clutch or transmission trouble
#51
Guest
Posts: n/a
Re: clutch or transmission trouble
That manual transmission does not use hydraulics. It may be installed with
a clutch/bell housing that use hydraulics. The 79 CJ did not come original
with a hydraulic clutch.
The OP needs to give us some more information.
JimG
"jdarg" <ruhle@hotmail.com> wrote in message
news:yO4%b.9286736$Of.1529235@news.easynews.com...
> NV4500 uses hydraulics.
>
> "JimG" <jimg@2muchspam.com> wrote in message
> news:HvQ_b.196$yA1.12@news02.roc.ny...
> > The OP said it was a "25 year old Jeep", which will not have a hydraulic
> > clutch.
> >
> > JimG
> >
> > "jdarg" <ruhle@hotmail.com> wrote in message
> > news:R2Q_b.1054261$9p3.196040@news.easynews.com...
> > > Clutch isn't releasing all the way. It's either a hydraulic problem
(low
> > > fluid, bad slave, bad master, etc.) or possibly the clutch disc
> hanging-up
> > > on the tranny input shaft because of rust, wear, etc. I had the latter
> > > problem on my 94 when I first bought it - previous owner let it sit
for
> > > about a year which caused the clutch to "almost" disengage completely
> > after
> > > it warmed up. The tranny input shaft just needed a bit of grease to
make
> > > that disc slide well again. Working fine for almost two years since.
10K
> > is
> > > pretty soon to have issues with the clutch hanging up though unless
> you've
> > > been through lots of messy stuff or it wasn't done right the first
time,
> > so
> > > I'd probably suspect hydraulic issues first.
> > >
> > > -jd
> > >
> > > "sm3gurpal" <elambeth@hotmail.com> wrote in message
> > > news:88f4ec61.0402232000.2ac26e94@posting.google.c om...
> > > > Over the last 2-3 days of moderate highway driving, my manual
> > > > transmission jeep has gotten noticeably harder and harder to shift
> > > > (not wanting to go into gear, especially the lower gears.)
Yesterday,
> > > > I was having to double, triple, and quadruple clutch just to get it
> > > > to go into gear.
> > > >
> > > > Today I started it up and went to drive it, starting it on a level
> > > > surface. In doing so I noticed that even when the clutch is all the
> > > > way to the floor... the jeep is still pulling lightly forward in
1st
> > > > and 2nd gear, and backward in reverse!
> > > >
> > > > Holy crap! It's not supposed to do that when the clutch is all the
> > > > way in!!!
> > > >
> > > > I suspect I've probably got major transmission problems, but I
thought
> > > > I would ask here and see if there are any relatively simple
> > > > quick-fixes I could try first, before I turn my wallet over to a
> > > > transmission shop.
> > > >
> > > > This is a 25 year old jeep, but the transmission and clutch (NV4500
> > > > and Centerforce III) are allegedly new as of 10,000 miles ago.
> > >
> > >
> >
> >
>
>
a clutch/bell housing that use hydraulics. The 79 CJ did not come original
with a hydraulic clutch.
The OP needs to give us some more information.
JimG
"jdarg" <ruhle@hotmail.com> wrote in message
news:yO4%b.9286736$Of.1529235@news.easynews.com...
> NV4500 uses hydraulics.
>
> "JimG" <jimg@2muchspam.com> wrote in message
> news:HvQ_b.196$yA1.12@news02.roc.ny...
> > The OP said it was a "25 year old Jeep", which will not have a hydraulic
> > clutch.
> >
> > JimG
> >
> > "jdarg" <ruhle@hotmail.com> wrote in message
> > news:R2Q_b.1054261$9p3.196040@news.easynews.com...
> > > Clutch isn't releasing all the way. It's either a hydraulic problem
(low
> > > fluid, bad slave, bad master, etc.) or possibly the clutch disc
> hanging-up
> > > on the tranny input shaft because of rust, wear, etc. I had the latter
> > > problem on my 94 when I first bought it - previous owner let it sit
for
> > > about a year which caused the clutch to "almost" disengage completely
> > after
> > > it warmed up. The tranny input shaft just needed a bit of grease to
make
> > > that disc slide well again. Working fine for almost two years since.
10K
> > is
> > > pretty soon to have issues with the clutch hanging up though unless
> you've
> > > been through lots of messy stuff or it wasn't done right the first
time,
> > so
> > > I'd probably suspect hydraulic issues first.
> > >
> > > -jd
> > >
> > > "sm3gurpal" <elambeth@hotmail.com> wrote in message
> > > news:88f4ec61.0402232000.2ac26e94@posting.google.c om...
> > > > Over the last 2-3 days of moderate highway driving, my manual
> > > > transmission jeep has gotten noticeably harder and harder to shift
> > > > (not wanting to go into gear, especially the lower gears.)
Yesterday,
> > > > I was having to double, triple, and quadruple clutch just to get it
> > > > to go into gear.
> > > >
> > > > Today I started it up and went to drive it, starting it on a level
> > > > surface. In doing so I noticed that even when the clutch is all the
> > > > way to the floor... the jeep is still pulling lightly forward in
1st
> > > > and 2nd gear, and backward in reverse!
> > > >
> > > > Holy crap! It's not supposed to do that when the clutch is all the
> > > > way in!!!
> > > >
> > > > I suspect I've probably got major transmission problems, but I
thought
> > > > I would ask here and see if there are any relatively simple
> > > > quick-fixes I could try first, before I turn my wallet over to a
> > > > transmission shop.
> > > >
> > > > This is a 25 year old jeep, but the transmission and clutch (NV4500
> > > > and Centerforce III) are allegedly new as of 10,000 miles ago.
> > >
> > >
> >
> >
>
>
#52
Guest
Posts: n/a
Re: clutch or transmission trouble
That manual transmission does not use hydraulics. It may be installed with
a clutch/bell housing that use hydraulics. The 79 CJ did not come original
with a hydraulic clutch.
The OP needs to give us some more information.
JimG
"jdarg" <ruhle@hotmail.com> wrote in message
news:yO4%b.9286736$Of.1529235@news.easynews.com...
> NV4500 uses hydraulics.
>
> "JimG" <jimg@2muchspam.com> wrote in message
> news:HvQ_b.196$yA1.12@news02.roc.ny...
> > The OP said it was a "25 year old Jeep", which will not have a hydraulic
> > clutch.
> >
> > JimG
> >
> > "jdarg" <ruhle@hotmail.com> wrote in message
> > news:R2Q_b.1054261$9p3.196040@news.easynews.com...
> > > Clutch isn't releasing all the way. It's either a hydraulic problem
(low
> > > fluid, bad slave, bad master, etc.) or possibly the clutch disc
> hanging-up
> > > on the tranny input shaft because of rust, wear, etc. I had the latter
> > > problem on my 94 when I first bought it - previous owner let it sit
for
> > > about a year which caused the clutch to "almost" disengage completely
> > after
> > > it warmed up. The tranny input shaft just needed a bit of grease to
make
> > > that disc slide well again. Working fine for almost two years since.
10K
> > is
> > > pretty soon to have issues with the clutch hanging up though unless
> you've
> > > been through lots of messy stuff or it wasn't done right the first
time,
> > so
> > > I'd probably suspect hydraulic issues first.
> > >
> > > -jd
> > >
> > > "sm3gurpal" <elambeth@hotmail.com> wrote in message
> > > news:88f4ec61.0402232000.2ac26e94@posting.google.c om...
> > > > Over the last 2-3 days of moderate highway driving, my manual
> > > > transmission jeep has gotten noticeably harder and harder to shift
> > > > (not wanting to go into gear, especially the lower gears.)
Yesterday,
> > > > I was having to double, triple, and quadruple clutch just to get it
> > > > to go into gear.
> > > >
> > > > Today I started it up and went to drive it, starting it on a level
> > > > surface. In doing so I noticed that even when the clutch is all the
> > > > way to the floor... the jeep is still pulling lightly forward in
1st
> > > > and 2nd gear, and backward in reverse!
> > > >
> > > > Holy crap! It's not supposed to do that when the clutch is all the
> > > > way in!!!
> > > >
> > > > I suspect I've probably got major transmission problems, but I
thought
> > > > I would ask here and see if there are any relatively simple
> > > > quick-fixes I could try first, before I turn my wallet over to a
> > > > transmission shop.
> > > >
> > > > This is a 25 year old jeep, but the transmission and clutch (NV4500
> > > > and Centerforce III) are allegedly new as of 10,000 miles ago.
> > >
> > >
> >
> >
>
>
a clutch/bell housing that use hydraulics. The 79 CJ did not come original
with a hydraulic clutch.
The OP needs to give us some more information.
JimG
"jdarg" <ruhle@hotmail.com> wrote in message
news:yO4%b.9286736$Of.1529235@news.easynews.com...
> NV4500 uses hydraulics.
>
> "JimG" <jimg@2muchspam.com> wrote in message
> news:HvQ_b.196$yA1.12@news02.roc.ny...
> > The OP said it was a "25 year old Jeep", which will not have a hydraulic
> > clutch.
> >
> > JimG
> >
> > "jdarg" <ruhle@hotmail.com> wrote in message
> > news:R2Q_b.1054261$9p3.196040@news.easynews.com...
> > > Clutch isn't releasing all the way. It's either a hydraulic problem
(low
> > > fluid, bad slave, bad master, etc.) or possibly the clutch disc
> hanging-up
> > > on the tranny input shaft because of rust, wear, etc. I had the latter
> > > problem on my 94 when I first bought it - previous owner let it sit
for
> > > about a year which caused the clutch to "almost" disengage completely
> > after
> > > it warmed up. The tranny input shaft just needed a bit of grease to
make
> > > that disc slide well again. Working fine for almost two years since.
10K
> > is
> > > pretty soon to have issues with the clutch hanging up though unless
> you've
> > > been through lots of messy stuff or it wasn't done right the first
time,
> > so
> > > I'd probably suspect hydraulic issues first.
> > >
> > > -jd
> > >
> > > "sm3gurpal" <elambeth@hotmail.com> wrote in message
> > > news:88f4ec61.0402232000.2ac26e94@posting.google.c om...
> > > > Over the last 2-3 days of moderate highway driving, my manual
> > > > transmission jeep has gotten noticeably harder and harder to shift
> > > > (not wanting to go into gear, especially the lower gears.)
Yesterday,
> > > > I was having to double, triple, and quadruple clutch just to get it
> > > > to go into gear.
> > > >
> > > > Today I started it up and went to drive it, starting it on a level
> > > > surface. In doing so I noticed that even when the clutch is all the
> > > > way to the floor... the jeep is still pulling lightly forward in
1st
> > > > and 2nd gear, and backward in reverse!
> > > >
> > > > Holy crap! It's not supposed to do that when the clutch is all the
> > > > way in!!!
> > > >
> > > > I suspect I've probably got major transmission problems, but I
thought
> > > > I would ask here and see if there are any relatively simple
> > > > quick-fixes I could try first, before I turn my wallet over to a
> > > > transmission shop.
> > > >
> > > > This is a 25 year old jeep, but the transmission and clutch (NV4500
> > > > and Centerforce III) are allegedly new as of 10,000 miles ago.
> > >
> > >
> >
> >
>
>
#53
Guest
Posts: n/a
Re: clutch or transmission trouble
Oh... sorry, you tell us it was a NV4500 transmission.
Has it been fitted with a hydraulic clutch or not?
JimG
"JimG" <jimg@cj7_2muchspam.com> wrote in message
news:Gy1%b.323$V45.192@news02.roc.ny...
> I was referring to the model of the Jeep... is it a 79? It would help if
> you let us know exactly what you have (make, model, engine, transmission).
>
> Your clutch is definitely not adjusted properly or the linkage is
defective.
>
> JimG
>
> "sm3gurpal" <elambeth@hotmail.com> wrote in message
> news:88f4ec61.0402242012.7a3c4eb1@posting.google.c om...
> > > I suspect you have clutch issues not transmission. Does it grind when
> > > trying to go into reverse at a standstill?
> > >
> >
> > Most definitely... assuming I can even get it into gear. (I have
> > been having to turn off the ignition and shift it with nothing running
> > to get it to go in.)
> >
> >
> > > > This is a 25 year old jeep, but the transmission and clutch (NV4500
> > > > and Centerforce III) are allegedly new as of 10,000 miles ago.
> > >
> > > That makes it a 79 model (or so), so there will not be any hydraulics
> > > associated with the clutch.
> >
> > Yes but as I said, it is an aftermarket Centerforce III clutch, much
> > newer than 79.
> >
> >
> > It may just be a linkage adjustment. When you
> > > release the clutch, where does it begin to catch in relation to the
> > > floorboard?
> >
> > Not sure I understand your question. It is still engaged slightly
> > even when the clutch is all the way depressed; I can't get it to
> > disengage.
>
>
Has it been fitted with a hydraulic clutch or not?
JimG
"JimG" <jimg@cj7_2muchspam.com> wrote in message
news:Gy1%b.323$V45.192@news02.roc.ny...
> I was referring to the model of the Jeep... is it a 79? It would help if
> you let us know exactly what you have (make, model, engine, transmission).
>
> Your clutch is definitely not adjusted properly or the linkage is
defective.
>
> JimG
>
> "sm3gurpal" <elambeth@hotmail.com> wrote in message
> news:88f4ec61.0402242012.7a3c4eb1@posting.google.c om...
> > > I suspect you have clutch issues not transmission. Does it grind when
> > > trying to go into reverse at a standstill?
> > >
> >
> > Most definitely... assuming I can even get it into gear. (I have
> > been having to turn off the ignition and shift it with nothing running
> > to get it to go in.)
> >
> >
> > > > This is a 25 year old jeep, but the transmission and clutch (NV4500
> > > > and Centerforce III) are allegedly new as of 10,000 miles ago.
> > >
> > > That makes it a 79 model (or so), so there will not be any hydraulics
> > > associated with the clutch.
> >
> > Yes but as I said, it is an aftermarket Centerforce III clutch, much
> > newer than 79.
> >
> >
> > It may just be a linkage adjustment. When you
> > > release the clutch, where does it begin to catch in relation to the
> > > floorboard?
> >
> > Not sure I understand your question. It is still engaged slightly
> > even when the clutch is all the way depressed; I can't get it to
> > disengage.
>
>
#54
Guest
Posts: n/a
Re: clutch or transmission trouble
Oh... sorry, you tell us it was a NV4500 transmission.
Has it been fitted with a hydraulic clutch or not?
JimG
"JimG" <jimg@cj7_2muchspam.com> wrote in message
news:Gy1%b.323$V45.192@news02.roc.ny...
> I was referring to the model of the Jeep... is it a 79? It would help if
> you let us know exactly what you have (make, model, engine, transmission).
>
> Your clutch is definitely not adjusted properly or the linkage is
defective.
>
> JimG
>
> "sm3gurpal" <elambeth@hotmail.com> wrote in message
> news:88f4ec61.0402242012.7a3c4eb1@posting.google.c om...
> > > I suspect you have clutch issues not transmission. Does it grind when
> > > trying to go into reverse at a standstill?
> > >
> >
> > Most definitely... assuming I can even get it into gear. (I have
> > been having to turn off the ignition and shift it with nothing running
> > to get it to go in.)
> >
> >
> > > > This is a 25 year old jeep, but the transmission and clutch (NV4500
> > > > and Centerforce III) are allegedly new as of 10,000 miles ago.
> > >
> > > That makes it a 79 model (or so), so there will not be any hydraulics
> > > associated with the clutch.
> >
> > Yes but as I said, it is an aftermarket Centerforce III clutch, much
> > newer than 79.
> >
> >
> > It may just be a linkage adjustment. When you
> > > release the clutch, where does it begin to catch in relation to the
> > > floorboard?
> >
> > Not sure I understand your question. It is still engaged slightly
> > even when the clutch is all the way depressed; I can't get it to
> > disengage.
>
>
Has it been fitted with a hydraulic clutch or not?
JimG
"JimG" <jimg@cj7_2muchspam.com> wrote in message
news:Gy1%b.323$V45.192@news02.roc.ny...
> I was referring to the model of the Jeep... is it a 79? It would help if
> you let us know exactly what you have (make, model, engine, transmission).
>
> Your clutch is definitely not adjusted properly or the linkage is
defective.
>
> JimG
>
> "sm3gurpal" <elambeth@hotmail.com> wrote in message
> news:88f4ec61.0402242012.7a3c4eb1@posting.google.c om...
> > > I suspect you have clutch issues not transmission. Does it grind when
> > > trying to go into reverse at a standstill?
> > >
> >
> > Most definitely... assuming I can even get it into gear. (I have
> > been having to turn off the ignition and shift it with nothing running
> > to get it to go in.)
> >
> >
> > > > This is a 25 year old jeep, but the transmission and clutch (NV4500
> > > > and Centerforce III) are allegedly new as of 10,000 miles ago.
> > >
> > > That makes it a 79 model (or so), so there will not be any hydraulics
> > > associated with the clutch.
> >
> > Yes but as I said, it is an aftermarket Centerforce III clutch, much
> > newer than 79.
> >
> >
> > It may just be a linkage adjustment. When you
> > > release the clutch, where does it begin to catch in relation to the
> > > floorboard?
> >
> > Not sure I understand your question. It is still engaged slightly
> > even when the clutch is all the way depressed; I can't get it to
> > disengage.
>
>
#55
Guest
Posts: n/a
Re: clutch or transmission trouble
Oh... sorry, you tell us it was a NV4500 transmission.
Has it been fitted with a hydraulic clutch or not?
JimG
"JimG" <jimg@cj7_2muchspam.com> wrote in message
news:Gy1%b.323$V45.192@news02.roc.ny...
> I was referring to the model of the Jeep... is it a 79? It would help if
> you let us know exactly what you have (make, model, engine, transmission).
>
> Your clutch is definitely not adjusted properly or the linkage is
defective.
>
> JimG
>
> "sm3gurpal" <elambeth@hotmail.com> wrote in message
> news:88f4ec61.0402242012.7a3c4eb1@posting.google.c om...
> > > I suspect you have clutch issues not transmission. Does it grind when
> > > trying to go into reverse at a standstill?
> > >
> >
> > Most definitely... assuming I can even get it into gear. (I have
> > been having to turn off the ignition and shift it with nothing running
> > to get it to go in.)
> >
> >
> > > > This is a 25 year old jeep, but the transmission and clutch (NV4500
> > > > and Centerforce III) are allegedly new as of 10,000 miles ago.
> > >
> > > That makes it a 79 model (or so), so there will not be any hydraulics
> > > associated with the clutch.
> >
> > Yes but as I said, it is an aftermarket Centerforce III clutch, much
> > newer than 79.
> >
> >
> > It may just be a linkage adjustment. When you
> > > release the clutch, where does it begin to catch in relation to the
> > > floorboard?
> >
> > Not sure I understand your question. It is still engaged slightly
> > even when the clutch is all the way depressed; I can't get it to
> > disengage.
>
>
Has it been fitted with a hydraulic clutch or not?
JimG
"JimG" <jimg@cj7_2muchspam.com> wrote in message
news:Gy1%b.323$V45.192@news02.roc.ny...
> I was referring to the model of the Jeep... is it a 79? It would help if
> you let us know exactly what you have (make, model, engine, transmission).
>
> Your clutch is definitely not adjusted properly or the linkage is
defective.
>
> JimG
>
> "sm3gurpal" <elambeth@hotmail.com> wrote in message
> news:88f4ec61.0402242012.7a3c4eb1@posting.google.c om...
> > > I suspect you have clutch issues not transmission. Does it grind when
> > > trying to go into reverse at a standstill?
> > >
> >
> > Most definitely... assuming I can even get it into gear. (I have
> > been having to turn off the ignition and shift it with nothing running
> > to get it to go in.)
> >
> >
> > > > This is a 25 year old jeep, but the transmission and clutch (NV4500
> > > > and Centerforce III) are allegedly new as of 10,000 miles ago.
> > >
> > > That makes it a 79 model (or so), so there will not be any hydraulics
> > > associated with the clutch.
> >
> > Yes but as I said, it is an aftermarket Centerforce III clutch, much
> > newer than 79.
> >
> >
> > It may just be a linkage adjustment. When you
> > > release the clutch, where does it begin to catch in relation to the
> > > floorboard?
> >
> > Not sure I understand your question. It is still engaged slightly
> > even when the clutch is all the way depressed; I can't get it to
> > disengage.
>
>
#56
Guest
Posts: n/a
Re: clutch or transmission trouble
The problem is that I don't know enough to know what I'm looking at.
(I did not put this jeep together, I am like the 5th owner.) I have
been reliably informed by the previous owner that it has a centerforce
III clutch and NV4500 manual transmission.
If that's not enough info to determine whether it's a manual linkage
or hydraulic, can you folks tell me roughly what I should look for to
figure it out?
I can crawl under there and snap some digital photos and post them to
the web if it would help.
> That manual transmission does not use hydraulics. It may be installed with
> a clutch/bell housing that use hydraulics. The 79 CJ did not come original
> with a hydraulic clutch.
>
> The OP needs to give us some more information.
>
> JimG
>
(I did not put this jeep together, I am like the 5th owner.) I have
been reliably informed by the previous owner that it has a centerforce
III clutch and NV4500 manual transmission.
If that's not enough info to determine whether it's a manual linkage
or hydraulic, can you folks tell me roughly what I should look for to
figure it out?
I can crawl under there and snap some digital photos and post them to
the web if it would help.
> That manual transmission does not use hydraulics. It may be installed with
> a clutch/bell housing that use hydraulics. The 79 CJ did not come original
> with a hydraulic clutch.
>
> The OP needs to give us some more information.
>
> JimG
>
#57
Guest
Posts: n/a
Re: clutch or transmission trouble
The problem is that I don't know enough to know what I'm looking at.
(I did not put this jeep together, I am like the 5th owner.) I have
been reliably informed by the previous owner that it has a centerforce
III clutch and NV4500 manual transmission.
If that's not enough info to determine whether it's a manual linkage
or hydraulic, can you folks tell me roughly what I should look for to
figure it out?
I can crawl under there and snap some digital photos and post them to
the web if it would help.
> That manual transmission does not use hydraulics. It may be installed with
> a clutch/bell housing that use hydraulics. The 79 CJ did not come original
> with a hydraulic clutch.
>
> The OP needs to give us some more information.
>
> JimG
>
(I did not put this jeep together, I am like the 5th owner.) I have
been reliably informed by the previous owner that it has a centerforce
III clutch and NV4500 manual transmission.
If that's not enough info to determine whether it's a manual linkage
or hydraulic, can you folks tell me roughly what I should look for to
figure it out?
I can crawl under there and snap some digital photos and post them to
the web if it would help.
> That manual transmission does not use hydraulics. It may be installed with
> a clutch/bell housing that use hydraulics. The 79 CJ did not come original
> with a hydraulic clutch.
>
> The OP needs to give us some more information.
>
> JimG
>
#58
Guest
Posts: n/a
Re: clutch or transmission trouble
The problem is that I don't know enough to know what I'm looking at.
(I did not put this jeep together, I am like the 5th owner.) I have
been reliably informed by the previous owner that it has a centerforce
III clutch and NV4500 manual transmission.
If that's not enough info to determine whether it's a manual linkage
or hydraulic, can you folks tell me roughly what I should look for to
figure it out?
I can crawl under there and snap some digital photos and post them to
the web if it would help.
> That manual transmission does not use hydraulics. It may be installed with
> a clutch/bell housing that use hydraulics. The 79 CJ did not come original
> with a hydraulic clutch.
>
> The OP needs to give us some more information.
>
> JimG
>
(I did not put this jeep together, I am like the 5th owner.) I have
been reliably informed by the previous owner that it has a centerforce
III clutch and NV4500 manual transmission.
If that's not enough info to determine whether it's a manual linkage
or hydraulic, can you folks tell me roughly what I should look for to
figure it out?
I can crawl under there and snap some digital photos and post them to
the web if it would help.
> That manual transmission does not use hydraulics. It may be installed with
> a clutch/bell housing that use hydraulics. The 79 CJ did not come original
> with a hydraulic clutch.
>
> The OP needs to give us some more information.
>
> JimG
>
#59
Guest
Posts: n/a
Re: clutch or transmission trouble
Pictures would certainly help.
If it is hydraulic, there will be fluid reservoir under the hood on the
drivers side firewall and a plastic line down to the bell housing. There
would also be a line from the clutch pedal to the reservoir.
If is a manual clutch, the pedal will be connected with a steel rod to the
bell crank (a steel tube with wings and grease fittings) and then another
steel rod to the bell housing and clutch fork. This one would be threaded
for adjustment.
--
JimG
80' CJ-7 258 CID
35" BFG MT on 15x10 Centerlines
D44 Rear, Dana 30 Front. SOA
4.56 Gears, LockRight F&R
Dana 300 w/4:1 & Currie twin sticks
Warn X8000i w/ dual batteries
"sm3gurpal" <elambeth@hotmail.com> wrote in message
news:88f4ec61.0402290834.4e3f99b3@posting.google.c om...
> The problem is that I don't know enough to know what I'm looking at.
> (I did not put this jeep together, I am like the 5th owner.) I have
> been reliably informed by the previous owner that it has a centerforce
> III clutch and NV4500 manual transmission.
>
> If that's not enough info to determine whether it's a manual linkage
> or hydraulic, can you folks tell me roughly what I should look for to
> figure it out?
>
> I can crawl under there and snap some digital photos and post them to
> the web if it would help.
>
> > That manual transmission does not use hydraulics. It may be installed
with
> > a clutch/bell housing that use hydraulics. The 79 CJ did not come
original
> > with a hydraulic clutch.
> >
> > The OP needs to give us some more information.
> >
> > JimG
> >
If it is hydraulic, there will be fluid reservoir under the hood on the
drivers side firewall and a plastic line down to the bell housing. There
would also be a line from the clutch pedal to the reservoir.
If is a manual clutch, the pedal will be connected with a steel rod to the
bell crank (a steel tube with wings and grease fittings) and then another
steel rod to the bell housing and clutch fork. This one would be threaded
for adjustment.
--
JimG
80' CJ-7 258 CID
35" BFG MT on 15x10 Centerlines
D44 Rear, Dana 30 Front. SOA
4.56 Gears, LockRight F&R
Dana 300 w/4:1 & Currie twin sticks
Warn X8000i w/ dual batteries
"sm3gurpal" <elambeth@hotmail.com> wrote in message
news:88f4ec61.0402290834.4e3f99b3@posting.google.c om...
> The problem is that I don't know enough to know what I'm looking at.
> (I did not put this jeep together, I am like the 5th owner.) I have
> been reliably informed by the previous owner that it has a centerforce
> III clutch and NV4500 manual transmission.
>
> If that's not enough info to determine whether it's a manual linkage
> or hydraulic, can you folks tell me roughly what I should look for to
> figure it out?
>
> I can crawl under there and snap some digital photos and post them to
> the web if it would help.
>
> > That manual transmission does not use hydraulics. It may be installed
with
> > a clutch/bell housing that use hydraulics. The 79 CJ did not come
original
> > with a hydraulic clutch.
> >
> > The OP needs to give us some more information.
> >
> > JimG
> >
#60
Guest
Posts: n/a
Re: clutch or transmission trouble
Pictures would certainly help.
If it is hydraulic, there will be fluid reservoir under the hood on the
drivers side firewall and a plastic line down to the bell housing. There
would also be a line from the clutch pedal to the reservoir.
If is a manual clutch, the pedal will be connected with a steel rod to the
bell crank (a steel tube with wings and grease fittings) and then another
steel rod to the bell housing and clutch fork. This one would be threaded
for adjustment.
--
JimG
80' CJ-7 258 CID
35" BFG MT on 15x10 Centerlines
D44 Rear, Dana 30 Front. SOA
4.56 Gears, LockRight F&R
Dana 300 w/4:1 & Currie twin sticks
Warn X8000i w/ dual batteries
"sm3gurpal" <elambeth@hotmail.com> wrote in message
news:88f4ec61.0402290834.4e3f99b3@posting.google.c om...
> The problem is that I don't know enough to know what I'm looking at.
> (I did not put this jeep together, I am like the 5th owner.) I have
> been reliably informed by the previous owner that it has a centerforce
> III clutch and NV4500 manual transmission.
>
> If that's not enough info to determine whether it's a manual linkage
> or hydraulic, can you folks tell me roughly what I should look for to
> figure it out?
>
> I can crawl under there and snap some digital photos and post them to
> the web if it would help.
>
> > That manual transmission does not use hydraulics. It may be installed
with
> > a clutch/bell housing that use hydraulics. The 79 CJ did not come
original
> > with a hydraulic clutch.
> >
> > The OP needs to give us some more information.
> >
> > JimG
> >
If it is hydraulic, there will be fluid reservoir under the hood on the
drivers side firewall and a plastic line down to the bell housing. There
would also be a line from the clutch pedal to the reservoir.
If is a manual clutch, the pedal will be connected with a steel rod to the
bell crank (a steel tube with wings and grease fittings) and then another
steel rod to the bell housing and clutch fork. This one would be threaded
for adjustment.
--
JimG
80' CJ-7 258 CID
35" BFG MT on 15x10 Centerlines
D44 Rear, Dana 30 Front. SOA
4.56 Gears, LockRight F&R
Dana 300 w/4:1 & Currie twin sticks
Warn X8000i w/ dual batteries
"sm3gurpal" <elambeth@hotmail.com> wrote in message
news:88f4ec61.0402290834.4e3f99b3@posting.google.c om...
> The problem is that I don't know enough to know what I'm looking at.
> (I did not put this jeep together, I am like the 5th owner.) I have
> been reliably informed by the previous owner that it has a centerforce
> III clutch and NV4500 manual transmission.
>
> If that's not enough info to determine whether it's a manual linkage
> or hydraulic, can you folks tell me roughly what I should look for to
> figure it out?
>
> I can crawl under there and snap some digital photos and post them to
> the web if it would help.
>
> > That manual transmission does not use hydraulics. It may be installed
with
> > a clutch/bell housing that use hydraulics. The 79 CJ did not come
original
> > with a hydraulic clutch.
> >
> > The OP needs to give us some more information.
> >
> > JimG
> >