On Sat, 6 Mar 2004 23:37:06 UTC "DougW" <post.replies@invalid.address>
wrote:

> Will Honea did pass the time by typing:
>
> > On the XJ/MJ I was able to swap it out from the top. I used a $8-10
> > universal puller from Harbor Freight but it's tight enough on those
> > models that you're probably going to loose a little skin of your
> > knuckles as they get friendly with the radiator when you work with the
> > puller.
>
> just got back from Steve's Tools (our local version of HF) measured
> the puller and it's center bolt/screw. It is about 1" longer than
> the distance between the balancer and the radiator. ZJs don't have
> squat for room in there. Almost wish I had the old Chevy back.
> Does that long center screw slide down into the crank? If so it might
> just fit.

I don't know where you measured - the bolt comes out and don't forget
to take that big flat washer that's under the bolt out BEFORE you try
the puller! Once the bolt is out, there is a centering hole in the
end of the crank that the puller sits into. Mine is fairly long and
the 88 MJ is set up so that the puller screw rides just uder the
radiator. That means you are turning the puller with your knuckles
right next to the radiator - and that sucker can bite.

I drilled a couple of holes in a 3 foot piece of 5/16 bar stock I had
laying around and bolted that to 2 of the smaller (about 1/4 inch, but
metric 6-8 mm?) holes in the middle part of the damper. That rotated
over against the frame and held things nice and solid while I used a
big breaker bar and socket on the bolt. Same for touquing it back.
If you do use the puiller, be careful with the bolts that you use to
attach it to the damper. Mine were drilled all the way thru and if
the bolts are too long you can punch them into the timing cover.
That's a standard RH bolt, BTW. Also, it's a lot simpler to see what
you need to do if you parctice the setup on the new one to get an idea
of where all the holes are. DON'T FORGET THAT WASHER - someone here
worked for a considerable time before he got around to taking that
sucker out and was amazed how easy it was after that <g>.

Given a choice, I would have pulled the radiator and used an impact
wrench but every one I did had a/c so I would have had a skid plate
and the condensor to pull in addition to the radiator - easiler to
take a little time and make the holding tool.

>
> > One big problem: you will probably need some sort of a bar to
> > bolt onto the damper so that you can jam that against the frame while
> > you loosen/torque the bolt that holds it onto the crank. I couldn't
> > get the thing to hold well enough with the transmission in gear to
> > break it free.
>
> Yea.. and with an auto trany like mine it won't hold it anyway. :/
> My plan was to use an air wrench on it. Usually that will break things
> loose. Speaking of breaking loose.. is that a left or right handed thread?
> Amazing how easier it is if your turning it the proper way. :]
>
> > One of my manuals says you can jam a screw drive or
> > pry bar against 2 bolts in the puller holes - on the three I remember
> > doing, that just twisted the bolts up and was totally a waste of time.
>
> Hmm.. This is looking more and more like a dealership job. Gonna find
> out how much that costs Monday. Might not be worth my time and effort
> if it's gonna be a real pain. (then again that means it will also be
> expensive) :/ We will see where my pain threshold is.
>


--
Will Honea <whonea@codenet.net>

 

I will second that, some of those can be a real bugger to get off. I
have seen and heard of lots of broken pullers over the years.

To get the main bolt, you can use a long wrench braced against the frame
and the starter motor.

Basically if the pulley isn't wobbling and if the timing mark is still
correct, then I would leave it until I 'had' to take it off or something
else off.

Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's

Cherokee-LTD wrote:
>
> Hey Doug,
>
> FWIW mine came off rather easy but that is probably because the engine was
> out of the XJ. Had I been tight for space working in a snowstorm you can bet
> your *** it would have been seized on.
>
> I'm not so sure I'd sweat that HB right now - I've seen a lot worse! You've
> discovered wear, keep an eye on it - you may not need to change until your
> convenience... like when you have to do a water pump, rad, t-chain etc.
> -Brian
>
> "L.W. (ßill) ------ III" <----------@***.net> wrote in message
> news:404A8028.45413CEC@***.net...
> : Hi Doug,
> : Might test it, by just removing it's bolt and give a couple tap
> : with a malt or even a hammer seeing you're not trying to save it. Ninety
> : percent of the ones I've pulled, pulling the puller out of the drawer
> : was just a waste of time.
> : God Bless America, ßill O|||||||O
> : mailto:-------------------- http://www.----------.com/
> :
> : DougW wrote:
> : >
> : > just got back from Steve's Tools (our local version of HF) measured
> : > the puller and it's center bolt/screw. It is about 1" longer than
> : > the distance between the balancer and the radiator. ZJs don't have
> : > squat for room in there. Almost wish I had the old Chevy back.
> : > Does that long center screw slide down into the crank? If so it might
> : > just fit.
> : >
> : > Yea.. and with an auto trany like mine it won't hold it anyway. :/
> : > My plan was to use an air wrench on it. Usually that will break things
> : > loose. Speaking of breaking loose.. is that a left or right handed
> thread?
> : > Amazing how easier it is if your turning it the proper way. :]
> : >
> : > Hmm.. This is looking more and more like a dealership job. Gonna find
> : > out how much that costs Monday. Might not be worth my time and effort
> : > if it's gonna be a real pain. (then again that means it will also be
> : > expensive) :/ We will see where my pain threshold is.
> : >
> : > --
> : > DougW
> : > Jeep 1, Wallet 0

 

I will second that, some of those can be a real bugger to get off. I
have seen and heard of lots of broken pullers over the years.

To get the main bolt, you can use a long wrench braced against the frame
and the starter motor.

Basically if the pulley isn't wobbling and if the timing mark is still
correct, then I would leave it until I 'had' to take it off or something
else off.

Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's

Cherokee-LTD wrote:
>
> Hey Doug,
>
> FWIW mine came off rather easy but that is probably because the engine was
> out of the XJ. Had I been tight for space working in a snowstorm you can bet
> your *** it would have been seized on.
>
> I'm not so sure I'd sweat that HB right now - I've seen a lot worse! You've
> discovered wear, keep an eye on it - you may not need to change until your
> convenience... like when you have to do a water pump, rad, t-chain etc.
> -Brian
>
> "L.W. (ßill) ------ III" <----------@***.net> wrote in message
> news:404A8028.45413CEC@***.net...
> : Hi Doug,
> : Might test it, by just removing it's bolt and give a couple tap
> : with a malt or even a hammer seeing you're not trying to save it. Ninety
> : percent of the ones I've pulled, pulling the puller out of the drawer
> : was just a waste of time.
> : God Bless America, ßill O|||||||O
> : mailto:-------------------- http://www.----------.com/
> :
> : DougW wrote:
> : >
> : > just got back from Steve's Tools (our local version of HF) measured
> : > the puller and it's center bolt/screw. It is about 1" longer than
> : > the distance between the balancer and the radiator. ZJs don't have
> : > squat for room in there. Almost wish I had the old Chevy back.
> : > Does that long center screw slide down into the crank? If so it might
> : > just fit.
> : >
> : > Yea.. and with an auto trany like mine it won't hold it anyway. :/
> : > My plan was to use an air wrench on it. Usually that will break things
> : > loose. Speaking of breaking loose.. is that a left or right handed
> thread?
> : > Amazing how easier it is if your turning it the proper way. :]
> : >
> : > Hmm.. This is looking more and more like a dealership job. Gonna find
> : > out how much that costs Monday. Might not be worth my time and effort
> : > if it's gonna be a real pain. (then again that means it will also be
> : > expensive) :/ We will see where my pain threshold is.
> : >
> : > --
> : > DougW
> : > Jeep 1, Wallet 0

 

I will second that, some of those can be a real bugger to get off. I
have seen and heard of lots of broken pullers over the years.

To get the main bolt, you can use a long wrench braced against the frame
and the starter motor.

Basically if the pulley isn't wobbling and if the timing mark is still
correct, then I would leave it until I 'had' to take it off or something
else off.

Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's

Cherokee-LTD wrote:
>
> Hey Doug,
>
> FWIW mine came off rather easy but that is probably because the engine was
> out of the XJ. Had I been tight for space working in a snowstorm you can bet
> your *** it would have been seized on.
>
> I'm not so sure I'd sweat that HB right now - I've seen a lot worse! You've
> discovered wear, keep an eye on it - you may not need to change until your
> convenience... like when you have to do a water pump, rad, t-chain etc.
> -Brian
>
> "L.W. (ßill) ------ III" <----------@***.net> wrote in message
> news:404A8028.45413CEC@***.net...
> : Hi Doug,
> : Might test it, by just removing it's bolt and give a couple tap
> : with a malt or even a hammer seeing you're not trying to save it. Ninety
> : percent of the ones I've pulled, pulling the puller out of the drawer
> : was just a waste of time.
> : God Bless America, ßill O|||||||O
> : mailto:-------------------- http://www.----------.com/
> :
> : DougW wrote:
> : >
> : > just got back from Steve's Tools (our local version of HF) measured
> : > the puller and it's center bolt/screw. It is about 1" longer than
> : > the distance between the balancer and the radiator. ZJs don't have
> : > squat for room in there. Almost wish I had the old Chevy back.
> : > Does that long center screw slide down into the crank? If so it might
> : > just fit.
> : >
> : > Yea.. and with an auto trany like mine it won't hold it anyway. :/
> : > My plan was to use an air wrench on it. Usually that will break things
> : > loose. Speaking of breaking loose.. is that a left or right handed
> thread?
> : > Amazing how easier it is if your turning it the proper way. :]
> : >
> : > Hmm.. This is looking more and more like a dealership job. Gonna find
> : > out how much that costs Monday. Might not be worth my time and effort
> : > if it's gonna be a real pain. (then again that means it will also be
> : > expensive) :/ We will see where my pain threshold is.
> : >
> : > --
> : > DougW
> : > Jeep 1, Wallet 0