Driveline vibration solved - mostly
06-04-2004, 03:41 PM
#11
Guest
Posts: n/a
Re: Driveline vibration solved - mostly
Hi Bill,
Before you solve your problem with an constant velocity universal
joint, it is important the slope down the output shaft and the slope up
of the pinion angle be the same:
http://www.4xshaft.com/driveline101.html
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
William Oliveri wrote:
>
> Well, looks like I solved 95% of my driveline vibration and just cost me
> 11.00 (plus a bunch of cussing. It's somewhat of a PITA lining up these
> nibs to the perches. I found a sledge hammer works quite well to position
> the spring sideways. The use of a mule kick to position it front to back).
>
> Anyway, I took out the 6 degree shim and dropped the pinion down with a 2
> 1/2 degree shim. Still a tiny bit of vibration there but it's liveable.
> Perhaps in the future I can get a CV shaft if the money is around.
>
> Thanks to all,
>
> Bill
Before you solve your problem with an constant velocity universal
joint, it is important the slope down the output shaft and the slope up
of the pinion angle be the same:
http://www.4xshaft.com/driveline101.html
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
William Oliveri wrote:
>
> Well, looks like I solved 95% of my driveline vibration and just cost me
> 11.00 (plus a bunch of cussing. It's somewhat of a PITA lining up these
> nibs to the perches. I found a sledge hammer works quite well to position
> the spring sideways. The use of a mule kick to position it front to back).
>
> Anyway, I took out the 6 degree shim and dropped the pinion down with a 2
> 1/2 degree shim. Still a tiny bit of vibration there but it's liveable.
> Perhaps in the future I can get a CV shaft if the money is around.
>
> Thanks to all,
>
> Bill
06-04-2004, 03:41 PM
#12
Guest
Posts: n/a
Re: Driveline vibration solved - mostly
Hi Bill,
Before you solve your problem with an constant velocity universal
joint, it is important the slope down the output shaft and the slope up
of the pinion angle be the same:
http://www.4xshaft.com/driveline101.html
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
William Oliveri wrote:
>
> Well, looks like I solved 95% of my driveline vibration and just cost me
> 11.00 (plus a bunch of cussing. It's somewhat of a PITA lining up these
> nibs to the perches. I found a sledge hammer works quite well to position
> the spring sideways. The use of a mule kick to position it front to back).
>
> Anyway, I took out the 6 degree shim and dropped the pinion down with a 2
> 1/2 degree shim. Still a tiny bit of vibration there but it's liveable.
> Perhaps in the future I can get a CV shaft if the money is around.
>
> Thanks to all,
>
> Bill
Before you solve your problem with an constant velocity universal
joint, it is important the slope down the output shaft and the slope up
of the pinion angle be the same:
http://www.4xshaft.com/driveline101.html
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
William Oliveri wrote:
>
> Well, looks like I solved 95% of my driveline vibration and just cost me
> 11.00 (plus a bunch of cussing. It's somewhat of a PITA lining up these
> nibs to the perches. I found a sledge hammer works quite well to position
> the spring sideways. The use of a mule kick to position it front to back).
>
> Anyway, I took out the 6 degree shim and dropped the pinion down with a 2
> 1/2 degree shim. Still a tiny bit of vibration there but it's liveable.
> Perhaps in the future I can get a CV shaft if the money is around.
>
> Thanks to all,
>
> Bill
06-04-2004, 03:41 PM
#13
Guest
Posts: n/a
Re: Driveline vibration solved - mostly
Hi Bill,
Before you solve your problem with an constant velocity universal
joint, it is important the slope down the output shaft and the slope up
of the pinion angle be the same:
http://www.4xshaft.com/driveline101.html
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
William Oliveri wrote:
>
> Well, looks like I solved 95% of my driveline vibration and just cost me
> 11.00 (plus a bunch of cussing. It's somewhat of a PITA lining up these
> nibs to the perches. I found a sledge hammer works quite well to position
> the spring sideways. The use of a mule kick to position it front to back).
>
> Anyway, I took out the 6 degree shim and dropped the pinion down with a 2
> 1/2 degree shim. Still a tiny bit of vibration there but it's liveable.
> Perhaps in the future I can get a CV shaft if the money is around.
>
> Thanks to all,
>
> Bill
Before you solve your problem with an constant velocity universal
joint, it is important the slope down the output shaft and the slope up
of the pinion angle be the same:
http://www.4xshaft.com/driveline101.html
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
William Oliveri wrote:
>
> Well, looks like I solved 95% of my driveline vibration and just cost me
> 11.00 (plus a bunch of cussing. It's somewhat of a PITA lining up these
> nibs to the perches. I found a sledge hammer works quite well to position
> the spring sideways. The use of a mule kick to position it front to back).
>
> Anyway, I took out the 6 degree shim and dropped the pinion down with a 2
> 1/2 degree shim. Still a tiny bit of vibration there but it's liveable.
> Perhaps in the future I can get a CV shaft if the money is around.
>
> Thanks to all,
>
> Bill
06-04-2004, 03:59 PM
#14
Guest
Posts: n/a
Re: Driveline vibration solved - mostly
Go to the hardware store and get an angle finder (they don't cost much)
to see how close you got on your slipyoke/pinion angles. Maybe you can
get them closer. Have you tried running with no shims? You did drop the
tcase skid 3/4", right? If your slipyoke/pinion angles are indeed bang
on, then your steep drive shaft angle is likely the cause of remaining
vibes and you'll know you've done all you can short of a fixed yoke and
double cardan shaft.
Steve
William Oliveri wrote:
> No. I more or less guessed and got pretty close. They only offered a 4
> degree shim and a 2 1/2 degree shim so I guessed at the 2 1/2 degree shim.
>
> You mean to determine if my shaft is within the 15 degree angle?
to see how close you got on your slipyoke/pinion angles. Maybe you can
get them closer. Have you tried running with no shims? You did drop the
tcase skid 3/4", right? If your slipyoke/pinion angles are indeed bang
on, then your steep drive shaft angle is likely the cause of remaining
vibes and you'll know you've done all you can short of a fixed yoke and
double cardan shaft.
Steve
William Oliveri wrote:
> No. I more or less guessed and got pretty close. They only offered a 4
> degree shim and a 2 1/2 degree shim so I guessed at the 2 1/2 degree shim.
>
> You mean to determine if my shaft is within the 15 degree angle?
06-04-2004, 03:59 PM
#15
Guest
Posts: n/a
Re: Driveline vibration solved - mostly
Go to the hardware store and get an angle finder (they don't cost much)
to see how close you got on your slipyoke/pinion angles. Maybe you can
get them closer. Have you tried running with no shims? You did drop the
tcase skid 3/4", right? If your slipyoke/pinion angles are indeed bang
on, then your steep drive shaft angle is likely the cause of remaining
vibes and you'll know you've done all you can short of a fixed yoke and
double cardan shaft.
Steve
William Oliveri wrote:
> No. I more or less guessed and got pretty close. They only offered a 4
> degree shim and a 2 1/2 degree shim so I guessed at the 2 1/2 degree shim.
>
> You mean to determine if my shaft is within the 15 degree angle?
to see how close you got on your slipyoke/pinion angles. Maybe you can
get them closer. Have you tried running with no shims? You did drop the
tcase skid 3/4", right? If your slipyoke/pinion angles are indeed bang
on, then your steep drive shaft angle is likely the cause of remaining
vibes and you'll know you've done all you can short of a fixed yoke and
double cardan shaft.
Steve
William Oliveri wrote:
> No. I more or less guessed and got pretty close. They only offered a 4
> degree shim and a 2 1/2 degree shim so I guessed at the 2 1/2 degree shim.
>
> You mean to determine if my shaft is within the 15 degree angle?
06-04-2004, 03:59 PM
#16
Guest
Posts: n/a
Re: Driveline vibration solved - mostly
Go to the hardware store and get an angle finder (they don't cost much)
to see how close you got on your slipyoke/pinion angles. Maybe you can
get them closer. Have you tried running with no shims? You did drop the
tcase skid 3/4", right? If your slipyoke/pinion angles are indeed bang
on, then your steep drive shaft angle is likely the cause of remaining
vibes and you'll know you've done all you can short of a fixed yoke and
double cardan shaft.
Steve
William Oliveri wrote:
> No. I more or less guessed and got pretty close. They only offered a 4
> degree shim and a 2 1/2 degree shim so I guessed at the 2 1/2 degree shim.
>
> You mean to determine if my shaft is within the 15 degree angle?
to see how close you got on your slipyoke/pinion angles. Maybe you can
get them closer. Have you tried running with no shims? You did drop the
tcase skid 3/4", right? If your slipyoke/pinion angles are indeed bang
on, then your steep drive shaft angle is likely the cause of remaining
vibes and you'll know you've done all you can short of a fixed yoke and
double cardan shaft.
Steve
William Oliveri wrote:
> No. I more or less guessed and got pretty close. They only offered a 4
> degree shim and a 2 1/2 degree shim so I guessed at the 2 1/2 degree shim.
>
> You mean to determine if my shaft is within the 15 degree angle?
06-04-2004, 03:59 PM
#17
Guest
Posts: n/a
Re: Driveline vibration solved - mostly
Go to the hardware store and get an angle finder (they don't cost much)
to see how close you got on your slipyoke/pinion angles. Maybe you can
get them closer. Have you tried running with no shims? You did drop the
tcase skid 3/4", right? If your slipyoke/pinion angles are indeed bang
on, then your steep drive shaft angle is likely the cause of remaining
vibes and you'll know you've done all you can short of a fixed yoke and
double cardan shaft.
Steve
William Oliveri wrote:
> No. I more or less guessed and got pretty close. They only offered a 4
> degree shim and a 2 1/2 degree shim so I guessed at the 2 1/2 degree shim.
>
> You mean to determine if my shaft is within the 15 degree angle?
to see how close you got on your slipyoke/pinion angles. Maybe you can
get them closer. Have you tried running with no shims? You did drop the
tcase skid 3/4", right? If your slipyoke/pinion angles are indeed bang
on, then your steep drive shaft angle is likely the cause of remaining
vibes and you'll know you've done all you can short of a fixed yoke and
double cardan shaft.
Steve
William Oliveri wrote:
> No. I more or less guessed and got pretty close. They only offered a 4
> degree shim and a 2 1/2 degree shim so I guessed at the 2 1/2 degree shim.
>
> You mean to determine if my shaft is within the 15 degree angle?
06-04-2004, 04:03 PM
#18
Guest
Posts: n/a
Re: Driveline vibration solved - mostly
Exactly. Before I went the shim route, the angle at the pinion and
driveshaft was virtually non-existent. About 0 degrees. Would have been
perfect for the CV Shaft only I don't have an extra 400.00 for the shaft and
yolk to spend at this time. The 11.00 shim set is a worthy fix for now.
Bill
"L.W. (ßill) ------ III" <----------@***.net> wrote in message
news:40C0D061.84E5F5C2@***.net...
> Hi Bill,
> Before you solve your problem with an constant velocity universal
> joint, it is important the slope down the output shaft and the slope up
> of the pinion angle be the same:
> http://www.4xshaft.com/driveline101.html
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
> William Oliveri wrote:
> >
> > Well, looks like I solved 95% of my driveline vibration and just cost me
> > 11.00 (plus a bunch of cussing. It's somewhat of a PITA lining up these
> > nibs to the perches. I found a sledge hammer works quite well to
position
> > the spring sideways. The use of a mule kick to position it front to
back).
> >
> > Anyway, I took out the 6 degree shim and dropped the pinion down with a
2
> > 1/2 degree shim. Still a tiny bit of vibration there but it's liveable.
> > Perhaps in the future I can get a CV shaft if the money is around.
> >
> > Thanks to all,
> >
> > Bill
driveshaft was virtually non-existent. About 0 degrees. Would have been
perfect for the CV Shaft only I don't have an extra 400.00 for the shaft and
yolk to spend at this time. The 11.00 shim set is a worthy fix for now.
Bill
"L.W. (ßill) ------ III" <----------@***.net> wrote in message
news:40C0D061.84E5F5C2@***.net...
> Hi Bill,
> Before you solve your problem with an constant velocity universal
> joint, it is important the slope down the output shaft and the slope up
> of the pinion angle be the same:
> http://www.4xshaft.com/driveline101.html
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
> William Oliveri wrote:
> >
> > Well, looks like I solved 95% of my driveline vibration and just cost me
> > 11.00 (plus a bunch of cussing. It's somewhat of a PITA lining up these
> > nibs to the perches. I found a sledge hammer works quite well to
position
> > the spring sideways. The use of a mule kick to position it front to
back).
> >
> > Anyway, I took out the 6 degree shim and dropped the pinion down with a
2
> > 1/2 degree shim. Still a tiny bit of vibration there but it's liveable.
> > Perhaps in the future I can get a CV shaft if the money is around.
> >
> > Thanks to all,
> >
> > Bill
06-04-2004, 04:03 PM
#19
Guest
Posts: n/a
Re: Driveline vibration solved - mostly
Exactly. Before I went the shim route, the angle at the pinion and
driveshaft was virtually non-existent. About 0 degrees. Would have been
perfect for the CV Shaft only I don't have an extra 400.00 for the shaft and
yolk to spend at this time. The 11.00 shim set is a worthy fix for now.
Bill
"L.W. (ßill) ------ III" <----------@***.net> wrote in message
news:40C0D061.84E5F5C2@***.net...
> Hi Bill,
> Before you solve your problem with an constant velocity universal
> joint, it is important the slope down the output shaft and the slope up
> of the pinion angle be the same:
> http://www.4xshaft.com/driveline101.html
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
> William Oliveri wrote:
> >
> > Well, looks like I solved 95% of my driveline vibration and just cost me
> > 11.00 (plus a bunch of cussing. It's somewhat of a PITA lining up these
> > nibs to the perches. I found a sledge hammer works quite well to
position
> > the spring sideways. The use of a mule kick to position it front to
back).
> >
> > Anyway, I took out the 6 degree shim and dropped the pinion down with a
2
> > 1/2 degree shim. Still a tiny bit of vibration there but it's liveable.
> > Perhaps in the future I can get a CV shaft if the money is around.
> >
> > Thanks to all,
> >
> > Bill
driveshaft was virtually non-existent. About 0 degrees. Would have been
perfect for the CV Shaft only I don't have an extra 400.00 for the shaft and
yolk to spend at this time. The 11.00 shim set is a worthy fix for now.
Bill
"L.W. (ßill) ------ III" <----------@***.net> wrote in message
news:40C0D061.84E5F5C2@***.net...
> Hi Bill,
> Before you solve your problem with an constant velocity universal
> joint, it is important the slope down the output shaft and the slope up
> of the pinion angle be the same:
> http://www.4xshaft.com/driveline101.html
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
> William Oliveri wrote:
> >
> > Well, looks like I solved 95% of my driveline vibration and just cost me
> > 11.00 (plus a bunch of cussing. It's somewhat of a PITA lining up these
> > nibs to the perches. I found a sledge hammer works quite well to
position
> > the spring sideways. The use of a mule kick to position it front to
back).
> >
> > Anyway, I took out the 6 degree shim and dropped the pinion down with a
2
> > 1/2 degree shim. Still a tiny bit of vibration there but it's liveable.
> > Perhaps in the future I can get a CV shaft if the money is around.
> >
> > Thanks to all,
> >
> > Bill
06-04-2004, 04:03 PM
#20
Guest
Posts: n/a
Re: Driveline vibration solved - mostly
Exactly. Before I went the shim route, the angle at the pinion and
driveshaft was virtually non-existent. About 0 degrees. Would have been
perfect for the CV Shaft only I don't have an extra 400.00 for the shaft and
yolk to spend at this time. The 11.00 shim set is a worthy fix for now.
Bill
"L.W. (ßill) ------ III" <----------@***.net> wrote in message
news:40C0D061.84E5F5C2@***.net...
> Hi Bill,
> Before you solve your problem with an constant velocity universal
> joint, it is important the slope down the output shaft and the slope up
> of the pinion angle be the same:
> http://www.4xshaft.com/driveline101.html
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
> William Oliveri wrote:
> >
> > Well, looks like I solved 95% of my driveline vibration and just cost me
> > 11.00 (plus a bunch of cussing. It's somewhat of a PITA lining up these
> > nibs to the perches. I found a sledge hammer works quite well to
position
> > the spring sideways. The use of a mule kick to position it front to
back).
> >
> > Anyway, I took out the 6 degree shim and dropped the pinion down with a
2
> > 1/2 degree shim. Still a tiny bit of vibration there but it's liveable.
> > Perhaps in the future I can get a CV shaft if the money is around.
> >
> > Thanks to all,
> >
> > Bill
driveshaft was virtually non-existent. About 0 degrees. Would have been
perfect for the CV Shaft only I don't have an extra 400.00 for the shaft and
yolk to spend at this time. The 11.00 shim set is a worthy fix for now.
Bill
"L.W. (ßill) ------ III" <----------@***.net> wrote in message
news:40C0D061.84E5F5C2@***.net...
> Hi Bill,
> Before you solve your problem with an constant velocity universal
> joint, it is important the slope down the output shaft and the slope up
> of the pinion angle be the same:
> http://www.4xshaft.com/driveline101.html
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
> William Oliveri wrote:
> >
> > Well, looks like I solved 95% of my driveline vibration and just cost me
> > 11.00 (plus a bunch of cussing. It's somewhat of a PITA lining up these
> > nibs to the perches. I found a sledge hammer works quite well to
position
> > the spring sideways. The use of a mule kick to position it front to
back).
> >
> > Anyway, I took out the 6 degree shim and dropped the pinion down with a
2
> > 1/2 degree shim. Still a tiny bit of vibration there but it's liveable.
> > Perhaps in the future I can get a CV shaft if the money is around.
> >
> > Thanks to all,
> >
> > Bill