Pinion Seal
Guest
Posts: n/a
Re: Pinion Seal
Thank you Bill and Steve. I have Friday off so I will try it again.
Eric
"L.W. (ßill) ------ III" <----------@***.net> wrote in message
news:413776EC.EDE7E55A@***.net...
> Hi Eric,
> This is the combination I use:
> http://www.----------.com/pipewrench.jpg A two foot pipe wrench, and a
> forged "L" without the little ball that's designed to hold the socket,
> that weakens it. It's only about a foot long, so I use the bottle jack
> handle to feather the floor jack handle cheaters. Use your breaker bar
> if you want a nice shinny new one.
> God Bless America, ßill O|||||||O
> mailto:--------------------
> Eric Shade wrote:
> >
> > Replacing the rear pinion seal in an 85 cherokee pioneer Dana 35.
Problem
> > is I cannot get the shaft nut off the yoke. My question is, what is
the
> > torque spec on this thing? Been try to spray it down with PB blaster
and
> > been hanging off my breaker bar trying to loosen it to no avail. Any
advice
> > would be appreciated.
> >
> > Eric Shade
Eric
"L.W. (ßill) ------ III" <----------@***.net> wrote in message
news:413776EC.EDE7E55A@***.net...
> Hi Eric,
> This is the combination I use:
> http://www.----------.com/pipewrench.jpg A two foot pipe wrench, and a
> forged "L" without the little ball that's designed to hold the socket,
> that weakens it. It's only about a foot long, so I use the bottle jack
> handle to feather the floor jack handle cheaters. Use your breaker bar
> if you want a nice shinny new one.
> God Bless America, ßill O|||||||O
> mailto:--------------------
> Eric Shade wrote:
> >
> > Replacing the rear pinion seal in an 85 cherokee pioneer Dana 35.
Problem
> > is I cannot get the shaft nut off the yoke. My question is, what is
the
> > torque spec on this thing? Been try to spray it down with PB blaster
and
> > been hanging off my breaker bar trying to loosen it to no avail. Any
advice
> > would be appreciated.
> >
> > Eric Shade
Guest
Posts: n/a
Re: Pinion Seal
Thank you Bill and Steve. I have Friday off so I will try it again.
Eric
"L.W. (ßill) ------ III" <----------@***.net> wrote in message
news:413776EC.EDE7E55A@***.net...
> Hi Eric,
> This is the combination I use:
> http://www.----------.com/pipewrench.jpg A two foot pipe wrench, and a
> forged "L" without the little ball that's designed to hold the socket,
> that weakens it. It's only about a foot long, so I use the bottle jack
> handle to feather the floor jack handle cheaters. Use your breaker bar
> if you want a nice shinny new one.
> God Bless America, ßill O|||||||O
> mailto:--------------------
> Eric Shade wrote:
> >
> > Replacing the rear pinion seal in an 85 cherokee pioneer Dana 35.
Problem
> > is I cannot get the shaft nut off the yoke. My question is, what is
the
> > torque spec on this thing? Been try to spray it down with PB blaster
and
> > been hanging off my breaker bar trying to loosen it to no avail. Any
advice
> > would be appreciated.
> >
> > Eric Shade
Eric
"L.W. (ßill) ------ III" <----------@***.net> wrote in message
news:413776EC.EDE7E55A@***.net...
> Hi Eric,
> This is the combination I use:
> http://www.----------.com/pipewrench.jpg A two foot pipe wrench, and a
> forged "L" without the little ball that's designed to hold the socket,
> that weakens it. It's only about a foot long, so I use the bottle jack
> handle to feather the floor jack handle cheaters. Use your breaker bar
> if you want a nice shinny new one.
> God Bless America, ßill O|||||||O
> mailto:--------------------
> Eric Shade wrote:
> >
> > Replacing the rear pinion seal in an 85 cherokee pioneer Dana 35.
Problem
> > is I cannot get the shaft nut off the yoke. My question is, what is
the
> > torque spec on this thing? Been try to spray it down with PB blaster
and
> > been hanging off my breaker bar trying to loosen it to no avail. Any
advice
> > would be appreciated.
> >
> > Eric Shade
Guest
Posts: n/a
Re: Pinion Seal
Thank you Bill and Steve. I have Friday off so I will try it again.
Eric
"L.W. (ßill) ------ III" <----------@***.net> wrote in message
news:413776EC.EDE7E55A@***.net...
> Hi Eric,
> This is the combination I use:
> http://www.----------.com/pipewrench.jpg A two foot pipe wrench, and a
> forged "L" without the little ball that's designed to hold the socket,
> that weakens it. It's only about a foot long, so I use the bottle jack
> handle to feather the floor jack handle cheaters. Use your breaker bar
> if you want a nice shinny new one.
> God Bless America, ßill O|||||||O
> mailto:--------------------
> Eric Shade wrote:
> >
> > Replacing the rear pinion seal in an 85 cherokee pioneer Dana 35.
Problem
> > is I cannot get the shaft nut off the yoke. My question is, what is
the
> > torque spec on this thing? Been try to spray it down with PB blaster
and
> > been hanging off my breaker bar trying to loosen it to no avail. Any
advice
> > would be appreciated.
> >
> > Eric Shade
Eric
"L.W. (ßill) ------ III" <----------@***.net> wrote in message
news:413776EC.EDE7E55A@***.net...
> Hi Eric,
> This is the combination I use:
> http://www.----------.com/pipewrench.jpg A two foot pipe wrench, and a
> forged "L" without the little ball that's designed to hold the socket,
> that weakens it. It's only about a foot long, so I use the bottle jack
> handle to feather the floor jack handle cheaters. Use your breaker bar
> if you want a nice shinny new one.
> God Bless America, ßill O|||||||O
> mailto:--------------------
> Eric Shade wrote:
> >
> > Replacing the rear pinion seal in an 85 cherokee pioneer Dana 35.
Problem
> > is I cannot get the shaft nut off the yoke. My question is, what is
the
> > torque spec on this thing? Been try to spray it down with PB blaster
and
> > been hanging off my breaker bar trying to loosen it to no avail. Any
advice
> > would be appreciated.
> >
> > Eric Shade
Thread
Thread Starter
Forum
Replies
Last Post
Paul Tremblay
Jeep Mailing List
0
Jul 28, 2004 10:17 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
