William Oliveri

83 CJ7, Dana 300


My CV Shaft guy is telling me the correct yoke is Spicer 2-4-4061X. When I
did a search on this part I came up with references to Dana 20 transfer
cases. Are these yoke parts interchangeable or should I be using another
yoke?

Thanks for any help.

Bill

L.W.(=?iso-8859-1?Q?=DFill?=) Hughes III

Hi Bill,
Most Dana 20s are 1 1/8" ten spline, but there are smaller twenty
six spline that are the same. Might take this opportunity to upgrade to
thirty two spline:
http://www.rockcrawler.com/techrepor...line/index.asp
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/

William Oliveri wrote:
>
> 83 CJ7, Dana 300
>
> My CV Shaft guy is telling me the correct yoke is Spicer 2-4-4061X. When I
> did a search on this part I came up with references to Dana 20 transfer
> cases. Are these yoke parts interchangeable or should I be using another
> yoke?
>
> Thanks for any help.
>
> Bill

L.W.(=?iso-8859-1?Q?=DFill?=) Hughes III

Hi Bill,
Most Dana 20s are 1 1/8" ten spline, but there are smaller twenty
six spline that are the same. Might take this opportunity to upgrade to
thirty two spline:
http://www.rockcrawler.com/techrepor...line/index.asp
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/

William Oliveri wrote:
>
> 83 CJ7, Dana 300
>
> My CV Shaft guy is telling me the correct yoke is Spicer 2-4-4061X. When I
> did a search on this part I came up with references to Dana 20 transfer
> cases. Are these yoke parts interchangeable or should I be using another
> yoke?
>
> Thanks for any help.
>
> Bill

L.W.(=?iso-8859-1?Q?=DFill?=) Hughes III

Hi Bill,
Most Dana 20s are 1 1/8" ten spline, but there are smaller twenty
six spline that are the same. Might take this opportunity to upgrade to
thirty two spline:
http://www.rockcrawler.com/techrepor...line/index.asp
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/

William Oliveri wrote:
>
> 83 CJ7, Dana 300
>
> My CV Shaft guy is telling me the correct yoke is Spicer 2-4-4061X. When I
> did a search on this part I came up with references to Dana 20 transfer
> cases. Are these yoke parts interchangeable or should I be using another
> yoke?
>
> Thanks for any help.
>
> Bill

Don Wallish

I took the front output yoke off a Quadra-Trac (i think it was the front) and
it slipped right on the rear of my Dana 300. A front XJ Cherokee driveshaft
bolted right up and was the right length on the back my CJ8.

Don W

Don Wallish

I took the front output yoke off a Quadra-Trac (i think it was the front) and
it slipped right on the rear of my Dana 300. A front XJ Cherokee driveshaft
bolted right up and was the right length on the back my CJ8.

Don W

Don Wallish

I took the front output yoke off a Quadra-Trac (i think it was the front) and
it slipped right on the rear of my Dana 300. A front XJ Cherokee driveshaft
bolted right up and was the right length on the back my CJ8.

Don W