((OT)) Electronics (electrical) Problem
#141
Guest
Posts: n/a
Re: Re: ((OT)) Electronics (electrical) Problem = SnoMan the Stalker!
On Wed, 30 May 2007 20:30:45 -0400, Mike Romain <romainm@sympatico.ca>
wrote:
>Listen you insane lying brain dead stalker twerp, 'his' light box is in
>a planter and the one I did is behind the 220 panel for the pool motors
>sitting right below the light box.
Such a child, I do not carr where bulb is. There is a reason for code
and why there as codes for using lower voltages unless you get wannabe
smart guys like you that decides that code does not mean squat and
changes it. It is bad enough you do this to your own stuff but to do
it to others and tell others to do it to show a real desrepect for
safety codes.
>
>The light box is a 120V unit with the spin motor running on line voltage
>and a stepdown transformer to give the 'light' only 12 or 24 volts.
There is a difference between a motor that delevopes no voltage output
and transformered curcuit. Maybe everyone else that designs this stuff
and their safty codes is full of it and you should take over for them
huh?
>
>Now once again go screw yourself!
If is so much fun to watch you screw yourself MIke. You are your own
worst enemy sometimes.
>
>Internet Stalkers are not cool these days as mentioned before or 'Why
>Lord can't I at least get a halfway intelligent stalker not some brain
>dead -------'????
Again it is funny to watch your comments sometimes as you act like a
child
>
>Mike
>86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
>88 Cherokee 235 BFG AT's
>Canadian Off Road Trips Photos: Non members can still view!
Typical ego signature and serves no purpose other than to try to feed
ego. BTW you left of your 5 speed with 4 usable gears because of your
tall ratio "power" gears you use with big tires. (I guess this is why
you got in a bit of a twist over low range usage a while back
becaause you have never had a properly geared 4x4 that did not require
frequent use of it and just could not understand why anyone would not
need to use it often like you have too.)
-----------------
TheSnoMan.com
wrote:
>Listen you insane lying brain dead stalker twerp, 'his' light box is in
>a planter and the one I did is behind the 220 panel for the pool motors
>sitting right below the light box.
Such a child, I do not carr where bulb is. There is a reason for code
and why there as codes for using lower voltages unless you get wannabe
smart guys like you that decides that code does not mean squat and
changes it. It is bad enough you do this to your own stuff but to do
it to others and tell others to do it to show a real desrepect for
safety codes.
>
>The light box is a 120V unit with the spin motor running on line voltage
>and a stepdown transformer to give the 'light' only 12 or 24 volts.
There is a difference between a motor that delevopes no voltage output
and transformered curcuit. Maybe everyone else that designs this stuff
and their safty codes is full of it and you should take over for them
huh?
>
>Now once again go screw yourself!
If is so much fun to watch you screw yourself MIke. You are your own
worst enemy sometimes.
>
>Internet Stalkers are not cool these days as mentioned before or 'Why
>Lord can't I at least get a halfway intelligent stalker not some brain
>dead -------'????
Again it is funny to watch your comments sometimes as you act like a
child
>
>Mike
>86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
>88 Cherokee 235 BFG AT's
>Canadian Off Road Trips Photos: Non members can still view!
Typical ego signature and serves no purpose other than to try to feed
ego. BTW you left of your 5 speed with 4 usable gears because of your
tall ratio "power" gears you use with big tires. (I guess this is why
you got in a bit of a twist over low range usage a while back
becaause you have never had a properly geared 4x4 that did not require
frequent use of it and just could not understand why anyone would not
need to use it often like you have too.)
-----------------
TheSnoMan.com
#142
Guest
Posts: n/a
Re: ((OT)) Electronics (electrical) Problem = SnoMan the lying Stalker!
SnoMan wrote:
> On Wed, 30 May 2007 20:30:45 -0400, Mike Romain <romainm@sympatico.ca>
> wrote:
>
>> Listen you insane lying brain dead stalker twerp, 'his' light box is in
>> a planter and the one I did is behind the 220 panel for the pool motors
>> sitting right below the light box.
>
> Such a child, I do not carr where bulb is. There is a reason for code
> and why there as codes for using lower voltages unless you get wannabe
> smart guys like you that decides that code does not mean squat and
> changes it. It is bad enough you do this to your own stuff but to do
> it to others and tell others to do it to show a real desrepect for
> safety codes.
LIAR!
The fiber optic light boxes have a full 120 volts going into them, there
is 'no' building code that prohibits that at all. Yes, I 'do' know this
for a fact, it is my job to know.
Once again you have proven yourself a liar and a Stalking idiot just
full of --------.
And seeing as you 'do' want to play, how would you like me to do a
collection of all your total -------- and life threatening advise and
add 'that' to every one of your posts for ya.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
> On Wed, 30 May 2007 20:30:45 -0400, Mike Romain <romainm@sympatico.ca>
> wrote:
>
>> Listen you insane lying brain dead stalker twerp, 'his' light box is in
>> a planter and the one I did is behind the 220 panel for the pool motors
>> sitting right below the light box.
>
> Such a child, I do not carr where bulb is. There is a reason for code
> and why there as codes for using lower voltages unless you get wannabe
> smart guys like you that decides that code does not mean squat and
> changes it. It is bad enough you do this to your own stuff but to do
> it to others and tell others to do it to show a real desrepect for
> safety codes.
LIAR!
The fiber optic light boxes have a full 120 volts going into them, there
is 'no' building code that prohibits that at all. Yes, I 'do' know this
for a fact, it is my job to know.
Once again you have proven yourself a liar and a Stalking idiot just
full of --------.
And seeing as you 'do' want to play, how would you like me to do a
collection of all your total -------- and life threatening advise and
add 'that' to every one of your posts for ya.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
#143
Guest
Posts: n/a
Re: ((OT)) Electronics (electrical) Problem = SnoMan the lying Stalker!
SnoMan wrote:
> On Wed, 30 May 2007 20:30:45 -0400, Mike Romain <romainm@sympatico.ca>
> wrote:
>
>> Listen you insane lying brain dead stalker twerp, 'his' light box is in
>> a planter and the one I did is behind the 220 panel for the pool motors
>> sitting right below the light box.
>
> Such a child, I do not carr where bulb is. There is a reason for code
> and why there as codes for using lower voltages unless you get wannabe
> smart guys like you that decides that code does not mean squat and
> changes it. It is bad enough you do this to your own stuff but to do
> it to others and tell others to do it to show a real desrepect for
> safety codes.
LIAR!
The fiber optic light boxes have a full 120 volts going into them, there
is 'no' building code that prohibits that at all. Yes, I 'do' know this
for a fact, it is my job to know.
Once again you have proven yourself a liar and a Stalking idiot just
full of --------.
And seeing as you 'do' want to play, how would you like me to do a
collection of all your total -------- and life threatening advise and
add 'that' to every one of your posts for ya.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
> On Wed, 30 May 2007 20:30:45 -0400, Mike Romain <romainm@sympatico.ca>
> wrote:
>
>> Listen you insane lying brain dead stalker twerp, 'his' light box is in
>> a planter and the one I did is behind the 220 panel for the pool motors
>> sitting right below the light box.
>
> Such a child, I do not carr where bulb is. There is a reason for code
> and why there as codes for using lower voltages unless you get wannabe
> smart guys like you that decides that code does not mean squat and
> changes it. It is bad enough you do this to your own stuff but to do
> it to others and tell others to do it to show a real desrepect for
> safety codes.
LIAR!
The fiber optic light boxes have a full 120 volts going into them, there
is 'no' building code that prohibits that at all. Yes, I 'do' know this
for a fact, it is my job to know.
Once again you have proven yourself a liar and a Stalking idiot just
full of --------.
And seeing as you 'do' want to play, how would you like me to do a
collection of all your total -------- and life threatening advise and
add 'that' to every one of your posts for ya.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
#144
Guest
Posts: n/a
Re: ((OT)) Electronics (electrical) Problem = SnoMan the lying Stalker!
SnoMan wrote:
> On Wed, 30 May 2007 20:30:45 -0400, Mike Romain <romainm@sympatico.ca>
> wrote:
>
>> Listen you insane lying brain dead stalker twerp, 'his' light box is in
>> a planter and the one I did is behind the 220 panel for the pool motors
>> sitting right below the light box.
>
> Such a child, I do not carr where bulb is. There is a reason for code
> and why there as codes for using lower voltages unless you get wannabe
> smart guys like you that decides that code does not mean squat and
> changes it. It is bad enough you do this to your own stuff but to do
> it to others and tell others to do it to show a real desrepect for
> safety codes.
LIAR!
The fiber optic light boxes have a full 120 volts going into them, there
is 'no' building code that prohibits that at all. Yes, I 'do' know this
for a fact, it is my job to know.
Once again you have proven yourself a liar and a Stalking idiot just
full of --------.
And seeing as you 'do' want to play, how would you like me to do a
collection of all your total -------- and life threatening advise and
add 'that' to every one of your posts for ya.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
> On Wed, 30 May 2007 20:30:45 -0400, Mike Romain <romainm@sympatico.ca>
> wrote:
>
>> Listen you insane lying brain dead stalker twerp, 'his' light box is in
>> a planter and the one I did is behind the 220 panel for the pool motors
>> sitting right below the light box.
>
> Such a child, I do not carr where bulb is. There is a reason for code
> and why there as codes for using lower voltages unless you get wannabe
> smart guys like you that decides that code does not mean squat and
> changes it. It is bad enough you do this to your own stuff but to do
> it to others and tell others to do it to show a real desrepect for
> safety codes.
LIAR!
The fiber optic light boxes have a full 120 volts going into them, there
is 'no' building code that prohibits that at all. Yes, I 'do' know this
for a fact, it is my job to know.
Once again you have proven yourself a liar and a Stalking idiot just
full of --------.
And seeing as you 'do' want to play, how would you like me to do a
collection of all your total -------- and life threatening advise and
add 'that' to every one of your posts for ya.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
#145
Guest
Posts: n/a
Re: ((OT)) Electronics (electrical) Problem = SnoMan the lying Stalker!
SnoMan wrote:
> On Wed, 30 May 2007 20:30:45 -0400, Mike Romain <romainm@sympatico.ca>
> wrote:
>
>> Listen you insane lying brain dead stalker twerp, 'his' light box is in
>> a planter and the one I did is behind the 220 panel for the pool motors
>> sitting right below the light box.
>
> Such a child, I do not carr where bulb is. There is a reason for code
> and why there as codes for using lower voltages unless you get wannabe
> smart guys like you that decides that code does not mean squat and
> changes it. It is bad enough you do this to your own stuff but to do
> it to others and tell others to do it to show a real desrepect for
> safety codes.
LIAR!
The fiber optic light boxes have a full 120 volts going into them, there
is 'no' building code that prohibits that at all. Yes, I 'do' know this
for a fact, it is my job to know.
Once again you have proven yourself a liar and a Stalking idiot just
full of --------.
And seeing as you 'do' want to play, how would you like me to do a
collection of all your total -------- and life threatening advise and
add 'that' to every one of your posts for ya.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
> On Wed, 30 May 2007 20:30:45 -0400, Mike Romain <romainm@sympatico.ca>
> wrote:
>
>> Listen you insane lying brain dead stalker twerp, 'his' light box is in
>> a planter and the one I did is behind the 220 panel for the pool motors
>> sitting right below the light box.
>
> Such a child, I do not carr where bulb is. There is a reason for code
> and why there as codes for using lower voltages unless you get wannabe
> smart guys like you that decides that code does not mean squat and
> changes it. It is bad enough you do this to your own stuff but to do
> it to others and tell others to do it to show a real desrepect for
> safety codes.
LIAR!
The fiber optic light boxes have a full 120 volts going into them, there
is 'no' building code that prohibits that at all. Yes, I 'do' know this
for a fact, it is my job to know.
Once again you have proven yourself a liar and a Stalking idiot just
full of --------.
And seeing as you 'do' want to play, how would you like me to do a
collection of all your total -------- and life threatening advise and
add 'that' to every one of your posts for ya.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
#146
Guest
Posts: n/a
Re: ((OT)) Electronics (electrical) Problem
On Wed, 30 May 2007, Jeff Strickland wrote:
[snip]
>
> Where I got sideways is that the filiment LOOKS okay, so I checked it with my
> meter and it checked good too. As I explained in another post, I either
> operated my meter wrong, or it's broken. (I'm inclined to go with "wrong" for
> now. Don't ask ... )
This has happened to me and I work with lights for a living. Here's what
could have happened: The filament broke near the connection point. When
you put your meter on it the fliament flopped back into place and the
meter showed continuity. When you put it back into the socket it didn't
work -- either because the motion opened up the gap again or because the
heat generated when you aplied voltage expanded the metal and opened up
the gap. It tests OK, your meter works, but the bulb is bad. I've even
seen sparks jumping across the gap wen you apply power to globes like
that.
A related error can happen with cartridge fuses -- they can blow and still
carry the milliamp or so of current that the meter puts out, so they test
OK. But there's not enough conducting material there to carry real
current and under load you have an open circuit.
--
"We began to realize, as we plowed on with the destruction of New Jersey,
that the extent of our American lunatic fringe had been underestimated."
Orson Wells on the reaction to the _War Of The Worlds_ broadcast.
[snip]
>
> Where I got sideways is that the filiment LOOKS okay, so I checked it with my
> meter and it checked good too. As I explained in another post, I either
> operated my meter wrong, or it's broken. (I'm inclined to go with "wrong" for
> now. Don't ask ... )
This has happened to me and I work with lights for a living. Here's what
could have happened: The filament broke near the connection point. When
you put your meter on it the fliament flopped back into place and the
meter showed continuity. When you put it back into the socket it didn't
work -- either because the motion opened up the gap again or because the
heat generated when you aplied voltage expanded the metal and opened up
the gap. It tests OK, your meter works, but the bulb is bad. I've even
seen sparks jumping across the gap wen you apply power to globes like
that.
A related error can happen with cartridge fuses -- they can blow and still
carry the milliamp or so of current that the meter puts out, so they test
OK. But there's not enough conducting material there to carry real
current and under load you have an open circuit.
--
"We began to realize, as we plowed on with the destruction of New Jersey,
that the extent of our American lunatic fringe had been underestimated."
Orson Wells on the reaction to the _War Of The Worlds_ broadcast.
#147
Guest
Posts: n/a
Re: ((OT)) Electronics (electrical) Problem
On Wed, 30 May 2007, Jeff Strickland wrote:
[snip]
>
> Where I got sideways is that the filiment LOOKS okay, so I checked it with my
> meter and it checked good too. As I explained in another post, I either
> operated my meter wrong, or it's broken. (I'm inclined to go with "wrong" for
> now. Don't ask ... )
This has happened to me and I work with lights for a living. Here's what
could have happened: The filament broke near the connection point. When
you put your meter on it the fliament flopped back into place and the
meter showed continuity. When you put it back into the socket it didn't
work -- either because the motion opened up the gap again or because the
heat generated when you aplied voltage expanded the metal and opened up
the gap. It tests OK, your meter works, but the bulb is bad. I've even
seen sparks jumping across the gap wen you apply power to globes like
that.
A related error can happen with cartridge fuses -- they can blow and still
carry the milliamp or so of current that the meter puts out, so they test
OK. But there's not enough conducting material there to carry real
current and under load you have an open circuit.
--
"We began to realize, as we plowed on with the destruction of New Jersey,
that the extent of our American lunatic fringe had been underestimated."
Orson Wells on the reaction to the _War Of The Worlds_ broadcast.
[snip]
>
> Where I got sideways is that the filiment LOOKS okay, so I checked it with my
> meter and it checked good too. As I explained in another post, I either
> operated my meter wrong, or it's broken. (I'm inclined to go with "wrong" for
> now. Don't ask ... )
This has happened to me and I work with lights for a living. Here's what
could have happened: The filament broke near the connection point. When
you put your meter on it the fliament flopped back into place and the
meter showed continuity. When you put it back into the socket it didn't
work -- either because the motion opened up the gap again or because the
heat generated when you aplied voltage expanded the metal and opened up
the gap. It tests OK, your meter works, but the bulb is bad. I've even
seen sparks jumping across the gap wen you apply power to globes like
that.
A related error can happen with cartridge fuses -- they can blow and still
carry the milliamp or so of current that the meter puts out, so they test
OK. But there's not enough conducting material there to carry real
current and under load you have an open circuit.
--
"We began to realize, as we plowed on with the destruction of New Jersey,
that the extent of our American lunatic fringe had been underestimated."
Orson Wells on the reaction to the _War Of The Worlds_ broadcast.
#148
Guest
Posts: n/a
Re: ((OT)) Electronics (electrical) Problem
On Wed, 30 May 2007, Jeff Strickland wrote:
[snip]
>
> Where I got sideways is that the filiment LOOKS okay, so I checked it with my
> meter and it checked good too. As I explained in another post, I either
> operated my meter wrong, or it's broken. (I'm inclined to go with "wrong" for
> now. Don't ask ... )
This has happened to me and I work with lights for a living. Here's what
could have happened: The filament broke near the connection point. When
you put your meter on it the fliament flopped back into place and the
meter showed continuity. When you put it back into the socket it didn't
work -- either because the motion opened up the gap again or because the
heat generated when you aplied voltage expanded the metal and opened up
the gap. It tests OK, your meter works, but the bulb is bad. I've even
seen sparks jumping across the gap wen you apply power to globes like
that.
A related error can happen with cartridge fuses -- they can blow and still
carry the milliamp or so of current that the meter puts out, so they test
OK. But there's not enough conducting material there to carry real
current and under load you have an open circuit.
--
"We began to realize, as we plowed on with the destruction of New Jersey,
that the extent of our American lunatic fringe had been underestimated."
Orson Wells on the reaction to the _War Of The Worlds_ broadcast.
[snip]
>
> Where I got sideways is that the filiment LOOKS okay, so I checked it with my
> meter and it checked good too. As I explained in another post, I either
> operated my meter wrong, or it's broken. (I'm inclined to go with "wrong" for
> now. Don't ask ... )
This has happened to me and I work with lights for a living. Here's what
could have happened: The filament broke near the connection point. When
you put your meter on it the fliament flopped back into place and the
meter showed continuity. When you put it back into the socket it didn't
work -- either because the motion opened up the gap again or because the
heat generated when you aplied voltage expanded the metal and opened up
the gap. It tests OK, your meter works, but the bulb is bad. I've even
seen sparks jumping across the gap wen you apply power to globes like
that.
A related error can happen with cartridge fuses -- they can blow and still
carry the milliamp or so of current that the meter puts out, so they test
OK. But there's not enough conducting material there to carry real
current and under load you have an open circuit.
--
"We began to realize, as we plowed on with the destruction of New Jersey,
that the extent of our American lunatic fringe had been underestimated."
Orson Wells on the reaction to the _War Of The Worlds_ broadcast.
#149
Guest
Posts: n/a
Re: ((OT)) Electronics (electrical) Problem
On Wed, 30 May 2007, Jeff Strickland wrote:
[snip]
>
> Where I got sideways is that the filiment LOOKS okay, so I checked it with my
> meter and it checked good too. As I explained in another post, I either
> operated my meter wrong, or it's broken. (I'm inclined to go with "wrong" for
> now. Don't ask ... )
This has happened to me and I work with lights for a living. Here's what
could have happened: The filament broke near the connection point. When
you put your meter on it the fliament flopped back into place and the
meter showed continuity. When you put it back into the socket it didn't
work -- either because the motion opened up the gap again or because the
heat generated when you aplied voltage expanded the metal and opened up
the gap. It tests OK, your meter works, but the bulb is bad. I've even
seen sparks jumping across the gap wen you apply power to globes like
that.
A related error can happen with cartridge fuses -- they can blow and still
carry the milliamp or so of current that the meter puts out, so they test
OK. But there's not enough conducting material there to carry real
current and under load you have an open circuit.
--
"We began to realize, as we plowed on with the destruction of New Jersey,
that the extent of our American lunatic fringe had been underestimated."
Orson Wells on the reaction to the _War Of The Worlds_ broadcast.
[snip]
>
> Where I got sideways is that the filiment LOOKS okay, so I checked it with my
> meter and it checked good too. As I explained in another post, I either
> operated my meter wrong, or it's broken. (I'm inclined to go with "wrong" for
> now. Don't ask ... )
This has happened to me and I work with lights for a living. Here's what
could have happened: The filament broke near the connection point. When
you put your meter on it the fliament flopped back into place and the
meter showed continuity. When you put it back into the socket it didn't
work -- either because the motion opened up the gap again or because the
heat generated when you aplied voltage expanded the metal and opened up
the gap. It tests OK, your meter works, but the bulb is bad. I've even
seen sparks jumping across the gap wen you apply power to globes like
that.
A related error can happen with cartridge fuses -- they can blow and still
carry the milliamp or so of current that the meter puts out, so they test
OK. But there's not enough conducting material there to carry real
current and under load you have an open circuit.
--
"We began to realize, as we plowed on with the destruction of New Jersey,
that the extent of our American lunatic fringe had been underestimated."
Orson Wells on the reaction to the _War Of The Worlds_ broadcast.
#150
Guest
Posts: n/a
Re: ((OT)) Electronics (electrical) Problem = SnoMan the lying Stalker!
I'll say again, Bloman, ALL of my pool lighting is 120V, professionally
installed, passed inspection and conforms with code.
No electrical code forbids full line voltage in wet areas or requires
low-voltage circuits in wet areas instead of line voltage. If it did, my
pool pumps would operate on 12 volts and require twenty times as much
current as they do now, which would be very dangerous. Code provides for the
wet areas by requiring GFCI's and conduit rated for wet areas.
Time to re-join the real world and leave this fantasy world you live in
where you are always right and anyone that disagrees with you is wrong.
Yes, you are now in my killfile, but you are so spectacularly wrong on your
assumption (that you present as fact) that code requires low-voltage wiring
for pools, I had to respond.
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:465ed82f$0$10513$9a6e19ea@unlimited.newshosti ng.com...
> SnoMan wrote:
>> On Wed, 30 May 2007 20:30:45 -0400, Mike Romain <romainm@sympatico.ca>
>> wrote:
>>
>>> Listen you insane lying brain dead stalker twerp, 'his' light box is in
>>> a planter and the one I did is behind the 220 panel for the pool motors
>>> sitting right below the light box.
>>
>> Such a child, I do not carr where bulb is. There is a reason for code
>> and why there as codes for using lower voltages unless you get wannabe
>> smart guys like you that decides that code does not mean squat and
>> changes it. It is bad enough you do this to your own stuff but to do
>> it to others and tell others to do it to show a real desrepect for
>> safety codes.
>
> LIAR!
>
> The fiber optic light boxes have a full 120 volts going into them, there
> is 'no' building code that prohibits that at all. Yes, I 'do' know this
> for a fact, it is my job to know.
>
> Once again you have proven yourself a liar and a Stalking idiot just full
> of --------.
>
> And seeing as you 'do' want to play, how would you like me to do a
> collection of all your total -------- and life threatening advise and add
> 'that' to every one of your posts for ya.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> (More Off Road album links at bottom of the view page)
installed, passed inspection and conforms with code.
No electrical code forbids full line voltage in wet areas or requires
low-voltage circuits in wet areas instead of line voltage. If it did, my
pool pumps would operate on 12 volts and require twenty times as much
current as they do now, which would be very dangerous. Code provides for the
wet areas by requiring GFCI's and conduit rated for wet areas.
Time to re-join the real world and leave this fantasy world you live in
where you are always right and anyone that disagrees with you is wrong.
Yes, you are now in my killfile, but you are so spectacularly wrong on your
assumption (that you present as fact) that code requires low-voltage wiring
for pools, I had to respond.
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:465ed82f$0$10513$9a6e19ea@unlimited.newshosti ng.com...
> SnoMan wrote:
>> On Wed, 30 May 2007 20:30:45 -0400, Mike Romain <romainm@sympatico.ca>
>> wrote:
>>
>>> Listen you insane lying brain dead stalker twerp, 'his' light box is in
>>> a planter and the one I did is behind the 220 panel for the pool motors
>>> sitting right below the light box.
>>
>> Such a child, I do not carr where bulb is. There is a reason for code
>> and why there as codes for using lower voltages unless you get wannabe
>> smart guys like you that decides that code does not mean squat and
>> changes it. It is bad enough you do this to your own stuff but to do
>> it to others and tell others to do it to show a real desrepect for
>> safety codes.
>
> LIAR!
>
> The fiber optic light boxes have a full 120 volts going into them, there
> is 'no' building code that prohibits that at all. Yes, I 'do' know this
> for a fact, it is my job to know.
>
> Once again you have proven yourself a liar and a Stalking idiot just full
> of --------.
>
> And seeing as you 'do' want to play, how would you like me to do a
> collection of all your total -------- and life threatening advise and add
> 'that' to every one of your posts for ya.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> (More Off Road album links at bottom of the view page)