MIL Trouble Code 12 Meaning
 

Having long known that trouble code 12 (as flashed by the
Malfunction Indicator Light, or MIL, AKA the "CHECK ENGINE" light
after one does the start with key off, switch key on, key off,
key on, key off, key on, leave key on and count groups of flashes
until done, then turn key off) does not mean what my '96 Jeep Cherokee
service manual says it means, I've been curious about it. I've just
completed some homework and reached my own conclusion about what code
12 really means.

The widely-reported meaning is "battery recently disconnected"
(supposedly within the last 50 key-on cycles), but I've known for a
long time that this isn't quite right.

I have now concluded that code 12 means "emissions systems not
yet proven good". It seems to be reported when:
a.) an emissions-related "monitor" has not yet run its testing,
b.) an emissions-related trouble code is stored, or
c.) ??? maybe some other circumstance I haven't learned yet,
perhaps some numbers of consecutive passing runs of
various emissions-related "monitors" after codes
are cleared.

This neatly explains why:
1.) a battery disconnect causes code 12 (all "monitors" would then
be flagged as not yet having run their tests),
2.) code 12 can appear without a battery disconnect or loss of
connection having occurred (code 12 shows up when certain
other trouble codes get recorded), and
3.) it can take MANY more than 50 key-on cycles for code 12 to
go away, even if no other trouble code is reported
(probably depends on how one's driving patterns compare to
the trigger conditions for running of the various "monitors").

The word "monitor" seems to be jargon for any of various sets
of firmware routines responsible for monitoring and|or testing various
sets of subsystems within the vehicle.

I hope this helps lessen the confusion over code 12.

Happy JEEPing!


-----
Greg Thoman: The opinions expressed herein are mine alone, and I am
solely irresponsible for them.

Re: MIL Trouble Code 12 Meaning
 

Your assumptions are interesting. The 12 code shows up when battery
has been disconnected , for sure. It also shows up if/when your
battery drops below a certain voltage at anytime, especially when
cranking. This can happen at any time, even to a perfectly good
battery. That is why you see a code 12 alot of times.
Thanks for your time.


thoman@frii.com wrote in message news:<3fa4a574$0$202$75868355@news.frii.net>...
> Having long known that trouble code 12 (as flashed by the
> Malfunction Indicator Light, or MIL, AKA the "CHECK ENGINE" light
> after one does the start with key off, switch key on, key off,
> key on, key off, key on, leave key on and count groups of flashes
> until done, then turn key off) does not mean what my '96 Jeep Cherokee
> service manual says it means, I've been curious about it. I've just
> completed some homework and reached my own conclusion about what code
> 12 really means.
>
> The widely-reported meaning is "battery recently disconnected"
> (supposedly within the last 50 key-on cycles), but I've known for a
> long time that this isn't quite right.
>
> I have now concluded that code 12 means "emissions systems not
> yet proven good". It seems to be reported when:
> a.) an emissions-related "monitor" has not yet run its testing,
> b.) an emissions-related trouble code is stored, or
> c.) ??? maybe some other circumstance I haven't learned yet,
> perhaps some numbers of consecutive passing runs of
> various emissions-related "monitors" after codes
> are cleared.
>
> This neatly explains why:
> 1.) a battery disconnect causes code 12 (all "monitors" would then
> be flagged as not yet having run their tests),
> 2.) code 12 can appear without a battery disconnect or loss of
> connection having occurred (code 12 shows up when certain
> other trouble codes get recorded), and
> 3.) it can take MANY more than 50 key-on cycles for code 12 to
> go away, even if no other trouble code is reported
> (probably depends on how one's driving patterns compare to
> the trigger conditions for running of the various "monitors").
>
> The word "monitor" seems to be jargon for any of various sets
> of firmware routines responsible for monitoring and|or testing various
> sets of subsystems within the vehicle.
>
> I hope this helps lessen the confusion over code 12.
>
> Happy JEEPing!
>
>
> -----
> Greg Thoman: The opinions expressed herein are mine alone, and I am
> solely irresponsible for them.

Re: MIL Trouble Code 12 Meaning
 

Your assumptions are interesting. The 12 code shows up when battery
has been disconnected , for sure. It also shows up if/when your
battery drops below a certain voltage at anytime, especially when
cranking. This can happen at any time, even to a perfectly good
battery. That is why you see a code 12 alot of times.
Thanks for your time.


thoman@frii.com wrote in message news:<3fa4a574$0$202$75868355@news.frii.net>...
> Having long known that trouble code 12 (as flashed by the
> Malfunction Indicator Light, or MIL, AKA the "CHECK ENGINE" light
> after one does the start with key off, switch key on, key off,
> key on, key off, key on, leave key on and count groups of flashes
> until done, then turn key off) does not mean what my '96 Jeep Cherokee
> service manual says it means, I've been curious about it. I've just
> completed some homework and reached my own conclusion about what code
> 12 really means.
>
> The widely-reported meaning is "battery recently disconnected"
> (supposedly within the last 50 key-on cycles), but I've known for a
> long time that this isn't quite right.
>
> I have now concluded that code 12 means "emissions systems not
> yet proven good". It seems to be reported when:
> a.) an emissions-related "monitor" has not yet run its testing,
> b.) an emissions-related trouble code is stored, or
> c.) ??? maybe some other circumstance I haven't learned yet,
> perhaps some numbers of consecutive passing runs of
> various emissions-related "monitors" after codes
> are cleared.
>
> This neatly explains why:
> 1.) a battery disconnect causes code 12 (all "monitors" would then
> be flagged as not yet having run their tests),
> 2.) code 12 can appear without a battery disconnect or loss of
> connection having occurred (code 12 shows up when certain
> other trouble codes get recorded), and
> 3.) it can take MANY more than 50 key-on cycles for code 12 to
> go away, even if no other trouble code is reported
> (probably depends on how one's driving patterns compare to
> the trigger conditions for running of the various "monitors").
>
> The word "monitor" seems to be jargon for any of various sets
> of firmware routines responsible for monitoring and|or testing various
> sets of subsystems within the vehicle.
>
> I hope this helps lessen the confusion over code 12.
>
> Happy JEEPing!
>
>
> -----
> Greg Thoman: The opinions expressed herein are mine alone, and I am
> solely irresponsible for them.

Re: MIL Trouble Code 12 Meaning
 

Your assumptions are interesting. The 12 code shows up when battery
has been disconnected , for sure. It also shows up if/when your
battery drops below a certain voltage at anytime, especially when
cranking. This can happen at any time, even to a perfectly good
battery. That is why you see a code 12 alot of times.
Thanks for your time.


thoman@frii.com wrote in message news:<3fa4a574$0$202$75868355@news.frii.net>...
> Having long known that trouble code 12 (as flashed by the
> Malfunction Indicator Light, or MIL, AKA the "CHECK ENGINE" light
> after one does the start with key off, switch key on, key off,
> key on, key off, key on, leave key on and count groups of flashes
> until done, then turn key off) does not mean what my '96 Jeep Cherokee
> service manual says it means, I've been curious about it. I've just
> completed some homework and reached my own conclusion about what code
> 12 really means.
>
> The widely-reported meaning is "battery recently disconnected"
> (supposedly within the last 50 key-on cycles), but I've known for a
> long time that this isn't quite right.
>
> I have now concluded that code 12 means "emissions systems not
> yet proven good". It seems to be reported when:
> a.) an emissions-related "monitor" has not yet run its testing,
> b.) an emissions-related trouble code is stored, or
> c.) ??? maybe some other circumstance I haven't learned yet,
> perhaps some numbers of consecutive passing runs of
> various emissions-related "monitors" after codes
> are cleared.
>
> This neatly explains why:
> 1.) a battery disconnect causes code 12 (all "monitors" would then
> be flagged as not yet having run their tests),
> 2.) code 12 can appear without a battery disconnect or loss of
> connection having occurred (code 12 shows up when certain
> other trouble codes get recorded), and
> 3.) it can take MANY more than 50 key-on cycles for code 12 to
> go away, even if no other trouble code is reported
> (probably depends on how one's driving patterns compare to
> the trigger conditions for running of the various "monitors").
>
> The word "monitor" seems to be jargon for any of various sets
> of firmware routines responsible for monitoring and|or testing various
> sets of subsystems within the vehicle.
>
> I hope this helps lessen the confusion over code 12.
>
> Happy JEEPing!
>
>
> -----
> Greg Thoman: The opinions expressed herein are mine alone, and I am
> solely irresponsible for them.

Re: MIL Trouble Code 12 Meaning
 

This code occurs any time the engine controller microprocessor has a
low voltage reset. This occurs when the voltage AT THE ENGINE
COMPUTER goes below 6 volts.
This can occur during the first millisecond of engine cranking if the
battery or any of the connections that carry the starter current get
rusty and build up a higher than normal resistance. A few extra
milliohms will do this. During a start cycle the lowest battery
voltage occurs when the starter contactor closes but the starter and
engine has not yet begun to spin. This does not last very long, less
than a millisecond. You need to use a digital storage oscilloscope to
see this.

Get your self a good DVM, and a one amp or more load resistor. Then
learn what a 4 wire KELVIN resistance connection means. Then find
the high resistance that is causing the problem. ( E=IR ) Once you
understand what you are doing you can find the problem in less than a
hour most of the time.
John.


On 02 Nov 2003 06:34:30 GMT, thoman@frii.com wrote:

> Having long known that trouble code 12 (as flashed by the
>Malfunction Indicator Light, or MIL, AKA the "CHECK ENGINE" light
>after one does the start with key off, switch key on, key off,
>key on, key off, key on, leave key on and count groups of flashes
>until done, then turn key off) does not mean what my '96 Jeep Cherokee
>service manual says it means, I've been curious about it. I've just
>completed some homework and reached my own conclusion about what code
>12 really means.
>
> The widely-reported meaning is "battery recently disconnected"
>(supposedly within the last 50 key-on cycles), but I've known for a
>long time that this isn't quite right.
>
> I have now concluded that code 12 means "emissions systems not
>yet proven good". It seems to be reported when:
> a.) an emissions-related "monitor" has not yet run its testing,
> b.) an emissions-related trouble code is stored, or
> c.) ??? maybe some other circumstance I haven't learned yet,
> perhaps some numbers of consecutive passing runs of
> various emissions-related "monitors" after codes
> are cleared.
>
> This neatly explains why:
> 1.) a battery disconnect causes code 12 (all "monitors" would then
> be flagged as not yet having run their tests),
> 2.) code 12 can appear without a battery disconnect or loss of
> connection having occurred (code 12 shows up when certain
> other trouble codes get recorded), and
> 3.) it can take MANY more than 50 key-on cycles for code 12 to
> go away, even if no other trouble code is reported
> (probably depends on how one's driving patterns compare to
> the trigger conditions for running of the various "monitors").
>
> The word "monitor" seems to be jargon for any of various sets
>of firmware routines responsible for monitoring and|or testing various
>sets of subsystems within the vehicle.
>
> I hope this helps lessen the confusion over code 12.
>
> Happy JEEPing!
>
>
>-----
>Greg Thoman: The opinions expressed herein are mine alone, and I am
> solely irresponsible for them.

Re: MIL Trouble Code 12 Meaning
 

This code occurs any time the engine controller microprocessor has a
low voltage reset. This occurs when the voltage AT THE ENGINE
COMPUTER goes below 6 volts.
This can occur during the first millisecond of engine cranking if the
battery or any of the connections that carry the starter current get
rusty and build up a higher than normal resistance. A few extra
milliohms will do this. During a start cycle the lowest battery
voltage occurs when the starter contactor closes but the starter and
engine has not yet begun to spin. This does not last very long, less
than a millisecond. You need to use a digital storage oscilloscope to
see this.

Get your self a good DVM, and a one amp or more load resistor. Then
learn what a 4 wire KELVIN resistance connection means. Then find
the high resistance that is causing the problem. ( E=IR ) Once you
understand what you are doing you can find the problem in less than a
hour most of the time.
John.


On 02 Nov 2003 06:34:30 GMT, thoman@frii.com wrote:

> Having long known that trouble code 12 (as flashed by the
>Malfunction Indicator Light, or MIL, AKA the "CHECK ENGINE" light
>after one does the start with key off, switch key on, key off,
>key on, key off, key on, leave key on and count groups of flashes
>until done, then turn key off) does not mean what my '96 Jeep Cherokee
>service manual says it means, I've been curious about it. I've just
>completed some homework and reached my own conclusion about what code
>12 really means.
>
> The widely-reported meaning is "battery recently disconnected"
>(supposedly within the last 50 key-on cycles), but I've known for a
>long time that this isn't quite right.
>
> I have now concluded that code 12 means "emissions systems not
>yet proven good". It seems to be reported when:
> a.) an emissions-related "monitor" has not yet run its testing,
> b.) an emissions-related trouble code is stored, or
> c.) ??? maybe some other circumstance I haven't learned yet,
> perhaps some numbers of consecutive passing runs of
> various emissions-related "monitors" after codes
> are cleared.
>
> This neatly explains why:
> 1.) a battery disconnect causes code 12 (all "monitors" would then
> be flagged as not yet having run their tests),
> 2.) code 12 can appear without a battery disconnect or loss of
> connection having occurred (code 12 shows up when certain
> other trouble codes get recorded), and
> 3.) it can take MANY more than 50 key-on cycles for code 12 to
> go away, even if no other trouble code is reported
> (probably depends on how one's driving patterns compare to
> the trigger conditions for running of the various "monitors").
>
> The word "monitor" seems to be jargon for any of various sets
>of firmware routines responsible for monitoring and|or testing various
>sets of subsystems within the vehicle.
>
> I hope this helps lessen the confusion over code 12.
>
> Happy JEEPing!
>
>
>-----
>Greg Thoman: The opinions expressed herein are mine alone, and I am
> solely irresponsible for them.

Re: MIL Trouble Code 12 Meaning
 

This code occurs any time the engine controller microprocessor has a
low voltage reset. This occurs when the voltage AT THE ENGINE
COMPUTER goes below 6 volts.
This can occur during the first millisecond of engine cranking if the
battery or any of the connections that carry the starter current get
rusty and build up a higher than normal resistance. A few extra
milliohms will do this. During a start cycle the lowest battery
voltage occurs when the starter contactor closes but the starter and
engine has not yet begun to spin. This does not last very long, less
than a millisecond. You need to use a digital storage oscilloscope to
see this.

Get your self a good DVM, and a one amp or more load resistor. Then
learn what a 4 wire KELVIN resistance connection means. Then find
the high resistance that is causing the problem. ( E=IR ) Once you
understand what you are doing you can find the problem in less than a
hour most of the time.
John.


On 02 Nov 2003 06:34:30 GMT, thoman@frii.com wrote:

> Having long known that trouble code 12 (as flashed by the
>Malfunction Indicator Light, or MIL, AKA the "CHECK ENGINE" light
>after one does the start with key off, switch key on, key off,
>key on, key off, key on, leave key on and count groups of flashes
>until done, then turn key off) does not mean what my '96 Jeep Cherokee
>service manual says it means, I've been curious about it. I've just
>completed some homework and reached my own conclusion about what code
>12 really means.
>
> The widely-reported meaning is "battery recently disconnected"
>(supposedly within the last 50 key-on cycles), but I've known for a
>long time that this isn't quite right.
>
> I have now concluded that code 12 means "emissions systems not
>yet proven good". It seems to be reported when:
> a.) an emissions-related "monitor" has not yet run its testing,
> b.) an emissions-related trouble code is stored, or
> c.) ??? maybe some other circumstance I haven't learned yet,
> perhaps some numbers of consecutive passing runs of
> various emissions-related "monitors" after codes
> are cleared.
>
> This neatly explains why:
> 1.) a battery disconnect causes code 12 (all "monitors" would then
> be flagged as not yet having run their tests),
> 2.) code 12 can appear without a battery disconnect or loss of
> connection having occurred (code 12 shows up when certain
> other trouble codes get recorded), and
> 3.) it can take MANY more than 50 key-on cycles for code 12 to
> go away, even if no other trouble code is reported
> (probably depends on how one's driving patterns compare to
> the trigger conditions for running of the various "monitors").
>
> The word "monitor" seems to be jargon for any of various sets
>of firmware routines responsible for monitoring and|or testing various
>sets of subsystems within the vehicle.
>
> I hope this helps lessen the confusion over code 12.
>
> Happy JEEPing!
>
>
>-----
>Greg Thoman: The opinions expressed herein are mine alone, and I am
> solely irresponsible for them.

Re: MIL Trouble Code 12 Meaning
 

The main thing is, don't let the 12 code bother you too much. Unless
you know you have a battery/electrial problem,the code is a common
one.

Re: MIL Trouble Code 12 Meaning
 

The main thing is, don't let the 12 code bother you too much. Unless
you know you have a battery/electrial problem,the code is a common
one.

Re: MIL Trouble Code 12 Meaning
 

The main thing is, don't let the 12 code bother you too much. Unless
you know you have a battery/electrial problem,the code is a common
one.