CJ7 Steering upgrades
Guest
Posts: n/a
Re: CJ7 Steering upgrades
Mike,
I have a 1983 CJ7 and I hvae 35 Super Swampers on it. I replaced the
sterring colum with one that has U-joints at both ends to help with the
articulation. That helped some but the main thing I did to FIX the same
problem you are having is I replaced the DRAG LINK. Hope this helps....
Mike Romain wrote:
> For starts, it isn't likely you are going to get a solid steering
> response from a lifted CJ7 at high speed..... Even with all new front
> end parts they get white knuckle around 75 mph....
>
> Mine was what I considered not safe at 65 mph when i got it but all the
> components tested 'safe' with some wear. Add up all the wear and it was
> down right nasty...
>
> One quick place to check for too much wear is the column right by the
> firewall. There is a u-joint there. If that is sloppy, it causes a
> 'lot' of steering wheel play. There is a company here in Toronto Canada
> that rebuilds them with grease fittings. You have another slop point
> just before the box on the column. There is a fitting there that can
> get sloppy.
>
> It is unlikely you need to touch the box, but if you do need to adjust
> it you do so at the adjuster plug where the column enters. The big lock
> nut/ring has to be loosened and a special tool used to tighten the plug
> all the way in. It then needs to back off 1/8" and the lock ring
> tightened. You don't touch the gear preset bolt on top of the box
> unless you have it on the bench for a rebuild. If you want to do that I
> have the directions on .pdf I can send.
>
> Then you need to go under and have someone cut the steering from pin out
> to pin out to see if you can spot slop in any joints. Worn ones are
> usually visable for play.
>
> You then can jack up the front and wiggle the wheels. If they have
> play, your wheel bearings need attention. The play will have the rotor
> moving. That will really play hell with the steering.
>
> A few things for you...
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> (More Off Road album links at bottom of the view page)
>
> Steve wrote:
> >
> > I own a 86 CJ7 with an inline 6, 32" wheels with a 4" lift and having
> > scary steering issues running at highway speeds. I have stock parts
> > with power steering and need to fix this issue asap. What do I need to
> > upgrade or replace to create a solid steering response at higer speeds.
> > Way to much play in my steering. Do I need a new pump, gearbox, shaft?
> >
> > Thanks for the advice..
> >
> > Steve
I have a 1983 CJ7 and I hvae 35 Super Swampers on it. I replaced the
sterring colum with one that has U-joints at both ends to help with the
articulation. That helped some but the main thing I did to FIX the same
problem you are having is I replaced the DRAG LINK. Hope this helps....
Mike Romain wrote:
> For starts, it isn't likely you are going to get a solid steering
> response from a lifted CJ7 at high speed..... Even with all new front
> end parts they get white knuckle around 75 mph....
>
> Mine was what I considered not safe at 65 mph when i got it but all the
> components tested 'safe' with some wear. Add up all the wear and it was
> down right nasty...
>
> One quick place to check for too much wear is the column right by the
> firewall. There is a u-joint there. If that is sloppy, it causes a
> 'lot' of steering wheel play. There is a company here in Toronto Canada
> that rebuilds them with grease fittings. You have another slop point
> just before the box on the column. There is a fitting there that can
> get sloppy.
>
> It is unlikely you need to touch the box, but if you do need to adjust
> it you do so at the adjuster plug where the column enters. The big lock
> nut/ring has to be loosened and a special tool used to tighten the plug
> all the way in. It then needs to back off 1/8" and the lock ring
> tightened. You don't touch the gear preset bolt on top of the box
> unless you have it on the bench for a rebuild. If you want to do that I
> have the directions on .pdf I can send.
>
> Then you need to go under and have someone cut the steering from pin out
> to pin out to see if you can spot slop in any joints. Worn ones are
> usually visable for play.
>
> You then can jack up the front and wiggle the wheels. If they have
> play, your wheel bearings need attention. The play will have the rotor
> moving. That will really play hell with the steering.
>
> A few things for you...
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> (More Off Road album links at bottom of the view page)
>
> Steve wrote:
> >
> > I own a 86 CJ7 with an inline 6, 32" wheels with a 4" lift and having
> > scary steering issues running at highway speeds. I have stock parts
> > with power steering and need to fix this issue asap. What do I need to
> > upgrade or replace to create a solid steering response at higer speeds.
> > Way to much play in my steering. Do I need a new pump, gearbox, shaft?
> >
> > Thanks for the advice..
> >
> > Steve
Guest
Posts: n/a
Re: CJ7 Steering upgrades
Mike,
I have a 1983 CJ7 and I hvae 35 Super Swampers on it. I replaced the
sterring colum with one that has U-joints at both ends to help with the
articulation. That helped some but the main thing I did to FIX the same
problem you are having is I replaced the DRAG LINK. Hope this helps....
Mike Romain wrote:
> For starts, it isn't likely you are going to get a solid steering
> response from a lifted CJ7 at high speed..... Even with all new front
> end parts they get white knuckle around 75 mph....
>
> Mine was what I considered not safe at 65 mph when i got it but all the
> components tested 'safe' with some wear. Add up all the wear and it was
> down right nasty...
>
> One quick place to check for too much wear is the column right by the
> firewall. There is a u-joint there. If that is sloppy, it causes a
> 'lot' of steering wheel play. There is a company here in Toronto Canada
> that rebuilds them with grease fittings. You have another slop point
> just before the box on the column. There is a fitting there that can
> get sloppy.
>
> It is unlikely you need to touch the box, but if you do need to adjust
> it you do so at the adjuster plug where the column enters. The big lock
> nut/ring has to be loosened and a special tool used to tighten the plug
> all the way in. It then needs to back off 1/8" and the lock ring
> tightened. You don't touch the gear preset bolt on top of the box
> unless you have it on the bench for a rebuild. If you want to do that I
> have the directions on .pdf I can send.
>
> Then you need to go under and have someone cut the steering from pin out
> to pin out to see if you can spot slop in any joints. Worn ones are
> usually visable for play.
>
> You then can jack up the front and wiggle the wheels. If they have
> play, your wheel bearings need attention. The play will have the rotor
> moving. That will really play hell with the steering.
>
> A few things for you...
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> (More Off Road album links at bottom of the view page)
>
> Steve wrote:
> >
> > I own a 86 CJ7 with an inline 6, 32" wheels with a 4" lift and having
> > scary steering issues running at highway speeds. I have stock parts
> > with power steering and need to fix this issue asap. What do I need to
> > upgrade or replace to create a solid steering response at higer speeds.
> > Way to much play in my steering. Do I need a new pump, gearbox, shaft?
> >
> > Thanks for the advice..
> >
> > Steve
I have a 1983 CJ7 and I hvae 35 Super Swampers on it. I replaced the
sterring colum with one that has U-joints at both ends to help with the
articulation. That helped some but the main thing I did to FIX the same
problem you are having is I replaced the DRAG LINK. Hope this helps....
Mike Romain wrote:
> For starts, it isn't likely you are going to get a solid steering
> response from a lifted CJ7 at high speed..... Even with all new front
> end parts they get white knuckle around 75 mph....
>
> Mine was what I considered not safe at 65 mph when i got it but all the
> components tested 'safe' with some wear. Add up all the wear and it was
> down right nasty...
>
> One quick place to check for too much wear is the column right by the
> firewall. There is a u-joint there. If that is sloppy, it causes a
> 'lot' of steering wheel play. There is a company here in Toronto Canada
> that rebuilds them with grease fittings. You have another slop point
> just before the box on the column. There is a fitting there that can
> get sloppy.
>
> It is unlikely you need to touch the box, but if you do need to adjust
> it you do so at the adjuster plug where the column enters. The big lock
> nut/ring has to be loosened and a special tool used to tighten the plug
> all the way in. It then needs to back off 1/8" and the lock ring
> tightened. You don't touch the gear preset bolt on top of the box
> unless you have it on the bench for a rebuild. If you want to do that I
> have the directions on .pdf I can send.
>
> Then you need to go under and have someone cut the steering from pin out
> to pin out to see if you can spot slop in any joints. Worn ones are
> usually visable for play.
>
> You then can jack up the front and wiggle the wheels. If they have
> play, your wheel bearings need attention. The play will have the rotor
> moving. That will really play hell with the steering.
>
> A few things for you...
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> (More Off Road album links at bottom of the view page)
>
> Steve wrote:
> >
> > I own a 86 CJ7 with an inline 6, 32" wheels with a 4" lift and having
> > scary steering issues running at highway speeds. I have stock parts
> > with power steering and need to fix this issue asap. What do I need to
> > upgrade or replace to create a solid steering response at higer speeds.
> > Way to much play in my steering. Do I need a new pump, gearbox, shaft?
> >
> > Thanks for the advice..
> >
> > Steve
Guest
Posts: n/a
Re: CJ7 Steering upgrades
Mike,
I have a 1983 CJ7 and I hvae 35 Super Swampers on it. I replaced the
sterring colum with one that has U-joints at both ends to help with the
articulation. That helped some but the main thing I did to FIX the same
problem you are having is I replaced the DRAG LINK. Hope this helps....
Mike Romain wrote:
> For starts, it isn't likely you are going to get a solid steering
> response from a lifted CJ7 at high speed..... Even with all new front
> end parts they get white knuckle around 75 mph....
>
> Mine was what I considered not safe at 65 mph when i got it but all the
> components tested 'safe' with some wear. Add up all the wear and it was
> down right nasty...
>
> One quick place to check for too much wear is the column right by the
> firewall. There is a u-joint there. If that is sloppy, it causes a
> 'lot' of steering wheel play. There is a company here in Toronto Canada
> that rebuilds them with grease fittings. You have another slop point
> just before the box on the column. There is a fitting there that can
> get sloppy.
>
> It is unlikely you need to touch the box, but if you do need to adjust
> it you do so at the adjuster plug where the column enters. The big lock
> nut/ring has to be loosened and a special tool used to tighten the plug
> all the way in. It then needs to back off 1/8" and the lock ring
> tightened. You don't touch the gear preset bolt on top of the box
> unless you have it on the bench for a rebuild. If you want to do that I
> have the directions on .pdf I can send.
>
> Then you need to go under and have someone cut the steering from pin out
> to pin out to see if you can spot slop in any joints. Worn ones are
> usually visable for play.
>
> You then can jack up the front and wiggle the wheels. If they have
> play, your wheel bearings need attention. The play will have the rotor
> moving. That will really play hell with the steering.
>
> A few things for you...
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> (More Off Road album links at bottom of the view page)
>
> Steve wrote:
> >
> > I own a 86 CJ7 with an inline 6, 32" wheels with a 4" lift and having
> > scary steering issues running at highway speeds. I have stock parts
> > with power steering and need to fix this issue asap. What do I need to
> > upgrade or replace to create a solid steering response at higer speeds.
> > Way to much play in my steering. Do I need a new pump, gearbox, shaft?
> >
> > Thanks for the advice..
> >
> > Steve
I have a 1983 CJ7 and I hvae 35 Super Swampers on it. I replaced the
sterring colum with one that has U-joints at both ends to help with the
articulation. That helped some but the main thing I did to FIX the same
problem you are having is I replaced the DRAG LINK. Hope this helps....
Mike Romain wrote:
> For starts, it isn't likely you are going to get a solid steering
> response from a lifted CJ7 at high speed..... Even with all new front
> end parts they get white knuckle around 75 mph....
>
> Mine was what I considered not safe at 65 mph when i got it but all the
> components tested 'safe' with some wear. Add up all the wear and it was
> down right nasty...
>
> One quick place to check for too much wear is the column right by the
> firewall. There is a u-joint there. If that is sloppy, it causes a
> 'lot' of steering wheel play. There is a company here in Toronto Canada
> that rebuilds them with grease fittings. You have another slop point
> just before the box on the column. There is a fitting there that can
> get sloppy.
>
> It is unlikely you need to touch the box, but if you do need to adjust
> it you do so at the adjuster plug where the column enters. The big lock
> nut/ring has to be loosened and a special tool used to tighten the plug
> all the way in. It then needs to back off 1/8" and the lock ring
> tightened. You don't touch the gear preset bolt on top of the box
> unless you have it on the bench for a rebuild. If you want to do that I
> have the directions on .pdf I can send.
>
> Then you need to go under and have someone cut the steering from pin out
> to pin out to see if you can spot slop in any joints. Worn ones are
> usually visable for play.
>
> You then can jack up the front and wiggle the wheels. If they have
> play, your wheel bearings need attention. The play will have the rotor
> moving. That will really play hell with the steering.
>
> A few things for you...
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> (More Off Road album links at bottom of the view page)
>
> Steve wrote:
> >
> > I own a 86 CJ7 with an inline 6, 32" wheels with a 4" lift and having
> > scary steering issues running at highway speeds. I have stock parts
> > with power steering and need to fix this issue asap. What do I need to
> > upgrade or replace to create a solid steering response at higer speeds.
> > Way to much play in my steering. Do I need a new pump, gearbox, shaft?
> >
> > Thanks for the advice..
> >
> > Steve
Guest
Posts: n/a
Re: CJ7 Steering upgrades
I did the long arm on my drag link and went out the next week and bent
the sucker. It did set my steering straight after my lift though. LOL!
My steering is messed, but mine is a bad ball joint. I am not the OP.
Mike
rousch6 wrote:
>
> Mike,
> I have a 1983 CJ7 and I hvae 35 Super Swampers on it. I replaced the
> sterring colum with one that has U-joints at both ends to help with the
> articulation. That helped some but the main thing I did to FIX the same
> problem you are having is I replaced the DRAG LINK. Hope this helps....
>
> Mike Romain wrote:
> > For starts, it isn't likely you are going to get a solid steering
> > response from a lifted CJ7 at high speed..... Even with all new front
> > end parts they get white knuckle around 75 mph....
> >
> > Mine was what I considered not safe at 65 mph when i got it but all the
> > components tested 'safe' with some wear. Add up all the wear and it was
> > down right nasty...
> >
> > One quick place to check for too much wear is the column right by the
> > firewall. There is a u-joint there. If that is sloppy, it causes a
> > 'lot' of steering wheel play. There is a company here in Toronto Canada
> > that rebuilds them with grease fittings. You have another slop point
> > just before the box on the column. There is a fitting there that can
> > get sloppy.
> >
> > It is unlikely you need to touch the box, but if you do need to adjust
> > it you do so at the adjuster plug where the column enters. The big lock
> > nut/ring has to be loosened and a special tool used to tighten the plug
> > all the way in. It then needs to back off 1/8" and the lock ring
> > tightened. You don't touch the gear preset bolt on top of the box
> > unless you have it on the bench for a rebuild. If you want to do that I
> > have the directions on .pdf I can send.
> >
> > Then you need to go under and have someone cut the steering from pin out
> > to pin out to see if you can spot slop in any joints. Worn ones are
> > usually visable for play.
> >
> > You then can jack up the front and wiggle the wheels. If they have
> > play, your wheel bearings need attention. The play will have the rotor
> > moving. That will really play hell with the steering.
> >
> > A few things for you...
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> > Canadian Off Road Trips Photos: Non members can still view!
> > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> > (More Off Road album links at bottom of the view page)
> >
> > Steve wrote:
> > >
> > > I own a 86 CJ7 with an inline 6, 32" wheels with a 4" lift and having
> > > scary steering issues running at highway speeds. I have stock parts
> > > with power steering and need to fix this issue asap. What do I need to
> > > upgrade or replace to create a solid steering response at higer speeds.
> > > Way to much play in my steering. Do I need a new pump, gearbox, shaft?
> > >
> > > Thanks for the advice..
> > >
> > > Steve
the sucker. It did set my steering straight after my lift though. LOL!
My steering is messed, but mine is a bad ball joint. I am not the OP.
Mike
rousch6 wrote:
>
> Mike,
> I have a 1983 CJ7 and I hvae 35 Super Swampers on it. I replaced the
> sterring colum with one that has U-joints at both ends to help with the
> articulation. That helped some but the main thing I did to FIX the same
> problem you are having is I replaced the DRAG LINK. Hope this helps....
>
> Mike Romain wrote:
> > For starts, it isn't likely you are going to get a solid steering
> > response from a lifted CJ7 at high speed..... Even with all new front
> > end parts they get white knuckle around 75 mph....
> >
> > Mine was what I considered not safe at 65 mph when i got it but all the
> > components tested 'safe' with some wear. Add up all the wear and it was
> > down right nasty...
> >
> > One quick place to check for too much wear is the column right by the
> > firewall. There is a u-joint there. If that is sloppy, it causes a
> > 'lot' of steering wheel play. There is a company here in Toronto Canada
> > that rebuilds them with grease fittings. You have another slop point
> > just before the box on the column. There is a fitting there that can
> > get sloppy.
> >
> > It is unlikely you need to touch the box, but if you do need to adjust
> > it you do so at the adjuster plug where the column enters. The big lock
> > nut/ring has to be loosened and a special tool used to tighten the plug
> > all the way in. It then needs to back off 1/8" and the lock ring
> > tightened. You don't touch the gear preset bolt on top of the box
> > unless you have it on the bench for a rebuild. If you want to do that I
> > have the directions on .pdf I can send.
> >
> > Then you need to go under and have someone cut the steering from pin out
> > to pin out to see if you can spot slop in any joints. Worn ones are
> > usually visable for play.
> >
> > You then can jack up the front and wiggle the wheels. If they have
> > play, your wheel bearings need attention. The play will have the rotor
> > moving. That will really play hell with the steering.
> >
> > A few things for you...
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> > Canadian Off Road Trips Photos: Non members can still view!
> > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> > (More Off Road album links at bottom of the view page)
> >
> > Steve wrote:
> > >
> > > I own a 86 CJ7 with an inline 6, 32" wheels with a 4" lift and having
> > > scary steering issues running at highway speeds. I have stock parts
> > > with power steering and need to fix this issue asap. What do I need to
> > > upgrade or replace to create a solid steering response at higer speeds.
> > > Way to much play in my steering. Do I need a new pump, gearbox, shaft?
> > >
> > > Thanks for the advice..
> > >
> > > Steve
Guest
Posts: n/a
Re: CJ7 Steering upgrades
I did the long arm on my drag link and went out the next week and bent
the sucker. It did set my steering straight after my lift though. LOL!
My steering is messed, but mine is a bad ball joint. I am not the OP.
Mike
rousch6 wrote:
>
> Mike,
> I have a 1983 CJ7 and I hvae 35 Super Swampers on it. I replaced the
> sterring colum with one that has U-joints at both ends to help with the
> articulation. That helped some but the main thing I did to FIX the same
> problem you are having is I replaced the DRAG LINK. Hope this helps....
>
> Mike Romain wrote:
> > For starts, it isn't likely you are going to get a solid steering
> > response from a lifted CJ7 at high speed..... Even with all new front
> > end parts they get white knuckle around 75 mph....
> >
> > Mine was what I considered not safe at 65 mph when i got it but all the
> > components tested 'safe' with some wear. Add up all the wear and it was
> > down right nasty...
> >
> > One quick place to check for too much wear is the column right by the
> > firewall. There is a u-joint there. If that is sloppy, it causes a
> > 'lot' of steering wheel play. There is a company here in Toronto Canada
> > that rebuilds them with grease fittings. You have another slop point
> > just before the box on the column. There is a fitting there that can
> > get sloppy.
> >
> > It is unlikely you need to touch the box, but if you do need to adjust
> > it you do so at the adjuster plug where the column enters. The big lock
> > nut/ring has to be loosened and a special tool used to tighten the plug
> > all the way in. It then needs to back off 1/8" and the lock ring
> > tightened. You don't touch the gear preset bolt on top of the box
> > unless you have it on the bench for a rebuild. If you want to do that I
> > have the directions on .pdf I can send.
> >
> > Then you need to go under and have someone cut the steering from pin out
> > to pin out to see if you can spot slop in any joints. Worn ones are
> > usually visable for play.
> >
> > You then can jack up the front and wiggle the wheels. If they have
> > play, your wheel bearings need attention. The play will have the rotor
> > moving. That will really play hell with the steering.
> >
> > A few things for you...
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> > Canadian Off Road Trips Photos: Non members can still view!
> > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> > (More Off Road album links at bottom of the view page)
> >
> > Steve wrote:
> > >
> > > I own a 86 CJ7 with an inline 6, 32" wheels with a 4" lift and having
> > > scary steering issues running at highway speeds. I have stock parts
> > > with power steering and need to fix this issue asap. What do I need to
> > > upgrade or replace to create a solid steering response at higer speeds.
> > > Way to much play in my steering. Do I need a new pump, gearbox, shaft?
> > >
> > > Thanks for the advice..
> > >
> > > Steve
the sucker. It did set my steering straight after my lift though. LOL!
My steering is messed, but mine is a bad ball joint. I am not the OP.
Mike
rousch6 wrote:
>
> Mike,
> I have a 1983 CJ7 and I hvae 35 Super Swampers on it. I replaced the
> sterring colum with one that has U-joints at both ends to help with the
> articulation. That helped some but the main thing I did to FIX the same
> problem you are having is I replaced the DRAG LINK. Hope this helps....
>
> Mike Romain wrote:
> > For starts, it isn't likely you are going to get a solid steering
> > response from a lifted CJ7 at high speed..... Even with all new front
> > end parts they get white knuckle around 75 mph....
> >
> > Mine was what I considered not safe at 65 mph when i got it but all the
> > components tested 'safe' with some wear. Add up all the wear and it was
> > down right nasty...
> >
> > One quick place to check for too much wear is the column right by the
> > firewall. There is a u-joint there. If that is sloppy, it causes a
> > 'lot' of steering wheel play. There is a company here in Toronto Canada
> > that rebuilds them with grease fittings. You have another slop point
> > just before the box on the column. There is a fitting there that can
> > get sloppy.
> >
> > It is unlikely you need to touch the box, but if you do need to adjust
> > it you do so at the adjuster plug where the column enters. The big lock
> > nut/ring has to be loosened and a special tool used to tighten the plug
> > all the way in. It then needs to back off 1/8" and the lock ring
> > tightened. You don't touch the gear preset bolt on top of the box
> > unless you have it on the bench for a rebuild. If you want to do that I
> > have the directions on .pdf I can send.
> >
> > Then you need to go under and have someone cut the steering from pin out
> > to pin out to see if you can spot slop in any joints. Worn ones are
> > usually visable for play.
> >
> > You then can jack up the front and wiggle the wheels. If they have
> > play, your wheel bearings need attention. The play will have the rotor
> > moving. That will really play hell with the steering.
> >
> > A few things for you...
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> > Canadian Off Road Trips Photos: Non members can still view!
> > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> > (More Off Road album links at bottom of the view page)
> >
> > Steve wrote:
> > >
> > > I own a 86 CJ7 with an inline 6, 32" wheels with a 4" lift and having
> > > scary steering issues running at highway speeds. I have stock parts
> > > with power steering and need to fix this issue asap. What do I need to
> > > upgrade or replace to create a solid steering response at higer speeds.
> > > Way to much play in my steering. Do I need a new pump, gearbox, shaft?
> > >
> > > Thanks for the advice..
> > >
> > > Steve
Guest
Posts: n/a
Re: CJ7 Steering upgrades
I did the long arm on my drag link and went out the next week and bent
the sucker. It did set my steering straight after my lift though. LOL!
My steering is messed, but mine is a bad ball joint. I am not the OP.
Mike
rousch6 wrote:
>
> Mike,
> I have a 1983 CJ7 and I hvae 35 Super Swampers on it. I replaced the
> sterring colum with one that has U-joints at both ends to help with the
> articulation. That helped some but the main thing I did to FIX the same
> problem you are having is I replaced the DRAG LINK. Hope this helps....
>
> Mike Romain wrote:
> > For starts, it isn't likely you are going to get a solid steering
> > response from a lifted CJ7 at high speed..... Even with all new front
> > end parts they get white knuckle around 75 mph....
> >
> > Mine was what I considered not safe at 65 mph when i got it but all the
> > components tested 'safe' with some wear. Add up all the wear and it was
> > down right nasty...
> >
> > One quick place to check for too much wear is the column right by the
> > firewall. There is a u-joint there. If that is sloppy, it causes a
> > 'lot' of steering wheel play. There is a company here in Toronto Canada
> > that rebuilds them with grease fittings. You have another slop point
> > just before the box on the column. There is a fitting there that can
> > get sloppy.
> >
> > It is unlikely you need to touch the box, but if you do need to adjust
> > it you do so at the adjuster plug where the column enters. The big lock
> > nut/ring has to be loosened and a special tool used to tighten the plug
> > all the way in. It then needs to back off 1/8" and the lock ring
> > tightened. You don't touch the gear preset bolt on top of the box
> > unless you have it on the bench for a rebuild. If you want to do that I
> > have the directions on .pdf I can send.
> >
> > Then you need to go under and have someone cut the steering from pin out
> > to pin out to see if you can spot slop in any joints. Worn ones are
> > usually visable for play.
> >
> > You then can jack up the front and wiggle the wheels. If they have
> > play, your wheel bearings need attention. The play will have the rotor
> > moving. That will really play hell with the steering.
> >
> > A few things for you...
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> > Canadian Off Road Trips Photos: Non members can still view!
> > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> > (More Off Road album links at bottom of the view page)
> >
> > Steve wrote:
> > >
> > > I own a 86 CJ7 with an inline 6, 32" wheels with a 4" lift and having
> > > scary steering issues running at highway speeds. I have stock parts
> > > with power steering and need to fix this issue asap. What do I need to
> > > upgrade or replace to create a solid steering response at higer speeds.
> > > Way to much play in my steering. Do I need a new pump, gearbox, shaft?
> > >
> > > Thanks for the advice..
> > >
> > > Steve
the sucker. It did set my steering straight after my lift though. LOL!
My steering is messed, but mine is a bad ball joint. I am not the OP.
Mike
rousch6 wrote:
>
> Mike,
> I have a 1983 CJ7 and I hvae 35 Super Swampers on it. I replaced the
> sterring colum with one that has U-joints at both ends to help with the
> articulation. That helped some but the main thing I did to FIX the same
> problem you are having is I replaced the DRAG LINK. Hope this helps....
>
> Mike Romain wrote:
> > For starts, it isn't likely you are going to get a solid steering
> > response from a lifted CJ7 at high speed..... Even with all new front
> > end parts they get white knuckle around 75 mph....
> >
> > Mine was what I considered not safe at 65 mph when i got it but all the
> > components tested 'safe' with some wear. Add up all the wear and it was
> > down right nasty...
> >
> > One quick place to check for too much wear is the column right by the
> > firewall. There is a u-joint there. If that is sloppy, it causes a
> > 'lot' of steering wheel play. There is a company here in Toronto Canada
> > that rebuilds them with grease fittings. You have another slop point
> > just before the box on the column. There is a fitting there that can
> > get sloppy.
> >
> > It is unlikely you need to touch the box, but if you do need to adjust
> > it you do so at the adjuster plug where the column enters. The big lock
> > nut/ring has to be loosened and a special tool used to tighten the plug
> > all the way in. It then needs to back off 1/8" and the lock ring
> > tightened. You don't touch the gear preset bolt on top of the box
> > unless you have it on the bench for a rebuild. If you want to do that I
> > have the directions on .pdf I can send.
> >
> > Then you need to go under and have someone cut the steering from pin out
> > to pin out to see if you can spot slop in any joints. Worn ones are
> > usually visable for play.
> >
> > You then can jack up the front and wiggle the wheels. If they have
> > play, your wheel bearings need attention. The play will have the rotor
> > moving. That will really play hell with the steering.
> >
> > A few things for you...
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> > Canadian Off Road Trips Photos: Non members can still view!
> > Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> > (More Off Road album links at bottom of the view page)
> >
> > Steve wrote:
> > >
> > > I own a 86 CJ7 with an inline 6, 32" wheels with a 4" lift and having
> > > scary steering issues running at highway speeds. I have stock parts
> > > with power steering and need to fix this issue asap. What do I need to
> > > upgrade or replace to create a solid steering response at higer speeds.
> > > Way to much play in my steering. Do I need a new pump, gearbox, shaft?
> > >
> > > Thanks for the advice..
> > >
> > > Steve
Thread
Thread Starter
Forum
Replies
Last Post
Mike Romain
Jeep Mailing List
8
Jul 26, 2007 06:43 PM
Jeff DeWitt
Jeep Mailing List
0
Apr 19, 2006 08:46 PM
Goat Crapp
Jeep Mailing List
16
Aug 10, 2004 06:46 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)