Location of temperature gauge sending unit and troubleshooting T gauge.
#1
Guest
Posts: n/a
Location of temperature gauge sending unit and troubleshooting T gauge.
My temp gauge stopped working on my 92 YJ 4.0. Neddle is not moving at
all so I'm assuming a broken wire or a bad / disconnected sueding unit.
I looked around the block and I don't see anything it may be. Where is
the sending unit located and is there a ohm / resistance measurement I
can do to diagnose?
thanks
all so I'm assuming a broken wire or a bad / disconnected sueding unit.
I looked around the block and I don't see anything it may be. Where is
the sending unit located and is there a ohm / resistance measurement I
can do to diagnose?
thanks
#2
Guest
Posts: n/a
Re: Location of temperature gauge sending unit and troubleshooting T gauge.
josh00@comcast.net did pass the time by typing:
> My temp gauge stopped working on my 92 YJ 4.0. Neddle is not moving at
> all so I'm assuming a broken wire or a bad / disconnected sueding unit.
> I looked around the block and I don't see anything it may be. Where is
> the sending unit located and is there a ohm / resistance measurement I
> can do to diagnose?
Probably the same as my 93ZJ.
http://members.***.net/wilsond/Fixes...ml#sensor-temp
--
-- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
> My temp gauge stopped working on my 92 YJ 4.0. Neddle is not moving at
> all so I'm assuming a broken wire or a bad / disconnected sueding unit.
> I looked around the block and I don't see anything it may be. Where is
> the sending unit located and is there a ohm / resistance measurement I
> can do to diagnose?
Probably the same as my 93ZJ.
http://members.***.net/wilsond/Fixes...ml#sensor-temp
--
-- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
#3
Guest
Posts: n/a
Re: Location of temperature gauge sending unit and troubleshooting T gauge.
josh00@comcast.net did pass the time by typing:
> My temp gauge stopped working on my 92 YJ 4.0. Neddle is not moving at
> all so I'm assuming a broken wire or a bad / disconnected sueding unit.
> I looked around the block and I don't see anything it may be. Where is
> the sending unit located and is there a ohm / resistance measurement I
> can do to diagnose?
Probably the same as my 93ZJ.
http://members.***.net/wilsond/Fixes...ml#sensor-temp
--
-- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
> My temp gauge stopped working on my 92 YJ 4.0. Neddle is not moving at
> all so I'm assuming a broken wire or a bad / disconnected sueding unit.
> I looked around the block and I don't see anything it may be. Where is
> the sending unit located and is there a ohm / resistance measurement I
> can do to diagnose?
Probably the same as my 93ZJ.
http://members.***.net/wilsond/Fixes...ml#sensor-temp
--
-- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
#4
Guest
Posts: n/a
Re: Location of temperature gauge sending unit and troubleshooting T gauge.
josh00@comcast.net did pass the time by typing:
> My temp gauge stopped working on my 92 YJ 4.0. Neddle is not moving at
> all so I'm assuming a broken wire or a bad / disconnected sueding unit.
> I looked around the block and I don't see anything it may be. Where is
> the sending unit located and is there a ohm / resistance measurement I
> can do to diagnose?
Probably the same as my 93ZJ.
http://members.***.net/wilsond/Fixes...ml#sensor-temp
--
-- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
> My temp gauge stopped working on my 92 YJ 4.0. Neddle is not moving at
> all so I'm assuming a broken wire or a bad / disconnected sueding unit.
> I looked around the block and I don't see anything it may be. Where is
> the sending unit located and is there a ohm / resistance measurement I
> can do to diagnose?
Probably the same as my 93ZJ.
http://members.***.net/wilsond/Fixes...ml#sensor-temp
--
-- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
#5
Guest
Posts: n/a
Re: Location of temperature gauge sending unit and troubleshooting T gauge.
josh00@comcast.net did pass the time by typing:
> My temp gauge stopped working on my 92 YJ 4.0. Neddle is not moving at
> all so I'm assuming a broken wire or a bad / disconnected sueding unit.
> I looked around the block and I don't see anything it may be. Where is
> the sending unit located and is there a ohm / resistance measurement I
> can do to diagnose?
Probably the same as my 93ZJ.
http://members.***.net/wilsond/Fixes...ml#sensor-temp
--
-- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
> My temp gauge stopped working on my 92 YJ 4.0. Neddle is not moving at
> all so I'm assuming a broken wire or a bad / disconnected sueding unit.
> I looked around the block and I don't see anything it may be. Where is
> the sending unit located and is there a ohm / resistance measurement I
> can do to diagnose?
Probably the same as my 93ZJ.
http://members.***.net/wilsond/Fixes...ml#sensor-temp
--
-- DougW -- 93 ZJ 4.0 http://members.***.net/wilsond
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
#6
Guest
Posts: n/a
Re: Location of temperature gauge sending unit and troubleshooting T gauge.
my 89 wrangler sending unit is on the intake manifold, in the back by the
fire wall. There is a Purple wire on mine leading to the sending unit. I'm
Not sure about the ohm resistence on the yj.
The following is for a cj-
With an ohmmeter check the resistance between the post and ground.
73 ohms - Cold Test when engine is slightly warm. A stone cold engine will
read a much higher resistance.
36 ohms - Beginning of Band
13 ohms - End of Band
9 ohms - Hot
--
Message posted via http://www.carkb.com
fire wall. There is a Purple wire on mine leading to the sending unit. I'm
Not sure about the ohm resistence on the yj.
The following is for a cj-
With an ohmmeter check the resistance between the post and ground.
73 ohms - Cold Test when engine is slightly warm. A stone cold engine will
read a much higher resistance.
36 ohms - Beginning of Band
13 ohms - End of Band
9 ohms - Hot
--
Message posted via http://www.carkb.com
#7
Guest
Posts: n/a
Re: Location of temperature gauge sending unit and troubleshooting T gauge.
my 89 wrangler sending unit is on the intake manifold, in the back by the
fire wall. There is a Purple wire on mine leading to the sending unit. I'm
Not sure about the ohm resistence on the yj.
The following is for a cj-
With an ohmmeter check the resistance between the post and ground.
73 ohms - Cold Test when engine is slightly warm. A stone cold engine will
read a much higher resistance.
36 ohms - Beginning of Band
13 ohms - End of Band
9 ohms - Hot
--
Message posted via http://www.carkb.com
fire wall. There is a Purple wire on mine leading to the sending unit. I'm
Not sure about the ohm resistence on the yj.
The following is for a cj-
With an ohmmeter check the resistance between the post and ground.
73 ohms - Cold Test when engine is slightly warm. A stone cold engine will
read a much higher resistance.
36 ohms - Beginning of Band
13 ohms - End of Band
9 ohms - Hot
--
Message posted via http://www.carkb.com
#8
Guest
Posts: n/a
Re: Location of temperature gauge sending unit and troubleshooting T gauge.
my 89 wrangler sending unit is on the intake manifold, in the back by the
fire wall. There is a Purple wire on mine leading to the sending unit. I'm
Not sure about the ohm resistence on the yj.
The following is for a cj-
With an ohmmeter check the resistance between the post and ground.
73 ohms - Cold Test when engine is slightly warm. A stone cold engine will
read a much higher resistance.
36 ohms - Beginning of Band
13 ohms - End of Band
9 ohms - Hot
--
Message posted via http://www.carkb.com
fire wall. There is a Purple wire on mine leading to the sending unit. I'm
Not sure about the ohm resistence on the yj.
The following is for a cj-
With an ohmmeter check the resistance between the post and ground.
73 ohms - Cold Test when engine is slightly warm. A stone cold engine will
read a much higher resistance.
36 ohms - Beginning of Band
13 ohms - End of Band
9 ohms - Hot
--
Message posted via http://www.carkb.com
#9
Guest
Posts: n/a
Re: Location of temperature gauge sending unit and troubleshooting T gauge.
my 89 wrangler sending unit is on the intake manifold, in the back by the
fire wall. There is a Purple wire on mine leading to the sending unit. I'm
Not sure about the ohm resistence on the yj.
The following is for a cj-
With an ohmmeter check the resistance between the post and ground.
73 ohms - Cold Test when engine is slightly warm. A stone cold engine will
read a much higher resistance.
36 ohms - Beginning of Band
13 ohms - End of Band
9 ohms - Hot
--
Message posted via http://www.carkb.com
fire wall. There is a Purple wire on mine leading to the sending unit. I'm
Not sure about the ohm resistence on the yj.
The following is for a cj-
With an ohmmeter check the resistance between the post and ground.
73 ohms - Cold Test when engine is slightly warm. A stone cold engine will
read a much higher resistance.
36 ohms - Beginning of Band
13 ohms - End of Band
9 ohms - Hot
--
Message posted via http://www.carkb.com
#10
Guest
Posts: n/a
Re: Location of temperature gauge sending unit and troubleshooting T gauge.
Mike or someone had posted that CJ one for me. I'd be interested if
someone had a list of all the guages and what they should read for the
YJ's.
Robb 89 YJ
--
Message posted via http://www.carkb.com
someone had a list of all the guages and what they should read for the
YJ's.
Robb 89 YJ
--
Message posted via http://www.carkb.com