Finished lift kit, now have drive shaft vibration
#41
Guest
Posts: n/a
Re: Finished lift kit, now have drive shaft vibration
The SYE is not needed with your D300 tcase.
You need to drop the tcase with the shims, or get a double-cardan
driveshaft. If you already have a double cardan (CV) driveshaft, then you
have broken the ball thingie in the center. A double cardan has two Ujoints
at the tcase end, and in between these two ujoints is another part that is
basically a balljoint with a small but heavy spring inside. The spring acts
to keep the two ujoints lined up, but if the ball portion of this joint
breaks, then the ujoints can flop around relative to each other, and this
will set up the vibrations you are talking about.
One other thing you might need is to install those wedge-shaped shims
between the axle and the springs. This will tilt the pumpkin up a few
degrees and make the angles of the driveshaft a little flatter.
"William Oliveri" <wuji@bigvalley.net> wrote in message
news:c0g904$16tn5g$1@ID-193866.news.uni-berlin.de...
> Is not the SYE kit for a automatic tranny or not needed for a CJ7? Please
> correct me if I'm wrong.
>
>
>
>
> "Bert Boks" <tandartsbus@hotmail.com> wrote in message
> news:402b6090$0$139$e4fe514c@dreader7.news.xs4all. nl...
> > I had exactly the same problem. Only I didnot know where to put them 6
> large
> > shims I got left.....
> > After I dropped the transfer case with those Shims, the problem was
gone.
> >
> > There is another solution to that problem, the Slip Yoke Eliminator Kit.
> It
> > helps to give you ground clearence, but it will cost you an arm and a
leg.
> >
> >
> > --
> > --
> > Greetings from the Netherlands,
> >
> > Bert
> >
> >
> > "William Oliveri" <wuji@bigvalley.net> schreef in bericht
> > news:c0f6ea$166d50$1@ID-193866.news.uni-berlin.de...
> > > First I put the lift kit (4" superlift kit) on the front end of my 83
> CJ7
> > > and drove it till the next weekend when I put the rear half on.
> > Everything
> > > was fine with only the front on. Now, with the rear on I get a
> vibration
> > > from the drive shaft it seems at around 40 and up. The when I let off
> the
> > > gas I hear a noise like a 10 speed bike would make when you are
coasting
> > > only heavier, click click click click.... etc.
> > >
> > > The kit came with a transfer case drop kit but I didn't install it.
> > Others
> > > I have talked to said they didn't use the transfer case drop kit.
> > >
> > > Has anyone else had this problem or can anyone give a comment or help?
> > >
> > > Thanks,
> > >
> > >
> >
> >
>
>
You need to drop the tcase with the shims, or get a double-cardan
driveshaft. If you already have a double cardan (CV) driveshaft, then you
have broken the ball thingie in the center. A double cardan has two Ujoints
at the tcase end, and in between these two ujoints is another part that is
basically a balljoint with a small but heavy spring inside. The spring acts
to keep the two ujoints lined up, but if the ball portion of this joint
breaks, then the ujoints can flop around relative to each other, and this
will set up the vibrations you are talking about.
One other thing you might need is to install those wedge-shaped shims
between the axle and the springs. This will tilt the pumpkin up a few
degrees and make the angles of the driveshaft a little flatter.
"William Oliveri" <wuji@bigvalley.net> wrote in message
news:c0g904$16tn5g$1@ID-193866.news.uni-berlin.de...
> Is not the SYE kit for a automatic tranny or not needed for a CJ7? Please
> correct me if I'm wrong.
>
>
>
>
> "Bert Boks" <tandartsbus@hotmail.com> wrote in message
> news:402b6090$0$139$e4fe514c@dreader7.news.xs4all. nl...
> > I had exactly the same problem. Only I didnot know where to put them 6
> large
> > shims I got left.....
> > After I dropped the transfer case with those Shims, the problem was
gone.
> >
> > There is another solution to that problem, the Slip Yoke Eliminator Kit.
> It
> > helps to give you ground clearence, but it will cost you an arm and a
leg.
> >
> >
> > --
> > --
> > Greetings from the Netherlands,
> >
> > Bert
> >
> >
> > "William Oliveri" <wuji@bigvalley.net> schreef in bericht
> > news:c0f6ea$166d50$1@ID-193866.news.uni-berlin.de...
> > > First I put the lift kit (4" superlift kit) on the front end of my 83
> CJ7
> > > and drove it till the next weekend when I put the rear half on.
> > Everything
> > > was fine with only the front on. Now, with the rear on I get a
> vibration
> > > from the drive shaft it seems at around 40 and up. The when I let off
> the
> > > gas I hear a noise like a 10 speed bike would make when you are
coasting
> > > only heavier, click click click click.... etc.
> > >
> > > The kit came with a transfer case drop kit but I didn't install it.
> > Others
> > > I have talked to said they didn't use the transfer case drop kit.
> > >
> > > Has anyone else had this problem or can anyone give a comment or help?
> > >
> > > Thanks,
> > >
> > >
> >
> >
>
>
#42
Guest
Posts: n/a
Re: Finished lift kit, now have drive shaft vibration
The SYE is not needed with your D300 tcase.
You need to drop the tcase with the shims, or get a double-cardan
driveshaft. If you already have a double cardan (CV) driveshaft, then you
have broken the ball thingie in the center. A double cardan has two Ujoints
at the tcase end, and in between these two ujoints is another part that is
basically a balljoint with a small but heavy spring inside. The spring acts
to keep the two ujoints lined up, but if the ball portion of this joint
breaks, then the ujoints can flop around relative to each other, and this
will set up the vibrations you are talking about.
One other thing you might need is to install those wedge-shaped shims
between the axle and the springs. This will tilt the pumpkin up a few
degrees and make the angles of the driveshaft a little flatter.
"William Oliveri" <wuji@bigvalley.net> wrote in message
news:c0g904$16tn5g$1@ID-193866.news.uni-berlin.de...
> Is not the SYE kit for a automatic tranny or not needed for a CJ7? Please
> correct me if I'm wrong.
>
>
>
>
> "Bert Boks" <tandartsbus@hotmail.com> wrote in message
> news:402b6090$0$139$e4fe514c@dreader7.news.xs4all. nl...
> > I had exactly the same problem. Only I didnot know where to put them 6
> large
> > shims I got left.....
> > After I dropped the transfer case with those Shims, the problem was
gone.
> >
> > There is another solution to that problem, the Slip Yoke Eliminator Kit.
> It
> > helps to give you ground clearence, but it will cost you an arm and a
leg.
> >
> >
> > --
> > --
> > Greetings from the Netherlands,
> >
> > Bert
> >
> >
> > "William Oliveri" <wuji@bigvalley.net> schreef in bericht
> > news:c0f6ea$166d50$1@ID-193866.news.uni-berlin.de...
> > > First I put the lift kit (4" superlift kit) on the front end of my 83
> CJ7
> > > and drove it till the next weekend when I put the rear half on.
> > Everything
> > > was fine with only the front on. Now, with the rear on I get a
> vibration
> > > from the drive shaft it seems at around 40 and up. The when I let off
> the
> > > gas I hear a noise like a 10 speed bike would make when you are
coasting
> > > only heavier, click click click click.... etc.
> > >
> > > The kit came with a transfer case drop kit but I didn't install it.
> > Others
> > > I have talked to said they didn't use the transfer case drop kit.
> > >
> > > Has anyone else had this problem or can anyone give a comment or help?
> > >
> > > Thanks,
> > >
> > >
> >
> >
>
>
You need to drop the tcase with the shims, or get a double-cardan
driveshaft. If you already have a double cardan (CV) driveshaft, then you
have broken the ball thingie in the center. A double cardan has two Ujoints
at the tcase end, and in between these two ujoints is another part that is
basically a balljoint with a small but heavy spring inside. The spring acts
to keep the two ujoints lined up, but if the ball portion of this joint
breaks, then the ujoints can flop around relative to each other, and this
will set up the vibrations you are talking about.
One other thing you might need is to install those wedge-shaped shims
between the axle and the springs. This will tilt the pumpkin up a few
degrees and make the angles of the driveshaft a little flatter.
"William Oliveri" <wuji@bigvalley.net> wrote in message
news:c0g904$16tn5g$1@ID-193866.news.uni-berlin.de...
> Is not the SYE kit for a automatic tranny or not needed for a CJ7? Please
> correct me if I'm wrong.
>
>
>
>
> "Bert Boks" <tandartsbus@hotmail.com> wrote in message
> news:402b6090$0$139$e4fe514c@dreader7.news.xs4all. nl...
> > I had exactly the same problem. Only I didnot know where to put them 6
> large
> > shims I got left.....
> > After I dropped the transfer case with those Shims, the problem was
gone.
> >
> > There is another solution to that problem, the Slip Yoke Eliminator Kit.
> It
> > helps to give you ground clearence, but it will cost you an arm and a
leg.
> >
> >
> > --
> > --
> > Greetings from the Netherlands,
> >
> > Bert
> >
> >
> > "William Oliveri" <wuji@bigvalley.net> schreef in bericht
> > news:c0f6ea$166d50$1@ID-193866.news.uni-berlin.de...
> > > First I put the lift kit (4" superlift kit) on the front end of my 83
> CJ7
> > > and drove it till the next weekend when I put the rear half on.
> > Everything
> > > was fine with only the front on. Now, with the rear on I get a
> vibration
> > > from the drive shaft it seems at around 40 and up. The when I let off
> the
> > > gas I hear a noise like a 10 speed bike would make when you are
coasting
> > > only heavier, click click click click.... etc.
> > >
> > > The kit came with a transfer case drop kit but I didn't install it.
> > Others
> > > I have talked to said they didn't use the transfer case drop kit.
> > >
> > > Has anyone else had this problem or can anyone give a comment or help?
> > >
> > > Thanks,
> > >
> > >
> >
> >
>
>
#43
Guest
Posts: n/a
Re: Finished lift kit, now have drive shaft vibration
The SYE is not needed with your D300 tcase.
You need to drop the tcase with the shims, or get a double-cardan
driveshaft. If you already have a double cardan (CV) driveshaft, then you
have broken the ball thingie in the center. A double cardan has two Ujoints
at the tcase end, and in between these two ujoints is another part that is
basically a balljoint with a small but heavy spring inside. The spring acts
to keep the two ujoints lined up, but if the ball portion of this joint
breaks, then the ujoints can flop around relative to each other, and this
will set up the vibrations you are talking about.
One other thing you might need is to install those wedge-shaped shims
between the axle and the springs. This will tilt the pumpkin up a few
degrees and make the angles of the driveshaft a little flatter.
"William Oliveri" <wuji@bigvalley.net> wrote in message
news:c0g904$16tn5g$1@ID-193866.news.uni-berlin.de...
> Is not the SYE kit for a automatic tranny or not needed for a CJ7? Please
> correct me if I'm wrong.
>
>
>
>
> "Bert Boks" <tandartsbus@hotmail.com> wrote in message
> news:402b6090$0$139$e4fe514c@dreader7.news.xs4all. nl...
> > I had exactly the same problem. Only I didnot know where to put them 6
> large
> > shims I got left.....
> > After I dropped the transfer case with those Shims, the problem was
gone.
> >
> > There is another solution to that problem, the Slip Yoke Eliminator Kit.
> It
> > helps to give you ground clearence, but it will cost you an arm and a
leg.
> >
> >
> > --
> > --
> > Greetings from the Netherlands,
> >
> > Bert
> >
> >
> > "William Oliveri" <wuji@bigvalley.net> schreef in bericht
> > news:c0f6ea$166d50$1@ID-193866.news.uni-berlin.de...
> > > First I put the lift kit (4" superlift kit) on the front end of my 83
> CJ7
> > > and drove it till the next weekend when I put the rear half on.
> > Everything
> > > was fine with only the front on. Now, with the rear on I get a
> vibration
> > > from the drive shaft it seems at around 40 and up. The when I let off
> the
> > > gas I hear a noise like a 10 speed bike would make when you are
coasting
> > > only heavier, click click click click.... etc.
> > >
> > > The kit came with a transfer case drop kit but I didn't install it.
> > Others
> > > I have talked to said they didn't use the transfer case drop kit.
> > >
> > > Has anyone else had this problem or can anyone give a comment or help?
> > >
> > > Thanks,
> > >
> > >
> >
> >
>
>
You need to drop the tcase with the shims, or get a double-cardan
driveshaft. If you already have a double cardan (CV) driveshaft, then you
have broken the ball thingie in the center. A double cardan has two Ujoints
at the tcase end, and in between these two ujoints is another part that is
basically a balljoint with a small but heavy spring inside. The spring acts
to keep the two ujoints lined up, but if the ball portion of this joint
breaks, then the ujoints can flop around relative to each other, and this
will set up the vibrations you are talking about.
One other thing you might need is to install those wedge-shaped shims
between the axle and the springs. This will tilt the pumpkin up a few
degrees and make the angles of the driveshaft a little flatter.
"William Oliveri" <wuji@bigvalley.net> wrote in message
news:c0g904$16tn5g$1@ID-193866.news.uni-berlin.de...
> Is not the SYE kit for a automatic tranny or not needed for a CJ7? Please
> correct me if I'm wrong.
>
>
>
>
> "Bert Boks" <tandartsbus@hotmail.com> wrote in message
> news:402b6090$0$139$e4fe514c@dreader7.news.xs4all. nl...
> > I had exactly the same problem. Only I didnot know where to put them 6
> large
> > shims I got left.....
> > After I dropped the transfer case with those Shims, the problem was
gone.
> >
> > There is another solution to that problem, the Slip Yoke Eliminator Kit.
> It
> > helps to give you ground clearence, but it will cost you an arm and a
leg.
> >
> >
> > --
> > --
> > Greetings from the Netherlands,
> >
> > Bert
> >
> >
> > "William Oliveri" <wuji@bigvalley.net> schreef in bericht
> > news:c0f6ea$166d50$1@ID-193866.news.uni-berlin.de...
> > > First I put the lift kit (4" superlift kit) on the front end of my 83
> CJ7
> > > and drove it till the next weekend when I put the rear half on.
> > Everything
> > > was fine with only the front on. Now, with the rear on I get a
> vibration
> > > from the drive shaft it seems at around 40 and up. The when I let off
> the
> > > gas I hear a noise like a 10 speed bike would make when you are
coasting
> > > only heavier, click click click click.... etc.
> > >
> > > The kit came with a transfer case drop kit but I didn't install it.
> > Others
> > > I have talked to said they didn't use the transfer case drop kit.
> > >
> > > Has anyone else had this problem or can anyone give a comment or help?
> > >
> > > Thanks,
> > >
> > >
> >
> >
>
>
#44
Guest
Posts: n/a
Re: Finished lift kit, now have drive shaft vibration
"ball thingie"? Highly technical term I suspect :-)
Anyway, the rear springs came with wedges attached (I couldn't figure out
why they were there, now I know).
I'll be installing the Transfer case drop spacers tonight along with the
transmission mount I just ordered. Hopefully this will do the trick.
Thanks,
"CRWLR" <beerman@yahoo.com> wrote in message
news:102ni2imliilec7@corp.supernews.com...
> The SYE is not needed with your D300 tcase.
>
> You need to drop the tcase with the shims, or get a double-cardan
> driveshaft. If you already have a double cardan (CV) driveshaft, then you
> have broken the ball thingie in the center. A double cardan has two
Ujoints
> at the tcase end, and in between these two ujoints is another part that is
> basically a balljoint with a small but heavy spring inside. The spring
acts
> to keep the two ujoints lined up, but if the ball portion of this joint
> breaks, then the ujoints can flop around relative to each other, and this
> will set up the vibrations you are talking about.
>
> One other thing you might need is to install those wedge-shaped shims
> between the axle and the springs. This will tilt the pumpkin up a few
> degrees and make the angles of the driveshaft a little flatter.
>
>
>
>
> "William Oliveri" <wuji@bigvalley.net> wrote in message
> news:c0g904$16tn5g$1@ID-193866.news.uni-berlin.de...
> > Is not the SYE kit for a automatic tranny or not needed for a CJ7?
Please
> > correct me if I'm wrong.
> >
> >
> >
> >
> > "Bert Boks" <tandartsbus@hotmail.com> wrote in message
> > news:402b6090$0$139$e4fe514c@dreader7.news.xs4all. nl...
> > > I had exactly the same problem. Only I didnot know where to put them 6
> > large
> > > shims I got left.....
> > > After I dropped the transfer case with those Shims, the problem was
> gone.
> > >
> > > There is another solution to that problem, the Slip Yoke Eliminator
Kit.
> > It
> > > helps to give you ground clearence, but it will cost you an arm and a
> leg.
> > >
> > >
> > > --
> > > --
> > > Greetings from the Netherlands,
> > >
> > > Bert
> > >
> > >
> > > "William Oliveri" <wuji@bigvalley.net> schreef in bericht
> > > news:c0f6ea$166d50$1@ID-193866.news.uni-berlin.de...
> > > > First I put the lift kit (4" superlift kit) on the front end of my
83
> > CJ7
> > > > and drove it till the next weekend when I put the rear half on.
> > > Everything
> > > > was fine with only the front on. Now, with the rear on I get a
> > vibration
> > > > from the drive shaft it seems at around 40 and up. The when I let
off
> > the
> > > > gas I hear a noise like a 10 speed bike would make when you are
> coasting
> > > > only heavier, click click click click.... etc.
> > > >
> > > > The kit came with a transfer case drop kit but I didn't install it.
> > > Others
> > > > I have talked to said they didn't use the transfer case drop kit.
> > > >
> > > > Has anyone else had this problem or can anyone give a comment or
help?
> > > >
> > > > Thanks,
> > > >
> > > >
> > >
> > >
> >
> >
>
Anyway, the rear springs came with wedges attached (I couldn't figure out
why they were there, now I know).
I'll be installing the Transfer case drop spacers tonight along with the
transmission mount I just ordered. Hopefully this will do the trick.
Thanks,
"CRWLR" <beerman@yahoo.com> wrote in message
news:102ni2imliilec7@corp.supernews.com...
> The SYE is not needed with your D300 tcase.
>
> You need to drop the tcase with the shims, or get a double-cardan
> driveshaft. If you already have a double cardan (CV) driveshaft, then you
> have broken the ball thingie in the center. A double cardan has two
Ujoints
> at the tcase end, and in between these two ujoints is another part that is
> basically a balljoint with a small but heavy spring inside. The spring
acts
> to keep the two ujoints lined up, but if the ball portion of this joint
> breaks, then the ujoints can flop around relative to each other, and this
> will set up the vibrations you are talking about.
>
> One other thing you might need is to install those wedge-shaped shims
> between the axle and the springs. This will tilt the pumpkin up a few
> degrees and make the angles of the driveshaft a little flatter.
>
>
>
>
> "William Oliveri" <wuji@bigvalley.net> wrote in message
> news:c0g904$16tn5g$1@ID-193866.news.uni-berlin.de...
> > Is not the SYE kit for a automatic tranny or not needed for a CJ7?
Please
> > correct me if I'm wrong.
> >
> >
> >
> >
> > "Bert Boks" <tandartsbus@hotmail.com> wrote in message
> > news:402b6090$0$139$e4fe514c@dreader7.news.xs4all. nl...
> > > I had exactly the same problem. Only I didnot know where to put them 6
> > large
> > > shims I got left.....
> > > After I dropped the transfer case with those Shims, the problem was
> gone.
> > >
> > > There is another solution to that problem, the Slip Yoke Eliminator
Kit.
> > It
> > > helps to give you ground clearence, but it will cost you an arm and a
> leg.
> > >
> > >
> > > --
> > > --
> > > Greetings from the Netherlands,
> > >
> > > Bert
> > >
> > >
> > > "William Oliveri" <wuji@bigvalley.net> schreef in bericht
> > > news:c0f6ea$166d50$1@ID-193866.news.uni-berlin.de...
> > > > First I put the lift kit (4" superlift kit) on the front end of my
83
> > CJ7
> > > > and drove it till the next weekend when I put the rear half on.
> > > Everything
> > > > was fine with only the front on. Now, with the rear on I get a
> > vibration
> > > > from the drive shaft it seems at around 40 and up. The when I let
off
> > the
> > > > gas I hear a noise like a 10 speed bike would make when you are
> coasting
> > > > only heavier, click click click click.... etc.
> > > >
> > > > The kit came with a transfer case drop kit but I didn't install it.
> > > Others
> > > > I have talked to said they didn't use the transfer case drop kit.
> > > >
> > > > Has anyone else had this problem or can anyone give a comment or
help?
> > > >
> > > > Thanks,
> > > >
> > > >
> > >
> > >
> >
> >
>
#45
Guest
Posts: n/a
Re: Finished lift kit, now have drive shaft vibration
"ball thingie"? Highly technical term I suspect :-)
Anyway, the rear springs came with wedges attached (I couldn't figure out
why they were there, now I know).
I'll be installing the Transfer case drop spacers tonight along with the
transmission mount I just ordered. Hopefully this will do the trick.
Thanks,
"CRWLR" <beerman@yahoo.com> wrote in message
news:102ni2imliilec7@corp.supernews.com...
> The SYE is not needed with your D300 tcase.
>
> You need to drop the tcase with the shims, or get a double-cardan
> driveshaft. If you already have a double cardan (CV) driveshaft, then you
> have broken the ball thingie in the center. A double cardan has two
Ujoints
> at the tcase end, and in between these two ujoints is another part that is
> basically a balljoint with a small but heavy spring inside. The spring
acts
> to keep the two ujoints lined up, but if the ball portion of this joint
> breaks, then the ujoints can flop around relative to each other, and this
> will set up the vibrations you are talking about.
>
> One other thing you might need is to install those wedge-shaped shims
> between the axle and the springs. This will tilt the pumpkin up a few
> degrees and make the angles of the driveshaft a little flatter.
>
>
>
>
> "William Oliveri" <wuji@bigvalley.net> wrote in message
> news:c0g904$16tn5g$1@ID-193866.news.uni-berlin.de...
> > Is not the SYE kit for a automatic tranny or not needed for a CJ7?
Please
> > correct me if I'm wrong.
> >
> >
> >
> >
> > "Bert Boks" <tandartsbus@hotmail.com> wrote in message
> > news:402b6090$0$139$e4fe514c@dreader7.news.xs4all. nl...
> > > I had exactly the same problem. Only I didnot know where to put them 6
> > large
> > > shims I got left.....
> > > After I dropped the transfer case with those Shims, the problem was
> gone.
> > >
> > > There is another solution to that problem, the Slip Yoke Eliminator
Kit.
> > It
> > > helps to give you ground clearence, but it will cost you an arm and a
> leg.
> > >
> > >
> > > --
> > > --
> > > Greetings from the Netherlands,
> > >
> > > Bert
> > >
> > >
> > > "William Oliveri" <wuji@bigvalley.net> schreef in bericht
> > > news:c0f6ea$166d50$1@ID-193866.news.uni-berlin.de...
> > > > First I put the lift kit (4" superlift kit) on the front end of my
83
> > CJ7
> > > > and drove it till the next weekend when I put the rear half on.
> > > Everything
> > > > was fine with only the front on. Now, with the rear on I get a
> > vibration
> > > > from the drive shaft it seems at around 40 and up. The when I let
off
> > the
> > > > gas I hear a noise like a 10 speed bike would make when you are
> coasting
> > > > only heavier, click click click click.... etc.
> > > >
> > > > The kit came with a transfer case drop kit but I didn't install it.
> > > Others
> > > > I have talked to said they didn't use the transfer case drop kit.
> > > >
> > > > Has anyone else had this problem or can anyone give a comment or
help?
> > > >
> > > > Thanks,
> > > >
> > > >
> > >
> > >
> >
> >
>
Anyway, the rear springs came with wedges attached (I couldn't figure out
why they were there, now I know).
I'll be installing the Transfer case drop spacers tonight along with the
transmission mount I just ordered. Hopefully this will do the trick.
Thanks,
"CRWLR" <beerman@yahoo.com> wrote in message
news:102ni2imliilec7@corp.supernews.com...
> The SYE is not needed with your D300 tcase.
>
> You need to drop the tcase with the shims, or get a double-cardan
> driveshaft. If you already have a double cardan (CV) driveshaft, then you
> have broken the ball thingie in the center. A double cardan has two
Ujoints
> at the tcase end, and in between these two ujoints is another part that is
> basically a balljoint with a small but heavy spring inside. The spring
acts
> to keep the two ujoints lined up, but if the ball portion of this joint
> breaks, then the ujoints can flop around relative to each other, and this
> will set up the vibrations you are talking about.
>
> One other thing you might need is to install those wedge-shaped shims
> between the axle and the springs. This will tilt the pumpkin up a few
> degrees and make the angles of the driveshaft a little flatter.
>
>
>
>
> "William Oliveri" <wuji@bigvalley.net> wrote in message
> news:c0g904$16tn5g$1@ID-193866.news.uni-berlin.de...
> > Is not the SYE kit for a automatic tranny or not needed for a CJ7?
Please
> > correct me if I'm wrong.
> >
> >
> >
> >
> > "Bert Boks" <tandartsbus@hotmail.com> wrote in message
> > news:402b6090$0$139$e4fe514c@dreader7.news.xs4all. nl...
> > > I had exactly the same problem. Only I didnot know where to put them 6
> > large
> > > shims I got left.....
> > > After I dropped the transfer case with those Shims, the problem was
> gone.
> > >
> > > There is another solution to that problem, the Slip Yoke Eliminator
Kit.
> > It
> > > helps to give you ground clearence, but it will cost you an arm and a
> leg.
> > >
> > >
> > > --
> > > --
> > > Greetings from the Netherlands,
> > >
> > > Bert
> > >
> > >
> > > "William Oliveri" <wuji@bigvalley.net> schreef in bericht
> > > news:c0f6ea$166d50$1@ID-193866.news.uni-berlin.de...
> > > > First I put the lift kit (4" superlift kit) on the front end of my
83
> > CJ7
> > > > and drove it till the next weekend when I put the rear half on.
> > > Everything
> > > > was fine with only the front on. Now, with the rear on I get a
> > vibration
> > > > from the drive shaft it seems at around 40 and up. The when I let
off
> > the
> > > > gas I hear a noise like a 10 speed bike would make when you are
> coasting
> > > > only heavier, click click click click.... etc.
> > > >
> > > > The kit came with a transfer case drop kit but I didn't install it.
> > > Others
> > > > I have talked to said they didn't use the transfer case drop kit.
> > > >
> > > > Has anyone else had this problem or can anyone give a comment or
help?
> > > >
> > > > Thanks,
> > > >
> > > >
> > >
> > >
> >
> >
>
#46
Guest
Posts: n/a
Re: Finished lift kit, now have drive shaft vibration
"ball thingie"? Highly technical term I suspect :-)
Anyway, the rear springs came with wedges attached (I couldn't figure out
why they were there, now I know).
I'll be installing the Transfer case drop spacers tonight along with the
transmission mount I just ordered. Hopefully this will do the trick.
Thanks,
"CRWLR" <beerman@yahoo.com> wrote in message
news:102ni2imliilec7@corp.supernews.com...
> The SYE is not needed with your D300 tcase.
>
> You need to drop the tcase with the shims, or get a double-cardan
> driveshaft. If you already have a double cardan (CV) driveshaft, then you
> have broken the ball thingie in the center. A double cardan has two
Ujoints
> at the tcase end, and in between these two ujoints is another part that is
> basically a balljoint with a small but heavy spring inside. The spring
acts
> to keep the two ujoints lined up, but if the ball portion of this joint
> breaks, then the ujoints can flop around relative to each other, and this
> will set up the vibrations you are talking about.
>
> One other thing you might need is to install those wedge-shaped shims
> between the axle and the springs. This will tilt the pumpkin up a few
> degrees and make the angles of the driveshaft a little flatter.
>
>
>
>
> "William Oliveri" <wuji@bigvalley.net> wrote in message
> news:c0g904$16tn5g$1@ID-193866.news.uni-berlin.de...
> > Is not the SYE kit for a automatic tranny or not needed for a CJ7?
Please
> > correct me if I'm wrong.
> >
> >
> >
> >
> > "Bert Boks" <tandartsbus@hotmail.com> wrote in message
> > news:402b6090$0$139$e4fe514c@dreader7.news.xs4all. nl...
> > > I had exactly the same problem. Only I didnot know where to put them 6
> > large
> > > shims I got left.....
> > > After I dropped the transfer case with those Shims, the problem was
> gone.
> > >
> > > There is another solution to that problem, the Slip Yoke Eliminator
Kit.
> > It
> > > helps to give you ground clearence, but it will cost you an arm and a
> leg.
> > >
> > >
> > > --
> > > --
> > > Greetings from the Netherlands,
> > >
> > > Bert
> > >
> > >
> > > "William Oliveri" <wuji@bigvalley.net> schreef in bericht
> > > news:c0f6ea$166d50$1@ID-193866.news.uni-berlin.de...
> > > > First I put the lift kit (4" superlift kit) on the front end of my
83
> > CJ7
> > > > and drove it till the next weekend when I put the rear half on.
> > > Everything
> > > > was fine with only the front on. Now, with the rear on I get a
> > vibration
> > > > from the drive shaft it seems at around 40 and up. The when I let
off
> > the
> > > > gas I hear a noise like a 10 speed bike would make when you are
> coasting
> > > > only heavier, click click click click.... etc.
> > > >
> > > > The kit came with a transfer case drop kit but I didn't install it.
> > > Others
> > > > I have talked to said they didn't use the transfer case drop kit.
> > > >
> > > > Has anyone else had this problem or can anyone give a comment or
help?
> > > >
> > > > Thanks,
> > > >
> > > >
> > >
> > >
> >
> >
>
Anyway, the rear springs came with wedges attached (I couldn't figure out
why they were there, now I know).
I'll be installing the Transfer case drop spacers tonight along with the
transmission mount I just ordered. Hopefully this will do the trick.
Thanks,
"CRWLR" <beerman@yahoo.com> wrote in message
news:102ni2imliilec7@corp.supernews.com...
> The SYE is not needed with your D300 tcase.
>
> You need to drop the tcase with the shims, or get a double-cardan
> driveshaft. If you already have a double cardan (CV) driveshaft, then you
> have broken the ball thingie in the center. A double cardan has two
Ujoints
> at the tcase end, and in between these two ujoints is another part that is
> basically a balljoint with a small but heavy spring inside. The spring
acts
> to keep the two ujoints lined up, but if the ball portion of this joint
> breaks, then the ujoints can flop around relative to each other, and this
> will set up the vibrations you are talking about.
>
> One other thing you might need is to install those wedge-shaped shims
> between the axle and the springs. This will tilt the pumpkin up a few
> degrees and make the angles of the driveshaft a little flatter.
>
>
>
>
> "William Oliveri" <wuji@bigvalley.net> wrote in message
> news:c0g904$16tn5g$1@ID-193866.news.uni-berlin.de...
> > Is not the SYE kit for a automatic tranny or not needed for a CJ7?
Please
> > correct me if I'm wrong.
> >
> >
> >
> >
> > "Bert Boks" <tandartsbus@hotmail.com> wrote in message
> > news:402b6090$0$139$e4fe514c@dreader7.news.xs4all. nl...
> > > I had exactly the same problem. Only I didnot know where to put them 6
> > large
> > > shims I got left.....
> > > After I dropped the transfer case with those Shims, the problem was
> gone.
> > >
> > > There is another solution to that problem, the Slip Yoke Eliminator
Kit.
> > It
> > > helps to give you ground clearence, but it will cost you an arm and a
> leg.
> > >
> > >
> > > --
> > > --
> > > Greetings from the Netherlands,
> > >
> > > Bert
> > >
> > >
> > > "William Oliveri" <wuji@bigvalley.net> schreef in bericht
> > > news:c0f6ea$166d50$1@ID-193866.news.uni-berlin.de...
> > > > First I put the lift kit (4" superlift kit) on the front end of my
83
> > CJ7
> > > > and drove it till the next weekend when I put the rear half on.
> > > Everything
> > > > was fine with only the front on. Now, with the rear on I get a
> > vibration
> > > > from the drive shaft it seems at around 40 and up. The when I let
off
> > the
> > > > gas I hear a noise like a 10 speed bike would make when you are
> coasting
> > > > only heavier, click click click click.... etc.
> > > >
> > > > The kit came with a transfer case drop kit but I didn't install it.
> > > Others
> > > > I have talked to said they didn't use the transfer case drop kit.
> > > >
> > > > Has anyone else had this problem or can anyone give a comment or
help?
> > > >
> > > > Thanks,
> > > >
> > > >
> > >
> > >
> >
> >
>
#47
Guest
Posts: n/a
Re: Finished lift kit, now have drive shaft vibration
No it is a UCL (Universal Carpart Locator) terminology like that is used
a lot in carparts stores around the country.
William Oliveri wrote:
> "ball thingie"? Highly technical term I suspect :-)
>
> Anyway, the rear springs came with wedges attached (I couldn't figure out
> why they were there, now I know).
>
> I'll be installing the Transfer case drop spacers tonight along with the
> transmission mount I just ordered. Hopefully this will do the trick.
>
> Thanks,
>
>
> "CRWLR" <beerman@yahoo.com> wrote in message
> news:102ni2imliilec7@corp.supernews.com...
>
>>The SYE is not needed with your D300 tcase.
>>
>>You need to drop the tcase with the shims, or get a double-cardan
>>driveshaft. If you already have a double cardan (CV) driveshaft, then you
>>have broken the ball thingie in the center. A double cardan has two
>
> Ujoints
>
>>at the tcase end, and in between these two ujoints is another part that is
>>basically a balljoint with a small but heavy spring inside. The spring
>
> acts
>
>>to keep the two ujoints lined up, but if the ball portion of this joint
>>breaks, then the ujoints can flop around relative to each other, and this
>>will set up the vibrations you are talking about.
>>
>>One other thing you might need is to install those wedge-shaped shims
>>between the axle and the springs. This will tilt the pumpkin up a few
>>degrees and make the angles of the driveshaft a little flatter.
>>
>>
>>
>>
>>"William Oliveri" <wuji@bigvalley.net> wrote in message
>>news:c0g904$16tn5g$1@ID-193866.news.uni-berlin.de...
>>
>>>Is not the SYE kit for a automatic tranny or not needed for a CJ7?
>
> Please
>
>>>correct me if I'm wrong.
>>>
>>>
>>>
>>>
>>>"Bert Boks" <tandartsbus@hotmail.com> wrote in message
>>>news:402b6090$0$139$e4fe514c@dreader7.news.xs4a ll.nl...
>>>
>>>>I had exactly the same problem. Only I didnot know where to put them 6
>>>
>>>large
>>>
>>>>shims I got left.....
>>>>After I dropped the transfer case with those Shims, the problem was
>>
>>gone.
>>
>>>>There is another solution to that problem, the Slip Yoke Eliminator
>
> Kit.
>
>>>It
>>>
>>>>helps to give you ground clearence, but it will cost you an arm and a
>>
>>leg.
>>
>>>>
>>>>--
>>>>--
>>>>Greetings from the Netherlands,
>>>>
>>>>Bert
>>>>
>>>>
>>>>"William Oliveri" <wuji@bigvalley.net> schreef in bericht
>>>>news:c0f6ea$166d50$1@ID-193866.news.uni-berlin.de...
>>>>
>>>>>First I put the lift kit (4" superlift kit) on the front end of my
>
> 83
>
>>>CJ7
>>>
>>>>>and drove it till the next weekend when I put the rear half on.
>>>>
>>>>Everything
>>>>
>>>>>was fine with only the front on. Now, with the rear on I get a
>>>
>>>vibration
>>>
>>>>>from the drive shaft it seems at around 40 and up. The when I let
>
> off
>
>>>the
>>>
>>>>>gas I hear a noise like a 10 speed bike would make when you are
>>
>>coasting
>>
>>>>>only heavier, click click click click.... etc.
>>>>>
>>>>>The kit came with a transfer case drop kit but I didn't install it.
>>>>
>>>>Others
>>>>
>>>>>I have talked to said they didn't use the transfer case drop kit.
>>>>>
>>>>>Has anyone else had this problem or can anyone give a comment or
>
> help?
>
>>>>>Thanks,
>>>>>
>>>>>
>>>>
>>>>
>>>
>
>
a lot in carparts stores around the country.
William Oliveri wrote:
> "ball thingie"? Highly technical term I suspect :-)
>
> Anyway, the rear springs came with wedges attached (I couldn't figure out
> why they were there, now I know).
>
> I'll be installing the Transfer case drop spacers tonight along with the
> transmission mount I just ordered. Hopefully this will do the trick.
>
> Thanks,
>
>
> "CRWLR" <beerman@yahoo.com> wrote in message
> news:102ni2imliilec7@corp.supernews.com...
>
>>The SYE is not needed with your D300 tcase.
>>
>>You need to drop the tcase with the shims, or get a double-cardan
>>driveshaft. If you already have a double cardan (CV) driveshaft, then you
>>have broken the ball thingie in the center. A double cardan has two
>
> Ujoints
>
>>at the tcase end, and in between these two ujoints is another part that is
>>basically a balljoint with a small but heavy spring inside. The spring
>
> acts
>
>>to keep the two ujoints lined up, but if the ball portion of this joint
>>breaks, then the ujoints can flop around relative to each other, and this
>>will set up the vibrations you are talking about.
>>
>>One other thing you might need is to install those wedge-shaped shims
>>between the axle and the springs. This will tilt the pumpkin up a few
>>degrees and make the angles of the driveshaft a little flatter.
>>
>>
>>
>>
>>"William Oliveri" <wuji@bigvalley.net> wrote in message
>>news:c0g904$16tn5g$1@ID-193866.news.uni-berlin.de...
>>
>>>Is not the SYE kit for a automatic tranny or not needed for a CJ7?
>
> Please
>
>>>correct me if I'm wrong.
>>>
>>>
>>>
>>>
>>>"Bert Boks" <tandartsbus@hotmail.com> wrote in message
>>>news:402b6090$0$139$e4fe514c@dreader7.news.xs4a ll.nl...
>>>
>>>>I had exactly the same problem. Only I didnot know where to put them 6
>>>
>>>large
>>>
>>>>shims I got left.....
>>>>After I dropped the transfer case with those Shims, the problem was
>>
>>gone.
>>
>>>>There is another solution to that problem, the Slip Yoke Eliminator
>
> Kit.
>
>>>It
>>>
>>>>helps to give you ground clearence, but it will cost you an arm and a
>>
>>leg.
>>
>>>>
>>>>--
>>>>--
>>>>Greetings from the Netherlands,
>>>>
>>>>Bert
>>>>
>>>>
>>>>"William Oliveri" <wuji@bigvalley.net> schreef in bericht
>>>>news:c0f6ea$166d50$1@ID-193866.news.uni-berlin.de...
>>>>
>>>>>First I put the lift kit (4" superlift kit) on the front end of my
>
> 83
>
>>>CJ7
>>>
>>>>>and drove it till the next weekend when I put the rear half on.
>>>>
>>>>Everything
>>>>
>>>>>was fine with only the front on. Now, with the rear on I get a
>>>
>>>vibration
>>>
>>>>>from the drive shaft it seems at around 40 and up. The when I let
>
> off
>
>>>the
>>>
>>>>>gas I hear a noise like a 10 speed bike would make when you are
>>
>>coasting
>>
>>>>>only heavier, click click click click.... etc.
>>>>>
>>>>>The kit came with a transfer case drop kit but I didn't install it.
>>>>
>>>>Others
>>>>
>>>>>I have talked to said they didn't use the transfer case drop kit.
>>>>>
>>>>>Has anyone else had this problem or can anyone give a comment or
>
> help?
>
>>>>>Thanks,
>>>>>
>>>>>
>>>>
>>>>
>>>
>
>
#48
Guest
Posts: n/a
Re: Finished lift kit, now have drive shaft vibration
No it is a UCL (Universal Carpart Locator) terminology like that is used
a lot in carparts stores around the country.
William Oliveri wrote:
> "ball thingie"? Highly technical term I suspect :-)
>
> Anyway, the rear springs came with wedges attached (I couldn't figure out
> why they were there, now I know).
>
> I'll be installing the Transfer case drop spacers tonight along with the
> transmission mount I just ordered. Hopefully this will do the trick.
>
> Thanks,
>
>
> "CRWLR" <beerman@yahoo.com> wrote in message
> news:102ni2imliilec7@corp.supernews.com...
>
>>The SYE is not needed with your D300 tcase.
>>
>>You need to drop the tcase with the shims, or get a double-cardan
>>driveshaft. If you already have a double cardan (CV) driveshaft, then you
>>have broken the ball thingie in the center. A double cardan has two
>
> Ujoints
>
>>at the tcase end, and in between these two ujoints is another part that is
>>basically a balljoint with a small but heavy spring inside. The spring
>
> acts
>
>>to keep the two ujoints lined up, but if the ball portion of this joint
>>breaks, then the ujoints can flop around relative to each other, and this
>>will set up the vibrations you are talking about.
>>
>>One other thing you might need is to install those wedge-shaped shims
>>between the axle and the springs. This will tilt the pumpkin up a few
>>degrees and make the angles of the driveshaft a little flatter.
>>
>>
>>
>>
>>"William Oliveri" <wuji@bigvalley.net> wrote in message
>>news:c0g904$16tn5g$1@ID-193866.news.uni-berlin.de...
>>
>>>Is not the SYE kit for a automatic tranny or not needed for a CJ7?
>
> Please
>
>>>correct me if I'm wrong.
>>>
>>>
>>>
>>>
>>>"Bert Boks" <tandartsbus@hotmail.com> wrote in message
>>>news:402b6090$0$139$e4fe514c@dreader7.news.xs4a ll.nl...
>>>
>>>>I had exactly the same problem. Only I didnot know where to put them 6
>>>
>>>large
>>>
>>>>shims I got left.....
>>>>After I dropped the transfer case with those Shims, the problem was
>>
>>gone.
>>
>>>>There is another solution to that problem, the Slip Yoke Eliminator
>
> Kit.
>
>>>It
>>>
>>>>helps to give you ground clearence, but it will cost you an arm and a
>>
>>leg.
>>
>>>>
>>>>--
>>>>--
>>>>Greetings from the Netherlands,
>>>>
>>>>Bert
>>>>
>>>>
>>>>"William Oliveri" <wuji@bigvalley.net> schreef in bericht
>>>>news:c0f6ea$166d50$1@ID-193866.news.uni-berlin.de...
>>>>
>>>>>First I put the lift kit (4" superlift kit) on the front end of my
>
> 83
>
>>>CJ7
>>>
>>>>>and drove it till the next weekend when I put the rear half on.
>>>>
>>>>Everything
>>>>
>>>>>was fine with only the front on. Now, with the rear on I get a
>>>
>>>vibration
>>>
>>>>>from the drive shaft it seems at around 40 and up. The when I let
>
> off
>
>>>the
>>>
>>>>>gas I hear a noise like a 10 speed bike would make when you are
>>
>>coasting
>>
>>>>>only heavier, click click click click.... etc.
>>>>>
>>>>>The kit came with a transfer case drop kit but I didn't install it.
>>>>
>>>>Others
>>>>
>>>>>I have talked to said they didn't use the transfer case drop kit.
>>>>>
>>>>>Has anyone else had this problem or can anyone give a comment or
>
> help?
>
>>>>>Thanks,
>>>>>
>>>>>
>>>>
>>>>
>>>
>
>
a lot in carparts stores around the country.
William Oliveri wrote:
> "ball thingie"? Highly technical term I suspect :-)
>
> Anyway, the rear springs came with wedges attached (I couldn't figure out
> why they were there, now I know).
>
> I'll be installing the Transfer case drop spacers tonight along with the
> transmission mount I just ordered. Hopefully this will do the trick.
>
> Thanks,
>
>
> "CRWLR" <beerman@yahoo.com> wrote in message
> news:102ni2imliilec7@corp.supernews.com...
>
>>The SYE is not needed with your D300 tcase.
>>
>>You need to drop the tcase with the shims, or get a double-cardan
>>driveshaft. If you already have a double cardan (CV) driveshaft, then you
>>have broken the ball thingie in the center. A double cardan has two
>
> Ujoints
>
>>at the tcase end, and in between these two ujoints is another part that is
>>basically a balljoint with a small but heavy spring inside. The spring
>
> acts
>
>>to keep the two ujoints lined up, but if the ball portion of this joint
>>breaks, then the ujoints can flop around relative to each other, and this
>>will set up the vibrations you are talking about.
>>
>>One other thing you might need is to install those wedge-shaped shims
>>between the axle and the springs. This will tilt the pumpkin up a few
>>degrees and make the angles of the driveshaft a little flatter.
>>
>>
>>
>>
>>"William Oliveri" <wuji@bigvalley.net> wrote in message
>>news:c0g904$16tn5g$1@ID-193866.news.uni-berlin.de...
>>
>>>Is not the SYE kit for a automatic tranny or not needed for a CJ7?
>
> Please
>
>>>correct me if I'm wrong.
>>>
>>>
>>>
>>>
>>>"Bert Boks" <tandartsbus@hotmail.com> wrote in message
>>>news:402b6090$0$139$e4fe514c@dreader7.news.xs4a ll.nl...
>>>
>>>>I had exactly the same problem. Only I didnot know where to put them 6
>>>
>>>large
>>>
>>>>shims I got left.....
>>>>After I dropped the transfer case with those Shims, the problem was
>>
>>gone.
>>
>>>>There is another solution to that problem, the Slip Yoke Eliminator
>
> Kit.
>
>>>It
>>>
>>>>helps to give you ground clearence, but it will cost you an arm and a
>>
>>leg.
>>
>>>>
>>>>--
>>>>--
>>>>Greetings from the Netherlands,
>>>>
>>>>Bert
>>>>
>>>>
>>>>"William Oliveri" <wuji@bigvalley.net> schreef in bericht
>>>>news:c0f6ea$166d50$1@ID-193866.news.uni-berlin.de...
>>>>
>>>>>First I put the lift kit (4" superlift kit) on the front end of my
>
> 83
>
>>>CJ7
>>>
>>>>>and drove it till the next weekend when I put the rear half on.
>>>>
>>>>Everything
>>>>
>>>>>was fine with only the front on. Now, with the rear on I get a
>>>
>>>vibration
>>>
>>>>>from the drive shaft it seems at around 40 and up. The when I let
>
> off
>
>>>the
>>>
>>>>>gas I hear a noise like a 10 speed bike would make when you are
>>
>>coasting
>>
>>>>>only heavier, click click click click.... etc.
>>>>>
>>>>>The kit came with a transfer case drop kit but I didn't install it.
>>>>
>>>>Others
>>>>
>>>>>I have talked to said they didn't use the transfer case drop kit.
>>>>>
>>>>>Has anyone else had this problem or can anyone give a comment or
>
> help?
>
>>>>>Thanks,
>>>>>
>>>>>
>>>>
>>>>
>>>
>
>
#49
Guest
Posts: n/a
Re: Finished lift kit, now have drive shaft vibration
No it is a UCL (Universal Carpart Locator) terminology like that is used
a lot in carparts stores around the country.
William Oliveri wrote:
> "ball thingie"? Highly technical term I suspect :-)
>
> Anyway, the rear springs came with wedges attached (I couldn't figure out
> why they were there, now I know).
>
> I'll be installing the Transfer case drop spacers tonight along with the
> transmission mount I just ordered. Hopefully this will do the trick.
>
> Thanks,
>
>
> "CRWLR" <beerman@yahoo.com> wrote in message
> news:102ni2imliilec7@corp.supernews.com...
>
>>The SYE is not needed with your D300 tcase.
>>
>>You need to drop the tcase with the shims, or get a double-cardan
>>driveshaft. If you already have a double cardan (CV) driveshaft, then you
>>have broken the ball thingie in the center. A double cardan has two
>
> Ujoints
>
>>at the tcase end, and in between these two ujoints is another part that is
>>basically a balljoint with a small but heavy spring inside. The spring
>
> acts
>
>>to keep the two ujoints lined up, but if the ball portion of this joint
>>breaks, then the ujoints can flop around relative to each other, and this
>>will set up the vibrations you are talking about.
>>
>>One other thing you might need is to install those wedge-shaped shims
>>between the axle and the springs. This will tilt the pumpkin up a few
>>degrees and make the angles of the driveshaft a little flatter.
>>
>>
>>
>>
>>"William Oliveri" <wuji@bigvalley.net> wrote in message
>>news:c0g904$16tn5g$1@ID-193866.news.uni-berlin.de...
>>
>>>Is not the SYE kit for a automatic tranny or not needed for a CJ7?
>
> Please
>
>>>correct me if I'm wrong.
>>>
>>>
>>>
>>>
>>>"Bert Boks" <tandartsbus@hotmail.com> wrote in message
>>>news:402b6090$0$139$e4fe514c@dreader7.news.xs4a ll.nl...
>>>
>>>>I had exactly the same problem. Only I didnot know where to put them 6
>>>
>>>large
>>>
>>>>shims I got left.....
>>>>After I dropped the transfer case with those Shims, the problem was
>>
>>gone.
>>
>>>>There is another solution to that problem, the Slip Yoke Eliminator
>
> Kit.
>
>>>It
>>>
>>>>helps to give you ground clearence, but it will cost you an arm and a
>>
>>leg.
>>
>>>>
>>>>--
>>>>--
>>>>Greetings from the Netherlands,
>>>>
>>>>Bert
>>>>
>>>>
>>>>"William Oliveri" <wuji@bigvalley.net> schreef in bericht
>>>>news:c0f6ea$166d50$1@ID-193866.news.uni-berlin.de...
>>>>
>>>>>First I put the lift kit (4" superlift kit) on the front end of my
>
> 83
>
>>>CJ7
>>>
>>>>>and drove it till the next weekend when I put the rear half on.
>>>>
>>>>Everything
>>>>
>>>>>was fine with only the front on. Now, with the rear on I get a
>>>
>>>vibration
>>>
>>>>>from the drive shaft it seems at around 40 and up. The when I let
>
> off
>
>>>the
>>>
>>>>>gas I hear a noise like a 10 speed bike would make when you are
>>
>>coasting
>>
>>>>>only heavier, click click click click.... etc.
>>>>>
>>>>>The kit came with a transfer case drop kit but I didn't install it.
>>>>
>>>>Others
>>>>
>>>>>I have talked to said they didn't use the transfer case drop kit.
>>>>>
>>>>>Has anyone else had this problem or can anyone give a comment or
>
> help?
>
>>>>>Thanks,
>>>>>
>>>>>
>>>>
>>>>
>>>
>
>
a lot in carparts stores around the country.
William Oliveri wrote:
> "ball thingie"? Highly technical term I suspect :-)
>
> Anyway, the rear springs came with wedges attached (I couldn't figure out
> why they were there, now I know).
>
> I'll be installing the Transfer case drop spacers tonight along with the
> transmission mount I just ordered. Hopefully this will do the trick.
>
> Thanks,
>
>
> "CRWLR" <beerman@yahoo.com> wrote in message
> news:102ni2imliilec7@corp.supernews.com...
>
>>The SYE is not needed with your D300 tcase.
>>
>>You need to drop the tcase with the shims, or get a double-cardan
>>driveshaft. If you already have a double cardan (CV) driveshaft, then you
>>have broken the ball thingie in the center. A double cardan has two
>
> Ujoints
>
>>at the tcase end, and in between these two ujoints is another part that is
>>basically a balljoint with a small but heavy spring inside. The spring
>
> acts
>
>>to keep the two ujoints lined up, but if the ball portion of this joint
>>breaks, then the ujoints can flop around relative to each other, and this
>>will set up the vibrations you are talking about.
>>
>>One other thing you might need is to install those wedge-shaped shims
>>between the axle and the springs. This will tilt the pumpkin up a few
>>degrees and make the angles of the driveshaft a little flatter.
>>
>>
>>
>>
>>"William Oliveri" <wuji@bigvalley.net> wrote in message
>>news:c0g904$16tn5g$1@ID-193866.news.uni-berlin.de...
>>
>>>Is not the SYE kit for a automatic tranny or not needed for a CJ7?
>
> Please
>
>>>correct me if I'm wrong.
>>>
>>>
>>>
>>>
>>>"Bert Boks" <tandartsbus@hotmail.com> wrote in message
>>>news:402b6090$0$139$e4fe514c@dreader7.news.xs4a ll.nl...
>>>
>>>>I had exactly the same problem. Only I didnot know where to put them 6
>>>
>>>large
>>>
>>>>shims I got left.....
>>>>After I dropped the transfer case with those Shims, the problem was
>>
>>gone.
>>
>>>>There is another solution to that problem, the Slip Yoke Eliminator
>
> Kit.
>
>>>It
>>>
>>>>helps to give you ground clearence, but it will cost you an arm and a
>>
>>leg.
>>
>>>>
>>>>--
>>>>--
>>>>Greetings from the Netherlands,
>>>>
>>>>Bert
>>>>
>>>>
>>>>"William Oliveri" <wuji@bigvalley.net> schreef in bericht
>>>>news:c0f6ea$166d50$1@ID-193866.news.uni-berlin.de...
>>>>
>>>>>First I put the lift kit (4" superlift kit) on the front end of my
>
> 83
>
>>>CJ7
>>>
>>>>>and drove it till the next weekend when I put the rear half on.
>>>>
>>>>Everything
>>>>
>>>>>was fine with only the front on. Now, with the rear on I get a
>>>
>>>vibration
>>>
>>>>>from the drive shaft it seems at around 40 and up. The when I let
>
> off
>
>>>the
>>>
>>>>>gas I hear a noise like a 10 speed bike would make when you are
>>
>>coasting
>>
>>>>>only heavier, click click click click.... etc.
>>>>>
>>>>>The kit came with a transfer case drop kit but I didn't install it.
>>>>
>>>>Others
>>>>
>>>>>I have talked to said they didn't use the transfer case drop kit.
>>>>>
>>>>>Has anyone else had this problem or can anyone give a comment or
>
> help?
>
>>>>>Thanks,
>>>>>
>>>>>
>>>>
>>>>
>>>
>
>
#50
Guest
Posts: n/a
Re: Finished lift kit, now have drive shaft vibration
I heard one the other day, "buttock-dyno "
"Ron Croonenberg" <ronc@depauw.edu> wrote in message
news:c0gilu$baj$2@terra.csc.depauw.edu...
> No it is a UCL (Universal Carpart Locator) terminology like that is used
> a lot in carparts stores around the country.
>
>
>
> William Oliveri wrote:
>
> > "ball thingie"? Highly technical term I suspect :-)
> >
> > Anyway, the rear springs came with wedges attached (I couldn't figure
out
> > why they were there, now I know).
> >
> > I'll be installing the Transfer case drop spacers tonight along with the
> > transmission mount I just ordered. Hopefully this will do the trick.
> >
> > Thanks,
> >
> >
> > "CRWLR" <beerman@yahoo.com> wrote in message
> > news:102ni2imliilec7@corp.supernews.com...
> >
> >>The SYE is not needed with your D300 tcase.
> >>
> >>You need to drop the tcase with the shims, or get a double-cardan
> >>driveshaft. If you already have a double cardan (CV) driveshaft, then
you
> >>have broken the ball thingie in the center. A double cardan has two
> >
> > Ujoints
> >
> >>at the tcase end, and in between these two ujoints is another part that
is
> >>basically a balljoint with a small but heavy spring inside. The spring
> >
> > acts
> >
> >>to keep the two ujoints lined up, but if the ball portion of this joint
> >>breaks, then the ujoints can flop around relative to each other, and
this
> >>will set up the vibrations you are talking about.
> >>
> >>One other thing you might need is to install those wedge-shaped shims
> >>between the axle and the springs. This will tilt the pumpkin up a few
> >>degrees and make the angles of the driveshaft a little flatter.
> >>
> >>
> >>
> >>
> >>"William Oliveri" <wuji@bigvalley.net> wrote in message
> >>news:c0g904$16tn5g$1@ID-193866.news.uni-berlin.de...
> >>
> >>>Is not the SYE kit for a automatic tranny or not needed for a CJ7?
> >
> > Please
> >
> >>>correct me if I'm wrong.
> >>>
> >>>
> >>>
> >>>
> >>>"Bert Boks" <tandartsbus@hotmail.com> wrote in message
> >>>news:402b6090$0$139$e4fe514c@dreader7.news.xs4a ll.nl...
> >>>
> >>>>I had exactly the same problem. Only I didnot know where to put them 6
> >>>
> >>>large
> >>>
> >>>>shims I got left.....
> >>>>After I dropped the transfer case with those Shims, the problem was
> >>
> >>gone.
> >>
> >>>>There is another solution to that problem, the Slip Yoke Eliminator
> >
> > Kit.
> >
> >>>It
> >>>
> >>>>helps to give you ground clearence, but it will cost you an arm and a
> >>
> >>leg.
> >>
> >>>>
> >>>>--
> >>>>--
> >>>>Greetings from the Netherlands,
> >>>>
> >>>>Bert
> >>>>
> >>>>
> >>>>"William Oliveri" <wuji@bigvalley.net> schreef in bericht
> >>>>news:c0f6ea$166d50$1@ID-193866.news.uni-berlin.de...
> >>>>
> >>>>>First I put the lift kit (4" superlift kit) on the front end of my
> >
> > 83
> >
> >>>CJ7
> >>>
> >>>>>and drove it till the next weekend when I put the rear half on.
> >>>>
> >>>>Everything
> >>>>
> >>>>>was fine with only the front on. Now, with the rear on I get a
> >>>
> >>>vibration
> >>>
> >>>>>from the drive shaft it seems at around 40 and up. The when I let
> >
> > off
> >
> >>>the
> >>>
> >>>>>gas I hear a noise like a 10 speed bike would make when you are
> >>
> >>coasting
> >>
> >>>>>only heavier, click click click click.... etc.
> >>>>>
> >>>>>The kit came with a transfer case drop kit but I didn't install it.
> >>>>
> >>>>Others
> >>>>
> >>>>>I have talked to said they didn't use the transfer case drop kit.
> >>>>>
> >>>>>Has anyone else had this problem or can anyone give a comment or
> >
> > help?
> >
> >>>>>Thanks,
> >>>>>
> >>>>>
> >>>>
> >>>>
> >>>
> >
> >
>
"Ron Croonenberg" <ronc@depauw.edu> wrote in message
news:c0gilu$baj$2@terra.csc.depauw.edu...
> No it is a UCL (Universal Carpart Locator) terminology like that is used
> a lot in carparts stores around the country.
>
>
>
> William Oliveri wrote:
>
> > "ball thingie"? Highly technical term I suspect :-)
> >
> > Anyway, the rear springs came with wedges attached (I couldn't figure
out
> > why they were there, now I know).
> >
> > I'll be installing the Transfer case drop spacers tonight along with the
> > transmission mount I just ordered. Hopefully this will do the trick.
> >
> > Thanks,
> >
> >
> > "CRWLR" <beerman@yahoo.com> wrote in message
> > news:102ni2imliilec7@corp.supernews.com...
> >
> >>The SYE is not needed with your D300 tcase.
> >>
> >>You need to drop the tcase with the shims, or get a double-cardan
> >>driveshaft. If you already have a double cardan (CV) driveshaft, then
you
> >>have broken the ball thingie in the center. A double cardan has two
> >
> > Ujoints
> >
> >>at the tcase end, and in between these two ujoints is another part that
is
> >>basically a balljoint with a small but heavy spring inside. The spring
> >
> > acts
> >
> >>to keep the two ujoints lined up, but if the ball portion of this joint
> >>breaks, then the ujoints can flop around relative to each other, and
this
> >>will set up the vibrations you are talking about.
> >>
> >>One other thing you might need is to install those wedge-shaped shims
> >>between the axle and the springs. This will tilt the pumpkin up a few
> >>degrees and make the angles of the driveshaft a little flatter.
> >>
> >>
> >>
> >>
> >>"William Oliveri" <wuji@bigvalley.net> wrote in message
> >>news:c0g904$16tn5g$1@ID-193866.news.uni-berlin.de...
> >>
> >>>Is not the SYE kit for a automatic tranny or not needed for a CJ7?
> >
> > Please
> >
> >>>correct me if I'm wrong.
> >>>
> >>>
> >>>
> >>>
> >>>"Bert Boks" <tandartsbus@hotmail.com> wrote in message
> >>>news:402b6090$0$139$e4fe514c@dreader7.news.xs4a ll.nl...
> >>>
> >>>>I had exactly the same problem. Only I didnot know where to put them 6
> >>>
> >>>large
> >>>
> >>>>shims I got left.....
> >>>>After I dropped the transfer case with those Shims, the problem was
> >>
> >>gone.
> >>
> >>>>There is another solution to that problem, the Slip Yoke Eliminator
> >
> > Kit.
> >
> >>>It
> >>>
> >>>>helps to give you ground clearence, but it will cost you an arm and a
> >>
> >>leg.
> >>
> >>>>
> >>>>--
> >>>>--
> >>>>Greetings from the Netherlands,
> >>>>
> >>>>Bert
> >>>>
> >>>>
> >>>>"William Oliveri" <wuji@bigvalley.net> schreef in bericht
> >>>>news:c0f6ea$166d50$1@ID-193866.news.uni-berlin.de...
> >>>>
> >>>>>First I put the lift kit (4" superlift kit) on the front end of my
> >
> > 83
> >
> >>>CJ7
> >>>
> >>>>>and drove it till the next weekend when I put the rear half on.
> >>>>
> >>>>Everything
> >>>>
> >>>>>was fine with only the front on. Now, with the rear on I get a
> >>>
> >>>vibration
> >>>
> >>>>>from the drive shaft it seems at around 40 and up. The when I let
> >
> > off
> >
> >>>the
> >>>
> >>>>>gas I hear a noise like a 10 speed bike would make when you are
> >>
> >>coasting
> >>
> >>>>>only heavier, click click click click.... etc.
> >>>>>
> >>>>>The kit came with a transfer case drop kit but I didn't install it.
> >>>>
> >>>>Others
> >>>>
> >>>>>I have talked to said they didn't use the transfer case drop kit.
> >>>>>
> >>>>>Has anyone else had this problem or can anyone give a comment or
> >
> > help?
> >
> >>>>>Thanks,
> >>>>>
> >>>>>
> >>>>
> >>>>
> >>>
> >
> >
>