FARK!
#21
Guest
Posts: n/a
Re: FARK!
man that sucks! have u found anyone else online that has done the swap?
nice cherokee btw. that blower must be nice to have.
"DougW" <post.replies@invalid.address> wrote in message
news:tRYdc.372$fS6.27@okepread01...
> Well, despite what Banks claims, the exhaust header for the
> 93-98 Grand Cherokee doesn't friggin fit.
>
> It hits the motor mount and doesn't even fit the intake
> manifold unless you take a grinder to one or the other.
> I'm not even sure it would match up with the stock downpipe.
>
> Perhaps it works better on later models but it sure as ----
> doesn't work on the ZJ.
>
> Too bad realy, it looked nice and well made.
>
> --
> DougW
> (and his still really busted ZJ)
>
>
>
nice cherokee btw. that blower must be nice to have.
"DougW" <post.replies@invalid.address> wrote in message
news:tRYdc.372$fS6.27@okepread01...
> Well, despite what Banks claims, the exhaust header for the
> 93-98 Grand Cherokee doesn't friggin fit.
>
> It hits the motor mount and doesn't even fit the intake
> manifold unless you take a grinder to one or the other.
> I'm not even sure it would match up with the stock downpipe.
>
> Perhaps it works better on later models but it sure as ----
> doesn't work on the ZJ.
>
> Too bad realy, it looked nice and well made.
>
> --
> DougW
> (and his still really busted ZJ)
>
>
>
#22
Guest
Posts: n/a
Re: FARK!
serg did pass the time by typing:
> man that sucks! have u found anyone else online that has done the swap?
Nope. :( But on the bright side I managed to get it to fit (sorta)
The only holdback is the drivers side engine mount. It's just too
close by about 1/16". I'm going to see if that mount will move a bit
and if it doesn't I'm going to grind off a bit. Seems plenty stout and
should be able to loose some off the edge without harming it.
> nice cherokee btw. that blower must be nice to have.
Sure is. Till I have to put gas in it. :)
> "DougW" wrote in message
> news:tRYdc.372$fS6.27@okepread01...
>> Well, despite what Banks claims, the exhaust header for the
>> 93-98 Grand Cherokee doesn't friggin fit.
>>
>> It hits the motor mount and doesn't even fit the intake
>> manifold unless you take a grinder to one or the other.
>> I'm not even sure it would match up with the stock downpipe.
>>
>> Perhaps it works better on later models but it sure as ----
>> doesn't work on the ZJ.
>>
>> Too bad realy, it looked nice and well made.
> man that sucks! have u found anyone else online that has done the swap?
Nope. :( But on the bright side I managed to get it to fit (sorta)
The only holdback is the drivers side engine mount. It's just too
close by about 1/16". I'm going to see if that mount will move a bit
and if it doesn't I'm going to grind off a bit. Seems plenty stout and
should be able to loose some off the edge without harming it.
> nice cherokee btw. that blower must be nice to have.
Sure is. Till I have to put gas in it. :)
> "DougW" wrote in message
> news:tRYdc.372$fS6.27@okepread01...
>> Well, despite what Banks claims, the exhaust header for the
>> 93-98 Grand Cherokee doesn't friggin fit.
>>
>> It hits the motor mount and doesn't even fit the intake
>> manifold unless you take a grinder to one or the other.
>> I'm not even sure it would match up with the stock downpipe.
>>
>> Perhaps it works better on later models but it sure as ----
>> doesn't work on the ZJ.
>>
>> Too bad realy, it looked nice and well made.
#23
Guest
Posts: n/a
Re: FARK!
serg did pass the time by typing:
> man that sucks! have u found anyone else online that has done the swap?
Nope. :( But on the bright side I managed to get it to fit (sorta)
The only holdback is the drivers side engine mount. It's just too
close by about 1/16". I'm going to see if that mount will move a bit
and if it doesn't I'm going to grind off a bit. Seems plenty stout and
should be able to loose some off the edge without harming it.
> nice cherokee btw. that blower must be nice to have.
Sure is. Till I have to put gas in it. :)
> "DougW" wrote in message
> news:tRYdc.372$fS6.27@okepread01...
>> Well, despite what Banks claims, the exhaust header for the
>> 93-98 Grand Cherokee doesn't friggin fit.
>>
>> It hits the motor mount and doesn't even fit the intake
>> manifold unless you take a grinder to one or the other.
>> I'm not even sure it would match up with the stock downpipe.
>>
>> Perhaps it works better on later models but it sure as ----
>> doesn't work on the ZJ.
>>
>> Too bad realy, it looked nice and well made.
> man that sucks! have u found anyone else online that has done the swap?
Nope. :( But on the bright side I managed to get it to fit (sorta)
The only holdback is the drivers side engine mount. It's just too
close by about 1/16". I'm going to see if that mount will move a bit
and if it doesn't I'm going to grind off a bit. Seems plenty stout and
should be able to loose some off the edge without harming it.
> nice cherokee btw. that blower must be nice to have.
Sure is. Till I have to put gas in it. :)
> "DougW" wrote in message
> news:tRYdc.372$fS6.27@okepread01...
>> Well, despite what Banks claims, the exhaust header for the
>> 93-98 Grand Cherokee doesn't friggin fit.
>>
>> It hits the motor mount and doesn't even fit the intake
>> manifold unless you take a grinder to one or the other.
>> I'm not even sure it would match up with the stock downpipe.
>>
>> Perhaps it works better on later models but it sure as ----
>> doesn't work on the ZJ.
>>
>> Too bad realy, it looked nice and well made.
#24
Guest
Posts: n/a
Re: FARK!
serg did pass the time by typing:
> man that sucks! have u found anyone else online that has done the swap?
Nope. :( But on the bright side I managed to get it to fit (sorta)
The only holdback is the drivers side engine mount. It's just too
close by about 1/16". I'm going to see if that mount will move a bit
and if it doesn't I'm going to grind off a bit. Seems plenty stout and
should be able to loose some off the edge without harming it.
> nice cherokee btw. that blower must be nice to have.
Sure is. Till I have to put gas in it. :)
> "DougW" wrote in message
> news:tRYdc.372$fS6.27@okepread01...
>> Well, despite what Banks claims, the exhaust header for the
>> 93-98 Grand Cherokee doesn't friggin fit.
>>
>> It hits the motor mount and doesn't even fit the intake
>> manifold unless you take a grinder to one or the other.
>> I'm not even sure it would match up with the stock downpipe.
>>
>> Perhaps it works better on later models but it sure as ----
>> doesn't work on the ZJ.
>>
>> Too bad realy, it looked nice and well made.
> man that sucks! have u found anyone else online that has done the swap?
Nope. :( But on the bright side I managed to get it to fit (sorta)
The only holdback is the drivers side engine mount. It's just too
close by about 1/16". I'm going to see if that mount will move a bit
and if it doesn't I'm going to grind off a bit. Seems plenty stout and
should be able to loose some off the edge without harming it.
> nice cherokee btw. that blower must be nice to have.
Sure is. Till I have to put gas in it. :)
> "DougW" wrote in message
> news:tRYdc.372$fS6.27@okepread01...
>> Well, despite what Banks claims, the exhaust header for the
>> 93-98 Grand Cherokee doesn't friggin fit.
>>
>> It hits the motor mount and doesn't even fit the intake
>> manifold unless you take a grinder to one or the other.
>> I'm not even sure it would match up with the stock downpipe.
>>
>> Perhaps it works better on later models but it sure as ----
>> doesn't work on the ZJ.
>>
>> Too bad realy, it looked nice and well made.
#25
Guest
Posts: n/a
Re: FARK!
serg did pass the time by typing:
> man that sucks! have u found anyone else online that has done the swap?
Nope. :( But on the bright side I managed to get it to fit (sorta)
The only holdback is the drivers side engine mount. It's just too
close by about 1/16". I'm going to see if that mount will move a bit
and if it doesn't I'm going to grind off a bit. Seems plenty stout and
should be able to loose some off the edge without harming it.
> nice cherokee btw. that blower must be nice to have.
Sure is. Till I have to put gas in it. :)
> "DougW" wrote in message
> news:tRYdc.372$fS6.27@okepread01...
>> Well, despite what Banks claims, the exhaust header for the
>> 93-98 Grand Cherokee doesn't friggin fit.
>>
>> It hits the motor mount and doesn't even fit the intake
>> manifold unless you take a grinder to one or the other.
>> I'm not even sure it would match up with the stock downpipe.
>>
>> Perhaps it works better on later models but it sure as ----
>> doesn't work on the ZJ.
>>
>> Too bad realy, it looked nice and well made.
> man that sucks! have u found anyone else online that has done the swap?
Nope. :( But on the bright side I managed to get it to fit (sorta)
The only holdback is the drivers side engine mount. It's just too
close by about 1/16". I'm going to see if that mount will move a bit
and if it doesn't I'm going to grind off a bit. Seems plenty stout and
should be able to loose some off the edge without harming it.
> nice cherokee btw. that blower must be nice to have.
Sure is. Till I have to put gas in it. :)
> "DougW" wrote in message
> news:tRYdc.372$fS6.27@okepread01...
>> Well, despite what Banks claims, the exhaust header for the
>> 93-98 Grand Cherokee doesn't friggin fit.
>>
>> It hits the motor mount and doesn't even fit the intake
>> manifold unless you take a grinder to one or the other.
>> I'm not even sure it would match up with the stock downpipe.
>>
>> Perhaps it works better on later models but it sure as ----
>> doesn't work on the ZJ.
>>
>> Too bad realy, it looked nice and well made.