Ring and pinion - tech answer needed
Guest
Posts: n/a
Ring and pinion - tech answer needed
I am selling a ring and pinion from a front end Dana 30, 3.73 from a
TJ2002. Some one asked the following question:
Hi, I have a 1981 CJ5 with a Dana 30 front end. I just changed the
rear end from a AMC20 with a ratio of 2.50, to a Dana 44 with a ratio
of 3.73. I need the front and rear to match up. Do you know if your
R&P work in my front end, or would there be any differences that I
dont know about. Thank you
So can he use it?
TJ2002. Some one asked the following question:
Hi, I have a 1981 CJ5 with a Dana 30 front end. I just changed the
rear end from a AMC20 with a ratio of 2.50, to a Dana 44 with a ratio
of 3.73. I need the front and rear to match up. Do you know if your
R&P work in my front end, or would there be any differences that I
dont know about. Thank you
So can he use it?
Guest
Posts: n/a
Re: Ring and pinion - tech answer needed
I would bet the ring and pinion would fit. There's the reverse cut
used in the YJ that, of course won't:
http://www.off-road.com/jeep/tech/axle/d30.html He'll need the carrier
too: http://www.----------.com/tooth_count.txt
God Bless America, ßill O|||||||O
mailto:--------------------
Snowboardripper wrote:
>
> I am selling a ring and pinion from a front end Dana 30, 3.73 from a
> TJ2002. Some one asked the following question:
>
> Hi, I have a 1981 CJ5 with a Dana 30 front end. I just changed the
> rear end from a AMC20 with a ratio of 2.50, to a Dana 44 with a ratio
> of 3.73. I need the front and rear to match up. Do you know if your
> R&P work in my front end, or would there be any differences that I
> dont know about. Thank you
>
> So can he use it?
used in the YJ that, of course won't:
http://www.off-road.com/jeep/tech/axle/d30.html He'll need the carrier
too: http://www.----------.com/tooth_count.txt
God Bless America, ßill O|||||||O
mailto:--------------------
Snowboardripper wrote:
>
> I am selling a ring and pinion from a front end Dana 30, 3.73 from a
> TJ2002. Some one asked the following question:
>
> Hi, I have a 1981 CJ5 with a Dana 30 front end. I just changed the
> rear end from a AMC20 with a ratio of 2.50, to a Dana 44 with a ratio
> of 3.73. I need the front and rear to match up. Do you know if your
> R&P work in my front end, or would there be any differences that I
> dont know about. Thank you
>
> So can he use it?
Guest
Posts: n/a
Re: Ring and pinion - tech answer needed
I would bet the ring and pinion would fit. There's the reverse cut
used in the YJ that, of course won't:
http://www.off-road.com/jeep/tech/axle/d30.html He'll need the carrier
too: http://www.----------.com/tooth_count.txt
God Bless America, ßill O|||||||O
mailto:--------------------
Snowboardripper wrote:
>
> I am selling a ring and pinion from a front end Dana 30, 3.73 from a
> TJ2002. Some one asked the following question:
>
> Hi, I have a 1981 CJ5 with a Dana 30 front end. I just changed the
> rear end from a AMC20 with a ratio of 2.50, to a Dana 44 with a ratio
> of 3.73. I need the front and rear to match up. Do you know if your
> R&P work in my front end, or would there be any differences that I
> dont know about. Thank you
>
> So can he use it?
used in the YJ that, of course won't:
http://www.off-road.com/jeep/tech/axle/d30.html He'll need the carrier
too: http://www.----------.com/tooth_count.txt
God Bless America, ßill O|||||||O
mailto:--------------------
Snowboardripper wrote:
>
> I am selling a ring and pinion from a front end Dana 30, 3.73 from a
> TJ2002. Some one asked the following question:
>
> Hi, I have a 1981 CJ5 with a Dana 30 front end. I just changed the
> rear end from a AMC20 with a ratio of 2.50, to a Dana 44 with a ratio
> of 3.73. I need the front and rear to match up. Do you know if your
> R&P work in my front end, or would there be any differences that I
> dont know about. Thank you
>
> So can he use it?
Guest
Posts: n/a
Re: Ring and pinion - tech answer needed
I would bet the ring and pinion would fit. There's the reverse cut
used in the YJ that, of course won't:
http://www.off-road.com/jeep/tech/axle/d30.html He'll need the carrier
too: http://www.----------.com/tooth_count.txt
God Bless America, ßill O|||||||O
mailto:--------------------
Snowboardripper wrote:
>
> I am selling a ring and pinion from a front end Dana 30, 3.73 from a
> TJ2002. Some one asked the following question:
>
> Hi, I have a 1981 CJ5 with a Dana 30 front end. I just changed the
> rear end from a AMC20 with a ratio of 2.50, to a Dana 44 with a ratio
> of 3.73. I need the front and rear to match up. Do you know if your
> R&P work in my front end, or would there be any differences that I
> dont know about. Thank you
>
> So can he use it?
used in the YJ that, of course won't:
http://www.off-road.com/jeep/tech/axle/d30.html He'll need the carrier
too: http://www.----------.com/tooth_count.txt
God Bless America, ßill O|||||||O
mailto:--------------------
Snowboardripper wrote:
>
> I am selling a ring and pinion from a front end Dana 30, 3.73 from a
> TJ2002. Some one asked the following question:
>
> Hi, I have a 1981 CJ5 with a Dana 30 front end. I just changed the
> rear end from a AMC20 with a ratio of 2.50, to a Dana 44 with a ratio
> of 3.73. I need the front and rear to match up. Do you know if your
> R&P work in my front end, or would there be any differences that I
> dont know about. Thank you
>
> So can he use it?
Guest
Posts: n/a
Re: Ring and pinion - tech answer needed
I would bet the ring and pinion would fit. There's the reverse cut
used in the YJ that, of course won't:
http://www.off-road.com/jeep/tech/axle/d30.html He'll need the carrier
too: http://www.----------.com/tooth_count.txt
God Bless America, ßill O|||||||O
mailto:--------------------
Snowboardripper wrote:
>
> I am selling a ring and pinion from a front end Dana 30, 3.73 from a
> TJ2002. Some one asked the following question:
>
> Hi, I have a 1981 CJ5 with a Dana 30 front end. I just changed the
> rear end from a AMC20 with a ratio of 2.50, to a Dana 44 with a ratio
> of 3.73. I need the front and rear to match up. Do you know if your
> R&P work in my front end, or would there be any differences that I
> dont know about. Thank you
>
> So can he use it?
used in the YJ that, of course won't:
http://www.off-road.com/jeep/tech/axle/d30.html He'll need the carrier
too: http://www.----------.com/tooth_count.txt
God Bless America, ßill O|||||||O
mailto:--------------------
Snowboardripper wrote:
>
> I am selling a ring and pinion from a front end Dana 30, 3.73 from a
> TJ2002. Some one asked the following question:
>
> Hi, I have a 1981 CJ5 with a Dana 30 front end. I just changed the
> rear end from a AMC20 with a ratio of 2.50, to a Dana 44 with a ratio
> of 3.73. I need the front and rear to match up. Do you know if your
> R&P work in my front end, or would there be any differences that I
> dont know about. Thank you
>
> So can he use it?
Guest
Posts: n/a
Re: Ring and pinion - tech answer needed
I'll take that bet. Both are standard cut, but if memory serves, the
TJ/ZJ pinion is shorter than the CJ. If you look at any R&P catalog
you'll see different part numbers for CJ, TJ/ZJ, and XJ/YJ respectively.
Steve
http://xjeep.dyndns.org
L.W.(ßill) ------ III wrote:
> I would bet the ring and pinion would fit. There's the reverse cut
> used in the YJ that, of course won't:
> http://www.off-road.com/jeep/tech/axle/d30.html He'll need the carrier
> too: http://www.----------.com/tooth_count.txt
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> Snowboardripper wrote:
>
>>I am selling a ring and pinion from a front end Dana 30, 3.73 from a
>>TJ2002. Some one asked the following question:
>>
>>Hi, I have a 1981 CJ5 with a Dana 30 front end. I just changed the
>>rear end from a AMC20 with a ratio of 2.50, to a Dana 44 with a ratio
>>of 3.73. I need the front and rear to match up. Do you know if your
>>R&P work in my front end, or would there be any differences that I
>>dont know about. Thank you
>>
>>So can he use it?
TJ/ZJ pinion is shorter than the CJ. If you look at any R&P catalog
you'll see different part numbers for CJ, TJ/ZJ, and XJ/YJ respectively.
Steve
http://xjeep.dyndns.org
L.W.(ßill) ------ III wrote:
> I would bet the ring and pinion would fit. There's the reverse cut
> used in the YJ that, of course won't:
> http://www.off-road.com/jeep/tech/axle/d30.html He'll need the carrier
> too: http://www.----------.com/tooth_count.txt
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> Snowboardripper wrote:
>
>>I am selling a ring and pinion from a front end Dana 30, 3.73 from a
>>TJ2002. Some one asked the following question:
>>
>>Hi, I have a 1981 CJ5 with a Dana 30 front end. I just changed the
>>rear end from a AMC20 with a ratio of 2.50, to a Dana 44 with a ratio
>>of 3.73. I need the front and rear to match up. Do you know if your
>>R&P work in my front end, or would there be any differences that I
>>dont know about. Thank you
>>
>>So can he use it?
Guest
Posts: n/a
Re: Ring and pinion - tech answer needed
I'll take that bet. Both are standard cut, but if memory serves, the
TJ/ZJ pinion is shorter than the CJ. If you look at any R&P catalog
you'll see different part numbers for CJ, TJ/ZJ, and XJ/YJ respectively.
Steve
http://xjeep.dyndns.org
L.W.(ßill) ------ III wrote:
> I would bet the ring and pinion would fit. There's the reverse cut
> used in the YJ that, of course won't:
> http://www.off-road.com/jeep/tech/axle/d30.html He'll need the carrier
> too: http://www.----------.com/tooth_count.txt
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> Snowboardripper wrote:
>
>>I am selling a ring and pinion from a front end Dana 30, 3.73 from a
>>TJ2002. Some one asked the following question:
>>
>>Hi, I have a 1981 CJ5 with a Dana 30 front end. I just changed the
>>rear end from a AMC20 with a ratio of 2.50, to a Dana 44 with a ratio
>>of 3.73. I need the front and rear to match up. Do you know if your
>>R&P work in my front end, or would there be any differences that I
>>dont know about. Thank you
>>
>>So can he use it?
TJ/ZJ pinion is shorter than the CJ. If you look at any R&P catalog
you'll see different part numbers for CJ, TJ/ZJ, and XJ/YJ respectively.
Steve
http://xjeep.dyndns.org
L.W.(ßill) ------ III wrote:
> I would bet the ring and pinion would fit. There's the reverse cut
> used in the YJ that, of course won't:
> http://www.off-road.com/jeep/tech/axle/d30.html He'll need the carrier
> too: http://www.----------.com/tooth_count.txt
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> Snowboardripper wrote:
>
>>I am selling a ring and pinion from a front end Dana 30, 3.73 from a
>>TJ2002. Some one asked the following question:
>>
>>Hi, I have a 1981 CJ5 with a Dana 30 front end. I just changed the
>>rear end from a AMC20 with a ratio of 2.50, to a Dana 44 with a ratio
>>of 3.73. I need the front and rear to match up. Do you know if your
>>R&P work in my front end, or would there be any differences that I
>>dont know about. Thank you
>>
>>So can he use it?
Guest
Posts: n/a
Re: Ring and pinion - tech answer needed
I'll take that bet. Both are standard cut, but if memory serves, the
TJ/ZJ pinion is shorter than the CJ. If you look at any R&P catalog
you'll see different part numbers for CJ, TJ/ZJ, and XJ/YJ respectively.
Steve
http://xjeep.dyndns.org
L.W.(ßill) ------ III wrote:
> I would bet the ring and pinion would fit. There's the reverse cut
> used in the YJ that, of course won't:
> http://www.off-road.com/jeep/tech/axle/d30.html He'll need the carrier
> too: http://www.----------.com/tooth_count.txt
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> Snowboardripper wrote:
>
>>I am selling a ring and pinion from a front end Dana 30, 3.73 from a
>>TJ2002. Some one asked the following question:
>>
>>Hi, I have a 1981 CJ5 with a Dana 30 front end. I just changed the
>>rear end from a AMC20 with a ratio of 2.50, to a Dana 44 with a ratio
>>of 3.73. I need the front and rear to match up. Do you know if your
>>R&P work in my front end, or would there be any differences that I
>>dont know about. Thank you
>>
>>So can he use it?
TJ/ZJ pinion is shorter than the CJ. If you look at any R&P catalog
you'll see different part numbers for CJ, TJ/ZJ, and XJ/YJ respectively.
Steve
http://xjeep.dyndns.org
L.W.(ßill) ------ III wrote:
> I would bet the ring and pinion would fit. There's the reverse cut
> used in the YJ that, of course won't:
> http://www.off-road.com/jeep/tech/axle/d30.html He'll need the carrier
> too: http://www.----------.com/tooth_count.txt
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> Snowboardripper wrote:
>
>>I am selling a ring and pinion from a front end Dana 30, 3.73 from a
>>TJ2002. Some one asked the following question:
>>
>>Hi, I have a 1981 CJ5 with a Dana 30 front end. I just changed the
>>rear end from a AMC20 with a ratio of 2.50, to a Dana 44 with a ratio
>>of 3.73. I need the front and rear to match up. Do you know if your
>>R&P work in my front end, or would there be any differences that I
>>dont know about. Thank you
>>
>>So can he use it?
Guest
Posts: n/a
Re: Ring and pinion - tech answer needed
I'll take that bet. Both are standard cut, but if memory serves, the
TJ/ZJ pinion is shorter than the CJ. If you look at any R&P catalog
you'll see different part numbers for CJ, TJ/ZJ, and XJ/YJ respectively.
Steve
http://xjeep.dyndns.org
L.W.(ßill) ------ III wrote:
> I would bet the ring and pinion would fit. There's the reverse cut
> used in the YJ that, of course won't:
> http://www.off-road.com/jeep/tech/axle/d30.html He'll need the carrier
> too: http://www.----------.com/tooth_count.txt
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> Snowboardripper wrote:
>
>>I am selling a ring and pinion from a front end Dana 30, 3.73 from a
>>TJ2002. Some one asked the following question:
>>
>>Hi, I have a 1981 CJ5 with a Dana 30 front end. I just changed the
>>rear end from a AMC20 with a ratio of 2.50, to a Dana 44 with a ratio
>>of 3.73. I need the front and rear to match up. Do you know if your
>>R&P work in my front end, or would there be any differences that I
>>dont know about. Thank you
>>
>>So can he use it?
TJ/ZJ pinion is shorter than the CJ. If you look at any R&P catalog
you'll see different part numbers for CJ, TJ/ZJ, and XJ/YJ respectively.
Steve
http://xjeep.dyndns.org
L.W.(ßill) ------ III wrote:
> I would bet the ring and pinion would fit. There's the reverse cut
> used in the YJ that, of course won't:
> http://www.off-road.com/jeep/tech/axle/d30.html He'll need the carrier
> too: http://www.----------.com/tooth_count.txt
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> Snowboardripper wrote:
>
>>I am selling a ring and pinion from a front end Dana 30, 3.73 from a
>>TJ2002. Some one asked the following question:
>>
>>Hi, I have a 1981 CJ5 with a Dana 30 front end. I just changed the
>>rear end from a AMC20 with a ratio of 2.50, to a Dana 44 with a ratio
>>of 3.73. I need the front and rear to match up. Do you know if your
>>R&P work in my front end, or would there be any differences that I
>>dont know about. Thank you
>>
>>So can he use it?
Guest
Posts: n/a
Re: Ring and pinion - tech answer needed
We are talking about 3.73 ratio, Summit makes no distinction:
http://store.summitracing.com/defaul...inion&x=19&y=9
I'll take a hundred.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Steve wrote:
>
> I'll take that bet. Both are standard cut, but if memory serves, the
> TJ/ZJ pinion is shorter than the CJ. If you look at any R&P catalog
> you'll see different part numbers for CJ, TJ/ZJ, and XJ/YJ respectively.
>
> Steve
> http://xjeep.dyndns.org
http://store.summitracing.com/defaul...inion&x=19&y=9
I'll take a hundred.
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Steve wrote:
>
> I'll take that bet. Both are standard cut, but if memory serves, the
> TJ/ZJ pinion is shorter than the CJ. If you look at any R&P catalog
> you'll see different part numbers for CJ, TJ/ZJ, and XJ/YJ respectively.
>
> Steve
> http://xjeep.dyndns.org
