stalling on deceleration
10-14-2006, 03:07 PM
#11
Guest
Posts: n/a
Re: stalling on deceleration
Mike is the expert on the BBD here, unfortunately he is away wheeling this
weekend.
"Deano" <dpernisie@gmail.com> wrote in message
news:1160839466.261612.37870@i42g2000cwa.googlegro ups.com...
> Thanks Billy. I definitely was planning to address the idle tube
> issue, but wasn't sure that that would fix the quirky stalling problem
> I also have (decel/downhill stall, uphill revving).
>
> Any other thoughts?
>
> billy ray wrote:
>> Deano,
>>
>> Mike Romain has a fix for the idle tube problem he promotes, it was
>> actually
>> a fix that Jeep used for a while that involves drilling out the tubes
>> because they are too small from the factory. After the 'fix' all you
>> will
>> need in the way of maintenance is a carb rebuild every few years to
>> replace
>> the rubber parts and reset the float. If I remember correctly you can
>> perform this fix while leaving the bulk of the carb installed.
>>
>> Do a search on this newsgroup for "mike romain bbd fix" and I'm sure you
>> will find the procedure.
>>
>>
>>
>> "Deano" <dpernisie@gmail.com> wrote in message
>> news:1160824597.473728.119350@h48g2000cwc.googlegr oups.com...
>> >I have an 86 CJ7 with the 258 and Carter BBD on it.
>> >
>> > Here's my problem...
>> >
>> > I am about to undertake a full carburetor rebuild today with care to
>> > clean out those idle tubes and get all my settings right, but wanted to
>> > make sure I was solving my biggest idling problem at the same time.
>> >
>> > While my jeep struggles with cold mornings and idling in general, it
>> > also stalls on deceleration or downhill and revs higher on uphill (when
>> > idling). I originally thought it was a vacuum leak problem (which I
>> > will be checking for today as well) but wanted to see if there was
>> > another culprit I might be missing. One piece of advice suggested I
>> > check the float level which I will during the rebuild. Anything else?
>> >
>> > By the way, thanks to all the generous contributors on this group. I
>> > am amazed at the time and thoughtfulness that goes into responses. For
>> > me, a first time jeep owner (86 cj7), it has been a huge resource to
>> > get me up to speed.
>> >
>> > Deano
>> >
>
weekend.
"Deano" <dpernisie@gmail.com> wrote in message
news:1160839466.261612.37870@i42g2000cwa.googlegro ups.com...
> Thanks Billy. I definitely was planning to address the idle tube
> issue, but wasn't sure that that would fix the quirky stalling problem
> I also have (decel/downhill stall, uphill revving).
>
> Any other thoughts?
>
> billy ray wrote:
>> Deano,
>>
>> Mike Romain has a fix for the idle tube problem he promotes, it was
>> actually
>> a fix that Jeep used for a while that involves drilling out the tubes
>> because they are too small from the factory. After the 'fix' all you
>> will
>> need in the way of maintenance is a carb rebuild every few years to
>> replace
>> the rubber parts and reset the float. If I remember correctly you can
>> perform this fix while leaving the bulk of the carb installed.
>>
>> Do a search on this newsgroup for "mike romain bbd fix" and I'm sure you
>> will find the procedure.
>>
>>
>>
>> "Deano" <dpernisie@gmail.com> wrote in message
>> news:1160824597.473728.119350@h48g2000cwc.googlegr oups.com...
>> >I have an 86 CJ7 with the 258 and Carter BBD on it.
>> >
>> > Here's my problem...
>> >
>> > I am about to undertake a full carburetor rebuild today with care to
>> > clean out those idle tubes and get all my settings right, but wanted to
>> > make sure I was solving my biggest idling problem at the same time.
>> >
>> > While my jeep struggles with cold mornings and idling in general, it
>> > also stalls on deceleration or downhill and revs higher on uphill (when
>> > idling). I originally thought it was a vacuum leak problem (which I
>> > will be checking for today as well) but wanted to see if there was
>> > another culprit I might be missing. One piece of advice suggested I
>> > check the float level which I will during the rebuild. Anything else?
>> >
>> > By the way, thanks to all the generous contributors on this group. I
>> > am amazed at the time and thoughtfulness that goes into responses. For
>> > me, a first time jeep owner (86 cj7), it has been a huge resource to
>> > get me up to speed.
>> >
>> > Deano
>> >
>
10-14-2006, 03:07 PM
#12
Guest
Posts: n/a
Re: stalling on deceleration
Mike is the expert on the BBD here, unfortunately he is away wheeling this
weekend.
"Deano" <dpernisie@gmail.com> wrote in message
news:1160839466.261612.37870@i42g2000cwa.googlegro ups.com...
> Thanks Billy. I definitely was planning to address the idle tube
> issue, but wasn't sure that that would fix the quirky stalling problem
> I also have (decel/downhill stall, uphill revving).
>
> Any other thoughts?
>
> billy ray wrote:
>> Deano,
>>
>> Mike Romain has a fix for the idle tube problem he promotes, it was
>> actually
>> a fix that Jeep used for a while that involves drilling out the tubes
>> because they are too small from the factory. After the 'fix' all you
>> will
>> need in the way of maintenance is a carb rebuild every few years to
>> replace
>> the rubber parts and reset the float. If I remember correctly you can
>> perform this fix while leaving the bulk of the carb installed.
>>
>> Do a search on this newsgroup for "mike romain bbd fix" and I'm sure you
>> will find the procedure.
>>
>>
>>
>> "Deano" <dpernisie@gmail.com> wrote in message
>> news:1160824597.473728.119350@h48g2000cwc.googlegr oups.com...
>> >I have an 86 CJ7 with the 258 and Carter BBD on it.
>> >
>> > Here's my problem...
>> >
>> > I am about to undertake a full carburetor rebuild today with care to
>> > clean out those idle tubes and get all my settings right, but wanted to
>> > make sure I was solving my biggest idling problem at the same time.
>> >
>> > While my jeep struggles with cold mornings and idling in general, it
>> > also stalls on deceleration or downhill and revs higher on uphill (when
>> > idling). I originally thought it was a vacuum leak problem (which I
>> > will be checking for today as well) but wanted to see if there was
>> > another culprit I might be missing. One piece of advice suggested I
>> > check the float level which I will during the rebuild. Anything else?
>> >
>> > By the way, thanks to all the generous contributors on this group. I
>> > am amazed at the time and thoughtfulness that goes into responses. For
>> > me, a first time jeep owner (86 cj7), it has been a huge resource to
>> > get me up to speed.
>> >
>> > Deano
>> >
>
weekend.
"Deano" <dpernisie@gmail.com> wrote in message
news:1160839466.261612.37870@i42g2000cwa.googlegro ups.com...
> Thanks Billy. I definitely was planning to address the idle tube
> issue, but wasn't sure that that would fix the quirky stalling problem
> I also have (decel/downhill stall, uphill revving).
>
> Any other thoughts?
>
> billy ray wrote:
>> Deano,
>>
>> Mike Romain has a fix for the idle tube problem he promotes, it was
>> actually
>> a fix that Jeep used for a while that involves drilling out the tubes
>> because they are too small from the factory. After the 'fix' all you
>> will
>> need in the way of maintenance is a carb rebuild every few years to
>> replace
>> the rubber parts and reset the float. If I remember correctly you can
>> perform this fix while leaving the bulk of the carb installed.
>>
>> Do a search on this newsgroup for "mike romain bbd fix" and I'm sure you
>> will find the procedure.
>>
>>
>>
>> "Deano" <dpernisie@gmail.com> wrote in message
>> news:1160824597.473728.119350@h48g2000cwc.googlegr oups.com...
>> >I have an 86 CJ7 with the 258 and Carter BBD on it.
>> >
>> > Here's my problem...
>> >
>> > I am about to undertake a full carburetor rebuild today with care to
>> > clean out those idle tubes and get all my settings right, but wanted to
>> > make sure I was solving my biggest idling problem at the same time.
>> >
>> > While my jeep struggles with cold mornings and idling in general, it
>> > also stalls on deceleration or downhill and revs higher on uphill (when
>> > idling). I originally thought it was a vacuum leak problem (which I
>> > will be checking for today as well) but wanted to see if there was
>> > another culprit I might be missing. One piece of advice suggested I
>> > check the float level which I will during the rebuild. Anything else?
>> >
>> > By the way, thanks to all the generous contributors on this group. I
>> > am amazed at the time and thoughtfulness that goes into responses. For
>> > me, a first time jeep owner (86 cj7), it has been a huge resource to
>> > get me up to speed.
>> >
>> > Deano
>> >
>
10-14-2006, 03:07 PM
#13
Guest
Posts: n/a
Re: stalling on deceleration
Mike is the expert on the BBD here, unfortunately he is away wheeling this
weekend.
"Deano" <dpernisie@gmail.com> wrote in message
news:1160839466.261612.37870@i42g2000cwa.googlegro ups.com...
> Thanks Billy. I definitely was planning to address the idle tube
> issue, but wasn't sure that that would fix the quirky stalling problem
> I also have (decel/downhill stall, uphill revving).
>
> Any other thoughts?
>
> billy ray wrote:
>> Deano,
>>
>> Mike Romain has a fix for the idle tube problem he promotes, it was
>> actually
>> a fix that Jeep used for a while that involves drilling out the tubes
>> because they are too small from the factory. After the 'fix' all you
>> will
>> need in the way of maintenance is a carb rebuild every few years to
>> replace
>> the rubber parts and reset the float. If I remember correctly you can
>> perform this fix while leaving the bulk of the carb installed.
>>
>> Do a search on this newsgroup for "mike romain bbd fix" and I'm sure you
>> will find the procedure.
>>
>>
>>
>> "Deano" <dpernisie@gmail.com> wrote in message
>> news:1160824597.473728.119350@h48g2000cwc.googlegr oups.com...
>> >I have an 86 CJ7 with the 258 and Carter BBD on it.
>> >
>> > Here's my problem...
>> >
>> > I am about to undertake a full carburetor rebuild today with care to
>> > clean out those idle tubes and get all my settings right, but wanted to
>> > make sure I was solving my biggest idling problem at the same time.
>> >
>> > While my jeep struggles with cold mornings and idling in general, it
>> > also stalls on deceleration or downhill and revs higher on uphill (when
>> > idling). I originally thought it was a vacuum leak problem (which I
>> > will be checking for today as well) but wanted to see if there was
>> > another culprit I might be missing. One piece of advice suggested I
>> > check the float level which I will during the rebuild. Anything else?
>> >
>> > By the way, thanks to all the generous contributors on this group. I
>> > am amazed at the time and thoughtfulness that goes into responses. For
>> > me, a first time jeep owner (86 cj7), it has been a huge resource to
>> > get me up to speed.
>> >
>> > Deano
>> >
>
weekend.
"Deano" <dpernisie@gmail.com> wrote in message
news:1160839466.261612.37870@i42g2000cwa.googlegro ups.com...
> Thanks Billy. I definitely was planning to address the idle tube
> issue, but wasn't sure that that would fix the quirky stalling problem
> I also have (decel/downhill stall, uphill revving).
>
> Any other thoughts?
>
> billy ray wrote:
>> Deano,
>>
>> Mike Romain has a fix for the idle tube problem he promotes, it was
>> actually
>> a fix that Jeep used for a while that involves drilling out the tubes
>> because they are too small from the factory. After the 'fix' all you
>> will
>> need in the way of maintenance is a carb rebuild every few years to
>> replace
>> the rubber parts and reset the float. If I remember correctly you can
>> perform this fix while leaving the bulk of the carb installed.
>>
>> Do a search on this newsgroup for "mike romain bbd fix" and I'm sure you
>> will find the procedure.
>>
>>
>>
>> "Deano" <dpernisie@gmail.com> wrote in message
>> news:1160824597.473728.119350@h48g2000cwc.googlegr oups.com...
>> >I have an 86 CJ7 with the 258 and Carter BBD on it.
>> >
>> > Here's my problem...
>> >
>> > I am about to undertake a full carburetor rebuild today with care to
>> > clean out those idle tubes and get all my settings right, but wanted to
>> > make sure I was solving my biggest idling problem at the same time.
>> >
>> > While my jeep struggles with cold mornings and idling in general, it
>> > also stalls on deceleration or downhill and revs higher on uphill (when
>> > idling). I originally thought it was a vacuum leak problem (which I
>> > will be checking for today as well) but wanted to see if there was
>> > another culprit I might be missing. One piece of advice suggested I
>> > check the float level which I will during the rebuild. Anything else?
>> >
>> > By the way, thanks to all the generous contributors on this group. I
>> > am amazed at the time and thoughtfulness that goes into responses. For
>> > me, a first time jeep owner (86 cj7), it has been a huge resource to
>> > get me up to speed.
>> >
>> > Deano
>> >
>
10-14-2006, 11:47 PM
#14
Guest
Posts: n/a
Re: stalling on deceleration
May find some help form this YJ site:
http://home.sprynet.com/~dale02/list.htm
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
Deano wrote:
>
> Thanks Billy. I definitely was planning to address the idle tube
> issue, but wasn't sure that that would fix the quirky stalling problem
> I also have (decel/downhill stall, uphill revving).
>
> Any other thoughts?
http://home.sprynet.com/~dale02/list.htm
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
Deano wrote:
>
> Thanks Billy. I definitely was planning to address the idle tube
> issue, but wasn't sure that that would fix the quirky stalling problem
> I also have (decel/downhill stall, uphill revving).
>
> Any other thoughts?
10-14-2006, 11:47 PM
#15
Guest
Posts: n/a
Re: stalling on deceleration
May find some help form this YJ site:
http://home.sprynet.com/~dale02/list.htm
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
Deano wrote:
>
> Thanks Billy. I definitely was planning to address the idle tube
> issue, but wasn't sure that that would fix the quirky stalling problem
> I also have (decel/downhill stall, uphill revving).
>
> Any other thoughts?
http://home.sprynet.com/~dale02/list.htm
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
Deano wrote:
>
> Thanks Billy. I definitely was planning to address the idle tube
> issue, but wasn't sure that that would fix the quirky stalling problem
> I also have (decel/downhill stall, uphill revving).
>
> Any other thoughts?
10-14-2006, 11:47 PM
#16
Guest
Posts: n/a
Re: stalling on deceleration
May find some help form this YJ site:
http://home.sprynet.com/~dale02/list.htm
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
Deano wrote:
>
> Thanks Billy. I definitely was planning to address the idle tube
> issue, but wasn't sure that that would fix the quirky stalling problem
> I also have (decel/downhill stall, uphill revving).
>
> Any other thoughts?
http://home.sprynet.com/~dale02/list.htm
God Bless America, Bill O|||||||O
mailto:-------------------- http://www.----------.com/
Deano wrote:
>
> Thanks Billy. I definitely was planning to address the idle tube
> issue, but wasn't sure that that would fix the quirky stalling problem
> I also have (decel/downhill stall, uphill revving).
>
> Any other thoughts?
10-15-2006, 11:04 AM
#17
Guest
Posts: n/a
Re: stalling on deceleration
Thanks for the thoughts guys. The carb rebuild and idle tube clean-out
(didn't the 1/32" for the permanent fix - next time) worked magic. It
cold starts perfectly, idles perfectly and runs strong.
L.W.(Bill) ------ III wrote:
> May find some help form this YJ site:
> http://home.sprynet.com/~dale02/list.htm
> God Bless America, Bill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
> Deano wrote:
> >
> > Thanks Billy. I definitely was planning to address the idle tube
> > issue, but wasn't sure that that would fix the quirky stalling problem
> > I also have (decel/downhill stall, uphill revving).
> >
> > Any other thoughts?
(didn't the 1/32" for the permanent fix - next time) worked magic. It
cold starts perfectly, idles perfectly and runs strong.
L.W.(Bill) ------ III wrote:
> May find some help form this YJ site:
> http://home.sprynet.com/~dale02/list.htm
> God Bless America, Bill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
> Deano wrote:
> >
> > Thanks Billy. I definitely was planning to address the idle tube
> > issue, but wasn't sure that that would fix the quirky stalling problem
> > I also have (decel/downhill stall, uphill revving).
> >
> > Any other thoughts?
10-15-2006, 11:04 AM
#18
Guest
Posts: n/a
Re: stalling on deceleration
Thanks for the thoughts guys. The carb rebuild and idle tube clean-out
(didn't the 1/32" for the permanent fix - next time) worked magic. It
cold starts perfectly, idles perfectly and runs strong.
L.W.(Bill) ------ III wrote:
> May find some help form this YJ site:
> http://home.sprynet.com/~dale02/list.htm
> God Bless America, Bill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
> Deano wrote:
> >
> > Thanks Billy. I definitely was planning to address the idle tube
> > issue, but wasn't sure that that would fix the quirky stalling problem
> > I also have (decel/downhill stall, uphill revving).
> >
> > Any other thoughts?
(didn't the 1/32" for the permanent fix - next time) worked magic. It
cold starts perfectly, idles perfectly and runs strong.
L.W.(Bill) ------ III wrote:
> May find some help form this YJ site:
> http://home.sprynet.com/~dale02/list.htm
> God Bless America, Bill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
> Deano wrote:
> >
> > Thanks Billy. I definitely was planning to address the idle tube
> > issue, but wasn't sure that that would fix the quirky stalling problem
> > I also have (decel/downhill stall, uphill revving).
> >
> > Any other thoughts?
10-15-2006, 11:04 AM
#19
Guest
Posts: n/a
Re: stalling on deceleration
Thanks for the thoughts guys. The carb rebuild and idle tube clean-out
(didn't the 1/32" for the permanent fix - next time) worked magic. It
cold starts perfectly, idles perfectly and runs strong.
L.W.(Bill) ------ III wrote:
> May find some help form this YJ site:
> http://home.sprynet.com/~dale02/list.htm
> God Bless America, Bill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
> Deano wrote:
> >
> > Thanks Billy. I definitely was planning to address the idle tube
> > issue, but wasn't sure that that would fix the quirky stalling problem
> > I also have (decel/downhill stall, uphill revving).
> >
> > Any other thoughts?
(didn't the 1/32" for the permanent fix - next time) worked magic. It
cold starts perfectly, idles perfectly and runs strong.
L.W.(Bill) ------ III wrote:
> May find some help form this YJ site:
> http://home.sprynet.com/~dale02/list.htm
> God Bless America, Bill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
> Deano wrote:
> >
> > Thanks Billy. I definitely was planning to address the idle tube
> > issue, but wasn't sure that that would fix the quirky stalling problem
> > I also have (decel/downhill stall, uphill revving).
> >
> > Any other thoughts?
10-15-2006, 11:09 AM
#20
Guest
Posts: n/a
Re: stalling on deceleration
The 'fix' is designed to prevent it from happening again I believe but
regular applications of GumOut JetSpray may keep the tubes clean and clear.
"Deano" <dpernisie@gmail.com> wrote in message
news:1160924645.206369.45200@b28g2000cwb.googlegro ups.com...
> Thanks for the thoughts guys. The carb rebuild and idle tube clean-out
> (didn't the 1/32" for the permanent fix - next time) worked magic. It
> cold starts perfectly, idles perfectly and runs strong.
>
> L.W.(Bill) ------ III wrote:
>> May find some help form this YJ site:
>> http://home.sprynet.com/~dale02/list.htm
>> God Bless America, Bill O|||||||O
>> mailto:-------------------- http://www.----------.com/
>>
>> Deano wrote:
>> >
>> > Thanks Billy. I definitely was planning to address the idle tube
>> > issue, but wasn't sure that that would fix the quirky stalling problem
>> > I also have (decel/downhill stall, uphill revving).
>> >
>> > Any other thoughts?
>
regular applications of GumOut JetSpray may keep the tubes clean and clear.
"Deano" <dpernisie@gmail.com> wrote in message
news:1160924645.206369.45200@b28g2000cwb.googlegro ups.com...
> Thanks for the thoughts guys. The carb rebuild and idle tube clean-out
> (didn't the 1/32" for the permanent fix - next time) worked magic. It
> cold starts perfectly, idles perfectly and runs strong.
>
> L.W.(Bill) ------ III wrote:
>> May find some help form this YJ site:
>> http://home.sprynet.com/~dale02/list.htm
>> God Bless America, Bill O|||||||O
>> mailto:-------------------- http://www.----------.com/
>>
>> Deano wrote:
>> >
>> > Thanks Billy. I definitely was planning to address the idle tube
>> > issue, but wasn't sure that that would fix the quirky stalling problem
>> > I also have (decel/downhill stall, uphill revving).
>> >
>> > Any other thoughts?
>
