Oil Sender Unit location 2000 Jeep Cherokee Sport
#1
Guest
Posts: n/a
Oil Sender Unit location 2000 Jeep Cherokee Sport
The oil pressure gauge recently went to 80 one morning and has consistently stayed there. I had my oil changed to see if this would help but hasn't. The vehicle is running fine, but the pressure is at 80??? This has never happened, has always been around 40-50, then shot up to 80 and stayed. From what I have heard that the sender unit failed???? If this sounds right, where is this unit located and is it easy to replace instead of going to a dealer
Thanks....
--
fladolphin
-----------------------------------------------------------------------
View this thread: http://www.carstalk.net/viewtopic-364593.htm
Send from http://www.carstalk.ne
#2
Guest
Posts: n/a
Re: Oil Sender Unit location 2000 Jeep Cherokee Sport
The sending unit is adjacent to the oil filter adapter...look for a sensor
with 2 wires on or near the oil filter adapter. Most likely you have a bad
sensor, but to double check plug a mechanical test gauge into the port and
check the pressure.
"fladolphin" <fladolphin.1z9386@no-mx.carstalk.net> wrote in message
news:fladolphin.1z9386@no-mx.carstalk.net...
>
> The oil pressure gauge recently went to 80 one morning and has
> consistently stayed there. I had my oil changed to see if this would help
> but hasn't. The vehicle is running fine, but the pressure is at 80???
> This has never happened, has always been around 40-50, then shot up to 80
> and stayed. From what I have heard that the sender unit failed???? If
> this sounds right, where is this unit located and is it easy to replace
> instead of going to a dealer?
>
> Thanks.....
>
>
> --
> fladolphin
>
> ------------------------------------------------------------------------
> View this thread: http://www.carstalk.net/viewtopic-364593.html
>
> Send from http://www.carstalk.net
>
with 2 wires on or near the oil filter adapter. Most likely you have a bad
sensor, but to double check plug a mechanical test gauge into the port and
check the pressure.
"fladolphin" <fladolphin.1z9386@no-mx.carstalk.net> wrote in message
news:fladolphin.1z9386@no-mx.carstalk.net...
>
> The oil pressure gauge recently went to 80 one morning and has
> consistently stayed there. I had my oil changed to see if this would help
> but hasn't. The vehicle is running fine, but the pressure is at 80???
> This has never happened, has always been around 40-50, then shot up to 80
> and stayed. From what I have heard that the sender unit failed???? If
> this sounds right, where is this unit located and is it easy to replace
> instead of going to a dealer?
>
> Thanks.....
>
>
> --
> fladolphin
>
> ------------------------------------------------------------------------
> View this thread: http://www.carstalk.net/viewtopic-364593.html
>
> Send from http://www.carstalk.net
>
#3
Guest
Posts: n/a
Re: Oil Sender Unit location 2000 Jeep Cherokee Sport
The sending unit is adjacent to the oil filter adapter...look for a sensor
with 2 wires on or near the oil filter adapter. Most likely you have a bad
sensor, but to double check plug a mechanical test gauge into the port and
check the pressure.
"fladolphin" <fladolphin.1z9386@no-mx.carstalk.net> wrote in message
news:fladolphin.1z9386@no-mx.carstalk.net...
>
> The oil pressure gauge recently went to 80 one morning and has
> consistently stayed there. I had my oil changed to see if this would help
> but hasn't. The vehicle is running fine, but the pressure is at 80???
> This has never happened, has always been around 40-50, then shot up to 80
> and stayed. From what I have heard that the sender unit failed???? If
> this sounds right, where is this unit located and is it easy to replace
> instead of going to a dealer?
>
> Thanks.....
>
>
> --
> fladolphin
>
> ------------------------------------------------------------------------
> View this thread: http://www.carstalk.net/viewtopic-364593.html
>
> Send from http://www.carstalk.net
>
with 2 wires on or near the oil filter adapter. Most likely you have a bad
sensor, but to double check plug a mechanical test gauge into the port and
check the pressure.
"fladolphin" <fladolphin.1z9386@no-mx.carstalk.net> wrote in message
news:fladolphin.1z9386@no-mx.carstalk.net...
>
> The oil pressure gauge recently went to 80 one morning and has
> consistently stayed there. I had my oil changed to see if this would help
> but hasn't. The vehicle is running fine, but the pressure is at 80???
> This has never happened, has always been around 40-50, then shot up to 80
> and stayed. From what I have heard that the sender unit failed???? If
> this sounds right, where is this unit located and is it easy to replace
> instead of going to a dealer?
>
> Thanks.....
>
>
> --
> fladolphin
>
> ------------------------------------------------------------------------
> View this thread: http://www.carstalk.net/viewtopic-364593.html
>
> Send from http://www.carstalk.net
>
#4
Guest
Posts: n/a
Re: Oil Sender Unit location 2000 Jeep Cherokee Sport
The sending unit is adjacent to the oil filter adapter...look for a sensor
with 2 wires on or near the oil filter adapter. Most likely you have a bad
sensor, but to double check plug a mechanical test gauge into the port and
check the pressure.
"fladolphin" <fladolphin.1z9386@no-mx.carstalk.net> wrote in message
news:fladolphin.1z9386@no-mx.carstalk.net...
>
> The oil pressure gauge recently went to 80 one morning and has
> consistently stayed there. I had my oil changed to see if this would help
> but hasn't. The vehicle is running fine, but the pressure is at 80???
> This has never happened, has always been around 40-50, then shot up to 80
> and stayed. From what I have heard that the sender unit failed???? If
> this sounds right, where is this unit located and is it easy to replace
> instead of going to a dealer?
>
> Thanks.....
>
>
> --
> fladolphin
>
> ------------------------------------------------------------------------
> View this thread: http://www.carstalk.net/viewtopic-364593.html
>
> Send from http://www.carstalk.net
>
with 2 wires on or near the oil filter adapter. Most likely you have a bad
sensor, but to double check plug a mechanical test gauge into the port and
check the pressure.
"fladolphin" <fladolphin.1z9386@no-mx.carstalk.net> wrote in message
news:fladolphin.1z9386@no-mx.carstalk.net...
>
> The oil pressure gauge recently went to 80 one morning and has
> consistently stayed there. I had my oil changed to see if this would help
> but hasn't. The vehicle is running fine, but the pressure is at 80???
> This has never happened, has always been around 40-50, then shot up to 80
> and stayed. From what I have heard that the sender unit failed???? If
> this sounds right, where is this unit located and is it easy to replace
> instead of going to a dealer?
>
> Thanks.....
>
>
> --
> fladolphin
>
> ------------------------------------------------------------------------
> View this thread: http://www.carstalk.net/viewtopic-364593.html
>
> Send from http://www.carstalk.net
>
#5
Guest
Posts: n/a
Re: Oil Sender Unit location 2000 Jeep Cherokee Sport
fladolphin did pass the time by typing:
> The oil pressure gauge recently went to 80 one morning and has consistently
> stayed there. I had my oil changed to see if this would help but hasn't.
> The vehicle is running fine, but the pressure is at 80??? This has never
> happened, has always been around 40-50, then shot up to 80 and stayed. From
> what I have heard that the sender unit failed???? If this sounds right,
> where is this unit located and is it easy to replace instead of going to a
> dealer?
But first put the sensor wire back on, it fell off. :)
http://members.***.net/wilsond/Fixes...l-pressure.jpg
on the I6 it's down on the block just above the oil filter.
Could be the sensor, it's easy to replace with simple hand tools
and NAPA has the part.
--
DougW
> The oil pressure gauge recently went to 80 one morning and has consistently
> stayed there. I had my oil changed to see if this would help but hasn't.
> The vehicle is running fine, but the pressure is at 80??? This has never
> happened, has always been around 40-50, then shot up to 80 and stayed. From
> what I have heard that the sender unit failed???? If this sounds right,
> where is this unit located and is it easy to replace instead of going to a
> dealer?
But first put the sensor wire back on, it fell off. :)
http://members.***.net/wilsond/Fixes...l-pressure.jpg
on the I6 it's down on the block just above the oil filter.
Could be the sensor, it's easy to replace with simple hand tools
and NAPA has the part.
--
DougW
#6
Guest
Posts: n/a
Re: Oil Sender Unit location 2000 Jeep Cherokee Sport
fladolphin did pass the time by typing:
> The oil pressure gauge recently went to 80 one morning and has consistently
> stayed there. I had my oil changed to see if this would help but hasn't.
> The vehicle is running fine, but the pressure is at 80??? This has never
> happened, has always been around 40-50, then shot up to 80 and stayed. From
> what I have heard that the sender unit failed???? If this sounds right,
> where is this unit located and is it easy to replace instead of going to a
> dealer?
But first put the sensor wire back on, it fell off. :)
http://members.***.net/wilsond/Fixes...l-pressure.jpg
on the I6 it's down on the block just above the oil filter.
Could be the sensor, it's easy to replace with simple hand tools
and NAPA has the part.
--
DougW
> The oil pressure gauge recently went to 80 one morning and has consistently
> stayed there. I had my oil changed to see if this would help but hasn't.
> The vehicle is running fine, but the pressure is at 80??? This has never
> happened, has always been around 40-50, then shot up to 80 and stayed. From
> what I have heard that the sender unit failed???? If this sounds right,
> where is this unit located and is it easy to replace instead of going to a
> dealer?
But first put the sensor wire back on, it fell off. :)
http://members.***.net/wilsond/Fixes...l-pressure.jpg
on the I6 it's down on the block just above the oil filter.
Could be the sensor, it's easy to replace with simple hand tools
and NAPA has the part.
--
DougW
#7
Guest
Posts: n/a
Re: Oil Sender Unit location 2000 Jeep Cherokee Sport
fladolphin did pass the time by typing:
> The oil pressure gauge recently went to 80 one morning and has consistently
> stayed there. I had my oil changed to see if this would help but hasn't.
> The vehicle is running fine, but the pressure is at 80??? This has never
> happened, has always been around 40-50, then shot up to 80 and stayed. From
> what I have heard that the sender unit failed???? If this sounds right,
> where is this unit located and is it easy to replace instead of going to a
> dealer?
But first put the sensor wire back on, it fell off. :)
http://members.***.net/wilsond/Fixes...l-pressure.jpg
on the I6 it's down on the block just above the oil filter.
Could be the sensor, it's easy to replace with simple hand tools
and NAPA has the part.
--
DougW
> The oil pressure gauge recently went to 80 one morning and has consistently
> stayed there. I had my oil changed to see if this would help but hasn't.
> The vehicle is running fine, but the pressure is at 80??? This has never
> happened, has always been around 40-50, then shot up to 80 and stayed. From
> what I have heard that the sender unit failed???? If this sounds right,
> where is this unit located and is it easy to replace instead of going to a
> dealer?
But first put the sensor wire back on, it fell off. :)
http://members.***.net/wilsond/Fixes...l-pressure.jpg
on the I6 it's down on the block just above the oil filter.
Could be the sensor, it's easy to replace with simple hand tools
and NAPA has the part.
--
DougW
#8
Guest
Posts: n/a
Re: Oil Sender Unit location 2000 Jeep Cherokee Sport
It is easy to change,and I got one aftermarket.
With the engine off and the key in the on position does it still peg?
If you disconnect the sensor wire and do this again does it peg or stay
at -0-.
My 00 Sport sometimes pegs and will remain there for the drive cycle.I
changed the sensor,it was not the cause on mine.
When mine pegs I turn the key to the acc. position then off 2 or 3 times and
then it works again for a while,some kind if short.
Please post how you corrected yours. Thanks
"DougW" <post.replies@invalid.address> wrote in message
news:t3Yif.44107$2k5.6724@dukeread09...
> fladolphin did pass the time by typing:
>> The oil pressure gauge recently went to 80 one morning and has
>> consistently
>> stayed there. I had my oil changed to see if this would help but hasn't.
>> The vehicle is running fine, but the pressure is at 80??? This has never
>> happened, has always been around 40-50, then shot up to 80 and stayed.
>> From
>> what I have heard that the sender unit failed???? If this sounds right,
>> where is this unit located and is it easy to replace instead of going to
>> a
>> dealer?
>
> But first put the sensor wire back on, it fell off. :)
>
> http://members.***.net/wilsond/Fixes...l-pressure.jpg
> on the I6 it's down on the block just above the oil filter.
>
> Could be the sensor, it's easy to replace with simple hand tools
> and NAPA has the part.
>
> --
> DougW
>
With the engine off and the key in the on position does it still peg?
If you disconnect the sensor wire and do this again does it peg or stay
at -0-.
My 00 Sport sometimes pegs and will remain there for the drive cycle.I
changed the sensor,it was not the cause on mine.
When mine pegs I turn the key to the acc. position then off 2 or 3 times and
then it works again for a while,some kind if short.
Please post how you corrected yours. Thanks
"DougW" <post.replies@invalid.address> wrote in message
news:t3Yif.44107$2k5.6724@dukeread09...
> fladolphin did pass the time by typing:
>> The oil pressure gauge recently went to 80 one morning and has
>> consistently
>> stayed there. I had my oil changed to see if this would help but hasn't.
>> The vehicle is running fine, but the pressure is at 80??? This has never
>> happened, has always been around 40-50, then shot up to 80 and stayed.
>> From
>> what I have heard that the sender unit failed???? If this sounds right,
>> where is this unit located and is it easy to replace instead of going to
>> a
>> dealer?
>
> But first put the sensor wire back on, it fell off. :)
>
> http://members.***.net/wilsond/Fixes...l-pressure.jpg
> on the I6 it's down on the block just above the oil filter.
>
> Could be the sensor, it's easy to replace with simple hand tools
> and NAPA has the part.
>
> --
> DougW
>
#9
Guest
Posts: n/a
Re: Oil Sender Unit location 2000 Jeep Cherokee Sport
It is easy to change,and I got one aftermarket.
With the engine off and the key in the on position does it still peg?
If you disconnect the sensor wire and do this again does it peg or stay
at -0-.
My 00 Sport sometimes pegs and will remain there for the drive cycle.I
changed the sensor,it was not the cause on mine.
When mine pegs I turn the key to the acc. position then off 2 or 3 times and
then it works again for a while,some kind if short.
Please post how you corrected yours. Thanks
"DougW" <post.replies@invalid.address> wrote in message
news:t3Yif.44107$2k5.6724@dukeread09...
> fladolphin did pass the time by typing:
>> The oil pressure gauge recently went to 80 one morning and has
>> consistently
>> stayed there. I had my oil changed to see if this would help but hasn't.
>> The vehicle is running fine, but the pressure is at 80??? This has never
>> happened, has always been around 40-50, then shot up to 80 and stayed.
>> From
>> what I have heard that the sender unit failed???? If this sounds right,
>> where is this unit located and is it easy to replace instead of going to
>> a
>> dealer?
>
> But first put the sensor wire back on, it fell off. :)
>
> http://members.***.net/wilsond/Fixes...l-pressure.jpg
> on the I6 it's down on the block just above the oil filter.
>
> Could be the sensor, it's easy to replace with simple hand tools
> and NAPA has the part.
>
> --
> DougW
>
With the engine off and the key in the on position does it still peg?
If you disconnect the sensor wire and do this again does it peg or stay
at -0-.
My 00 Sport sometimes pegs and will remain there for the drive cycle.I
changed the sensor,it was not the cause on mine.
When mine pegs I turn the key to the acc. position then off 2 or 3 times and
then it works again for a while,some kind if short.
Please post how you corrected yours. Thanks
"DougW" <post.replies@invalid.address> wrote in message
news:t3Yif.44107$2k5.6724@dukeread09...
> fladolphin did pass the time by typing:
>> The oil pressure gauge recently went to 80 one morning and has
>> consistently
>> stayed there. I had my oil changed to see if this would help but hasn't.
>> The vehicle is running fine, but the pressure is at 80??? This has never
>> happened, has always been around 40-50, then shot up to 80 and stayed.
>> From
>> what I have heard that the sender unit failed???? If this sounds right,
>> where is this unit located and is it easy to replace instead of going to
>> a
>> dealer?
>
> But first put the sensor wire back on, it fell off. :)
>
> http://members.***.net/wilsond/Fixes...l-pressure.jpg
> on the I6 it's down on the block just above the oil filter.
>
> Could be the sensor, it's easy to replace with simple hand tools
> and NAPA has the part.
>
> --
> DougW
>
#10
Guest
Posts: n/a
Re: Oil Sender Unit location 2000 Jeep Cherokee Sport
It is easy to change,and I got one aftermarket.
With the engine off and the key in the on position does it still peg?
If you disconnect the sensor wire and do this again does it peg or stay
at -0-.
My 00 Sport sometimes pegs and will remain there for the drive cycle.I
changed the sensor,it was not the cause on mine.
When mine pegs I turn the key to the acc. position then off 2 or 3 times and
then it works again for a while,some kind if short.
Please post how you corrected yours. Thanks
"DougW" <post.replies@invalid.address> wrote in message
news:t3Yif.44107$2k5.6724@dukeread09...
> fladolphin did pass the time by typing:
>> The oil pressure gauge recently went to 80 one morning and has
>> consistently
>> stayed there. I had my oil changed to see if this would help but hasn't.
>> The vehicle is running fine, but the pressure is at 80??? This has never
>> happened, has always been around 40-50, then shot up to 80 and stayed.
>> From
>> what I have heard that the sender unit failed???? If this sounds right,
>> where is this unit located and is it easy to replace instead of going to
>> a
>> dealer?
>
> But first put the sensor wire back on, it fell off. :)
>
> http://members.***.net/wilsond/Fixes...l-pressure.jpg
> on the I6 it's down on the block just above the oil filter.
>
> Could be the sensor, it's easy to replace with simple hand tools
> and NAPA has the part.
>
> --
> DougW
>
With the engine off and the key in the on position does it still peg?
If you disconnect the sensor wire and do this again does it peg or stay
at -0-.
My 00 Sport sometimes pegs and will remain there for the drive cycle.I
changed the sensor,it was not the cause on mine.
When mine pegs I turn the key to the acc. position then off 2 or 3 times and
then it works again for a while,some kind if short.
Please post how you corrected yours. Thanks
"DougW" <post.replies@invalid.address> wrote in message
news:t3Yif.44107$2k5.6724@dukeread09...
> fladolphin did pass the time by typing:
>> The oil pressure gauge recently went to 80 one morning and has
>> consistently
>> stayed there. I had my oil changed to see if this would help but hasn't.
>> The vehicle is running fine, but the pressure is at 80??? This has never
>> happened, has always been around 40-50, then shot up to 80 and stayed.
>> From
>> what I have heard that the sender unit failed???? If this sounds right,
>> where is this unit located and is it easy to replace instead of going to
>> a
>> dealer?
>
> But first put the sensor wire back on, it fell off. :)
>
> http://members.***.net/wilsond/Fixes...l-pressure.jpg
> on the I6 it's down on the block just above the oil filter.
>
> Could be the sensor, it's easy to replace with simple hand tools
> and NAPA has the part.
>
> --
> DougW
>
Thread
Thread Starter
Forum
Replies
Last Post
klalani@thenuancegroup.com
Jeep Mailing List
6
12-09-2006 09:05 AM
josh00@comcast.net
Jeep Mailing List
6
11-28-2005 10:42 AM
josh00@comcast.net
Jeep Mailing List
24
04-24-2005 04:49 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)