: Tie Rod Issues and replacement
Squeeze the stud into the spindle arm using big Channel-Locking pliers, a
vice grip, a hydraulic jack or whatever seems to work. This may lock the stud into the socket enough so you can get the nut off. After spending a couple hours at that, cutting the stud won't seem like such a bad idea. ;^) Earle "Les" <nospam@nospam.com> wrote in message news:C13458DA.8AAD%nospam@nospam.com... > 92 YJ stock front axle and steering: > > I've got a severely loose Passenger side Tie Rod end. Looks to me like the > ball joint itself is not replaceable and the passenger side doesn't have a > threaded end, so it looks like I'll have to replace the entire tie rod. I > though I'd look for one at a junkyard rather than getting a new one and was > wandering if XJ or ZJ etc. would also fit. > > Upgrading the steering is not really a concern as I just want to get it road > worthy as cheap as possible so I can sell it. > > Also is there a trick to getting these things off without cutting them off. > When I try to turn the castle nut off, the bolt and entire ball stud just > spins with it. Are they supposed to do that. I tries to push it back up into > the spindle arm, but it doesnąt want to seat I think the taper on the ball > stud is worn down or something. > |
Re: Tie Rod Issues and replacement
To start you are posting in html and this is a text only group. Lots of
folks don't use microcrap and your post isn't readable. Lots of servers cut them so they don't even make it or just the header with no body shows. Meanwhile, you sound like you are talking about the drag link ball joint that goes to the passenger wheel side from the steering. That is one piece. If the taper is gone, it can be an expensive fix to replace the whole steering knuckle or get a machine shop to fill and cut you a new taper in the hole once you get it off. I have a pair of needle nose vise grips I use for spinning ones. I get them between the ball and the knuckle arm on the bottom side and pray or cuss. I also soak the crap out of the castle nut with penetrating oil. I still have to cut off 'Way' too many of them..... The good news is it doesn't affect the front end alignment, only the steering wheel adjustment. The sleeve at the top end turns to adjust the angle of the steering wheel, so it is wise or just easier to mark it or measure it. It can be a bit of a pain getting the wheel back straight. If it isn't straight now, now's the time to fix it. ;-) Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Canadian Off Road Trips Photos: Non members can still view! Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 (More Off Road album links at bottom of the view page) |
Re: Tie Rod Issues and replacement
To start you are posting in html and this is a text only group. Lots of
folks don't use microcrap and your post isn't readable. Lots of servers cut them so they don't even make it or just the header with no body shows. Meanwhile, you sound like you are talking about the drag link ball joint that goes to the passenger wheel side from the steering. That is one piece. If the taper is gone, it can be an expensive fix to replace the whole steering knuckle or get a machine shop to fill and cut you a new taper in the hole once you get it off. I have a pair of needle nose vise grips I use for spinning ones. I get them between the ball and the knuckle arm on the bottom side and pray or cuss. I also soak the crap out of the castle nut with penetrating oil. I still have to cut off 'Way' too many of them..... The good news is it doesn't affect the front end alignment, only the steering wheel adjustment. The sleeve at the top end turns to adjust the angle of the steering wheel, so it is wise or just easier to mark it or measure it. It can be a bit of a pain getting the wheel back straight. If it isn't straight now, now's the time to fix it. ;-) Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Canadian Off Road Trips Photos: Non members can still view! Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 (More Off Road album links at bottom of the view page) |
Re: Tie Rod Issues and replacement
To start you are posting in html and this is a text only group. Lots of
folks don't use microcrap and your post isn't readable. Lots of servers cut them so they don't even make it or just the header with no body shows. Meanwhile, you sound like you are talking about the drag link ball joint that goes to the passenger wheel side from the steering. That is one piece. If the taper is gone, it can be an expensive fix to replace the whole steering knuckle or get a machine shop to fill and cut you a new taper in the hole once you get it off. I have a pair of needle nose vise grips I use for spinning ones. I get them between the ball and the knuckle arm on the bottom side and pray or cuss. I also soak the crap out of the castle nut with penetrating oil. I still have to cut off 'Way' too many of them..... The good news is it doesn't affect the front end alignment, only the steering wheel adjustment. The sleeve at the top end turns to adjust the angle of the steering wheel, so it is wise or just easier to mark it or measure it. It can be a bit of a pain getting the wheel back straight. If it isn't straight now, now's the time to fix it. ;-) Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Canadian Off Road Trips Photos: Non members can still view! Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 (More Off Road album links at bottom of the view page) |
Re: Tie Rod Issues and replacement
Sorry about the HTML, did that fix it? At least you guys don't seem to mind
top posting. That really gets some groups in a bender! Ya, that's the piece I'm talking about. The long one that's parallel to the axle and connects to the pass side spindle. Parts store was calling it an outer tie rod end. As far as the replacement parts, do any of you know if XJ, ZJ, or any other jeep models are compatible? I'd rather find a decent one at the salvage yard, that pay the parts store $125 for a replacement. Also I have a feeling that when I take this one off, I'll end up having to cut off the "inner" tie rod links also. They are just a rusty as this one, and I imagine they'll all be spinners too. Thanks in advance for all your replies. -Les On 9/18/06 2:57 PM, in article 450EFA13.66E55181@sympatico.ca, "Mike Romain" <romainm@sympatico.ca> wrote: > To start you are posting in html and this is a text only group. Lots of > folks don't use microcrap and your post isn't readable. Lots of servers > cut them so they don't even make it or just the header with no body > shows. > > Meanwhile, you sound like you are talking about the drag link ball joint > that goes to the passenger wheel side from the steering. That is one > piece. > > If the taper is gone, it can be an expensive fix to replace the whole > steering knuckle or get a machine shop to fill and cut you a new taper > in the hole once you get it off. > > I have a pair of needle nose vise grips I use for spinning ones. I get > them between the ball and the knuckle arm on the bottom side and pray or > cuss. I also soak the crap out of the castle nut with penetrating oil. > > I still have to cut off 'Way' too many of them..... > > The good news is it doesn't affect the front end alignment, only the > steering wheel adjustment. The sleeve at the top end turns to adjust > the angle of the steering wheel, so it is wise or just easier to mark it > or measure it. It can be a bit of a pain getting the wheel back > straight. If it isn't straight now, now's the time to fix it. ;-) > > Mike > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > 88 Cherokee 235 BFG AT's > Canadian Off Road Trips Photos: Non members can still view! > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 > (More Off Road album links at bottom of the view page) |
Re: Tie Rod Issues and replacement
Sorry about the HTML, did that fix it? At least you guys don't seem to mind
top posting. That really gets some groups in a bender! Ya, that's the piece I'm talking about. The long one that's parallel to the axle and connects to the pass side spindle. Parts store was calling it an outer tie rod end. As far as the replacement parts, do any of you know if XJ, ZJ, or any other jeep models are compatible? I'd rather find a decent one at the salvage yard, that pay the parts store $125 for a replacement. Also I have a feeling that when I take this one off, I'll end up having to cut off the "inner" tie rod links also. They are just a rusty as this one, and I imagine they'll all be spinners too. Thanks in advance for all your replies. -Les On 9/18/06 2:57 PM, in article 450EFA13.66E55181@sympatico.ca, "Mike Romain" <romainm@sympatico.ca> wrote: > To start you are posting in html and this is a text only group. Lots of > folks don't use microcrap and your post isn't readable. Lots of servers > cut them so they don't even make it or just the header with no body > shows. > > Meanwhile, you sound like you are talking about the drag link ball joint > that goes to the passenger wheel side from the steering. That is one > piece. > > If the taper is gone, it can be an expensive fix to replace the whole > steering knuckle or get a machine shop to fill and cut you a new taper > in the hole once you get it off. > > I have a pair of needle nose vise grips I use for spinning ones. I get > them between the ball and the knuckle arm on the bottom side and pray or > cuss. I also soak the crap out of the castle nut with penetrating oil. > > I still have to cut off 'Way' too many of them..... > > The good news is it doesn't affect the front end alignment, only the > steering wheel adjustment. The sleeve at the top end turns to adjust > the angle of the steering wheel, so it is wise or just easier to mark it > or measure it. It can be a bit of a pain getting the wheel back > straight. If it isn't straight now, now's the time to fix it. ;-) > > Mike > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > 88 Cherokee 235 BFG AT's > Canadian Off Road Trips Photos: Non members can still view! > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 > (More Off Road album links at bottom of the view page) |
Re: Tie Rod Issues and replacement
Sorry about the HTML, did that fix it? At least you guys don't seem to mind
top posting. That really gets some groups in a bender! Ya, that's the piece I'm talking about. The long one that's parallel to the axle and connects to the pass side spindle. Parts store was calling it an outer tie rod end. As far as the replacement parts, do any of you know if XJ, ZJ, or any other jeep models are compatible? I'd rather find a decent one at the salvage yard, that pay the parts store $125 for a replacement. Also I have a feeling that when I take this one off, I'll end up having to cut off the "inner" tie rod links also. They are just a rusty as this one, and I imagine they'll all be spinners too. Thanks in advance for all your replies. -Les On 9/18/06 2:57 PM, in article 450EFA13.66E55181@sympatico.ca, "Mike Romain" <romainm@sympatico.ca> wrote: > To start you are posting in html and this is a text only group. Lots of > folks don't use microcrap and your post isn't readable. Lots of servers > cut them so they don't even make it or just the header with no body > shows. > > Meanwhile, you sound like you are talking about the drag link ball joint > that goes to the passenger wheel side from the steering. That is one > piece. > > If the taper is gone, it can be an expensive fix to replace the whole > steering knuckle or get a machine shop to fill and cut you a new taper > in the hole once you get it off. > > I have a pair of needle nose vise grips I use for spinning ones. I get > them between the ball and the knuckle arm on the bottom side and pray or > cuss. I also soak the crap out of the castle nut with penetrating oil. > > I still have to cut off 'Way' too many of them..... > > The good news is it doesn't affect the front end alignment, only the > steering wheel adjustment. The sleeve at the top end turns to adjust > the angle of the steering wheel, so it is wise or just easier to mark it > or measure it. It can be a bit of a pain getting the wheel back > straight. If it isn't straight now, now's the time to fix it. ;-) > > Mike > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > 88 Cherokee 235 BFG AT's > Canadian Off Road Trips Photos: Non members can still view! > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 > (More Off Road album links at bottom of the view page) |
Re: Tie Rod Issues and replacement
Just verified that XJ, ZJ, TJ tie rods are not the same type and won't work.
Guess I'll have to shell out the $100 for the new one. On 9/18/06 3:11 PM, in article C13467B9.8E37%nospam@nospam.com, "Les" <nospam@nospam.com> wrote: > Sorry about the HTML, did that fix it? At least you guys don't seem to mind > top posting. That really gets some groups in a bender! > > Ya, that's the piece I'm talking about. The long one that's parallel to the > axle and connects to the pass side spindle. Parts store was calling it an > outer tie rod end. > > As far as the replacement parts, do any of you know if XJ, ZJ, or any other > jeep models are compatible? I'd rather find a decent one at the salvage > yard, that pay the parts store $125 for a replacement. > > Also I have a feeling that when I take this one off, I'll end up having to > cut off the "inner" tie rod links also. They are just a rusty as this one, > and I imagine they'll all be spinners too. > > Thanks in advance for all your replies. > > -Les > > > > > On 9/18/06 2:57 PM, in article 450EFA13.66E55181@sympatico.ca, "Mike Romain" > <romainm@sympatico.ca> wrote: > >> To start you are posting in html and this is a text only group. Lots of >> folks don't use microcrap and your post isn't readable. Lots of servers >> cut them so they don't even make it or just the header with no body >> shows. >> >> Meanwhile, you sound like you are talking about the drag link ball joint >> that goes to the passenger wheel side from the steering. That is one >> piece. >> >> If the taper is gone, it can be an expensive fix to replace the whole >> steering knuckle or get a machine shop to fill and cut you a new taper >> in the hole once you get it off. >> >> I have a pair of needle nose vise grips I use for spinning ones. I get >> them between the ball and the knuckle arm on the bottom side and pray or >> cuss. I also soak the crap out of the castle nut with penetrating oil. >> >> I still have to cut off 'Way' too many of them..... >> >> The good news is it doesn't affect the front end alignment, only the >> steering wheel adjustment. The sleeve at the top end turns to adjust >> the angle of the steering wheel, so it is wise or just easier to mark it >> or measure it. It can be a bit of a pain getting the wheel back >> straight. If it isn't straight now, now's the time to fix it. ;-) >> >> Mike >> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 >> 88 Cherokee 235 BFG AT's >> Canadian Off Road Trips Photos: Non members can still view! >> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 >> (More Off Road album links at bottom of the view page) > |
Re: Tie Rod Issues and replacement
Just verified that XJ, ZJ, TJ tie rods are not the same type and won't work.
Guess I'll have to shell out the $100 for the new one. On 9/18/06 3:11 PM, in article C13467B9.8E37%nospam@nospam.com, "Les" <nospam@nospam.com> wrote: > Sorry about the HTML, did that fix it? At least you guys don't seem to mind > top posting. That really gets some groups in a bender! > > Ya, that's the piece I'm talking about. The long one that's parallel to the > axle and connects to the pass side spindle. Parts store was calling it an > outer tie rod end. > > As far as the replacement parts, do any of you know if XJ, ZJ, or any other > jeep models are compatible? I'd rather find a decent one at the salvage > yard, that pay the parts store $125 for a replacement. > > Also I have a feeling that when I take this one off, I'll end up having to > cut off the "inner" tie rod links also. They are just a rusty as this one, > and I imagine they'll all be spinners too. > > Thanks in advance for all your replies. > > -Les > > > > > On 9/18/06 2:57 PM, in article 450EFA13.66E55181@sympatico.ca, "Mike Romain" > <romainm@sympatico.ca> wrote: > >> To start you are posting in html and this is a text only group. Lots of >> folks don't use microcrap and your post isn't readable. Lots of servers >> cut them so they don't even make it or just the header with no body >> shows. >> >> Meanwhile, you sound like you are talking about the drag link ball joint >> that goes to the passenger wheel side from the steering. That is one >> piece. >> >> If the taper is gone, it can be an expensive fix to replace the whole >> steering knuckle or get a machine shop to fill and cut you a new taper >> in the hole once you get it off. >> >> I have a pair of needle nose vise grips I use for spinning ones. I get >> them between the ball and the knuckle arm on the bottom side and pray or >> cuss. I also soak the crap out of the castle nut with penetrating oil. >> >> I still have to cut off 'Way' too many of them..... >> >> The good news is it doesn't affect the front end alignment, only the >> steering wheel adjustment. The sleeve at the top end turns to adjust >> the angle of the steering wheel, so it is wise or just easier to mark it >> or measure it. It can be a bit of a pain getting the wheel back >> straight. If it isn't straight now, now's the time to fix it. ;-) >> >> Mike >> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 >> 88 Cherokee 235 BFG AT's >> Canadian Off Road Trips Photos: Non members can still view! >> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 >> (More Off Road album links at bottom of the view page) > |
Re: Tie Rod Issues and replacement
Just verified that XJ, ZJ, TJ tie rods are not the same type and won't work.
Guess I'll have to shell out the $100 for the new one. On 9/18/06 3:11 PM, in article C13467B9.8E37%nospam@nospam.com, "Les" <nospam@nospam.com> wrote: > Sorry about the HTML, did that fix it? At least you guys don't seem to mind > top posting. That really gets some groups in a bender! > > Ya, that's the piece I'm talking about. The long one that's parallel to the > axle and connects to the pass side spindle. Parts store was calling it an > outer tie rod end. > > As far as the replacement parts, do any of you know if XJ, ZJ, or any other > jeep models are compatible? I'd rather find a decent one at the salvage > yard, that pay the parts store $125 for a replacement. > > Also I have a feeling that when I take this one off, I'll end up having to > cut off the "inner" tie rod links also. They are just a rusty as this one, > and I imagine they'll all be spinners too. > > Thanks in advance for all your replies. > > -Les > > > > > On 9/18/06 2:57 PM, in article 450EFA13.66E55181@sympatico.ca, "Mike Romain" > <romainm@sympatico.ca> wrote: > >> To start you are posting in html and this is a text only group. Lots of >> folks don't use microcrap and your post isn't readable. Lots of servers >> cut them so they don't even make it or just the header with no body >> shows. >> >> Meanwhile, you sound like you are talking about the drag link ball joint >> that goes to the passenger wheel side from the steering. That is one >> piece. >> >> If the taper is gone, it can be an expensive fix to replace the whole >> steering knuckle or get a machine shop to fill and cut you a new taper >> in the hole once you get it off. >> >> I have a pair of needle nose vise grips I use for spinning ones. I get >> them between the ball and the knuckle arm on the bottom side and pray or >> cuss. I also soak the crap out of the castle nut with penetrating oil. >> >> I still have to cut off 'Way' too many of them..... >> >> The good news is it doesn't affect the front end alignment, only the >> steering wheel adjustment. The sleeve at the top end turns to adjust >> the angle of the steering wheel, so it is wise or just easier to mark it >> or measure it. It can be a bit of a pain getting the wheel back >> straight. If it isn't straight now, now's the time to fix it. ;-) >> >> Mike >> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 >> 88 Cherokee 235 BFG AT's >> Canadian Off Road Trips Photos: Non members can still view! >> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 >> (More Off Road album links at bottom of the view page) > |
Re: Tie Rod Issues and replacement
Les wrote:
> Just verified that XJ, ZJ, TJ tie rods are not the same type and > won't work. Guess I'll have to shell out the $100 for the new one. check with napaonline.com but only go with the NCP (napa chassis parts) line as the other cheaper line isn't that good. for OEM I deal with http://www.chryslerpartsdirect.com/ Just finished replacing the inner right joint (drag link to tie bar). -- DougW |
Re: Tie Rod Issues and replacement
Les wrote:
> Just verified that XJ, ZJ, TJ tie rods are not the same type and > won't work. Guess I'll have to shell out the $100 for the new one. check with napaonline.com but only go with the NCP (napa chassis parts) line as the other cheaper line isn't that good. for OEM I deal with http://www.chryslerpartsdirect.com/ Just finished replacing the inner right joint (drag link to tie bar). -- DougW |
Re: Tie Rod Issues and replacement
Les wrote:
> Just verified that XJ, ZJ, TJ tie rods are not the same type and > won't work. Guess I'll have to shell out the $100 for the new one. check with napaonline.com but only go with the NCP (napa chassis parts) line as the other cheaper line isn't that good. for OEM I deal with http://www.chryslerpartsdirect.com/ Just finished replacing the inner right joint (drag link to tie bar). -- DougW |
Re: Tie Rod Issues and replacement
Wow the OEM price ($45) is less than Napa or Autozone. That's rare.
On 9/18/06 3:51 PM, in article aFDPg.13224$JR5.6201@dukeread11, "DougW" <post.replies@invalid.address> wrote: > Les wrote: >> Just verified that XJ, ZJ, TJ tie rods are not the same type and >> won't work. Guess I'll have to shell out the $100 for the new one. > > check with napaonline.com but only go with the NCP (napa chassis parts) > line as the other cheaper line isn't that good. > > for OEM I deal with http://www.chryslerpartsdirect.com/ > > Just finished replacing the inner right joint (drag link to tie bar). |
Re: Tie Rod Issues and replacement
Wow the OEM price ($45) is less than Napa or Autozone. That's rare.
On 9/18/06 3:51 PM, in article aFDPg.13224$JR5.6201@dukeread11, "DougW" <post.replies@invalid.address> wrote: > Les wrote: >> Just verified that XJ, ZJ, TJ tie rods are not the same type and >> won't work. Guess I'll have to shell out the $100 for the new one. > > check with napaonline.com but only go with the NCP (napa chassis parts) > line as the other cheaper line isn't that good. > > for OEM I deal with http://www.chryslerpartsdirect.com/ > > Just finished replacing the inner right joint (drag link to tie bar). |
Re: Tie Rod Issues and replacement
Wow the OEM price ($45) is less than Napa or Autozone. That's rare.
On 9/18/06 3:51 PM, in article aFDPg.13224$JR5.6201@dukeread11, "DougW" <post.replies@invalid.address> wrote: > Les wrote: >> Just verified that XJ, ZJ, TJ tie rods are not the same type and >> won't work. Guess I'll have to shell out the $100 for the new one. > > check with napaonline.com but only go with the NCP (napa chassis parts) > line as the other cheaper line isn't that good. > > for OEM I deal with http://www.chryslerpartsdirect.com/ > > Just finished replacing the inner right joint (drag link to tie bar). |
Re: Tie Rod Issues and replacement
Oops wrong part. It's $143, ouch. Some sites have this listed as a Drag
link, while others list it as a tie rod.. Aaargh. On 9/18/06 4:23 PM, in article C134788D.8F08%nospam@nospam.com, "Les" <nospam@nospam.com> wrote: > Wow the OEM price ($45) is less than Napa or Autozone. That's rare. > > > > > On 9/18/06 3:51 PM, in article aFDPg.13224$JR5.6201@dukeread11, "DougW" > <post.replies@invalid.address> wrote: > >> Les wrote: >>> Just verified that XJ, ZJ, TJ tie rods are not the same type and >>> won't work. Guess I'll have to shell out the $100 for the new one. >> >> check with napaonline.com but only go with the NCP (napa chassis parts) >> line as the other cheaper line isn't that good. >> >> for OEM I deal with http://www.chryslerpartsdirect.com/ >> >> Just finished replacing the inner right joint (drag link to tie bar). > |
Re: Tie Rod Issues and replacement
Oops wrong part. It's $143, ouch. Some sites have this listed as a Drag
link, while others list it as a tie rod.. Aaargh. On 9/18/06 4:23 PM, in article C134788D.8F08%nospam@nospam.com, "Les" <nospam@nospam.com> wrote: > Wow the OEM price ($45) is less than Napa or Autozone. That's rare. > > > > > On 9/18/06 3:51 PM, in article aFDPg.13224$JR5.6201@dukeread11, "DougW" > <post.replies@invalid.address> wrote: > >> Les wrote: >>> Just verified that XJ, ZJ, TJ tie rods are not the same type and >>> won't work. Guess I'll have to shell out the $100 for the new one. >> >> check with napaonline.com but only go with the NCP (napa chassis parts) >> line as the other cheaper line isn't that good. >> >> for OEM I deal with http://www.chryslerpartsdirect.com/ >> >> Just finished replacing the inner right joint (drag link to tie bar). > |
Re: Tie Rod Issues and replacement
Oops wrong part. It's $143, ouch. Some sites have this listed as a Drag
link, while others list it as a tie rod.. Aaargh. On 9/18/06 4:23 PM, in article C134788D.8F08%nospam@nospam.com, "Les" <nospam@nospam.com> wrote: > Wow the OEM price ($45) is less than Napa or Autozone. That's rare. > > > > > On 9/18/06 3:51 PM, in article aFDPg.13224$JR5.6201@dukeread11, "DougW" > <post.replies@invalid.address> wrote: > >> Les wrote: >>> Just verified that XJ, ZJ, TJ tie rods are not the same type and >>> won't work. Guess I'll have to shell out the $100 for the new one. >> >> check with napaonline.com but only go with the NCP (napa chassis parts) >> line as the other cheaper line isn't that good. >> >> for OEM I deal with http://www.chryslerpartsdirect.com/ >> >> Just finished replacing the inner right joint (drag link to tie bar). > |
Re: Tie Rod Issues and replacement
Where are you located?
Carl "Les" <nospam@nospam.com> wrote in message news:C1347A3E.8F10%nospam@nospam.com... > Oops wrong part. It's $143, ouch. Some sites have this listed as a Drag > link, while others list it as a tie rod.. Aaargh. > > > > On 9/18/06 4:23 PM, in article C134788D.8F08%nospam@nospam.com, "Les" > <nospam@nospam.com> wrote: > >> Wow the OEM price ($45) is less than Napa or Autozone. That's rare. >> >> >> >> >> On 9/18/06 3:51 PM, in article aFDPg.13224$JR5.6201@dukeread11, "DougW" >> <post.replies@invalid.address> wrote: >> >>> Les wrote: >>>> Just verified that XJ, ZJ, TJ tie rods are not the same type and >>>> won't work. Guess I'll have to shell out the $100 for the new one. >>> >>> check with napaonline.com but only go with the NCP (napa chassis parts) >>> line as the other cheaper line isn't that good. >>> >>> for OEM I deal with http://www.chryslerpartsdirect.com/ >>> >>> Just finished replacing the inner right joint (drag link to tie bar). >> > |
Re: Tie Rod Issues and replacement
Where are you located?
Carl "Les" <nospam@nospam.com> wrote in message news:C1347A3E.8F10%nospam@nospam.com... > Oops wrong part. It's $143, ouch. Some sites have this listed as a Drag > link, while others list it as a tie rod.. Aaargh. > > > > On 9/18/06 4:23 PM, in article C134788D.8F08%nospam@nospam.com, "Les" > <nospam@nospam.com> wrote: > >> Wow the OEM price ($45) is less than Napa or Autozone. That's rare. >> >> >> >> >> On 9/18/06 3:51 PM, in article aFDPg.13224$JR5.6201@dukeread11, "DougW" >> <post.replies@invalid.address> wrote: >> >>> Les wrote: >>>> Just verified that XJ, ZJ, TJ tie rods are not the same type and >>>> won't work. Guess I'll have to shell out the $100 for the new one. >>> >>> check with napaonline.com but only go with the NCP (napa chassis parts) >>> line as the other cheaper line isn't that good. >>> >>> for OEM I deal with http://www.chryslerpartsdirect.com/ >>> >>> Just finished replacing the inner right joint (drag link to tie bar). >> > |
Re: Tie Rod Issues and replacement
Where are you located?
Carl "Les" <nospam@nospam.com> wrote in message news:C1347A3E.8F10%nospam@nospam.com... > Oops wrong part. It's $143, ouch. Some sites have this listed as a Drag > link, while others list it as a tie rod.. Aaargh. > > > > On 9/18/06 4:23 PM, in article C134788D.8F08%nospam@nospam.com, "Les" > <nospam@nospam.com> wrote: > >> Wow the OEM price ($45) is less than Napa or Autozone. That's rare. >> >> >> >> >> On 9/18/06 3:51 PM, in article aFDPg.13224$JR5.6201@dukeread11, "DougW" >> <post.replies@invalid.address> wrote: >> >>> Les wrote: >>>> Just verified that XJ, ZJ, TJ tie rods are not the same type and >>>> won't work. Guess I'll have to shell out the $100 for the new one. >>> >>> check with napaonline.com but only go with the NCP (napa chassis parts) >>> line as the other cheaper line isn't that good. >>> >>> for OEM I deal with http://www.chryslerpartsdirect.com/ >>> >>> Just finished replacing the inner right joint (drag link to tie bar). >> > |
Re: Tie Rod Issues and replacement
If you have an inmpact wrench, you can usually get those @#$% nuts
started by pushing the socket on so that it holds the rod fairly solid then bash the ball joint from the other side as you run the air. That will drive the taper in far enough to grab for a bit - might even hold to get it all the way off. When all else fails, you can usually cut the grease boot out of the way and get a pipe wrench or big pair of vice ripes on the lower part of the ball and/or the stem. Worst comes to worst, just drive the pickle fork in like you were pulling the thing out - that will usually hold them still as well - but you have to keep driving it tight as you go. On Mon, 18 Sep 2006 20:11:54 UTC Les <nospam@nospam.com> wrote: > Sorry about the HTML, did that fix it? At least you guys don't seem to mind > top posting. That really gets some groups in a bender! > > Ya, that's the piece I'm talking about. The long one that's parallel to the > axle and connects to the pass side spindle. Parts store was calling it an > outer tie rod end. > > As far as the replacement parts, do any of you know if XJ, ZJ, or any other > jeep models are compatible? I'd rather find a decent one at the salvage > yard, that pay the parts store $125 for a replacement. > > Also I have a feeling that when I take this one off, I'll end up having to > cut off the "inner" tie rod links also. They are just a rusty as this one, > and I imagine they'll all be spinners too. > > Thanks in advance for all your replies. > > -Les > > > > > On 9/18/06 2:57 PM, in article 450EFA13.66E55181@sympatico.ca, "Mike Romain" > <romainm@sympatico.ca> wrote: > > > To start you are posting in html and this is a text only group. Lots of > > folks don't use microcrap and your post isn't readable. Lots of servers > > cut them so they don't even make it or just the header with no body > > shows. > > > > Meanwhile, you sound like you are talking about the drag link ball joint > > that goes to the passenger wheel side from the steering. That is one > > piece. > > > > If the taper is gone, it can be an expensive fix to replace the whole > > steering knuckle or get a machine shop to fill and cut you a new taper > > in the hole once you get it off. > > > > I have a pair of needle nose vise grips I use for spinning ones. I get > > them between the ball and the knuckle arm on the bottom side and pray or > > cuss. I also soak the crap out of the castle nut with penetrating oil. > > > > I still have to cut off 'Way' too many of them..... > > > > The good news is it doesn't affect the front end alignment, only the > > steering wheel adjustment. The sleeve at the top end turns to adjust > > the angle of the steering wheel, so it is wise or just easier to mark it > > or measure it. It can be a bit of a pain getting the wheel back > > straight. If it isn't straight now, now's the time to fix it. ;-) > > > > Mike > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > > 88 Cherokee 235 BFG AT's > > Canadian Off Road Trips Photos: Non members can still view! > > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 > > (More Off Road album links at bottom of the view page) > -- Will Honea |
Re: Tie Rod Issues and replacement
If you have an inmpact wrench, you can usually get those @#$% nuts
started by pushing the socket on so that it holds the rod fairly solid then bash the ball joint from the other side as you run the air. That will drive the taper in far enough to grab for a bit - might even hold to get it all the way off. When all else fails, you can usually cut the grease boot out of the way and get a pipe wrench or big pair of vice ripes on the lower part of the ball and/or the stem. Worst comes to worst, just drive the pickle fork in like you were pulling the thing out - that will usually hold them still as well - but you have to keep driving it tight as you go. On Mon, 18 Sep 2006 20:11:54 UTC Les <nospam@nospam.com> wrote: > Sorry about the HTML, did that fix it? At least you guys don't seem to mind > top posting. That really gets some groups in a bender! > > Ya, that's the piece I'm talking about. The long one that's parallel to the > axle and connects to the pass side spindle. Parts store was calling it an > outer tie rod end. > > As far as the replacement parts, do any of you know if XJ, ZJ, or any other > jeep models are compatible? I'd rather find a decent one at the salvage > yard, that pay the parts store $125 for a replacement. > > Also I have a feeling that when I take this one off, I'll end up having to > cut off the "inner" tie rod links also. They are just a rusty as this one, > and I imagine they'll all be spinners too. > > Thanks in advance for all your replies. > > -Les > > > > > On 9/18/06 2:57 PM, in article 450EFA13.66E55181@sympatico.ca, "Mike Romain" > <romainm@sympatico.ca> wrote: > > > To start you are posting in html and this is a text only group. Lots of > > folks don't use microcrap and your post isn't readable. Lots of servers > > cut them so they don't even make it or just the header with no body > > shows. > > > > Meanwhile, you sound like you are talking about the drag link ball joint > > that goes to the passenger wheel side from the steering. That is one > > piece. > > > > If the taper is gone, it can be an expensive fix to replace the whole > > steering knuckle or get a machine shop to fill and cut you a new taper > > in the hole once you get it off. > > > > I have a pair of needle nose vise grips I use for spinning ones. I get > > them between the ball and the knuckle arm on the bottom side and pray or > > cuss. I also soak the crap out of the castle nut with penetrating oil. > > > > I still have to cut off 'Way' too many of them..... > > > > The good news is it doesn't affect the front end alignment, only the > > steering wheel adjustment. The sleeve at the top end turns to adjust > > the angle of the steering wheel, so it is wise or just easier to mark it > > or measure it. It can be a bit of a pain getting the wheel back > > straight. If it isn't straight now, now's the time to fix it. ;-) > > > > Mike > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > > 88 Cherokee 235 BFG AT's > > Canadian Off Road Trips Photos: Non members can still view! > > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 > > (More Off Road album links at bottom of the view page) > -- Will Honea |
Re: Tie Rod Issues and replacement
If you have an inmpact wrench, you can usually get those @#$% nuts
started by pushing the socket on so that it holds the rod fairly solid then bash the ball joint from the other side as you run the air. That will drive the taper in far enough to grab for a bit - might even hold to get it all the way off. When all else fails, you can usually cut the grease boot out of the way and get a pipe wrench or big pair of vice ripes on the lower part of the ball and/or the stem. Worst comes to worst, just drive the pickle fork in like you were pulling the thing out - that will usually hold them still as well - but you have to keep driving it tight as you go. On Mon, 18 Sep 2006 20:11:54 UTC Les <nospam@nospam.com> wrote: > Sorry about the HTML, did that fix it? At least you guys don't seem to mind > top posting. That really gets some groups in a bender! > > Ya, that's the piece I'm talking about. The long one that's parallel to the > axle and connects to the pass side spindle. Parts store was calling it an > outer tie rod end. > > As far as the replacement parts, do any of you know if XJ, ZJ, or any other > jeep models are compatible? I'd rather find a decent one at the salvage > yard, that pay the parts store $125 for a replacement. > > Also I have a feeling that when I take this one off, I'll end up having to > cut off the "inner" tie rod links also. They are just a rusty as this one, > and I imagine they'll all be spinners too. > > Thanks in advance for all your replies. > > -Les > > > > > On 9/18/06 2:57 PM, in article 450EFA13.66E55181@sympatico.ca, "Mike Romain" > <romainm@sympatico.ca> wrote: > > > To start you are posting in html and this is a text only group. Lots of > > folks don't use microcrap and your post isn't readable. Lots of servers > > cut them so they don't even make it or just the header with no body > > shows. > > > > Meanwhile, you sound like you are talking about the drag link ball joint > > that goes to the passenger wheel side from the steering. That is one > > piece. > > > > If the taper is gone, it can be an expensive fix to replace the whole > > steering knuckle or get a machine shop to fill and cut you a new taper > > in the hole once you get it off. > > > > I have a pair of needle nose vise grips I use for spinning ones. I get > > them between the ball and the knuckle arm on the bottom side and pray or > > cuss. I also soak the crap out of the castle nut with penetrating oil. > > > > I still have to cut off 'Way' too many of them..... > > > > The good news is it doesn't affect the front end alignment, only the > > steering wheel adjustment. The sleeve at the top end turns to adjust > > the angle of the steering wheel, so it is wise or just easier to mark it > > or measure it. It can be a bit of a pain getting the wheel back > > straight. If it isn't straight now, now's the time to fix it. ;-) > > > > Mike > > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > > 88 Cherokee 235 BFG AT's > > Canadian Off Road Trips Photos: Non members can still view! > > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590 > > (More Off Road album links at bottom of the view page) > -- Will Honea |
Re: Tie Rod Issues and replacement
Will Honea wrote:
> If you have an inmpact wrench, you can usually get those @#$% nuts > started by pushing the socket on so that it holds the rod fairly solid > then bash the ball joint from the other side as you run the air. That > will drive the taper in far enough to grab for a bit - might even hold > to get it all the way off. When all else fails, you can usually cut > the grease boot out of the way and get a pipe wrench or big pair of > vice ripes on the lower part of the ball and/or the stem. Worst comes > to worst, just drive the pickle fork in like you were pulling the > thing out - that will usually hold them still as well - but you have > to keep driving it tight as you go. at that point I'd probably drag out a nut-splitter or the cutoff wheel. -- DougW |
Re: Tie Rod Issues and replacement
Will Honea wrote:
> If you have an inmpact wrench, you can usually get those @#$% nuts > started by pushing the socket on so that it holds the rod fairly solid > then bash the ball joint from the other side as you run the air. That > will drive the taper in far enough to grab for a bit - might even hold > to get it all the way off. When all else fails, you can usually cut > the grease boot out of the way and get a pipe wrench or big pair of > vice ripes on the lower part of the ball and/or the stem. Worst comes > to worst, just drive the pickle fork in like you were pulling the > thing out - that will usually hold them still as well - but you have > to keep driving it tight as you go. at that point I'd probably drag out a nut-splitter or the cutoff wheel. -- DougW |
Re: Tie Rod Issues and replacement
Will Honea wrote:
> If you have an inmpact wrench, you can usually get those @#$% nuts > started by pushing the socket on so that it holds the rod fairly solid > then bash the ball joint from the other side as you run the air. That > will drive the taper in far enough to grab for a bit - might even hold > to get it all the way off. When all else fails, you can usually cut > the grease boot out of the way and get a pipe wrench or big pair of > vice ripes on the lower part of the ball and/or the stem. Worst comes > to worst, just drive the pickle fork in like you were pulling the > thing out - that will usually hold them still as well - but you have > to keep driving it tight as you go. at that point I'd probably drag out a nut-splitter or the cutoff wheel. -- DougW |
Re: Tie Rod Issues and replacement
Central Illinois.
On 9/18/06 9:31 PM, in article RcmdnRyakuUuy5LYnZ2dnUVZ_r-dnZ2d@comcast.com, "Carl" <carlsaiyed@hotmailREMOVE.com> wrote: > Where are you located? > > Carl > > "Les" <nospam@nospam.com> wrote in message > news:C1347A3E.8F10%nospam@nospam.com... >> Oops wrong part. It's $143, ouch. Some sites have this listed as a Drag >> link, while others list it as a tie rod.. Aaargh. >> >> >> >> On 9/18/06 4:23 PM, in article C134788D.8F08%nospam@nospam.com, "Les" >> <nospam@nospam.com> wrote: >> >>> Wow the OEM price ($45) is less than Napa or Autozone. That's rare. >>> >>> >>> >>> >>> On 9/18/06 3:51 PM, in article aFDPg.13224$JR5.6201@dukeread11, "DougW" >>> <post.replies@invalid.address> wrote: >>> >>>> Les wrote: >>>>> Just verified that XJ, ZJ, TJ tie rods are not the same type and >>>>> won't work. Guess I'll have to shell out the $100 for the new one. >>>> >>>> check with napaonline.com but only go with the NCP (napa chassis parts) >>>> line as the other cheaper line isn't that good. >>>> >>>> for OEM I deal with http://www.chryslerpartsdirect.com/ >>>> >>>> Just finished replacing the inner right joint (drag link to tie bar). >>> >> > > |
Re: Tie Rod Issues and replacement
Central Illinois.
On 9/18/06 9:31 PM, in article RcmdnRyakuUuy5LYnZ2dnUVZ_r-dnZ2d@comcast.com, "Carl" <carlsaiyed@hotmailREMOVE.com> wrote: > Where are you located? > > Carl > > "Les" <nospam@nospam.com> wrote in message > news:C1347A3E.8F10%nospam@nospam.com... >> Oops wrong part. It's $143, ouch. Some sites have this listed as a Drag >> link, while others list it as a tie rod.. Aaargh. >> >> >> >> On 9/18/06 4:23 PM, in article C134788D.8F08%nospam@nospam.com, "Les" >> <nospam@nospam.com> wrote: >> >>> Wow the OEM price ($45) is less than Napa or Autozone. That's rare. >>> >>> >>> >>> >>> On 9/18/06 3:51 PM, in article aFDPg.13224$JR5.6201@dukeread11, "DougW" >>> <post.replies@invalid.address> wrote: >>> >>>> Les wrote: >>>>> Just verified that XJ, ZJ, TJ tie rods are not the same type and >>>>> won't work. Guess I'll have to shell out the $100 for the new one. >>>> >>>> check with napaonline.com but only go with the NCP (napa chassis parts) >>>> line as the other cheaper line isn't that good. >>>> >>>> for OEM I deal with http://www.chryslerpartsdirect.com/ >>>> >>>> Just finished replacing the inner right joint (drag link to tie bar). >>> >> > > |
Re: Tie Rod Issues and replacement
Central Illinois.
On 9/18/06 9:31 PM, in article RcmdnRyakuUuy5LYnZ2dnUVZ_r-dnZ2d@comcast.com, "Carl" <carlsaiyed@hotmailREMOVE.com> wrote: > Where are you located? > > Carl > > "Les" <nospam@nospam.com> wrote in message > news:C1347A3E.8F10%nospam@nospam.com... >> Oops wrong part. It's $143, ouch. Some sites have this listed as a Drag >> link, while others list it as a tie rod.. Aaargh. >> >> >> >> On 9/18/06 4:23 PM, in article C134788D.8F08%nospam@nospam.com, "Les" >> <nospam@nospam.com> wrote: >> >>> Wow the OEM price ($45) is less than Napa or Autozone. That's rare. >>> >>> >>> >>> >>> On 9/18/06 3:51 PM, in article aFDPg.13224$JR5.6201@dukeread11, "DougW" >>> <post.replies@invalid.address> wrote: >>> >>>> Les wrote: >>>>> Just verified that XJ, ZJ, TJ tie rods are not the same type and >>>>> won't work. Guess I'll have to shell out the $100 for the new one. >>>> >>>> check with napaonline.com but only go with the NCP (napa chassis parts) >>>> line as the other cheaper line isn't that good. >>>> >>>> for OEM I deal with http://www.chryslerpartsdirect.com/ >>>> >>>> Just finished replacing the inner right joint (drag link to tie bar). >>> >> > > |
Re: Tie Rod Issues and replacement
I'm in the process of rounding up a nut splitter.
On 9/19/06 6:18 AM, in article tmQPg.13247$JR5.7209@dukeread11, "DougW" <post.replies@invalid.address> wrote: > > at that point I'd probably drag out a nut-splitter or the cutoff wheel. |
Re: Tie Rod Issues and replacement
I'm in the process of rounding up a nut splitter.
On 9/19/06 6:18 AM, in article tmQPg.13247$JR5.7209@dukeread11, "DougW" <post.replies@invalid.address> wrote: > > at that point I'd probably drag out a nut-splitter or the cutoff wheel. |
Re: Tie Rod Issues and replacement
I'm in the process of rounding up a nut splitter.
On 9/19/06 6:18 AM, in article tmQPg.13247$JR5.7209@dukeread11, "DougW" <post.replies@invalid.address> wrote: > > at that point I'd probably drag out a nut-splitter or the cutoff wheel. |
Re: Tie Rod Issues and replacement
Just found a complete used, but decent replacement for $20 from a guy in a
local Jeep Club. Cool. On 9/19/06 8:01 AM, in article C1355467.8F49%nospam@nospam.com, "Les" <nospam@nospam.com> wrote: > I'm in the process of rounding up a nut splitter. > > > On 9/19/06 6:18 AM, in article tmQPg.13247$JR5.7209@dukeread11, "DougW" > <post.replies@invalid.address> wrote: > > >> >> at that point I'd probably drag out a nut-splitter or the cutoff wheel. > |
Re: Tie Rod Issues and replacement
Just found a complete used, but decent replacement for $20 from a guy in a
local Jeep Club. Cool. On 9/19/06 8:01 AM, in article C1355467.8F49%nospam@nospam.com, "Les" <nospam@nospam.com> wrote: > I'm in the process of rounding up a nut splitter. > > > On 9/19/06 6:18 AM, in article tmQPg.13247$JR5.7209@dukeread11, "DougW" > <post.replies@invalid.address> wrote: > > >> >> at that point I'd probably drag out a nut-splitter or the cutoff wheel. > |
Re: Tie Rod Issues and replacement
Just found a complete used, but decent replacement for $20 from a guy in a
local Jeep Club. Cool. On 9/19/06 8:01 AM, in article C1355467.8F49%nospam@nospam.com, "Les" <nospam@nospam.com> wrote: > I'm in the process of rounding up a nut splitter. > > > On 9/19/06 6:18 AM, in article tmQPg.13247$JR5.7209@dukeread11, "DougW" > <post.replies@invalid.address> wrote: > > >> >> at that point I'd probably drag out a nut-splitter or the cutoff wheel. > |
All times are GMT -4. The time now is 06:55 AM. |
© 2024 MH Sub I, LLC dba Internet Brands