seatbelts in rear seat of a CJ
#21
Guest
Posts: n/a
Re: seatbelts in rear seat of a CJ
Nope. for the CJ-5 go talk to a fab job to make a roll cage. Mike is
correct on the difference. Adding a true cage will give you much more
protection than a sport bar which is not really intended for a offroad type
roll over.
"Steve" <stevncin@charter.net> wrote in message
news:kXiUe.8190$tc7.3263@fe03.lga...
>I should have mentioned...its for a CJ-5 ..will it work the same way??
>
>
> "Rusted" <noEmail@please.com> wrote in message
> news:1giUe.11906$ea5.10946@fe53.usenetserver.com.. .
>> Install a roll cage from a 92-95 YJ. The cage will bolt to your CJ, you
>> need to figure out a way to attach the new cage to the windshield (using
>> a nutzert or similar). Then you have a place to bolt 3-point belts for
>> the rear passengers. That is the easiest way to get it done. Also see
>> if any of the local 4x4 fab shops can make somethinig for you. Maybe
>> they can add to your current cage, or better yet a full roll cage so the
>> people up front are safe too.
>>
>>
>> "Steve" <stevncin@charter.net> wrote in message
>> news:7rhUe.28798$ih4.16730@fe02.lga...
>>> Anybody had luck with installing some kind of seatbelt with a shoulder
>>> strap on the back seat of a CJ? If so how was this done?
>>>
>>> Thanks
>>>
>>
>>
>>
>
>
correct on the difference. Adding a true cage will give you much more
protection than a sport bar which is not really intended for a offroad type
roll over.
"Steve" <stevncin@charter.net> wrote in message
news:kXiUe.8190$tc7.3263@fe03.lga...
>I should have mentioned...its for a CJ-5 ..will it work the same way??
>
>
> "Rusted" <noEmail@please.com> wrote in message
> news:1giUe.11906$ea5.10946@fe53.usenetserver.com.. .
>> Install a roll cage from a 92-95 YJ. The cage will bolt to your CJ, you
>> need to figure out a way to attach the new cage to the windshield (using
>> a nutzert or similar). Then you have a place to bolt 3-point belts for
>> the rear passengers. That is the easiest way to get it done. Also see
>> if any of the local 4x4 fab shops can make somethinig for you. Maybe
>> they can add to your current cage, or better yet a full roll cage so the
>> people up front are safe too.
>>
>>
>> "Steve" <stevncin@charter.net> wrote in message
>> news:7rhUe.28798$ih4.16730@fe02.lga...
>>> Anybody had luck with installing some kind of seatbelt with a shoulder
>>> strap on the back seat of a CJ? If so how was this done?
>>>
>>> Thanks
>>>
>>
>>
>>
>
>
#22
Guest
Posts: n/a
Re: seatbelts in rear seat of a CJ
Like Rusted mentions, nope.
If I was going to get a custom one made, I would make sure it would tie
into the frame. I did this when I went to a fiberglass body on my CJ7.
Basically I put a steel plate under the floor that I bolted the bar down
to and made sure it would reach to the frame mount so the front feet of
the bar are tagged to the mount. I plan on doing the rear legs the
same, but need new tails on my frame first. So I have 'half' a roll bar
sort of...
There are companies that make kits to tie the CJ7 bars to the frame like
I did. Not hard to fab up once you see how it is done though.
Here is a link to one company and it says it covers CJ5 frame tie ins
too.
http://www.4wd.com/shop/productlist....5&category=287
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Steve wrote:
>
> I should have mentioned...its for a CJ-5 ..will it work the same way??
>
> "Rusted" <noEmail@please.com> wrote in message
> news:1giUe.11906$ea5.10946@fe53.usenetserver.com.. .
> > Install a roll cage from a 92-95 YJ. The cage will bolt to your CJ, you
> > need to figure out a way to attach the new cage to the windshield (using a
> > nutzert or similar). Then you have a place to bolt 3-point belts for the
> > rear passengers. That is the easiest way to get it done. Also see if
> > any of the local 4x4 fab shops can make somethinig for you. Maybe they
> > can add to your current cage, or better yet a full roll cage so the people
> > up front are safe too.
> >
> >
> > "Steve" <stevncin@charter.net> wrote in message
> > news:7rhUe.28798$ih4.16730@fe02.lga...
> >> Anybody had luck with installing some kind of seatbelt with a shoulder
> >> strap on the back seat of a CJ? If so how was this done?
> >>
> >> Thanks
> >>
> >
> >
> >
If I was going to get a custom one made, I would make sure it would tie
into the frame. I did this when I went to a fiberglass body on my CJ7.
Basically I put a steel plate under the floor that I bolted the bar down
to and made sure it would reach to the frame mount so the front feet of
the bar are tagged to the mount. I plan on doing the rear legs the
same, but need new tails on my frame first. So I have 'half' a roll bar
sort of...
There are companies that make kits to tie the CJ7 bars to the frame like
I did. Not hard to fab up once you see how it is done though.
Here is a link to one company and it says it covers CJ5 frame tie ins
too.
http://www.4wd.com/shop/productlist....5&category=287
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Steve wrote:
>
> I should have mentioned...its for a CJ-5 ..will it work the same way??
>
> "Rusted" <noEmail@please.com> wrote in message
> news:1giUe.11906$ea5.10946@fe53.usenetserver.com.. .
> > Install a roll cage from a 92-95 YJ. The cage will bolt to your CJ, you
> > need to figure out a way to attach the new cage to the windshield (using a
> > nutzert or similar). Then you have a place to bolt 3-point belts for the
> > rear passengers. That is the easiest way to get it done. Also see if
> > any of the local 4x4 fab shops can make somethinig for you. Maybe they
> > can add to your current cage, or better yet a full roll cage so the people
> > up front are safe too.
> >
> >
> > "Steve" <stevncin@charter.net> wrote in message
> > news:7rhUe.28798$ih4.16730@fe02.lga...
> >> Anybody had luck with installing some kind of seatbelt with a shoulder
> >> strap on the back seat of a CJ? If so how was this done?
> >>
> >> Thanks
> >>
> >
> >
> >
#23
Guest
Posts: n/a
Re: seatbelts in rear seat of a CJ
Like Rusted mentions, nope.
If I was going to get a custom one made, I would make sure it would tie
into the frame. I did this when I went to a fiberglass body on my CJ7.
Basically I put a steel plate under the floor that I bolted the bar down
to and made sure it would reach to the frame mount so the front feet of
the bar are tagged to the mount. I plan on doing the rear legs the
same, but need new tails on my frame first. So I have 'half' a roll bar
sort of...
There are companies that make kits to tie the CJ7 bars to the frame like
I did. Not hard to fab up once you see how it is done though.
Here is a link to one company and it says it covers CJ5 frame tie ins
too.
http://www.4wd.com/shop/productlist....5&category=287
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Steve wrote:
>
> I should have mentioned...its for a CJ-5 ..will it work the same way??
>
> "Rusted" <noEmail@please.com> wrote in message
> news:1giUe.11906$ea5.10946@fe53.usenetserver.com.. .
> > Install a roll cage from a 92-95 YJ. The cage will bolt to your CJ, you
> > need to figure out a way to attach the new cage to the windshield (using a
> > nutzert or similar). Then you have a place to bolt 3-point belts for the
> > rear passengers. That is the easiest way to get it done. Also see if
> > any of the local 4x4 fab shops can make somethinig for you. Maybe they
> > can add to your current cage, or better yet a full roll cage so the people
> > up front are safe too.
> >
> >
> > "Steve" <stevncin@charter.net> wrote in message
> > news:7rhUe.28798$ih4.16730@fe02.lga...
> >> Anybody had luck with installing some kind of seatbelt with a shoulder
> >> strap on the back seat of a CJ? If so how was this done?
> >>
> >> Thanks
> >>
> >
> >
> >
If I was going to get a custom one made, I would make sure it would tie
into the frame. I did this when I went to a fiberglass body on my CJ7.
Basically I put a steel plate under the floor that I bolted the bar down
to and made sure it would reach to the frame mount so the front feet of
the bar are tagged to the mount. I plan on doing the rear legs the
same, but need new tails on my frame first. So I have 'half' a roll bar
sort of...
There are companies that make kits to tie the CJ7 bars to the frame like
I did. Not hard to fab up once you see how it is done though.
Here is a link to one company and it says it covers CJ5 frame tie ins
too.
http://www.4wd.com/shop/productlist....5&category=287
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Steve wrote:
>
> I should have mentioned...its for a CJ-5 ..will it work the same way??
>
> "Rusted" <noEmail@please.com> wrote in message
> news:1giUe.11906$ea5.10946@fe53.usenetserver.com.. .
> > Install a roll cage from a 92-95 YJ. The cage will bolt to your CJ, you
> > need to figure out a way to attach the new cage to the windshield (using a
> > nutzert or similar). Then you have a place to bolt 3-point belts for the
> > rear passengers. That is the easiest way to get it done. Also see if
> > any of the local 4x4 fab shops can make somethinig for you. Maybe they
> > can add to your current cage, or better yet a full roll cage so the people
> > up front are safe too.
> >
> >
> > "Steve" <stevncin@charter.net> wrote in message
> > news:7rhUe.28798$ih4.16730@fe02.lga...
> >> Anybody had luck with installing some kind of seatbelt with a shoulder
> >> strap on the back seat of a CJ? If so how was this done?
> >>
> >> Thanks
> >>
> >
> >
> >
#24
Guest
Posts: n/a
Re: seatbelts in rear seat of a CJ
Like Rusted mentions, nope.
If I was going to get a custom one made, I would make sure it would tie
into the frame. I did this when I went to a fiberglass body on my CJ7.
Basically I put a steel plate under the floor that I bolted the bar down
to and made sure it would reach to the frame mount so the front feet of
the bar are tagged to the mount. I plan on doing the rear legs the
same, but need new tails on my frame first. So I have 'half' a roll bar
sort of...
There are companies that make kits to tie the CJ7 bars to the frame like
I did. Not hard to fab up once you see how it is done though.
Here is a link to one company and it says it covers CJ5 frame tie ins
too.
http://www.4wd.com/shop/productlist....5&category=287
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Steve wrote:
>
> I should have mentioned...its for a CJ-5 ..will it work the same way??
>
> "Rusted" <noEmail@please.com> wrote in message
> news:1giUe.11906$ea5.10946@fe53.usenetserver.com.. .
> > Install a roll cage from a 92-95 YJ. The cage will bolt to your CJ, you
> > need to figure out a way to attach the new cage to the windshield (using a
> > nutzert or similar). Then you have a place to bolt 3-point belts for the
> > rear passengers. That is the easiest way to get it done. Also see if
> > any of the local 4x4 fab shops can make somethinig for you. Maybe they
> > can add to your current cage, or better yet a full roll cage so the people
> > up front are safe too.
> >
> >
> > "Steve" <stevncin@charter.net> wrote in message
> > news:7rhUe.28798$ih4.16730@fe02.lga...
> >> Anybody had luck with installing some kind of seatbelt with a shoulder
> >> strap on the back seat of a CJ? If so how was this done?
> >>
> >> Thanks
> >>
> >
> >
> >
If I was going to get a custom one made, I would make sure it would tie
into the frame. I did this when I went to a fiberglass body on my CJ7.
Basically I put a steel plate under the floor that I bolted the bar down
to and made sure it would reach to the frame mount so the front feet of
the bar are tagged to the mount. I plan on doing the rear legs the
same, but need new tails on my frame first. So I have 'half' a roll bar
sort of...
There are companies that make kits to tie the CJ7 bars to the frame like
I did. Not hard to fab up once you see how it is done though.
Here is a link to one company and it says it covers CJ5 frame tie ins
too.
http://www.4wd.com/shop/productlist....5&category=287
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Steve wrote:
>
> I should have mentioned...its for a CJ-5 ..will it work the same way??
>
> "Rusted" <noEmail@please.com> wrote in message
> news:1giUe.11906$ea5.10946@fe53.usenetserver.com.. .
> > Install a roll cage from a 92-95 YJ. The cage will bolt to your CJ, you
> > need to figure out a way to attach the new cage to the windshield (using a
> > nutzert or similar). Then you have a place to bolt 3-point belts for the
> > rear passengers. That is the easiest way to get it done. Also see if
> > any of the local 4x4 fab shops can make somethinig for you. Maybe they
> > can add to your current cage, or better yet a full roll cage so the people
> > up front are safe too.
> >
> >
> > "Steve" <stevncin@charter.net> wrote in message
> > news:7rhUe.28798$ih4.16730@fe02.lga...
> >> Anybody had luck with installing some kind of seatbelt with a shoulder
> >> strap on the back seat of a CJ? If so how was this done?
> >>
> >> Thanks
> >>
> >
> >
> >
#25
Guest
Posts: n/a
Re: seatbelts in rear seat of a CJ
Like Rusted mentions, nope.
If I was going to get a custom one made, I would make sure it would tie
into the frame. I did this when I went to a fiberglass body on my CJ7.
Basically I put a steel plate under the floor that I bolted the bar down
to and made sure it would reach to the frame mount so the front feet of
the bar are tagged to the mount. I plan on doing the rear legs the
same, but need new tails on my frame first. So I have 'half' a roll bar
sort of...
There are companies that make kits to tie the CJ7 bars to the frame like
I did. Not hard to fab up once you see how it is done though.
Here is a link to one company and it says it covers CJ5 frame tie ins
too.
http://www.4wd.com/shop/productlist....5&category=287
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Steve wrote:
>
> I should have mentioned...its for a CJ-5 ..will it work the same way??
>
> "Rusted" <noEmail@please.com> wrote in message
> news:1giUe.11906$ea5.10946@fe53.usenetserver.com.. .
> > Install a roll cage from a 92-95 YJ. The cage will bolt to your CJ, you
> > need to figure out a way to attach the new cage to the windshield (using a
> > nutzert or similar). Then you have a place to bolt 3-point belts for the
> > rear passengers. That is the easiest way to get it done. Also see if
> > any of the local 4x4 fab shops can make somethinig for you. Maybe they
> > can add to your current cage, or better yet a full roll cage so the people
> > up front are safe too.
> >
> >
> > "Steve" <stevncin@charter.net> wrote in message
> > news:7rhUe.28798$ih4.16730@fe02.lga...
> >> Anybody had luck with installing some kind of seatbelt with a shoulder
> >> strap on the back seat of a CJ? If so how was this done?
> >>
> >> Thanks
> >>
> >
> >
> >
If I was going to get a custom one made, I would make sure it would tie
into the frame. I did this when I went to a fiberglass body on my CJ7.
Basically I put a steel plate under the floor that I bolted the bar down
to and made sure it would reach to the frame mount so the front feet of
the bar are tagged to the mount. I plan on doing the rear legs the
same, but need new tails on my frame first. So I have 'half' a roll bar
sort of...
There are companies that make kits to tie the CJ7 bars to the frame like
I did. Not hard to fab up once you see how it is done though.
Here is a link to one company and it says it covers CJ5 frame tie ins
too.
http://www.4wd.com/shop/productlist....5&category=287
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Steve wrote:
>
> I should have mentioned...its for a CJ-5 ..will it work the same way??
>
> "Rusted" <noEmail@please.com> wrote in message
> news:1giUe.11906$ea5.10946@fe53.usenetserver.com.. .
> > Install a roll cage from a 92-95 YJ. The cage will bolt to your CJ, you
> > need to figure out a way to attach the new cage to the windshield (using a
> > nutzert or similar). Then you have a place to bolt 3-point belts for the
> > rear passengers. That is the easiest way to get it done. Also see if
> > any of the local 4x4 fab shops can make somethinig for you. Maybe they
> > can add to your current cage, or better yet a full roll cage so the people
> > up front are safe too.
> >
> >
> > "Steve" <stevncin@charter.net> wrote in message
> > news:7rhUe.28798$ih4.16730@fe02.lga...
> >> Anybody had luck with installing some kind of seatbelt with a shoulder
> >> strap on the back seat of a CJ? If so how was this done?
> >>
> >> Thanks
> >>
> >
> >
> >
Thread
Thread Starter
Forum
Replies
Last Post
Nathan Otis
Jeep Mailing List
0
07-05-2004 02:37 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)