O.T. tach for chainsaw?
#11
Guest
Posts: n/a
Re: O.T. tach for chainsaw?
FrankW <fworm@mxznorpak.ca> wrote:
> After rebuilding the carb for my little Homelite chainsaw.
> I needed to readjust the hi and lo jets.
> The lo jet was easy enough but to adjust the hi speed jet
> the manual says to adjust to 11,000 - 11,500 rpm.
> What kind of tool do you use to measure the rpm?
You'd need something like this:
http://www.mfgsupply.com/m/c/32-9073.html
But since you probably don't have one of those or can justify the price, you
can probably do the following:
At WOT, keep turning the high speed jet richer until the saw "four-cycles".
This is a distinctive sound that a 2-cycle engine makes when it is running too
rich. You'll know it when you hear it.
Then, turn the high speed jet leaner until the "four-cycle" sound just goes
away.
Or just stop by a local small engine shop. They probably have a tach like
the one mentioned above and would probably be willing to adjust the carb for
you for nothing, or perhaps a beer...
:)
-John
> After rebuilding the carb for my little Homelite chainsaw.
> I needed to readjust the hi and lo jets.
> The lo jet was easy enough but to adjust the hi speed jet
> the manual says to adjust to 11,000 - 11,500 rpm.
> What kind of tool do you use to measure the rpm?
You'd need something like this:
http://www.mfgsupply.com/m/c/32-9073.html
But since you probably don't have one of those or can justify the price, you
can probably do the following:
At WOT, keep turning the high speed jet richer until the saw "four-cycles".
This is a distinctive sound that a 2-cycle engine makes when it is running too
rich. You'll know it when you hear it.
Then, turn the high speed jet leaner until the "four-cycle" sound just goes
away.
Or just stop by a local small engine shop. They probably have a tach like
the one mentioned above and would probably be willing to adjust the carb for
you for nothing, or perhaps a beer...
:)
-John
#12
Guest
Posts: n/a
Re: O.T. tach for chainsaw?
FrankW <fworm@mxznorpak.ca> wrote:
> After rebuilding the carb for my little Homelite chainsaw.
> I needed to readjust the hi and lo jets.
> The lo jet was easy enough but to adjust the hi speed jet
> the manual says to adjust to 11,000 - 11,500 rpm.
> What kind of tool do you use to measure the rpm?
You'd need something like this:
http://www.mfgsupply.com/m/c/32-9073.html
But since you probably don't have one of those or can justify the price, you
can probably do the following:
At WOT, keep turning the high speed jet richer until the saw "four-cycles".
This is a distinctive sound that a 2-cycle engine makes when it is running too
rich. You'll know it when you hear it.
Then, turn the high speed jet leaner until the "four-cycle" sound just goes
away.
Or just stop by a local small engine shop. They probably have a tach like
the one mentioned above and would probably be willing to adjust the carb for
you for nothing, or perhaps a beer...
:)
-John
> After rebuilding the carb for my little Homelite chainsaw.
> I needed to readjust the hi and lo jets.
> The lo jet was easy enough but to adjust the hi speed jet
> the manual says to adjust to 11,000 - 11,500 rpm.
> What kind of tool do you use to measure the rpm?
You'd need something like this:
http://www.mfgsupply.com/m/c/32-9073.html
But since you probably don't have one of those or can justify the price, you
can probably do the following:
At WOT, keep turning the high speed jet richer until the saw "four-cycles".
This is a distinctive sound that a 2-cycle engine makes when it is running too
rich. You'll know it when you hear it.
Then, turn the high speed jet leaner until the "four-cycle" sound just goes
away.
Or just stop by a local small engine shop. They probably have a tach like
the one mentioned above and would probably be willing to adjust the carb for
you for nothing, or perhaps a beer...
:)
-John
#13
Guest
Posts: n/a
Re: O.T. tach for chainsaw?
FrankW <fworm@mxznorpak.ca> wrote:
> After rebuilding the carb for my little Homelite chainsaw.
> I needed to readjust the hi and lo jets.
> The lo jet was easy enough but to adjust the hi speed jet
> the manual says to adjust to 11,000 - 11,500 rpm.
> What kind of tool do you use to measure the rpm?
You'd need something like this:
http://www.mfgsupply.com/m/c/32-9073.html
But since you probably don't have one of those or can justify the price, you
can probably do the following:
At WOT, keep turning the high speed jet richer until the saw "four-cycles".
This is a distinctive sound that a 2-cycle engine makes when it is running too
rich. You'll know it when you hear it.
Then, turn the high speed jet leaner until the "four-cycle" sound just goes
away.
Or just stop by a local small engine shop. They probably have a tach like
the one mentioned above and would probably be willing to adjust the carb for
you for nothing, or perhaps a beer...
:)
-John
> After rebuilding the carb for my little Homelite chainsaw.
> I needed to readjust the hi and lo jets.
> The lo jet was easy enough but to adjust the hi speed jet
> the manual says to adjust to 11,000 - 11,500 rpm.
> What kind of tool do you use to measure the rpm?
You'd need something like this:
http://www.mfgsupply.com/m/c/32-9073.html
But since you probably don't have one of those or can justify the price, you
can probably do the following:
At WOT, keep turning the high speed jet richer until the saw "four-cycles".
This is a distinctive sound that a 2-cycle engine makes when it is running too
rich. You'll know it when you hear it.
Then, turn the high speed jet leaner until the "four-cycle" sound just goes
away.
Or just stop by a local small engine shop. They probably have a tach like
the one mentioned above and would probably be willing to adjust the carb for
you for nothing, or perhaps a beer...
:)
-John
#17
Guest
Posts: n/a
Re: O.T. tach for chainsaw?
Hi Mike
No the bbok says to adjust to the desired rpm only.
It doesn't say anything else about it.
Mike Romain wrote:
> If you run it lean, it will just stop until it cools down.
>
> I prefer to start rich and bring them lean. I find it pretty easy to
> hear the difference when it leans out smooth. Too lean and it will
> miss. Does the book say to lean it until it misses and then make it
> rich so many turns?
>
> Mike
>
> FrankW wrote:
>
>>Hi Mike
>>According to the manual I have to run it WOT
>>and adjust it to 11,000-11,500 rpm. Since it's a 2 stroke
>>I don't want to run it to lean.
>>
>>Mike Romain wrote:
>>
>>>I use the trigger..... ;-)
>>>
>>>Seriously, that is WOT where it normally runs. It is normally either at
>>>idle or wide open when running. Any half throttle cuts are usually
>>>rare....
>>>
>>>Mike
>>>86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
>>>88 Cherokee 235 BFG AT's
>>>
>>>FrankW wrote:
>>>
>>>
>>>>Hello Group.
>>>>After rebuilding the carb for my little Homelite chainsaw.
>>>>I needed to readjust the hi and lo jets.
>>>>The lo jet was easy enough but to adjust the hi speed jet
>>>>the manual says to adjust to 11,000 - 11,500 rpm.
>>>>What kind of tool do you use to measure the rpm?
>>>>Thanks in advance.
>>>>Frank .....lousy mechanic.....worse plumber
No the bbok says to adjust to the desired rpm only.
It doesn't say anything else about it.
Mike Romain wrote:
> If you run it lean, it will just stop until it cools down.
>
> I prefer to start rich and bring them lean. I find it pretty easy to
> hear the difference when it leans out smooth. Too lean and it will
> miss. Does the book say to lean it until it misses and then make it
> rich so many turns?
>
> Mike
>
> FrankW wrote:
>
>>Hi Mike
>>According to the manual I have to run it WOT
>>and adjust it to 11,000-11,500 rpm. Since it's a 2 stroke
>>I don't want to run it to lean.
>>
>>Mike Romain wrote:
>>
>>>I use the trigger..... ;-)
>>>
>>>Seriously, that is WOT where it normally runs. It is normally either at
>>>idle or wide open when running. Any half throttle cuts are usually
>>>rare....
>>>
>>>Mike
>>>86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
>>>88 Cherokee 235 BFG AT's
>>>
>>>FrankW wrote:
>>>
>>>
>>>>Hello Group.
>>>>After rebuilding the carb for my little Homelite chainsaw.
>>>>I needed to readjust the hi and lo jets.
>>>>The lo jet was easy enough but to adjust the hi speed jet
>>>>the manual says to adjust to 11,000 - 11,500 rpm.
>>>>What kind of tool do you use to measure the rpm?
>>>>Thanks in advance.
>>>>Frank .....lousy mechanic.....worse plumber
#18
Guest
Posts: n/a
Re: O.T. tach for chainsaw?
Hi Mike
No the bbok says to adjust to the desired rpm only.
It doesn't say anything else about it.
Mike Romain wrote:
> If you run it lean, it will just stop until it cools down.
>
> I prefer to start rich and bring them lean. I find it pretty easy to
> hear the difference when it leans out smooth. Too lean and it will
> miss. Does the book say to lean it until it misses and then make it
> rich so many turns?
>
> Mike
>
> FrankW wrote:
>
>>Hi Mike
>>According to the manual I have to run it WOT
>>and adjust it to 11,000-11,500 rpm. Since it's a 2 stroke
>>I don't want to run it to lean.
>>
>>Mike Romain wrote:
>>
>>>I use the trigger..... ;-)
>>>
>>>Seriously, that is WOT where it normally runs. It is normally either at
>>>idle or wide open when running. Any half throttle cuts are usually
>>>rare....
>>>
>>>Mike
>>>86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
>>>88 Cherokee 235 BFG AT's
>>>
>>>FrankW wrote:
>>>
>>>
>>>>Hello Group.
>>>>After rebuilding the carb for my little Homelite chainsaw.
>>>>I needed to readjust the hi and lo jets.
>>>>The lo jet was easy enough but to adjust the hi speed jet
>>>>the manual says to adjust to 11,000 - 11,500 rpm.
>>>>What kind of tool do you use to measure the rpm?
>>>>Thanks in advance.
>>>>Frank .....lousy mechanic.....worse plumber
No the bbok says to adjust to the desired rpm only.
It doesn't say anything else about it.
Mike Romain wrote:
> If you run it lean, it will just stop until it cools down.
>
> I prefer to start rich and bring them lean. I find it pretty easy to
> hear the difference when it leans out smooth. Too lean and it will
> miss. Does the book say to lean it until it misses and then make it
> rich so many turns?
>
> Mike
>
> FrankW wrote:
>
>>Hi Mike
>>According to the manual I have to run it WOT
>>and adjust it to 11,000-11,500 rpm. Since it's a 2 stroke
>>I don't want to run it to lean.
>>
>>Mike Romain wrote:
>>
>>>I use the trigger..... ;-)
>>>
>>>Seriously, that is WOT where it normally runs. It is normally either at
>>>idle or wide open when running. Any half throttle cuts are usually
>>>rare....
>>>
>>>Mike
>>>86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
>>>88 Cherokee 235 BFG AT's
>>>
>>>FrankW wrote:
>>>
>>>
>>>>Hello Group.
>>>>After rebuilding the carb for my little Homelite chainsaw.
>>>>I needed to readjust the hi and lo jets.
>>>>The lo jet was easy enough but to adjust the hi speed jet
>>>>the manual says to adjust to 11,000 - 11,500 rpm.
>>>>What kind of tool do you use to measure the rpm?
>>>>Thanks in advance.
>>>>Frank .....lousy mechanic.....worse plumber
#19
Guest
Posts: n/a
Re: O.T. tach for chainsaw?
Hi Mike
No the bbok says to adjust to the desired rpm only.
It doesn't say anything else about it.
Mike Romain wrote:
> If you run it lean, it will just stop until it cools down.
>
> I prefer to start rich and bring them lean. I find it pretty easy to
> hear the difference when it leans out smooth. Too lean and it will
> miss. Does the book say to lean it until it misses and then make it
> rich so many turns?
>
> Mike
>
> FrankW wrote:
>
>>Hi Mike
>>According to the manual I have to run it WOT
>>and adjust it to 11,000-11,500 rpm. Since it's a 2 stroke
>>I don't want to run it to lean.
>>
>>Mike Romain wrote:
>>
>>>I use the trigger..... ;-)
>>>
>>>Seriously, that is WOT where it normally runs. It is normally either at
>>>idle or wide open when running. Any half throttle cuts are usually
>>>rare....
>>>
>>>Mike
>>>86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
>>>88 Cherokee 235 BFG AT's
>>>
>>>FrankW wrote:
>>>
>>>
>>>>Hello Group.
>>>>After rebuilding the carb for my little Homelite chainsaw.
>>>>I needed to readjust the hi and lo jets.
>>>>The lo jet was easy enough but to adjust the hi speed jet
>>>>the manual says to adjust to 11,000 - 11,500 rpm.
>>>>What kind of tool do you use to measure the rpm?
>>>>Thanks in advance.
>>>>Frank .....lousy mechanic.....worse plumber
No the bbok says to adjust to the desired rpm only.
It doesn't say anything else about it.
Mike Romain wrote:
> If you run it lean, it will just stop until it cools down.
>
> I prefer to start rich and bring them lean. I find it pretty easy to
> hear the difference when it leans out smooth. Too lean and it will
> miss. Does the book say to lean it until it misses and then make it
> rich so many turns?
>
> Mike
>
> FrankW wrote:
>
>>Hi Mike
>>According to the manual I have to run it WOT
>>and adjust it to 11,000-11,500 rpm. Since it's a 2 stroke
>>I don't want to run it to lean.
>>
>>Mike Romain wrote:
>>
>>>I use the trigger..... ;-)
>>>
>>>Seriously, that is WOT where it normally runs. It is normally either at
>>>idle or wide open when running. Any half throttle cuts are usually
>>>rare....
>>>
>>>Mike
>>>86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
>>>88 Cherokee 235 BFG AT's
>>>
>>>FrankW wrote:
>>>
>>>
>>>>Hello Group.
>>>>After rebuilding the carb for my little Homelite chainsaw.
>>>>I needed to readjust the hi and lo jets.
>>>>The lo jet was easy enough but to adjust the hi speed jet
>>>>the manual says to adjust to 11,000 - 11,500 rpm.
>>>>What kind of tool do you use to measure the rpm?
>>>>Thanks in advance.
>>>>Frank .....lousy mechanic.....worse plumber
#20
Guest
Posts: n/a
Re: O.T. tach for chainsaw?
Hmmm a 4 stroke sound. Is that like when it's
sorta flooding out? Like putting the choke on
I plan on buying a new bar and chain for it
Maybe they'll put a tach on it for me if I do buy
the bar+chain. The local small engine shop I use
are pretty darn good. For parts anyway...
John Sevey wrote:
> FrankW <fworm@mxznorpak.ca> wrote:
>
>>After rebuilding the carb for my little Homelite chainsaw.
>>I needed to readjust the hi and lo jets.
>>The lo jet was easy enough but to adjust the hi speed jet
>>the manual says to adjust to 11,000 - 11,500 rpm.
>>What kind of tool do you use to measure the rpm?
>
>
> You'd need something like this:
>
> http://www.mfgsupply.com/m/c/32-9073.html
>
> But since you probably don't have one of those or can justify the price, you
> can probably do the following:
>
> At WOT, keep turning the high speed jet richer until the saw "four-cycles".
>
> This is a distinctive sound that a 2-cycle engine makes when it is running too
> rich. You'll know it when you hear it.
>
> Then, turn the high speed jet leaner until the "four-cycle" sound just goes
> away.
>
> Or just stop by a local small engine shop. They probably have a tach like
> the one mentioned above and would probably be willing to adjust the carb for
> you for nothing, or perhaps a beer...
>
> :)
>
> -John
sorta flooding out? Like putting the choke on
I plan on buying a new bar and chain for it
Maybe they'll put a tach on it for me if I do buy
the bar+chain. The local small engine shop I use
are pretty darn good. For parts anyway...
John Sevey wrote:
> FrankW <fworm@mxznorpak.ca> wrote:
>
>>After rebuilding the carb for my little Homelite chainsaw.
>>I needed to readjust the hi and lo jets.
>>The lo jet was easy enough but to adjust the hi speed jet
>>the manual says to adjust to 11,000 - 11,500 rpm.
>>What kind of tool do you use to measure the rpm?
>
>
> You'd need something like this:
>
> http://www.mfgsupply.com/m/c/32-9073.html
>
> But since you probably don't have one of those or can justify the price, you
> can probably do the following:
>
> At WOT, keep turning the high speed jet richer until the saw "four-cycles".
>
> This is a distinctive sound that a 2-cycle engine makes when it is running too
> rich. You'll know it when you hear it.
>
> Then, turn the high speed jet leaner until the "four-cycle" sound just goes
> away.
>
> Or just stop by a local small engine shop. They probably have a tach like
> the one mentioned above and would probably be willing to adjust the carb for
> you for nothing, or perhaps a beer...
>
> :)
>
> -John