Re: How much of a pain to pull the driver door panel on a 95 ZJ Limited?
10-13-2005, 11:03 PM
#1
Guest
Posts: n/a
Re: How much of a pain to pull the driver door panel on a 95 ZJ Limited?
Lon did pass the time by typing:
> Window motor or mechanism making very slight grumbling noises only when
> rolling up, not down.
>
> How much of a pain in the nose is it to pull the driver door panels off
> to get at the thing to see if it is falling apart or just needs a few
> shots of lithium grease or similar?
Mostly it's enclosed but the track and hinge might need some attention.
> I have the FSM, but sometimes they tend to be a bit optimistic.
If it's like the 93 then just remove all the screws and slowly
pry the panel back. Watch the fingers, that plastic is suprisingly
sharp, cut the crap out of myself the first time.
Dunno if you have the little peggy things like these
http://www.revbeergoggles.com/temp/door-tree.jpg
Sometimes they break.. Dealer want's too freaking much for them.
I bought a bag of 50 from http://www.thecliplink.com/
DOOR TRIM PANEL RETAINER 18915 1 6.15
(this says Chrysler Caravan, Cirrus, Neon, Stratus & Voyager #6504014 1995-on
but it's the same as the Jeep part, just white, not yellow, whaaaah!)
JEEP SCREW GROMMET - 25 19276 1 5.33
--
DougW
> Window motor or mechanism making very slight grumbling noises only when
> rolling up, not down.
>
> How much of a pain in the nose is it to pull the driver door panels off
> to get at the thing to see if it is falling apart or just needs a few
> shots of lithium grease or similar?
Mostly it's enclosed but the track and hinge might need some attention.
> I have the FSM, but sometimes they tend to be a bit optimistic.
If it's like the 93 then just remove all the screws and slowly
pry the panel back. Watch the fingers, that plastic is suprisingly
sharp, cut the crap out of myself the first time.
Dunno if you have the little peggy things like these
http://www.revbeergoggles.com/temp/door-tree.jpg
Sometimes they break.. Dealer want's too freaking much for them.
I bought a bag of 50 from http://www.thecliplink.com/
DOOR TRIM PANEL RETAINER 18915 1 6.15
(this says Chrysler Caravan, Cirrus, Neon, Stratus & Voyager #6504014 1995-on
but it's the same as the Jeep part, just white, not yellow, whaaaah!)
JEEP SCREW GROMMET - 25 19276 1 5.33
--
DougW
10-13-2005, 11:08 PM
#2
Guest
Posts: n/a
Re: How much of a pain to pull the driver door panel on a 95 ZJ Limited?
Thanks will give it a shot. i know it has pop fasteners, dunno if the
type that ger old and hard. If I see them, I might just order a few
before I get a round tuit.
Just don't want anything busting in the meantime...
DougW proclaimed:
> Lon did pass the time by typing:
>
>>Window motor or mechanism making very slight grumbling noises only when
>>rolling up, not down.
>>
>>How much of a pain in the nose is it to pull the driver door panels off
>>to get at the thing to see if it is falling apart or just needs a few
>>shots of lithium grease or similar?
>
>
> Mostly it's enclosed but the track and hinge might need some attention.
>
>
>>I have the FSM, but sometimes they tend to be a bit optimistic.
>
>
> If it's like the 93 then just remove all the screws and slowly
> pry the panel back. Watch the fingers, that plastic is suprisingly
> sharp, cut the crap out of myself the first time.
>
> Dunno if you have the little peggy things like these
> http://www.revbeergoggles.com/temp/door-tree.jpg
> Sometimes they break.. Dealer want's too freaking much for them.
> I bought a bag of 50 from http://www.thecliplink.com/
>
> DOOR TRIM PANEL RETAINER 18915 1 6.15
>
> (this says Chrysler Caravan, Cirrus, Neon, Stratus & Voyager #6504014 1995-on
> but it's the same as the Jeep part, just white, not yellow, whaaaah!)
>
> JEEP SCREW GROMMET - 25 19276 1 5.33
>
type that ger old and hard. If I see them, I might just order a few
before I get a round tuit.
Just don't want anything busting in the meantime...
DougW proclaimed:
> Lon did pass the time by typing:
>
>>Window motor or mechanism making very slight grumbling noises only when
>>rolling up, not down.
>>
>>How much of a pain in the nose is it to pull the driver door panels off
>>to get at the thing to see if it is falling apart or just needs a few
>>shots of lithium grease or similar?
>
>
> Mostly it's enclosed but the track and hinge might need some attention.
>
>
>>I have the FSM, but sometimes they tend to be a bit optimistic.
>
>
> If it's like the 93 then just remove all the screws and slowly
> pry the panel back. Watch the fingers, that plastic is suprisingly
> sharp, cut the crap out of myself the first time.
>
> Dunno if you have the little peggy things like these
> http://www.revbeergoggles.com/temp/door-tree.jpg
> Sometimes they break.. Dealer want's too freaking much for them.
> I bought a bag of 50 from http://www.thecliplink.com/
>
> DOOR TRIM PANEL RETAINER 18915 1 6.15
>
> (this says Chrysler Caravan, Cirrus, Neon, Stratus & Voyager #6504014 1995-on
> but it's the same as the Jeep part, just white, not yellow, whaaaah!)
>
> JEEP SCREW GROMMET - 25 19276 1 5.33
>
10-13-2005, 11:08 PM
#3
Guest
Posts: n/a
Re: How much of a pain to pull the driver door panel on a 95 ZJ Limited?
Thanks will give it a shot. i know it has pop fasteners, dunno if the
type that ger old and hard. If I see them, I might just order a few
before I get a round tuit.
Just don't want anything busting in the meantime...
DougW proclaimed:
> Lon did pass the time by typing:
>
>>Window motor or mechanism making very slight grumbling noises only when
>>rolling up, not down.
>>
>>How much of a pain in the nose is it to pull the driver door panels off
>>to get at the thing to see if it is falling apart or just needs a few
>>shots of lithium grease or similar?
>
>
> Mostly it's enclosed but the track and hinge might need some attention.
>
>
>>I have the FSM, but sometimes they tend to be a bit optimistic.
>
>
> If it's like the 93 then just remove all the screws and slowly
> pry the panel back. Watch the fingers, that plastic is suprisingly
> sharp, cut the crap out of myself the first time.
>
> Dunno if you have the little peggy things like these
> http://www.revbeergoggles.com/temp/door-tree.jpg
> Sometimes they break.. Dealer want's too freaking much for them.
> I bought a bag of 50 from http://www.thecliplink.com/
>
> DOOR TRIM PANEL RETAINER 18915 1 6.15
>
> (this says Chrysler Caravan, Cirrus, Neon, Stratus & Voyager #6504014 1995-on
> but it's the same as the Jeep part, just white, not yellow, whaaaah!)
>
> JEEP SCREW GROMMET - 25 19276 1 5.33
>
type that ger old and hard. If I see them, I might just order a few
before I get a round tuit.
Just don't want anything busting in the meantime...
DougW proclaimed:
> Lon did pass the time by typing:
>
>>Window motor or mechanism making very slight grumbling noises only when
>>rolling up, not down.
>>
>>How much of a pain in the nose is it to pull the driver door panels off
>>to get at the thing to see if it is falling apart or just needs a few
>>shots of lithium grease or similar?
>
>
> Mostly it's enclosed but the track and hinge might need some attention.
>
>
>>I have the FSM, but sometimes they tend to be a bit optimistic.
>
>
> If it's like the 93 then just remove all the screws and slowly
> pry the panel back. Watch the fingers, that plastic is suprisingly
> sharp, cut the crap out of myself the first time.
>
> Dunno if you have the little peggy things like these
> http://www.revbeergoggles.com/temp/door-tree.jpg
> Sometimes they break.. Dealer want's too freaking much for them.
> I bought a bag of 50 from http://www.thecliplink.com/
>
> DOOR TRIM PANEL RETAINER 18915 1 6.15
>
> (this says Chrysler Caravan, Cirrus, Neon, Stratus & Voyager #6504014 1995-on
> but it's the same as the Jeep part, just white, not yellow, whaaaah!)
>
> JEEP SCREW GROMMET - 25 19276 1 5.33
>
10-13-2005, 11:08 PM
#4
Guest
Posts: n/a
Re: How much of a pain to pull the driver door panel on a 95 ZJ Limited?
Thanks will give it a shot. i know it has pop fasteners, dunno if the
type that ger old and hard. If I see them, I might just order a few
before I get a round tuit.
Just don't want anything busting in the meantime...
DougW proclaimed:
> Lon did pass the time by typing:
>
>>Window motor or mechanism making very slight grumbling noises only when
>>rolling up, not down.
>>
>>How much of a pain in the nose is it to pull the driver door panels off
>>to get at the thing to see if it is falling apart or just needs a few
>>shots of lithium grease or similar?
>
>
> Mostly it's enclosed but the track and hinge might need some attention.
>
>
>>I have the FSM, but sometimes they tend to be a bit optimistic.
>
>
> If it's like the 93 then just remove all the screws and slowly
> pry the panel back. Watch the fingers, that plastic is suprisingly
> sharp, cut the crap out of myself the first time.
>
> Dunno if you have the little peggy things like these
> http://www.revbeergoggles.com/temp/door-tree.jpg
> Sometimes they break.. Dealer want's too freaking much for them.
> I bought a bag of 50 from http://www.thecliplink.com/
>
> DOOR TRIM PANEL RETAINER 18915 1 6.15
>
> (this says Chrysler Caravan, Cirrus, Neon, Stratus & Voyager #6504014 1995-on
> but it's the same as the Jeep part, just white, not yellow, whaaaah!)
>
> JEEP SCREW GROMMET - 25 19276 1 5.33
>
type that ger old and hard. If I see them, I might just order a few
before I get a round tuit.
Just don't want anything busting in the meantime...
DougW proclaimed:
> Lon did pass the time by typing:
>
>>Window motor or mechanism making very slight grumbling noises only when
>>rolling up, not down.
>>
>>How much of a pain in the nose is it to pull the driver door panels off
>>to get at the thing to see if it is falling apart or just needs a few
>>shots of lithium grease or similar?
>
>
> Mostly it's enclosed but the track and hinge might need some attention.
>
>
>>I have the FSM, but sometimes they tend to be a bit optimistic.
>
>
> If it's like the 93 then just remove all the screws and slowly
> pry the panel back. Watch the fingers, that plastic is suprisingly
> sharp, cut the crap out of myself the first time.
>
> Dunno if you have the little peggy things like these
> http://www.revbeergoggles.com/temp/door-tree.jpg
> Sometimes they break.. Dealer want's too freaking much for them.
> I bought a bag of 50 from http://www.thecliplink.com/
>
> DOOR TRIM PANEL RETAINER 18915 1 6.15
>
> (this says Chrysler Caravan, Cirrus, Neon, Stratus & Voyager #6504014 1995-on
> but it's the same as the Jeep part, just white, not yellow, whaaaah!)
>
> JEEP SCREW GROMMET - 25 19276 1 5.33
>
10-13-2005, 11:26 PM
#5
Guest
Posts: n/a
Re: How much of a pain to pull the driver door panel on a 95 ZJ Limited?
Lon did pass the time by typing:
> Thanks will give it a shot. i know it has pop fasteners, dunno if the
> type that ger old and hard. If I see them, I might just order a few
> before I get a round tuit.
>
> Just don't want anything busting in the meantime...
The pegs tend to crack. Then all you get is a bit of squeek
from the door panel. thecliplink has a minimum order but I just
picked up a few bags of different bits for other folks to make it
over 20$ (I think that was the number)
--
DougW
> Thanks will give it a shot. i know it has pop fasteners, dunno if the
> type that ger old and hard. If I see them, I might just order a few
> before I get a round tuit.
>
> Just don't want anything busting in the meantime...
The pegs tend to crack. Then all you get is a bit of squeek
from the door panel. thecliplink has a minimum order but I just
picked up a few bags of different bits for other folks to make it
over 20$ (I think that was the number)
--
DougW
10-13-2005, 11:26 PM
#6
Guest
Posts: n/a
Re: How much of a pain to pull the driver door panel on a 95 ZJ Limited?
Lon did pass the time by typing:
> Thanks will give it a shot. i know it has pop fasteners, dunno if the
> type that ger old and hard. If I see them, I might just order a few
> before I get a round tuit.
>
> Just don't want anything busting in the meantime...
The pegs tend to crack. Then all you get is a bit of squeek
from the door panel. thecliplink has a minimum order but I just
picked up a few bags of different bits for other folks to make it
over 20$ (I think that was the number)
--
DougW
> Thanks will give it a shot. i know it has pop fasteners, dunno if the
> type that ger old and hard. If I see them, I might just order a few
> before I get a round tuit.
>
> Just don't want anything busting in the meantime...
The pegs tend to crack. Then all you get is a bit of squeek
from the door panel. thecliplink has a minimum order but I just
picked up a few bags of different bits for other folks to make it
over 20$ (I think that was the number)
--
DougW
10-13-2005, 11:26 PM
#7
Guest
Posts: n/a
Re: How much of a pain to pull the driver door panel on a 95 ZJ Limited?
Lon did pass the time by typing:
> Thanks will give it a shot. i know it has pop fasteners, dunno if the
> type that ger old and hard. If I see them, I might just order a few
> before I get a round tuit.
>
> Just don't want anything busting in the meantime...
The pegs tend to crack. Then all you get is a bit of squeek
from the door panel. thecliplink has a minimum order but I just
picked up a few bags of different bits for other folks to make it
over 20$ (I think that was the number)
--
DougW
> Thanks will give it a shot. i know it has pop fasteners, dunno if the
> type that ger old and hard. If I see them, I might just order a few
> before I get a round tuit.
>
> Just don't want anything busting in the meantime...
The pegs tend to crack. Then all you get is a bit of squeek
from the door panel. thecliplink has a minimum order but I just
picked up a few bags of different bits for other folks to make it
over 20$ (I think that was the number)
--
DougW
Thread
Thread Starter
Forum
Replies
Last Post
HilllClimb
Jeep & 4x4 Items For Sale
0
10-23-2012 06:30 PM
jeep videos
Jeep Videos - Pictures
0
04-10-2008 09:13 PM
Lon
Jeep Mailing List
0
10-13-2005 10:33 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)