http://www.wingtechtips.com/TireChange/tirechange.htm

Earle

"Will Honea" <whonea@yahoo.com> wrote in message
news:JxX2tWiP5BNp-pn2-cWQ0fHNWIpId@anon.none.net...
> That reminded me of one I saw years ago on a Model A. It bolted to
> the hub via the lug nuts so you could break the bead then had a center
> slot to pivot the spoon to pull the bead over the rim. Watched a guy
> break the tire, pull the tube, patch it and be on his way in just a
> few minutes. Of course, breaking the bead on a Model A tire was more
> like doing a bicycle tire than one of today's safety rims...
>
> On Mon, 22 Aug 2005 05:33:05 UTC L.W.(ßill) ------ III
> <----------@***.net> wrote:
>
> > This is my bolt to lug or it's hole, over center lug "T" wrench
> > bead breaker bar: http://www.----------.com/beadBuster.jpg
> > God Bless America, ßill O|||||||O
> > mailto:--------------------
> >
> > Will Honea wrote:
> > >
> > > Dad had a tire changer he got from Harbor Freight, of all places, out
> > > on the farm before he passed away 3 years ago. The particular one had
> > > was pretty handy - after he did a lot of welding to set up a decent
> > > base for it. Every other toy changer I've seen/used was more work to
> > > use than a BMFH and a decent set of irons. Well worth a few bucks
> > > just in the time you save by having a decently equipped shop do the
> > > dirty work IMNSHO.
>
>
> --
> Will Honea

 

Ya my first instinct was to winch it out but the last time the girl was
surrounded by about 25 yards of sugar sand all around, except for the ocean
part, where the tide was moving in on her heh heh. I'm running 4.56 gears
w/33's... and she had a stuck mitsubishi 4 door deal buried up to the
underbody... Not from around here apparently cuz no one else was around
that area of the beach. I had to pull her out and across all this sand, and
I think she might have hit the brakes a time or two while doing it.

This jeep is my first manual transmission and I wasn't sure if I could get
more "grip" with the tranny with a higher performance clutch. A buddy has
had a ceramic one put in his mustang and says its a big difference, I'm just
not sure if it would be the same for a jeep? (TJ)

After reading all these posts, I suppose I'll pay a local shop to swap
tires... I wanted my rims on my jeep put on my gf's and I'm getting new
ones, so there'll be 10 rim/swaps going on, and I'm sure I'll want to get
another set of mudders for some special occasion sometime in the future.

I have seen where they fill the tire with ether and blow it up on the rim,
anyone have any luck with that?

Troy


"Earle Horton" <nurse--NOSPAM--busters@msn.com> wrote in message
news:1124654684.3caff463c37cb8703941f1e8eafa8892@t eranews...
> Things that might help your clutch are a winch, and regearing the axles.
> What gear ratio is it now? A clutch is not really designed to deliver
> power
> while slipping. Really, there are two legitimate positions for the clutch
> pedal, down and up.
>
> I have used toy tire changers before. They are not much fun.
>
> Earle
>
> "Troy" <troy@ .> wrote in message
> news:teGdnQZM-MTNSZXeRVn-uA@comcast.com...
>> When I have to someday replace my clutch in my TJ, are there any "heavy
>> duty" clutches I can get for it? Something that would grip a bit better
>> than stock? I noticed I can't pull vehicles too large outta sand without
>> burning my stock one up a bit.
>>
>>
>> Also, I've seen manual tire changers on the internet, are they worth a
> damn?
>> Or should I just buddy up with a tire shop here in town for swapping
>> tires
>> on rims? I saw this one: http://www.wikco.com/Tire.html
>>
>> Troy
>>
>>
>
>

 

Ya my first instinct was to winch it out but the last time the girl was
surrounded by about 25 yards of sugar sand all around, except for the ocean
part, where the tide was moving in on her heh heh. I'm running 4.56 gears
w/33's... and she had a stuck mitsubishi 4 door deal buried up to the
underbody... Not from around here apparently cuz no one else was around
that area of the beach. I had to pull her out and across all this sand, and
I think she might have hit the brakes a time or two while doing it.

This jeep is my first manual transmission and I wasn't sure if I could get
more "grip" with the tranny with a higher performance clutch. A buddy has
had a ceramic one put in his mustang and says its a big difference, I'm just
not sure if it would be the same for a jeep? (TJ)

After reading all these posts, I suppose I'll pay a local shop to swap
tires... I wanted my rims on my jeep put on my gf's and I'm getting new
ones, so there'll be 10 rim/swaps going on, and I'm sure I'll want to get
another set of mudders for some special occasion sometime in the future.

I have seen where they fill the tire with ether and blow it up on the rim,
anyone have any luck with that?

Troy


"Earle Horton" <nurse--NOSPAM--busters@msn.com> wrote in message
news:1124654684.3caff463c37cb8703941f1e8eafa8892@t eranews...
> Things that might help your clutch are a winch, and regearing the axles.
> What gear ratio is it now? A clutch is not really designed to deliver
> power
> while slipping. Really, there are two legitimate positions for the clutch
> pedal, down and up.
>
> I have used toy tire changers before. They are not much fun.
>
> Earle
>
> "Troy" <troy@ .> wrote in message
> news:teGdnQZM-MTNSZXeRVn-uA@comcast.com...
>> When I have to someday replace my clutch in my TJ, are there any "heavy
>> duty" clutches I can get for it? Something that would grip a bit better
>> than stock? I noticed I can't pull vehicles too large outta sand without
>> burning my stock one up a bit.
>>
>>
>> Also, I've seen manual tire changers on the internet, are they worth a
> damn?
>> Or should I just buddy up with a tire shop here in town for swapping
>> tires
>> on rims? I saw this one: http://www.wikco.com/Tire.html
>>
>> Troy
>>
>>
>
>

 

Ya my first instinct was to winch it out but the last time the girl was
surrounded by about 25 yards of sugar sand all around, except for the ocean
part, where the tide was moving in on her heh heh. I'm running 4.56 gears
w/33's... and she had a stuck mitsubishi 4 door deal buried up to the
underbody... Not from around here apparently cuz no one else was around
that area of the beach. I had to pull her out and across all this sand, and
I think she might have hit the brakes a time or two while doing it.

This jeep is my first manual transmission and I wasn't sure if I could get
more "grip" with the tranny with a higher performance clutch. A buddy has
had a ceramic one put in his mustang and says its a big difference, I'm just
not sure if it would be the same for a jeep? (TJ)

After reading all these posts, I suppose I'll pay a local shop to swap
tires... I wanted my rims on my jeep put on my gf's and I'm getting new
ones, so there'll be 10 rim/swaps going on, and I'm sure I'll want to get
another set of mudders for some special occasion sometime in the future.

I have seen where they fill the tire with ether and blow it up on the rim,
anyone have any luck with that?

Troy


"Earle Horton" <nurse--NOSPAM--busters@msn.com> wrote in message
news:1124654684.3caff463c37cb8703941f1e8eafa8892@t eranews...
> Things that might help your clutch are a winch, and regearing the axles.
> What gear ratio is it now? A clutch is not really designed to deliver
> power
> while slipping. Really, there are two legitimate positions for the clutch
> pedal, down and up.
>
> I have used toy tire changers before. They are not much fun.
>
> Earle
>
> "Troy" <troy@ .> wrote in message
> news:teGdnQZM-MTNSZXeRVn-uA@comcast.com...
>> When I have to someday replace my clutch in my TJ, are there any "heavy
>> duty" clutches I can get for it? Something that would grip a bit better
>> than stock? I noticed I can't pull vehicles too large outta sand without
>> burning my stock one up a bit.
>>
>>
>> Also, I've seen manual tire changers on the internet, are they worth a
> damn?
>> Or should I just buddy up with a tire shop here in town for swapping
>> tires
>> on rims? I saw this one: http://www.wikco.com/Tire.html
>>
>> Troy
>>
>>
>
>

 

Ya my first instinct was to winch it out but the last time the girl was
surrounded by about 25 yards of sugar sand all around, except for the ocean
part, where the tide was moving in on her heh heh. I'm running 4.56 gears
w/33's... and she had a stuck mitsubishi 4 door deal buried up to the
underbody... Not from around here apparently cuz no one else was around
that area of the beach. I had to pull her out and across all this sand, and
I think she might have hit the brakes a time or two while doing it.

This jeep is my first manual transmission and I wasn't sure if I could get
more "grip" with the tranny with a higher performance clutch. A buddy has
had a ceramic one put in his mustang and says its a big difference, I'm just
not sure if it would be the same for a jeep? (TJ)

After reading all these posts, I suppose I'll pay a local shop to swap
tires... I wanted my rims on my jeep put on my gf's and I'm getting new
ones, so there'll be 10 rim/swaps going on, and I'm sure I'll want to get
another set of mudders for some special occasion sometime in the future.

I have seen where they fill the tire with ether and blow it up on the rim,
anyone have any luck with that?

Troy


"Earle Horton" <nurse--NOSPAM--busters@msn.com> wrote in message
news:1124654684.3caff463c37cb8703941f1e8eafa8892@t eranews...
> Things that might help your clutch are a winch, and regearing the axles.
> What gear ratio is it now? A clutch is not really designed to deliver
> power
> while slipping. Really, there are two legitimate positions for the clutch
> pedal, down and up.
>
> I have used toy tire changers before. They are not much fun.
>
> Earle
>
> "Troy" <troy@ .> wrote in message
> news:teGdnQZM-MTNSZXeRVn-uA@comcast.com...
>> When I have to someday replace my clutch in my TJ, are there any "heavy
>> duty" clutches I can get for it? Something that would grip a bit better
>> than stock? I noticed I can't pull vehicles too large outta sand without
>> burning my stock one up a bit.
>>
>>
>> Also, I've seen manual tire changers on the internet, are they worth a
> damn?
>> Or should I just buddy up with a tire shop here in town for swapping
>> tires
>> on rims? I saw this one: http://www.wikco.com/Tire.html
>>
>> Troy
>>
>>
>
>

 

Yeah I have that HF tool also;
http://www.harborfreight.com/cpi/cta...emnumber=34542
I also welded up some metal to make a sturdy base I can bolt it to so it is
truly "portable".
It works well enough for me and I have changed a couple of dozen tires with
it. So it has paid for itself esp. since I bought it on sale for $35. ;-)
BTW I usually use a towel to protect the wheels while I break the bead!

later,
dave AKA vwdoc1


"Will Honea" <whonea@yahoo.com> wrote in message
news:JxX2tWiP5BNp-pn2-zTRd8HdzeNOx@anon.none.net...
> Dad had a tire changer he got from Harbor Freight, of all places, out
> on the farm before he passed away 3 years ago. The particular one had
> was pretty handy - after he did a lot of welding to set up a decent
> base for it. Every other toy changer I've seen/used was more work to
> use than a BMFH and a decent set of irons. Well worth a few bucks
> just in the time you save by having a decently equipped shop do the
> dirty work IMNSHO.

 

Yeah I have that HF tool also;
http://www.harborfreight.com/cpi/cta...emnumber=34542
I also welded up some metal to make a sturdy base I can bolt it to so it is
truly "portable".
It works well enough for me and I have changed a couple of dozen tires with
it. So it has paid for itself esp. since I bought it on sale for $35. ;-)
BTW I usually use a towel to protect the wheels while I break the bead!

later,
dave AKA vwdoc1


"Will Honea" <whonea@yahoo.com> wrote in message
news:JxX2tWiP5BNp-pn2-zTRd8HdzeNOx@anon.none.net...
> Dad had a tire changer he got from Harbor Freight, of all places, out
> on the farm before he passed away 3 years ago. The particular one had
> was pretty handy - after he did a lot of welding to set up a decent
> base for it. Every other toy changer I've seen/used was more work to
> use than a BMFH and a decent set of irons. Well worth a few bucks
> just in the time you save by having a decently equipped shop do the
> dirty work IMNSHO.

 

Yeah I have that HF tool also;
http://www.harborfreight.com/cpi/cta...emnumber=34542
I also welded up some metal to make a sturdy base I can bolt it to so it is
truly "portable".
It works well enough for me and I have changed a couple of dozen tires with
it. So it has paid for itself esp. since I bought it on sale for $35. ;-)
BTW I usually use a towel to protect the wheels while I break the bead!

later,
dave AKA vwdoc1


"Will Honea" <whonea@yahoo.com> wrote in message
news:JxX2tWiP5BNp-pn2-zTRd8HdzeNOx@anon.none.net...
> Dad had a tire changer he got from Harbor Freight, of all places, out
> on the farm before he passed away 3 years ago. The particular one had
> was pretty handy - after he did a lot of welding to set up a decent
> base for it. Every other toy changer I've seen/used was more work to
> use than a BMFH and a decent set of irons. Well worth a few bucks
> just in the time you save by having a decently equipped shop do the
> dirty work IMNSHO.

 

Yeah I have that HF tool also;
http://www.harborfreight.com/cpi/cta...emnumber=34542
I also welded up some metal to make a sturdy base I can bolt it to so it is
truly "portable".
It works well enough for me and I have changed a couple of dozen tires with
it. So it has paid for itself esp. since I bought it on sale for $35. ;-)
BTW I usually use a towel to protect the wheels while I break the bead!

later,
dave AKA vwdoc1


"Will Honea" <whonea@yahoo.com> wrote in message
news:JxX2tWiP5BNp-pn2-zTRd8HdzeNOx@anon.none.net...
> Dad had a tire changer he got from Harbor Freight, of all places, out
> on the farm before he passed away 3 years ago. The particular one had
> was pretty handy - after he did a lot of welding to set up a decent
> base for it. Every other toy changer I've seen/used was more work to
> use than a BMFH and a decent set of irons. Well worth a few bucks
> just in the time you save by having a decently equipped shop do the
> dirty work IMNSHO.

 

Well there should be some links floating around about the 'Darwin
Award' wanna be's playing with ether and tires. Usually after a few
beer too...

You wrap a strap around the center of the tire and either winch it up
or use the tire iron and twist it up like a tourniquet. This pulls in
the center and pushes out the bead to the rim.

Manually changing an off road large tire sucks the big one!

You should be thinking about a centerforce clutch for pulls like that.
The higher the rpm you hit it at, the harder it grabs.

Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's