power windows control assembly
#11
Guest
Posts: n/a
Re: power windows control assembly
billy ray wrote:
> REMOVAL
>
> (1) Disconnect and isolate the battery negative
>
> cable.
>
> (2) Remove the trim panel from the inside of the
>
> front door. (Refer to 23 - BODY/DOOR - FRONT/
>
> TRIM PANEL - REMOVAL).
>
> (3) Disconnect the door wire harness connectors
>
> from the door module connector receptacles.
>
> (4) Remove the three screws that secure the door
>
> module to the front door trim panel (Fig. 8).
Thank-you Billy Ray..
It worked great!!
Do I need the whole assembly for the lock-out switch malfunction??
Would a bypass work??
Does anyone know a good deal on a new assembly??
Thank-you again!!
Jim
>
> (5) Remove the door module from the front door
>
> trim panel.
>
> INSTALLATION
>
> (1) Position the door module onto the front door
>
> trim panel.
>
> (2) Install and tighten the three screws that secure
>
> the door module to the front door trim panel. Tighten
>
> the screws to 2.2 N·m (20 in. lbs.).
>
> (3) Reconnect the door wire harness connectors to
>
> the door module connector receptacles.
>
> (4) Reinstall the trim panel onto the front door
>
> inner panel. (Refer to 23 - BODY/DOOR - FRONT/
>
> TRIM PANEL - INSTALLATION).
>
> (5) Reconnect the battery negative cable.
>
> "jim" <piglet80917@netscape.net> wrote in message
> news:1153848980.179220.157110@i3g2000cwc.googlegro ups.com...
> >I need HELP!!
> > My 2000 cherokee limited has a problem in the drivers armrest control
> > assembly.
> > My Haynes manual states that I should "pry out" the assembly and unplug
> > it.
> > I have tried this and cannot seem to get the assembly all the way out.
> > Can you help me on this??
> > Thank-you
> > Jim
> >
#12
Guest
Posts: n/a
Re: power windows control assembly
billy ray wrote:
> REMOVAL
>
> (1) Disconnect and isolate the battery negative
>
> cable.
>
> (2) Remove the trim panel from the inside of the
>
> front door. (Refer to 23 - BODY/DOOR - FRONT/
>
> TRIM PANEL - REMOVAL).
>
> (3) Disconnect the door wire harness connectors
>
> from the door module connector receptacles.
>
> (4) Remove the three screws that secure the door
>
> module to the front door trim panel (Fig. 8).
Thank-you Billy Ray..
It worked great!!
Do I need the whole assembly for the lock-out switch malfunction??
Would a bypass work??
Does anyone know a good deal on a new assembly??
Thank-you again!!
Jim
>
> (5) Remove the door module from the front door
>
> trim panel.
>
> INSTALLATION
>
> (1) Position the door module onto the front door
>
> trim panel.
>
> (2) Install and tighten the three screws that secure
>
> the door module to the front door trim panel. Tighten
>
> the screws to 2.2 N·m (20 in. lbs.).
>
> (3) Reconnect the door wire harness connectors to
>
> the door module connector receptacles.
>
> (4) Reinstall the trim panel onto the front door
>
> inner panel. (Refer to 23 - BODY/DOOR - FRONT/
>
> TRIM PANEL - INSTALLATION).
>
> (5) Reconnect the battery negative cable.
>
> "jim" <piglet80917@netscape.net> wrote in message
> news:1153848980.179220.157110@i3g2000cwc.googlegro ups.com...
> >I need HELP!!
> > My 2000 cherokee limited has a problem in the drivers armrest control
> > assembly.
> > My Haynes manual states that I should "pry out" the assembly and unplug
> > it.
> > I have tried this and cannot seem to get the assembly all the way out.
> > Can you help me on this??
> > Thank-you
> > Jim
> >
#13
Guest
Posts: n/a
Re: power windows control assembly
billy ray wrote:
> REMOVAL
>
> (1) Disconnect and isolate the battery negative
>
> cable.
>
> (2) Remove the trim panel from the inside of the
>
> front door. (Refer to 23 - BODY/DOOR - FRONT/
>
> TRIM PANEL - REMOVAL).
>
> (3) Disconnect the door wire harness connectors
>
> from the door module connector receptacles.
>
> (4) Remove the three screws that secure the door
>
> module to the front door trim panel (Fig. 8).
Thank-you Billy Ray..
It worked great!!
Do I need the whole assembly for the lock-out switch malfunction??
Would a bypass work??
Does anyone know a good deal on a new assembly??
Thank-you again!!
Jim
>
> (5) Remove the door module from the front door
>
> trim panel.
>
> INSTALLATION
>
> (1) Position the door module onto the front door
>
> trim panel.
>
> (2) Install and tighten the three screws that secure
>
> the door module to the front door trim panel. Tighten
>
> the screws to 2.2 N·m (20 in. lbs.).
>
> (3) Reconnect the door wire harness connectors to
>
> the door module connector receptacles.
>
> (4) Reinstall the trim panel onto the front door
>
> inner panel. (Refer to 23 - BODY/DOOR - FRONT/
>
> TRIM PANEL - INSTALLATION).
>
> (5) Reconnect the battery negative cable.
>
> "jim" <piglet80917@netscape.net> wrote in message
> news:1153848980.179220.157110@i3g2000cwc.googlegro ups.com...
> >I need HELP!!
> > My 2000 cherokee limited has a problem in the drivers armrest control
> > assembly.
> > My Haynes manual states that I should "pry out" the assembly and unplug
> > it.
> > I have tried this and cannot seem to get the assembly all the way out.
> > Can you help me on this??
> > Thank-you
> > Jim
> >
Thread
Thread Starter
Forum
Replies
Last Post
Chris
Jeep Mailing List
178
10-05-2003 07:00 PM
William Oliveri
Jeep Mailing List
10
08-26-2003 09:28 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)