Jeep won't start after installation of new deck
10-04-2004, 04:24 PM
#11
Guest
Posts: n/a
Re: Jeep won't start after installation of new deck
My first guess is that the alarm system has a starter-bypass circuit to
disable the starter when the alarm is set. If the alarm controller was
confused, it could think it was still armed, and that would lock out the
starter circuit.
Of course, I am assuming you have not cut into the Safety Switch on the
clutch.
"Ethan" <ethanjones@gmail.com> wrote in message
news:31b69f22.0410031917.20a730e1@posting.google.c om...
> I have a 89 Wrangler 4.2l that I installed a new CD deck into today.
> The installation went without a hitch, except for the fact that the
> wires that connect to the LED light for the alarm (LED doesn't work)
> broke loose. After hooking everything back up and putting the dash
> back together, the Jeep would not start. I turned it to the "On"
> position and everything lights up, radio works, blower works, etc.
> Turn to "Start" postion, nothing. Not even trying to crank over. In
> the "On" position the battery is reading around 8 volts, so I tried to
> jump the Jeep with my Suburban, but had no luck with that either. I am
> starting to think that my battery is shot or that something with the
> wires to the LED light for the alarm caused it to flip out. I have not
> had a need or desire to use the alarm since I purchased the Jeep, so I
> do not know how it works, only that the person I purchased it from a
> couple of months ago said that it worked. It is supposed to have a
> starter disable. The model is a CodeAlarm 707 plus 4.0. I tried
> messing with the alarm wires a little to see if that was the issue but
> no luck. I am leaning towards the ignition kill in the alarm as the
> culprit, but with only 8 volts on the battery, it could be that too. I
> could not find any info on the alarm online, so I am going to call a
> car security shop tomorrow to find out more info on it. Any
> suggestions would be much appreciated.
>
> Ethan
disable the starter when the alarm is set. If the alarm controller was
confused, it could think it was still armed, and that would lock out the
starter circuit.
Of course, I am assuming you have not cut into the Safety Switch on the
clutch.
"Ethan" <ethanjones@gmail.com> wrote in message
news:31b69f22.0410031917.20a730e1@posting.google.c om...
> I have a 89 Wrangler 4.2l that I installed a new CD deck into today.
> The installation went without a hitch, except for the fact that the
> wires that connect to the LED light for the alarm (LED doesn't work)
> broke loose. After hooking everything back up and putting the dash
> back together, the Jeep would not start. I turned it to the "On"
> position and everything lights up, radio works, blower works, etc.
> Turn to "Start" postion, nothing. Not even trying to crank over. In
> the "On" position the battery is reading around 8 volts, so I tried to
> jump the Jeep with my Suburban, but had no luck with that either. I am
> starting to think that my battery is shot or that something with the
> wires to the LED light for the alarm caused it to flip out. I have not
> had a need or desire to use the alarm since I purchased the Jeep, so I
> do not know how it works, only that the person I purchased it from a
> couple of months ago said that it worked. It is supposed to have a
> starter disable. The model is a CodeAlarm 707 plus 4.0. I tried
> messing with the alarm wires a little to see if that was the issue but
> no luck. I am leaning towards the ignition kill in the alarm as the
> culprit, but with only 8 volts on the battery, it could be that too. I
> could not find any info on the alarm online, so I am going to call a
> car security shop tomorrow to find out more info on it. Any
> suggestions would be much appreciated.
>
> Ethan
10-04-2004, 04:24 PM
#12
Guest
Posts: n/a
Re: Jeep won't start after installation of new deck
My first guess is that the alarm system has a starter-bypass circuit to
disable the starter when the alarm is set. If the alarm controller was
confused, it could think it was still armed, and that would lock out the
starter circuit.
Of course, I am assuming you have not cut into the Safety Switch on the
clutch.
"Ethan" <ethanjones@gmail.com> wrote in message
news:31b69f22.0410031917.20a730e1@posting.google.c om...
> I have a 89 Wrangler 4.2l that I installed a new CD deck into today.
> The installation went without a hitch, except for the fact that the
> wires that connect to the LED light for the alarm (LED doesn't work)
> broke loose. After hooking everything back up and putting the dash
> back together, the Jeep would not start. I turned it to the "On"
> position and everything lights up, radio works, blower works, etc.
> Turn to "Start" postion, nothing. Not even trying to crank over. In
> the "On" position the battery is reading around 8 volts, so I tried to
> jump the Jeep with my Suburban, but had no luck with that either. I am
> starting to think that my battery is shot or that something with the
> wires to the LED light for the alarm caused it to flip out. I have not
> had a need or desire to use the alarm since I purchased the Jeep, so I
> do not know how it works, only that the person I purchased it from a
> couple of months ago said that it worked. It is supposed to have a
> starter disable. The model is a CodeAlarm 707 plus 4.0. I tried
> messing with the alarm wires a little to see if that was the issue but
> no luck. I am leaning towards the ignition kill in the alarm as the
> culprit, but with only 8 volts on the battery, it could be that too. I
> could not find any info on the alarm online, so I am going to call a
> car security shop tomorrow to find out more info on it. Any
> suggestions would be much appreciated.
>
> Ethan
disable the starter when the alarm is set. If the alarm controller was
confused, it could think it was still armed, and that would lock out the
starter circuit.
Of course, I am assuming you have not cut into the Safety Switch on the
clutch.
"Ethan" <ethanjones@gmail.com> wrote in message
news:31b69f22.0410031917.20a730e1@posting.google.c om...
> I have a 89 Wrangler 4.2l that I installed a new CD deck into today.
> The installation went without a hitch, except for the fact that the
> wires that connect to the LED light for the alarm (LED doesn't work)
> broke loose. After hooking everything back up and putting the dash
> back together, the Jeep would not start. I turned it to the "On"
> position and everything lights up, radio works, blower works, etc.
> Turn to "Start" postion, nothing. Not even trying to crank over. In
> the "On" position the battery is reading around 8 volts, so I tried to
> jump the Jeep with my Suburban, but had no luck with that either. I am
> starting to think that my battery is shot or that something with the
> wires to the LED light for the alarm caused it to flip out. I have not
> had a need or desire to use the alarm since I purchased the Jeep, so I
> do not know how it works, only that the person I purchased it from a
> couple of months ago said that it worked. It is supposed to have a
> starter disable. The model is a CodeAlarm 707 plus 4.0. I tried
> messing with the alarm wires a little to see if that was the issue but
> no luck. I am leaning towards the ignition kill in the alarm as the
> culprit, but with only 8 volts on the battery, it could be that too. I
> could not find any info on the alarm online, so I am going to call a
> car security shop tomorrow to find out more info on it. Any
> suggestions would be much appreciated.
>
> Ethan
10-04-2004, 04:24 PM
#13
Guest
Posts: n/a
Re: Jeep won't start after installation of new deck
My first guess is that the alarm system has a starter-bypass circuit to
disable the starter when the alarm is set. If the alarm controller was
confused, it could think it was still armed, and that would lock out the
starter circuit.
Of course, I am assuming you have not cut into the Safety Switch on the
clutch.
"Ethan" <ethanjones@gmail.com> wrote in message
news:31b69f22.0410031917.20a730e1@posting.google.c om...
> I have a 89 Wrangler 4.2l that I installed a new CD deck into today.
> The installation went without a hitch, except for the fact that the
> wires that connect to the LED light for the alarm (LED doesn't work)
> broke loose. After hooking everything back up and putting the dash
> back together, the Jeep would not start. I turned it to the "On"
> position and everything lights up, radio works, blower works, etc.
> Turn to "Start" postion, nothing. Not even trying to crank over. In
> the "On" position the battery is reading around 8 volts, so I tried to
> jump the Jeep with my Suburban, but had no luck with that either. I am
> starting to think that my battery is shot or that something with the
> wires to the LED light for the alarm caused it to flip out. I have not
> had a need or desire to use the alarm since I purchased the Jeep, so I
> do not know how it works, only that the person I purchased it from a
> couple of months ago said that it worked. It is supposed to have a
> starter disable. The model is a CodeAlarm 707 plus 4.0. I tried
> messing with the alarm wires a little to see if that was the issue but
> no luck. I am leaning towards the ignition kill in the alarm as the
> culprit, but with only 8 volts on the battery, it could be that too. I
> could not find any info on the alarm online, so I am going to call a
> car security shop tomorrow to find out more info on it. Any
> suggestions would be much appreciated.
>
> Ethan
disable the starter when the alarm is set. If the alarm controller was
confused, it could think it was still armed, and that would lock out the
starter circuit.
Of course, I am assuming you have not cut into the Safety Switch on the
clutch.
"Ethan" <ethanjones@gmail.com> wrote in message
news:31b69f22.0410031917.20a730e1@posting.google.c om...
> I have a 89 Wrangler 4.2l that I installed a new CD deck into today.
> The installation went without a hitch, except for the fact that the
> wires that connect to the LED light for the alarm (LED doesn't work)
> broke loose. After hooking everything back up and putting the dash
> back together, the Jeep would not start. I turned it to the "On"
> position and everything lights up, radio works, blower works, etc.
> Turn to "Start" postion, nothing. Not even trying to crank over. In
> the "On" position the battery is reading around 8 volts, so I tried to
> jump the Jeep with my Suburban, but had no luck with that either. I am
> starting to think that my battery is shot or that something with the
> wires to the LED light for the alarm caused it to flip out. I have not
> had a need or desire to use the alarm since I purchased the Jeep, so I
> do not know how it works, only that the person I purchased it from a
> couple of months ago said that it worked. It is supposed to have a
> starter disable. The model is a CodeAlarm 707 plus 4.0. I tried
> messing with the alarm wires a little to see if that was the issue but
> no luck. I am leaning towards the ignition kill in the alarm as the
> culprit, but with only 8 volts on the battery, it could be that too. I
> could not find any info on the alarm online, so I am going to call a
> car security shop tomorrow to find out more info on it. Any
> suggestions would be much appreciated.
>
> Ethan
10-04-2004, 06:11 PM
#14
Guest
Posts: n/a
Re: Jeep won't start after installation of new deck
Ethan did pass the time by typing:
> I did not disconnect the battery during the installation. There was a
> inline fuse for the power line, so I pulled the fuse during
> installation. I did disconnect the battery to repair the power line
> going to the LED light. As I was reassembling the dash I noticed that
> a wire was arcing and it was the positive for the LED light. The
> inside of the wire was stripped near the metal part of the dash
> causing the arc. I repaired the wire and hooked the battery back up.
Try this.
Disconnect the battery ground.
Turn all accessories off
Turn the headlights off
Close the doors
Put ignition key in and turn to ON.
Connect the battery.
That will tell the alarm system the owner
is reconnecting power and will reset the
alarm system.
Your going to draw a teeny spark so its safer
to set a damp cloth over the battery vents.
--
DougW
> I did not disconnect the battery during the installation. There was a
> inline fuse for the power line, so I pulled the fuse during
> installation. I did disconnect the battery to repair the power line
> going to the LED light. As I was reassembling the dash I noticed that
> a wire was arcing and it was the positive for the LED light. The
> inside of the wire was stripped near the metal part of the dash
> causing the arc. I repaired the wire and hooked the battery back up.
Try this.
Disconnect the battery ground.
Turn all accessories off
Turn the headlights off
Close the doors
Put ignition key in and turn to ON.
Connect the battery.
That will tell the alarm system the owner
is reconnecting power and will reset the
alarm system.
Your going to draw a teeny spark so its safer
to set a damp cloth over the battery vents.
--
DougW
10-04-2004, 06:11 PM
#15
Guest
Posts: n/a
Re: Jeep won't start after installation of new deck
Ethan did pass the time by typing:
> I did not disconnect the battery during the installation. There was a
> inline fuse for the power line, so I pulled the fuse during
> installation. I did disconnect the battery to repair the power line
> going to the LED light. As I was reassembling the dash I noticed that
> a wire was arcing and it was the positive for the LED light. The
> inside of the wire was stripped near the metal part of the dash
> causing the arc. I repaired the wire and hooked the battery back up.
Try this.
Disconnect the battery ground.
Turn all accessories off
Turn the headlights off
Close the doors
Put ignition key in and turn to ON.
Connect the battery.
That will tell the alarm system the owner
is reconnecting power and will reset the
alarm system.
Your going to draw a teeny spark so its safer
to set a damp cloth over the battery vents.
--
DougW
> I did not disconnect the battery during the installation. There was a
> inline fuse for the power line, so I pulled the fuse during
> installation. I did disconnect the battery to repair the power line
> going to the LED light. As I was reassembling the dash I noticed that
> a wire was arcing and it was the positive for the LED light. The
> inside of the wire was stripped near the metal part of the dash
> causing the arc. I repaired the wire and hooked the battery back up.
Try this.
Disconnect the battery ground.
Turn all accessories off
Turn the headlights off
Close the doors
Put ignition key in and turn to ON.
Connect the battery.
That will tell the alarm system the owner
is reconnecting power and will reset the
alarm system.
Your going to draw a teeny spark so its safer
to set a damp cloth over the battery vents.
--
DougW
10-04-2004, 06:11 PM
#16
Guest
Posts: n/a
Re: Jeep won't start after installation of new deck
Ethan did pass the time by typing:
> I did not disconnect the battery during the installation. There was a
> inline fuse for the power line, so I pulled the fuse during
> installation. I did disconnect the battery to repair the power line
> going to the LED light. As I was reassembling the dash I noticed that
> a wire was arcing and it was the positive for the LED light. The
> inside of the wire was stripped near the metal part of the dash
> causing the arc. I repaired the wire and hooked the battery back up.
Try this.
Disconnect the battery ground.
Turn all accessories off
Turn the headlights off
Close the doors
Put ignition key in and turn to ON.
Connect the battery.
That will tell the alarm system the owner
is reconnecting power and will reset the
alarm system.
Your going to draw a teeny spark so its safer
to set a damp cloth over the battery vents.
--
DougW
> I did not disconnect the battery during the installation. There was a
> inline fuse for the power line, so I pulled the fuse during
> installation. I did disconnect the battery to repair the power line
> going to the LED light. As I was reassembling the dash I noticed that
> a wire was arcing and it was the positive for the LED light. The
> inside of the wire was stripped near the metal part of the dash
> causing the arc. I repaired the wire and hooked the battery back up.
Try this.
Disconnect the battery ground.
Turn all accessories off
Turn the headlights off
Close the doors
Put ignition key in and turn to ON.
Connect the battery.
That will tell the alarm system the owner
is reconnecting power and will reset the
alarm system.
Your going to draw a teeny spark so its safer
to set a damp cloth over the battery vents.
--
DougW
10-08-2004, 04:09 PM
#17
Guest
Posts: n/a
Re: Jeep won't start after installation of new deck
Thanks for everyone's suggestions. The issue was the alarm. I got ahold
the manufacturer tech support and they directed me how to override the
alarm so I could get the jeep started again. I had the alarm removed
yesterday.
CRWLR wrote:
> My first guess is that the alarm system has a starter-bypass circuit to
> disable the starter when the alarm is set. If the alarm controller was
> confused, it could think it was still armed, and that would lock out the
> starter circuit.
>
> Of course, I am assuming you have not cut into the Safety Switch on the
> clutch.
>
>
>
>
> "Ethan" <ethanjones@gmail.com> wrote in message
> news:31b69f22.0410031917.20a730e1@posting.google.c om...
>
>>I have a 89 Wrangler 4.2l that I installed a new CD deck into today.
>>The installation went without a hitch, except for the fact that the
>>wires that connect to the LED light for the alarm (LED doesn't work)
>>broke loose. After hooking everything back up and putting the dash
>>back together, the Jeep would not start. I turned it to the "On"
>>position and everything lights up, radio works, blower works, etc.
>>Turn to "Start" postion, nothing. Not even trying to crank over. In
>>the "On" position the battery is reading around 8 volts, so I tried to
>>jump the Jeep with my Suburban, but had no luck with that either. I am
>>starting to think that my battery is shot or that something with the
>>wires to the LED light for the alarm caused it to flip out. I have not
>>had a need or desire to use the alarm since I purchased the Jeep, so I
>>do not know how it works, only that the person I purchased it from a
>>couple of months ago said that it worked. It is supposed to have a
>>starter disable. The model is a CodeAlarm 707 plus 4.0. I tried
>>messing with the alarm wires a little to see if that was the issue but
>>no luck. I am leaning towards the ignition kill in the alarm as the
>>culprit, but with only 8 volts on the battery, it could be that too. I
>>could not find any info on the alarm online, so I am going to call a
>>car security shop tomorrow to find out more info on it. Any
>>suggestions would be much appreciated.
>>
>>Ethan
>
>
>
the manufacturer tech support and they directed me how to override the
alarm so I could get the jeep started again. I had the alarm removed
yesterday.
CRWLR wrote:
> My first guess is that the alarm system has a starter-bypass circuit to
> disable the starter when the alarm is set. If the alarm controller was
> confused, it could think it was still armed, and that would lock out the
> starter circuit.
>
> Of course, I am assuming you have not cut into the Safety Switch on the
> clutch.
>
>
>
>
> "Ethan" <ethanjones@gmail.com> wrote in message
> news:31b69f22.0410031917.20a730e1@posting.google.c om...
>
>>I have a 89 Wrangler 4.2l that I installed a new CD deck into today.
>>The installation went without a hitch, except for the fact that the
>>wires that connect to the LED light for the alarm (LED doesn't work)
>>broke loose. After hooking everything back up and putting the dash
>>back together, the Jeep would not start. I turned it to the "On"
>>position and everything lights up, radio works, blower works, etc.
>>Turn to "Start" postion, nothing. Not even trying to crank over. In
>>the "On" position the battery is reading around 8 volts, so I tried to
>>jump the Jeep with my Suburban, but had no luck with that either. I am
>>starting to think that my battery is shot or that something with the
>>wires to the LED light for the alarm caused it to flip out. I have not
>>had a need or desire to use the alarm since I purchased the Jeep, so I
>>do not know how it works, only that the person I purchased it from a
>>couple of months ago said that it worked. It is supposed to have a
>>starter disable. The model is a CodeAlarm 707 plus 4.0. I tried
>>messing with the alarm wires a little to see if that was the issue but
>>no luck. I am leaning towards the ignition kill in the alarm as the
>>culprit, but with only 8 volts on the battery, it could be that too. I
>>could not find any info on the alarm online, so I am going to call a
>>car security shop tomorrow to find out more info on it. Any
>>suggestions would be much appreciated.
>>
>>Ethan
>
>
>
10-08-2004, 04:09 PM
#18
Guest
Posts: n/a
Re: Jeep won't start after installation of new deck
Thanks for everyone's suggestions. The issue was the alarm. I got ahold
the manufacturer tech support and they directed me how to override the
alarm so I could get the jeep started again. I had the alarm removed
yesterday.
CRWLR wrote:
> My first guess is that the alarm system has a starter-bypass circuit to
> disable the starter when the alarm is set. If the alarm controller was
> confused, it could think it was still armed, and that would lock out the
> starter circuit.
>
> Of course, I am assuming you have not cut into the Safety Switch on the
> clutch.
>
>
>
>
> "Ethan" <ethanjones@gmail.com> wrote in message
> news:31b69f22.0410031917.20a730e1@posting.google.c om...
>
>>I have a 89 Wrangler 4.2l that I installed a new CD deck into today.
>>The installation went without a hitch, except for the fact that the
>>wires that connect to the LED light for the alarm (LED doesn't work)
>>broke loose. After hooking everything back up and putting the dash
>>back together, the Jeep would not start. I turned it to the "On"
>>position and everything lights up, radio works, blower works, etc.
>>Turn to "Start" postion, nothing. Not even trying to crank over. In
>>the "On" position the battery is reading around 8 volts, so I tried to
>>jump the Jeep with my Suburban, but had no luck with that either. I am
>>starting to think that my battery is shot or that something with the
>>wires to the LED light for the alarm caused it to flip out. I have not
>>had a need or desire to use the alarm since I purchased the Jeep, so I
>>do not know how it works, only that the person I purchased it from a
>>couple of months ago said that it worked. It is supposed to have a
>>starter disable. The model is a CodeAlarm 707 plus 4.0. I tried
>>messing with the alarm wires a little to see if that was the issue but
>>no luck. I am leaning towards the ignition kill in the alarm as the
>>culprit, but with only 8 volts on the battery, it could be that too. I
>>could not find any info on the alarm online, so I am going to call a
>>car security shop tomorrow to find out more info on it. Any
>>suggestions would be much appreciated.
>>
>>Ethan
>
>
>
the manufacturer tech support and they directed me how to override the
alarm so I could get the jeep started again. I had the alarm removed
yesterday.
CRWLR wrote:
> My first guess is that the alarm system has a starter-bypass circuit to
> disable the starter when the alarm is set. If the alarm controller was
> confused, it could think it was still armed, and that would lock out the
> starter circuit.
>
> Of course, I am assuming you have not cut into the Safety Switch on the
> clutch.
>
>
>
>
> "Ethan" <ethanjones@gmail.com> wrote in message
> news:31b69f22.0410031917.20a730e1@posting.google.c om...
>
>>I have a 89 Wrangler 4.2l that I installed a new CD deck into today.
>>The installation went without a hitch, except for the fact that the
>>wires that connect to the LED light for the alarm (LED doesn't work)
>>broke loose. After hooking everything back up and putting the dash
>>back together, the Jeep would not start. I turned it to the "On"
>>position and everything lights up, radio works, blower works, etc.
>>Turn to "Start" postion, nothing. Not even trying to crank over. In
>>the "On" position the battery is reading around 8 volts, so I tried to
>>jump the Jeep with my Suburban, but had no luck with that either. I am
>>starting to think that my battery is shot or that something with the
>>wires to the LED light for the alarm caused it to flip out. I have not
>>had a need or desire to use the alarm since I purchased the Jeep, so I
>>do not know how it works, only that the person I purchased it from a
>>couple of months ago said that it worked. It is supposed to have a
>>starter disable. The model is a CodeAlarm 707 plus 4.0. I tried
>>messing with the alarm wires a little to see if that was the issue but
>>no luck. I am leaning towards the ignition kill in the alarm as the
>>culprit, but with only 8 volts on the battery, it could be that too. I
>>could not find any info on the alarm online, so I am going to call a
>>car security shop tomorrow to find out more info on it. Any
>>suggestions would be much appreciated.
>>
>>Ethan
>
>
>
10-08-2004, 04:09 PM
#19
Guest
Posts: n/a
Re: Jeep won't start after installation of new deck
Thanks for everyone's suggestions. The issue was the alarm. I got ahold
the manufacturer tech support and they directed me how to override the
alarm so I could get the jeep started again. I had the alarm removed
yesterday.
CRWLR wrote:
> My first guess is that the alarm system has a starter-bypass circuit to
> disable the starter when the alarm is set. If the alarm controller was
> confused, it could think it was still armed, and that would lock out the
> starter circuit.
>
> Of course, I am assuming you have not cut into the Safety Switch on the
> clutch.
>
>
>
>
> "Ethan" <ethanjones@gmail.com> wrote in message
> news:31b69f22.0410031917.20a730e1@posting.google.c om...
>
>>I have a 89 Wrangler 4.2l that I installed a new CD deck into today.
>>The installation went without a hitch, except for the fact that the
>>wires that connect to the LED light for the alarm (LED doesn't work)
>>broke loose. After hooking everything back up and putting the dash
>>back together, the Jeep would not start. I turned it to the "On"
>>position and everything lights up, radio works, blower works, etc.
>>Turn to "Start" postion, nothing. Not even trying to crank over. In
>>the "On" position the battery is reading around 8 volts, so I tried to
>>jump the Jeep with my Suburban, but had no luck with that either. I am
>>starting to think that my battery is shot or that something with the
>>wires to the LED light for the alarm caused it to flip out. I have not
>>had a need or desire to use the alarm since I purchased the Jeep, so I
>>do not know how it works, only that the person I purchased it from a
>>couple of months ago said that it worked. It is supposed to have a
>>starter disable. The model is a CodeAlarm 707 plus 4.0. I tried
>>messing with the alarm wires a little to see if that was the issue but
>>no luck. I am leaning towards the ignition kill in the alarm as the
>>culprit, but with only 8 volts on the battery, it could be that too. I
>>could not find any info on the alarm online, so I am going to call a
>>car security shop tomorrow to find out more info on it. Any
>>suggestions would be much appreciated.
>>
>>Ethan
>
>
>
the manufacturer tech support and they directed me how to override the
alarm so I could get the jeep started again. I had the alarm removed
yesterday.
CRWLR wrote:
> My first guess is that the alarm system has a starter-bypass circuit to
> disable the starter when the alarm is set. If the alarm controller was
> confused, it could think it was still armed, and that would lock out the
> starter circuit.
>
> Of course, I am assuming you have not cut into the Safety Switch on the
> clutch.
>
>
>
>
> "Ethan" <ethanjones@gmail.com> wrote in message
> news:31b69f22.0410031917.20a730e1@posting.google.c om...
>
>>I have a 89 Wrangler 4.2l that I installed a new CD deck into today.
>>The installation went without a hitch, except for the fact that the
>>wires that connect to the LED light for the alarm (LED doesn't work)
>>broke loose. After hooking everything back up and putting the dash
>>back together, the Jeep would not start. I turned it to the "On"
>>position and everything lights up, radio works, blower works, etc.
>>Turn to "Start" postion, nothing. Not even trying to crank over. In
>>the "On" position the battery is reading around 8 volts, so I tried to
>>jump the Jeep with my Suburban, but had no luck with that either. I am
>>starting to think that my battery is shot or that something with the
>>wires to the LED light for the alarm caused it to flip out. I have not
>>had a need or desire to use the alarm since I purchased the Jeep, so I
>>do not know how it works, only that the person I purchased it from a
>>couple of months ago said that it worked. It is supposed to have a
>>starter disable. The model is a CodeAlarm 707 plus 4.0. I tried
>>messing with the alarm wires a little to see if that was the issue but
>>no luck. I am leaning towards the ignition kill in the alarm as the
>>culprit, but with only 8 volts on the battery, it could be that too. I
>>could not find any info on the alarm online, so I am going to call a
>>car security shop tomorrow to find out more info on it. Any
>>suggestions would be much appreciated.
>>
>>Ethan
>
>
>
10-08-2004, 04:17 PM
#20
Guest
Posts: n/a
Re: Jeep won't start after installation of new deck
And, where do you live? ;-)
Ethan Jones wrote:
>
> Thanks for everyone's suggestions. The issue was the alarm. I got ahold
> the manufacturer tech support and they directed me how to override the
> alarm so I could get the jeep started again. I had the alarm removed
> yesterday.
Ethan Jones wrote:
>
> Thanks for everyone's suggestions. The issue was the alarm. I got ahold
> the manufacturer tech support and they directed me how to override the
> alarm so I could get the jeep started again. I had the alarm removed
> yesterday.