Cj5/151 with Rochester SE2. Need Vacuum Hose Diagram
02-20-2007, 11:28 AM
#11
Guest
Posts: n/a
Re: Cj5/151 with Rochester SE2. Need Vacuum Hose Diagram
Mike: I have the Haynes manual (CJ'49-'86) and could find nothing in it.
What page?
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:45db14f9$0$2631$9a6e19ea@unlimited.newshostin g.com...
> Too bad you don't live close to Toronto, I am pretty good at figuring out
> where vacuum lines should go to.
>
> I was just looking in the Haynes CJ manual, and it does cover just about
> all of your vacuum line plumbing routing and components for the feedback
> carb's operation. It is not an expensive book and most auto stores sell
> it. Unfortunately my book is broken right at the 151 emissions section
> and is missing a few pages. I still see most of the system's setup.
>
> If you are running the full emissions package, the lines route differently
> than if you just need functioning main items.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> (More Off Road album links at bottom of the view page)
>
> MStevens003 wrote:
>> I've ben to the references here that are still live (Tom Collin's site is
>> no more) and while I have found a couple of hints for individual
>> components I am still unsure of what to do. I have found nothing that is
>> specifically for the 4cyl 151 engine with the 2SE so if anyone knows of
>> links to vacuum diagrams please post.
>>
>> Thanks Bill for what you have given I'll make the best of it until I get
>> more info. Who else here has the 151 4cyl engine? Does anyone?
>> Michael
>>
>> "L.W. (Bill) ------ III" <----------@***.net> wrote in message
>> news:45da3b47$0$16362$88260bb3@free.teranews.com.. .
>>> The one going to the choke pull-off, will be full manifold vacuum.
>>> Others is be going to devices much like the six cylinder:
>>> http://www.jedi.com/obiwan/jeep/misc/vacuumhoses.html And newer YJ:
>>> http://home.sprynet.com/~dale02/list.htm
>>> God Bless America, Bill 0|||||||0
>>> mailto:-------------------- http://www.----------.com/
>>>
>>> "MStevens003" <MSTEVENS003@dc.rr.com> wrote in message
>>> news:45da18c8$0$27081$4c368faf@roadrunner.com...
>>>> Just rebuilt the Rochester SE2 carb on my '81 CJ5. It's the 151 engine
>>>> commonly known as the "four banger". The bore is I have 5 hanging
>>>> vacuum
>>>> hoses and 7 tubes looking for hoses and no idea what goes where as all
>>>> my
>>>> marking have rubbed off. There is a vacuum hose routing diagram under
>>>> the
>>>> hood but it shows afr fewer hoses that I have hanging around and does
>>>> not
>>>> help me.
>>>>
>>>> Can someone please point me to a routing diagram? In case someone knows
>>> the
>>>> answer to this or has a simila Jeep I will list here what pipes looking
>>> for
>>>> hoses I have.
>>>>
>>>> One pipe on the choke solenoid
>>>> Three pipes on the plenum that feed straight into the the intake
>>>> manifold
>>>> just inder the carb and
>>>> Two tubes sticking out of the middle section of the carb body
>>>> One from the bottom section of the carb.
>>>>
>>>> Hope someone can help.
>>>>
>>>> Thanks
>>>>
>>>> Michael
>>>>
>>>>
>>>
>>>
>>> --
>>> Posted via a free Usenet account from http://www.teranews.com
>>>
>>
What page?
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:45db14f9$0$2631$9a6e19ea@unlimited.newshostin g.com...
> Too bad you don't live close to Toronto, I am pretty good at figuring out
> where vacuum lines should go to.
>
> I was just looking in the Haynes CJ manual, and it does cover just about
> all of your vacuum line plumbing routing and components for the feedback
> carb's operation. It is not an expensive book and most auto stores sell
> it. Unfortunately my book is broken right at the 151 emissions section
> and is missing a few pages. I still see most of the system's setup.
>
> If you are running the full emissions package, the lines route differently
> than if you just need functioning main items.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> (More Off Road album links at bottom of the view page)
>
> MStevens003 wrote:
>> I've ben to the references here that are still live (Tom Collin's site is
>> no more) and while I have found a couple of hints for individual
>> components I am still unsure of what to do. I have found nothing that is
>> specifically for the 4cyl 151 engine with the 2SE so if anyone knows of
>> links to vacuum diagrams please post.
>>
>> Thanks Bill for what you have given I'll make the best of it until I get
>> more info. Who else here has the 151 4cyl engine? Does anyone?
>> Michael
>>
>> "L.W. (Bill) ------ III" <----------@***.net> wrote in message
>> news:45da3b47$0$16362$88260bb3@free.teranews.com.. .
>>> The one going to the choke pull-off, will be full manifold vacuum.
>>> Others is be going to devices much like the six cylinder:
>>> http://www.jedi.com/obiwan/jeep/misc/vacuumhoses.html And newer YJ:
>>> http://home.sprynet.com/~dale02/list.htm
>>> God Bless America, Bill 0|||||||0
>>> mailto:-------------------- http://www.----------.com/
>>>
>>> "MStevens003" <MSTEVENS003@dc.rr.com> wrote in message
>>> news:45da18c8$0$27081$4c368faf@roadrunner.com...
>>>> Just rebuilt the Rochester SE2 carb on my '81 CJ5. It's the 151 engine
>>>> commonly known as the "four banger". The bore is I have 5 hanging
>>>> vacuum
>>>> hoses and 7 tubes looking for hoses and no idea what goes where as all
>>>> my
>>>> marking have rubbed off. There is a vacuum hose routing diagram under
>>>> the
>>>> hood but it shows afr fewer hoses that I have hanging around and does
>>>> not
>>>> help me.
>>>>
>>>> Can someone please point me to a routing diagram? In case someone knows
>>> the
>>>> answer to this or has a simila Jeep I will list here what pipes looking
>>> for
>>>> hoses I have.
>>>>
>>>> One pipe on the choke solenoid
>>>> Three pipes on the plenum that feed straight into the the intake
>>>> manifold
>>>> just inder the carb and
>>>> Two tubes sticking out of the middle section of the carb body
>>>> One from the bottom section of the carb.
>>>>
>>>> Hope someone can help.
>>>>
>>>> Thanks
>>>>
>>>> Michael
>>>>
>>>>
>>>
>>>
>>> --
>>> Posted via a free Usenet account from http://www.teranews.com
>>>
>>
02-20-2007, 11:28 AM
#12
Guest
Posts: n/a
Re: Cj5/151 with Rochester SE2. Need Vacuum Hose Diagram
Mike: I have the Haynes manual (CJ'49-'86) and could find nothing in it.
What page?
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:45db14f9$0$2631$9a6e19ea@unlimited.newshostin g.com...
> Too bad you don't live close to Toronto, I am pretty good at figuring out
> where vacuum lines should go to.
>
> I was just looking in the Haynes CJ manual, and it does cover just about
> all of your vacuum line plumbing routing and components for the feedback
> carb's operation. It is not an expensive book and most auto stores sell
> it. Unfortunately my book is broken right at the 151 emissions section
> and is missing a few pages. I still see most of the system's setup.
>
> If you are running the full emissions package, the lines route differently
> than if you just need functioning main items.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> (More Off Road album links at bottom of the view page)
>
> MStevens003 wrote:
>> I've ben to the references here that are still live (Tom Collin's site is
>> no more) and while I have found a couple of hints for individual
>> components I am still unsure of what to do. I have found nothing that is
>> specifically for the 4cyl 151 engine with the 2SE so if anyone knows of
>> links to vacuum diagrams please post.
>>
>> Thanks Bill for what you have given I'll make the best of it until I get
>> more info. Who else here has the 151 4cyl engine? Does anyone?
>> Michael
>>
>> "L.W. (Bill) ------ III" <----------@***.net> wrote in message
>> news:45da3b47$0$16362$88260bb3@free.teranews.com.. .
>>> The one going to the choke pull-off, will be full manifold vacuum.
>>> Others is be going to devices much like the six cylinder:
>>> http://www.jedi.com/obiwan/jeep/misc/vacuumhoses.html And newer YJ:
>>> http://home.sprynet.com/~dale02/list.htm
>>> God Bless America, Bill 0|||||||0
>>> mailto:-------------------- http://www.----------.com/
>>>
>>> "MStevens003" <MSTEVENS003@dc.rr.com> wrote in message
>>> news:45da18c8$0$27081$4c368faf@roadrunner.com...
>>>> Just rebuilt the Rochester SE2 carb on my '81 CJ5. It's the 151 engine
>>>> commonly known as the "four banger". The bore is I have 5 hanging
>>>> vacuum
>>>> hoses and 7 tubes looking for hoses and no idea what goes where as all
>>>> my
>>>> marking have rubbed off. There is a vacuum hose routing diagram under
>>>> the
>>>> hood but it shows afr fewer hoses that I have hanging around and does
>>>> not
>>>> help me.
>>>>
>>>> Can someone please point me to a routing diagram? In case someone knows
>>> the
>>>> answer to this or has a simila Jeep I will list here what pipes looking
>>> for
>>>> hoses I have.
>>>>
>>>> One pipe on the choke solenoid
>>>> Three pipes on the plenum that feed straight into the the intake
>>>> manifold
>>>> just inder the carb and
>>>> Two tubes sticking out of the middle section of the carb body
>>>> One from the bottom section of the carb.
>>>>
>>>> Hope someone can help.
>>>>
>>>> Thanks
>>>>
>>>> Michael
>>>>
>>>>
>>>
>>>
>>> --
>>> Posted via a free Usenet account from http://www.teranews.com
>>>
>>
What page?
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:45db14f9$0$2631$9a6e19ea@unlimited.newshostin g.com...
> Too bad you don't live close to Toronto, I am pretty good at figuring out
> where vacuum lines should go to.
>
> I was just looking in the Haynes CJ manual, and it does cover just about
> all of your vacuum line plumbing routing and components for the feedback
> carb's operation. It is not an expensive book and most auto stores sell
> it. Unfortunately my book is broken right at the 151 emissions section
> and is missing a few pages. I still see most of the system's setup.
>
> If you are running the full emissions package, the lines route differently
> than if you just need functioning main items.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> (More Off Road album links at bottom of the view page)
>
> MStevens003 wrote:
>> I've ben to the references here that are still live (Tom Collin's site is
>> no more) and while I have found a couple of hints for individual
>> components I am still unsure of what to do. I have found nothing that is
>> specifically for the 4cyl 151 engine with the 2SE so if anyone knows of
>> links to vacuum diagrams please post.
>>
>> Thanks Bill for what you have given I'll make the best of it until I get
>> more info. Who else here has the 151 4cyl engine? Does anyone?
>> Michael
>>
>> "L.W. (Bill) ------ III" <----------@***.net> wrote in message
>> news:45da3b47$0$16362$88260bb3@free.teranews.com.. .
>>> The one going to the choke pull-off, will be full manifold vacuum.
>>> Others is be going to devices much like the six cylinder:
>>> http://www.jedi.com/obiwan/jeep/misc/vacuumhoses.html And newer YJ:
>>> http://home.sprynet.com/~dale02/list.htm
>>> God Bless America, Bill 0|||||||0
>>> mailto:-------------------- http://www.----------.com/
>>>
>>> "MStevens003" <MSTEVENS003@dc.rr.com> wrote in message
>>> news:45da18c8$0$27081$4c368faf@roadrunner.com...
>>>> Just rebuilt the Rochester SE2 carb on my '81 CJ5. It's the 151 engine
>>>> commonly known as the "four banger". The bore is I have 5 hanging
>>>> vacuum
>>>> hoses and 7 tubes looking for hoses and no idea what goes where as all
>>>> my
>>>> marking have rubbed off. There is a vacuum hose routing diagram under
>>>> the
>>>> hood but it shows afr fewer hoses that I have hanging around and does
>>>> not
>>>> help me.
>>>>
>>>> Can someone please point me to a routing diagram? In case someone knows
>>> the
>>>> answer to this or has a simila Jeep I will list here what pipes looking
>>> for
>>>> hoses I have.
>>>>
>>>> One pipe on the choke solenoid
>>>> Three pipes on the plenum that feed straight into the the intake
>>>> manifold
>>>> just inder the carb and
>>>> Two tubes sticking out of the middle section of the carb body
>>>> One from the bottom section of the carb.
>>>>
>>>> Hope someone can help.
>>>>
>>>> Thanks
>>>>
>>>> Michael
>>>>
>>>>
>>>
>>>
>>> --
>>> Posted via a free Usenet account from http://www.teranews.com
>>>
>>
02-20-2007, 11:28 AM
#13
Guest
Posts: n/a
Re: Cj5/151 with Rochester SE2. Need Vacuum Hose Diagram
Mike: I have the Haynes manual (CJ'49-'86) and could find nothing in it.
What page?
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:45db14f9$0$2631$9a6e19ea@unlimited.newshostin g.com...
> Too bad you don't live close to Toronto, I am pretty good at figuring out
> where vacuum lines should go to.
>
> I was just looking in the Haynes CJ manual, and it does cover just about
> all of your vacuum line plumbing routing and components for the feedback
> carb's operation. It is not an expensive book and most auto stores sell
> it. Unfortunately my book is broken right at the 151 emissions section
> and is missing a few pages. I still see most of the system's setup.
>
> If you are running the full emissions package, the lines route differently
> than if you just need functioning main items.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> (More Off Road album links at bottom of the view page)
>
> MStevens003 wrote:
>> I've ben to the references here that are still live (Tom Collin's site is
>> no more) and while I have found a couple of hints for individual
>> components I am still unsure of what to do. I have found nothing that is
>> specifically for the 4cyl 151 engine with the 2SE so if anyone knows of
>> links to vacuum diagrams please post.
>>
>> Thanks Bill for what you have given I'll make the best of it until I get
>> more info. Who else here has the 151 4cyl engine? Does anyone?
>> Michael
>>
>> "L.W. (Bill) ------ III" <----------@***.net> wrote in message
>> news:45da3b47$0$16362$88260bb3@free.teranews.com.. .
>>> The one going to the choke pull-off, will be full manifold vacuum.
>>> Others is be going to devices much like the six cylinder:
>>> http://www.jedi.com/obiwan/jeep/misc/vacuumhoses.html And newer YJ:
>>> http://home.sprynet.com/~dale02/list.htm
>>> God Bless America, Bill 0|||||||0
>>> mailto:-------------------- http://www.----------.com/
>>>
>>> "MStevens003" <MSTEVENS003@dc.rr.com> wrote in message
>>> news:45da18c8$0$27081$4c368faf@roadrunner.com...
>>>> Just rebuilt the Rochester SE2 carb on my '81 CJ5. It's the 151 engine
>>>> commonly known as the "four banger". The bore is I have 5 hanging
>>>> vacuum
>>>> hoses and 7 tubes looking for hoses and no idea what goes where as all
>>>> my
>>>> marking have rubbed off. There is a vacuum hose routing diagram under
>>>> the
>>>> hood but it shows afr fewer hoses that I have hanging around and does
>>>> not
>>>> help me.
>>>>
>>>> Can someone please point me to a routing diagram? In case someone knows
>>> the
>>>> answer to this or has a simila Jeep I will list here what pipes looking
>>> for
>>>> hoses I have.
>>>>
>>>> One pipe on the choke solenoid
>>>> Three pipes on the plenum that feed straight into the the intake
>>>> manifold
>>>> just inder the carb and
>>>> Two tubes sticking out of the middle section of the carb body
>>>> One from the bottom section of the carb.
>>>>
>>>> Hope someone can help.
>>>>
>>>> Thanks
>>>>
>>>> Michael
>>>>
>>>>
>>>
>>>
>>> --
>>> Posted via a free Usenet account from http://www.teranews.com
>>>
>>
What page?
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:45db14f9$0$2631$9a6e19ea@unlimited.newshostin g.com...
> Too bad you don't live close to Toronto, I am pretty good at figuring out
> where vacuum lines should go to.
>
> I was just looking in the Haynes CJ manual, and it does cover just about
> all of your vacuum line plumbing routing and components for the feedback
> carb's operation. It is not an expensive book and most auto stores sell
> it. Unfortunately my book is broken right at the 151 emissions section
> and is missing a few pages. I still see most of the system's setup.
>
> If you are running the full emissions package, the lines route differently
> than if you just need functioning main items.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> (More Off Road album links at bottom of the view page)
>
> MStevens003 wrote:
>> I've ben to the references here that are still live (Tom Collin's site is
>> no more) and while I have found a couple of hints for individual
>> components I am still unsure of what to do. I have found nothing that is
>> specifically for the 4cyl 151 engine with the 2SE so if anyone knows of
>> links to vacuum diagrams please post.
>>
>> Thanks Bill for what you have given I'll make the best of it until I get
>> more info. Who else here has the 151 4cyl engine? Does anyone?
>> Michael
>>
>> "L.W. (Bill) ------ III" <----------@***.net> wrote in message
>> news:45da3b47$0$16362$88260bb3@free.teranews.com.. .
>>> The one going to the choke pull-off, will be full manifold vacuum.
>>> Others is be going to devices much like the six cylinder:
>>> http://www.jedi.com/obiwan/jeep/misc/vacuumhoses.html And newer YJ:
>>> http://home.sprynet.com/~dale02/list.htm
>>> God Bless America, Bill 0|||||||0
>>> mailto:-------------------- http://www.----------.com/
>>>
>>> "MStevens003" <MSTEVENS003@dc.rr.com> wrote in message
>>> news:45da18c8$0$27081$4c368faf@roadrunner.com...
>>>> Just rebuilt the Rochester SE2 carb on my '81 CJ5. It's the 151 engine
>>>> commonly known as the "four banger". The bore is I have 5 hanging
>>>> vacuum
>>>> hoses and 7 tubes looking for hoses and no idea what goes where as all
>>>> my
>>>> marking have rubbed off. There is a vacuum hose routing diagram under
>>>> the
>>>> hood but it shows afr fewer hoses that I have hanging around and does
>>>> not
>>>> help me.
>>>>
>>>> Can someone please point me to a routing diagram? In case someone knows
>>> the
>>>> answer to this or has a simila Jeep I will list here what pipes looking
>>> for
>>>> hoses I have.
>>>>
>>>> One pipe on the choke solenoid
>>>> Three pipes on the plenum that feed straight into the the intake
>>>> manifold
>>>> just inder the carb and
>>>> Two tubes sticking out of the middle section of the carb body
>>>> One from the bottom section of the carb.
>>>>
>>>> Hope someone can help.
>>>>
>>>> Thanks
>>>>
>>>> Michael
>>>>
>>>>
>>>
>>>
>>> --
>>> Posted via a free Usenet account from http://www.teranews.com
>>>
>>
02-20-2007, 12:20 PM
#14
Guest
Posts: n/a
Re: Cj5/151 with Rochester SE2. Need Vacuum Hose Diagram
Here are some that I still have. Time for a new book I guess...
The various valves like the CTO and TVS and the vacuum delay units are
explained in the testing area of CH 6 by what opening should hook to what.
I have what I 'think' is a very complete vacuum schematic for the 4
banger carb engine with California emissions, basically everything, in
another XJ Haynes manual. Those pages are missing from my CJ one.
I could scan this diagram and email it to you if you would like.
Here are some I saw:
Your TAC system for the air filter is on page 6-11.
The carb feedback electric schematic is on page 6-12.
The choke pull off vacuum diagram is on page 4-22.
As far as i know unless you have an automatic or AC, the vacuum to the
idle stop is not used so that line can be ignored and plugged. Some
folks use those stop solenoids as a manual fast idle by attaching power
and a toggle switch to it's electrics.
Mike
MStevens003 wrote:
> Mike: I have the Haynes manual (CJ'49-'86) and could find nothing in it.
> What page?
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:45db14f9$0$2631$9a6e19ea@unlimited.newshostin g.com...
>> Too bad you don't live close to Toronto, I am pretty good at figuring out
>> where vacuum lines should go to.
>>
>> I was just looking in the Haynes CJ manual, and it does cover just about
>> all of your vacuum line plumbing routing and components for the feedback
>> carb's operation. It is not an expensive book and most auto stores sell
>> it. Unfortunately my book is broken right at the 151 emissions section
>> and is missing a few pages. I still see most of the system's setup.
>>
>> If you are running the full emissions package, the lines route differently
>> than if you just need functioning main items.
>>
>> Mike
>> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
>> 88 Cherokee 235 BFG AT's
>> Canadian Off Road Trips Photos: Non members can still view!
>> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
>> (More Off Road album links at bottom of the view page)
>>
>> MStevens003 wrote:
>>> I've ben to the references here that are still live (Tom Collin's site is
>>> no more) and while I have found a couple of hints for individual
>>> components I am still unsure of what to do. I have found nothing that is
>>> specifically for the 4cyl 151 engine with the 2SE so if anyone knows of
>>> links to vacuum diagrams please post.
>>>
>>> Thanks Bill for what you have given I'll make the best of it until I get
>>> more info. Who else here has the 151 4cyl engine? Does anyone?
>>> Michael
>>>
>>> "L.W. (Bill) ------ III" <----------@***.net> wrote in message
>>> news:45da3b47$0$16362$88260bb3@free.teranews.com.. .
>>>> The one going to the choke pull-off, will be full manifold vacuum.
>>>> Others is be going to devices much like the six cylinder:
>>>> http://www.jedi.com/obiwan/jeep/misc/vacuumhoses.html And newer YJ:
>>>> http://home.sprynet.com/~dale02/list.htm
>>>> God Bless America, Bill 0|||||||0
>>>> mailto:-------------------- http://www.----------.com/
>>>>
>>>> "MStevens003" <MSTEVENS003@dc.rr.com> wrote in message
>>>> news:45da18c8$0$27081$4c368faf@roadrunner.com...
>>>>> Just rebuilt the Rochester SE2 carb on my '81 CJ5. It's the 151 engine
>>>>> commonly known as the "four banger". The bore is I have 5 hanging
>>>>> vacuum
>>>>> hoses and 7 tubes looking for hoses and no idea what goes where as all
>>>>> my
>>>>> marking have rubbed off. There is a vacuum hose routing diagram under
>>>>> the
>>>>> hood but it shows afr fewer hoses that I have hanging around and does
>>>>> not
>>>>> help me.
>>>>>
>>>>> Can someone please point me to a routing diagram? In case someone knows
>>>> the
>>>>> answer to this or has a simila Jeep I will list here what pipes looking
>>>> for
>>>>> hoses I have.
>>>>>
>>>>> One pipe on the choke solenoid
>>>>> Three pipes on the plenum that feed straight into the the intake
>>>>> manifold
>>>>> just inder the carb and
>>>>> Two tubes sticking out of the middle section of the carb body
>>>>> One from the bottom section of the carb.
>>>>>
>>>>> Hope someone can help.
>>>>>
>>>>> Thanks
>>>>>
>>>>> Michael
>>>>>
>>>>>
>>>>
>>>> --
>>>> Posted via a free Usenet account from http://www.teranews.com
>>>>
>
The various valves like the CTO and TVS and the vacuum delay units are
explained in the testing area of CH 6 by what opening should hook to what.
I have what I 'think' is a very complete vacuum schematic for the 4
banger carb engine with California emissions, basically everything, in
another XJ Haynes manual. Those pages are missing from my CJ one.
I could scan this diagram and email it to you if you would like.
Here are some I saw:
Your TAC system for the air filter is on page 6-11.
The carb feedback electric schematic is on page 6-12.
The choke pull off vacuum diagram is on page 4-22.
As far as i know unless you have an automatic or AC, the vacuum to the
idle stop is not used so that line can be ignored and plugged. Some
folks use those stop solenoids as a manual fast idle by attaching power
and a toggle switch to it's electrics.
Mike
MStevens003 wrote:
> Mike: I have the Haynes manual (CJ'49-'86) and could find nothing in it.
> What page?
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:45db14f9$0$2631$9a6e19ea@unlimited.newshostin g.com...
>> Too bad you don't live close to Toronto, I am pretty good at figuring out
>> where vacuum lines should go to.
>>
>> I was just looking in the Haynes CJ manual, and it does cover just about
>> all of your vacuum line plumbing routing and components for the feedback
>> carb's operation. It is not an expensive book and most auto stores sell
>> it. Unfortunately my book is broken right at the 151 emissions section
>> and is missing a few pages. I still see most of the system's setup.
>>
>> If you are running the full emissions package, the lines route differently
>> than if you just need functioning main items.
>>
>> Mike
>> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
>> 88 Cherokee 235 BFG AT's
>> Canadian Off Road Trips Photos: Non members can still view!
>> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
>> (More Off Road album links at bottom of the view page)
>>
>> MStevens003 wrote:
>>> I've ben to the references here that are still live (Tom Collin's site is
>>> no more) and while I have found a couple of hints for individual
>>> components I am still unsure of what to do. I have found nothing that is
>>> specifically for the 4cyl 151 engine with the 2SE so if anyone knows of
>>> links to vacuum diagrams please post.
>>>
>>> Thanks Bill for what you have given I'll make the best of it until I get
>>> more info. Who else here has the 151 4cyl engine? Does anyone?
>>> Michael
>>>
>>> "L.W. (Bill) ------ III" <----------@***.net> wrote in message
>>> news:45da3b47$0$16362$88260bb3@free.teranews.com.. .
>>>> The one going to the choke pull-off, will be full manifold vacuum.
>>>> Others is be going to devices much like the six cylinder:
>>>> http://www.jedi.com/obiwan/jeep/misc/vacuumhoses.html And newer YJ:
>>>> http://home.sprynet.com/~dale02/list.htm
>>>> God Bless America, Bill 0|||||||0
>>>> mailto:-------------------- http://www.----------.com/
>>>>
>>>> "MStevens003" <MSTEVENS003@dc.rr.com> wrote in message
>>>> news:45da18c8$0$27081$4c368faf@roadrunner.com...
>>>>> Just rebuilt the Rochester SE2 carb on my '81 CJ5. It's the 151 engine
>>>>> commonly known as the "four banger". The bore is I have 5 hanging
>>>>> vacuum
>>>>> hoses and 7 tubes looking for hoses and no idea what goes where as all
>>>>> my
>>>>> marking have rubbed off. There is a vacuum hose routing diagram under
>>>>> the
>>>>> hood but it shows afr fewer hoses that I have hanging around and does
>>>>> not
>>>>> help me.
>>>>>
>>>>> Can someone please point me to a routing diagram? In case someone knows
>>>> the
>>>>> answer to this or has a simila Jeep I will list here what pipes looking
>>>> for
>>>>> hoses I have.
>>>>>
>>>>> One pipe on the choke solenoid
>>>>> Three pipes on the plenum that feed straight into the the intake
>>>>> manifold
>>>>> just inder the carb and
>>>>> Two tubes sticking out of the middle section of the carb body
>>>>> One from the bottom section of the carb.
>>>>>
>>>>> Hope someone can help.
>>>>>
>>>>> Thanks
>>>>>
>>>>> Michael
>>>>>
>>>>>
>>>>
>>>> --
>>>> Posted via a free Usenet account from http://www.teranews.com
>>>>
>
02-20-2007, 12:20 PM
#15
Guest
Posts: n/a
Re: Cj5/151 with Rochester SE2. Need Vacuum Hose Diagram
Here are some that I still have. Time for a new book I guess...
The various valves like the CTO and TVS and the vacuum delay units are
explained in the testing area of CH 6 by what opening should hook to what.
I have what I 'think' is a very complete vacuum schematic for the 4
banger carb engine with California emissions, basically everything, in
another XJ Haynes manual. Those pages are missing from my CJ one.
I could scan this diagram and email it to you if you would like.
Here are some I saw:
Your TAC system for the air filter is on page 6-11.
The carb feedback electric schematic is on page 6-12.
The choke pull off vacuum diagram is on page 4-22.
As far as i know unless you have an automatic or AC, the vacuum to the
idle stop is not used so that line can be ignored and plugged. Some
folks use those stop solenoids as a manual fast idle by attaching power
and a toggle switch to it's electrics.
Mike
MStevens003 wrote:
> Mike: I have the Haynes manual (CJ'49-'86) and could find nothing in it.
> What page?
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:45db14f9$0$2631$9a6e19ea@unlimited.newshostin g.com...
>> Too bad you don't live close to Toronto, I am pretty good at figuring out
>> where vacuum lines should go to.
>>
>> I was just looking in the Haynes CJ manual, and it does cover just about
>> all of your vacuum line plumbing routing and components for the feedback
>> carb's operation. It is not an expensive book and most auto stores sell
>> it. Unfortunately my book is broken right at the 151 emissions section
>> and is missing a few pages. I still see most of the system's setup.
>>
>> If you are running the full emissions package, the lines route differently
>> than if you just need functioning main items.
>>
>> Mike
>> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
>> 88 Cherokee 235 BFG AT's
>> Canadian Off Road Trips Photos: Non members can still view!
>> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
>> (More Off Road album links at bottom of the view page)
>>
>> MStevens003 wrote:
>>> I've ben to the references here that are still live (Tom Collin's site is
>>> no more) and while I have found a couple of hints for individual
>>> components I am still unsure of what to do. I have found nothing that is
>>> specifically for the 4cyl 151 engine with the 2SE so if anyone knows of
>>> links to vacuum diagrams please post.
>>>
>>> Thanks Bill for what you have given I'll make the best of it until I get
>>> more info. Who else here has the 151 4cyl engine? Does anyone?
>>> Michael
>>>
>>> "L.W. (Bill) ------ III" <----------@***.net> wrote in message
>>> news:45da3b47$0$16362$88260bb3@free.teranews.com.. .
>>>> The one going to the choke pull-off, will be full manifold vacuum.
>>>> Others is be going to devices much like the six cylinder:
>>>> http://www.jedi.com/obiwan/jeep/misc/vacuumhoses.html And newer YJ:
>>>> http://home.sprynet.com/~dale02/list.htm
>>>> God Bless America, Bill 0|||||||0
>>>> mailto:-------------------- http://www.----------.com/
>>>>
>>>> "MStevens003" <MSTEVENS003@dc.rr.com> wrote in message
>>>> news:45da18c8$0$27081$4c368faf@roadrunner.com...
>>>>> Just rebuilt the Rochester SE2 carb on my '81 CJ5. It's the 151 engine
>>>>> commonly known as the "four banger". The bore is I have 5 hanging
>>>>> vacuum
>>>>> hoses and 7 tubes looking for hoses and no idea what goes where as all
>>>>> my
>>>>> marking have rubbed off. There is a vacuum hose routing diagram under
>>>>> the
>>>>> hood but it shows afr fewer hoses that I have hanging around and does
>>>>> not
>>>>> help me.
>>>>>
>>>>> Can someone please point me to a routing diagram? In case someone knows
>>>> the
>>>>> answer to this or has a simila Jeep I will list here what pipes looking
>>>> for
>>>>> hoses I have.
>>>>>
>>>>> One pipe on the choke solenoid
>>>>> Three pipes on the plenum that feed straight into the the intake
>>>>> manifold
>>>>> just inder the carb and
>>>>> Two tubes sticking out of the middle section of the carb body
>>>>> One from the bottom section of the carb.
>>>>>
>>>>> Hope someone can help.
>>>>>
>>>>> Thanks
>>>>>
>>>>> Michael
>>>>>
>>>>>
>>>>
>>>> --
>>>> Posted via a free Usenet account from http://www.teranews.com
>>>>
>
The various valves like the CTO and TVS and the vacuum delay units are
explained in the testing area of CH 6 by what opening should hook to what.
I have what I 'think' is a very complete vacuum schematic for the 4
banger carb engine with California emissions, basically everything, in
another XJ Haynes manual. Those pages are missing from my CJ one.
I could scan this diagram and email it to you if you would like.
Here are some I saw:
Your TAC system for the air filter is on page 6-11.
The carb feedback electric schematic is on page 6-12.
The choke pull off vacuum diagram is on page 4-22.
As far as i know unless you have an automatic or AC, the vacuum to the
idle stop is not used so that line can be ignored and plugged. Some
folks use those stop solenoids as a manual fast idle by attaching power
and a toggle switch to it's electrics.
Mike
MStevens003 wrote:
> Mike: I have the Haynes manual (CJ'49-'86) and could find nothing in it.
> What page?
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:45db14f9$0$2631$9a6e19ea@unlimited.newshostin g.com...
>> Too bad you don't live close to Toronto, I am pretty good at figuring out
>> where vacuum lines should go to.
>>
>> I was just looking in the Haynes CJ manual, and it does cover just about
>> all of your vacuum line plumbing routing and components for the feedback
>> carb's operation. It is not an expensive book and most auto stores sell
>> it. Unfortunately my book is broken right at the 151 emissions section
>> and is missing a few pages. I still see most of the system's setup.
>>
>> If you are running the full emissions package, the lines route differently
>> than if you just need functioning main items.
>>
>> Mike
>> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
>> 88 Cherokee 235 BFG AT's
>> Canadian Off Road Trips Photos: Non members can still view!
>> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
>> (More Off Road album links at bottom of the view page)
>>
>> MStevens003 wrote:
>>> I've ben to the references here that are still live (Tom Collin's site is
>>> no more) and while I have found a couple of hints for individual
>>> components I am still unsure of what to do. I have found nothing that is
>>> specifically for the 4cyl 151 engine with the 2SE so if anyone knows of
>>> links to vacuum diagrams please post.
>>>
>>> Thanks Bill for what you have given I'll make the best of it until I get
>>> more info. Who else here has the 151 4cyl engine? Does anyone?
>>> Michael
>>>
>>> "L.W. (Bill) ------ III" <----------@***.net> wrote in message
>>> news:45da3b47$0$16362$88260bb3@free.teranews.com.. .
>>>> The one going to the choke pull-off, will be full manifold vacuum.
>>>> Others is be going to devices much like the six cylinder:
>>>> http://www.jedi.com/obiwan/jeep/misc/vacuumhoses.html And newer YJ:
>>>> http://home.sprynet.com/~dale02/list.htm
>>>> God Bless America, Bill 0|||||||0
>>>> mailto:-------------------- http://www.----------.com/
>>>>
>>>> "MStevens003" <MSTEVENS003@dc.rr.com> wrote in message
>>>> news:45da18c8$0$27081$4c368faf@roadrunner.com...
>>>>> Just rebuilt the Rochester SE2 carb on my '81 CJ5. It's the 151 engine
>>>>> commonly known as the "four banger". The bore is I have 5 hanging
>>>>> vacuum
>>>>> hoses and 7 tubes looking for hoses and no idea what goes where as all
>>>>> my
>>>>> marking have rubbed off. There is a vacuum hose routing diagram under
>>>>> the
>>>>> hood but it shows afr fewer hoses that I have hanging around and does
>>>>> not
>>>>> help me.
>>>>>
>>>>> Can someone please point me to a routing diagram? In case someone knows
>>>> the
>>>>> answer to this or has a simila Jeep I will list here what pipes looking
>>>> for
>>>>> hoses I have.
>>>>>
>>>>> One pipe on the choke solenoid
>>>>> Three pipes on the plenum that feed straight into the the intake
>>>>> manifold
>>>>> just inder the carb and
>>>>> Two tubes sticking out of the middle section of the carb body
>>>>> One from the bottom section of the carb.
>>>>>
>>>>> Hope someone can help.
>>>>>
>>>>> Thanks
>>>>>
>>>>> Michael
>>>>>
>>>>>
>>>>
>>>> --
>>>> Posted via a free Usenet account from http://www.teranews.com
>>>>
>
02-20-2007, 12:20 PM
#16
Guest
Posts: n/a
Re: Cj5/151 with Rochester SE2. Need Vacuum Hose Diagram
Here are some that I still have. Time for a new book I guess...
The various valves like the CTO and TVS and the vacuum delay units are
explained in the testing area of CH 6 by what opening should hook to what.
I have what I 'think' is a very complete vacuum schematic for the 4
banger carb engine with California emissions, basically everything, in
another XJ Haynes manual. Those pages are missing from my CJ one.
I could scan this diagram and email it to you if you would like.
Here are some I saw:
Your TAC system for the air filter is on page 6-11.
The carb feedback electric schematic is on page 6-12.
The choke pull off vacuum diagram is on page 4-22.
As far as i know unless you have an automatic or AC, the vacuum to the
idle stop is not used so that line can be ignored and plugged. Some
folks use those stop solenoids as a manual fast idle by attaching power
and a toggle switch to it's electrics.
Mike
MStevens003 wrote:
> Mike: I have the Haynes manual (CJ'49-'86) and could find nothing in it.
> What page?
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:45db14f9$0$2631$9a6e19ea@unlimited.newshostin g.com...
>> Too bad you don't live close to Toronto, I am pretty good at figuring out
>> where vacuum lines should go to.
>>
>> I was just looking in the Haynes CJ manual, and it does cover just about
>> all of your vacuum line plumbing routing and components for the feedback
>> carb's operation. It is not an expensive book and most auto stores sell
>> it. Unfortunately my book is broken right at the 151 emissions section
>> and is missing a few pages. I still see most of the system's setup.
>>
>> If you are running the full emissions package, the lines route differently
>> than if you just need functioning main items.
>>
>> Mike
>> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
>> 88 Cherokee 235 BFG AT's
>> Canadian Off Road Trips Photos: Non members can still view!
>> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
>> (More Off Road album links at bottom of the view page)
>>
>> MStevens003 wrote:
>>> I've ben to the references here that are still live (Tom Collin's site is
>>> no more) and while I have found a couple of hints for individual
>>> components I am still unsure of what to do. I have found nothing that is
>>> specifically for the 4cyl 151 engine with the 2SE so if anyone knows of
>>> links to vacuum diagrams please post.
>>>
>>> Thanks Bill for what you have given I'll make the best of it until I get
>>> more info. Who else here has the 151 4cyl engine? Does anyone?
>>> Michael
>>>
>>> "L.W. (Bill) ------ III" <----------@***.net> wrote in message
>>> news:45da3b47$0$16362$88260bb3@free.teranews.com.. .
>>>> The one going to the choke pull-off, will be full manifold vacuum.
>>>> Others is be going to devices much like the six cylinder:
>>>> http://www.jedi.com/obiwan/jeep/misc/vacuumhoses.html And newer YJ:
>>>> http://home.sprynet.com/~dale02/list.htm
>>>> God Bless America, Bill 0|||||||0
>>>> mailto:-------------------- http://www.----------.com/
>>>>
>>>> "MStevens003" <MSTEVENS003@dc.rr.com> wrote in message
>>>> news:45da18c8$0$27081$4c368faf@roadrunner.com...
>>>>> Just rebuilt the Rochester SE2 carb on my '81 CJ5. It's the 151 engine
>>>>> commonly known as the "four banger". The bore is I have 5 hanging
>>>>> vacuum
>>>>> hoses and 7 tubes looking for hoses and no idea what goes where as all
>>>>> my
>>>>> marking have rubbed off. There is a vacuum hose routing diagram under
>>>>> the
>>>>> hood but it shows afr fewer hoses that I have hanging around and does
>>>>> not
>>>>> help me.
>>>>>
>>>>> Can someone please point me to a routing diagram? In case someone knows
>>>> the
>>>>> answer to this or has a simila Jeep I will list here what pipes looking
>>>> for
>>>>> hoses I have.
>>>>>
>>>>> One pipe on the choke solenoid
>>>>> Three pipes on the plenum that feed straight into the the intake
>>>>> manifold
>>>>> just inder the carb and
>>>>> Two tubes sticking out of the middle section of the carb body
>>>>> One from the bottom section of the carb.
>>>>>
>>>>> Hope someone can help.
>>>>>
>>>>> Thanks
>>>>>
>>>>> Michael
>>>>>
>>>>>
>>>>
>>>> --
>>>> Posted via a free Usenet account from http://www.teranews.com
>>>>
>
The various valves like the CTO and TVS and the vacuum delay units are
explained in the testing area of CH 6 by what opening should hook to what.
I have what I 'think' is a very complete vacuum schematic for the 4
banger carb engine with California emissions, basically everything, in
another XJ Haynes manual. Those pages are missing from my CJ one.
I could scan this diagram and email it to you if you would like.
Here are some I saw:
Your TAC system for the air filter is on page 6-11.
The carb feedback electric schematic is on page 6-12.
The choke pull off vacuum diagram is on page 4-22.
As far as i know unless you have an automatic or AC, the vacuum to the
idle stop is not used so that line can be ignored and plugged. Some
folks use those stop solenoids as a manual fast idle by attaching power
and a toggle switch to it's electrics.
Mike
MStevens003 wrote:
> Mike: I have the Haynes manual (CJ'49-'86) and could find nothing in it.
> What page?
>
> "Mike Romain" <romainm@sympatico.ca> wrote in message
> news:45db14f9$0$2631$9a6e19ea@unlimited.newshostin g.com...
>> Too bad you don't live close to Toronto, I am pretty good at figuring out
>> where vacuum lines should go to.
>>
>> I was just looking in the Haynes CJ manual, and it does cover just about
>> all of your vacuum line plumbing routing and components for the feedback
>> carb's operation. It is not an expensive book and most auto stores sell
>> it. Unfortunately my book is broken right at the 151 emissions section
>> and is missing a few pages. I still see most of the system's setup.
>>
>> If you are running the full emissions package, the lines route differently
>> than if you just need functioning main items.
>>
>> Mike
>> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
>> 88 Cherokee 235 BFG AT's
>> Canadian Off Road Trips Photos: Non members can still view!
>> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
>> (More Off Road album links at bottom of the view page)
>>
>> MStevens003 wrote:
>>> I've ben to the references here that are still live (Tom Collin's site is
>>> no more) and while I have found a couple of hints for individual
>>> components I am still unsure of what to do. I have found nothing that is
>>> specifically for the 4cyl 151 engine with the 2SE so if anyone knows of
>>> links to vacuum diagrams please post.
>>>
>>> Thanks Bill for what you have given I'll make the best of it until I get
>>> more info. Who else here has the 151 4cyl engine? Does anyone?
>>> Michael
>>>
>>> "L.W. (Bill) ------ III" <----------@***.net> wrote in message
>>> news:45da3b47$0$16362$88260bb3@free.teranews.com.. .
>>>> The one going to the choke pull-off, will be full manifold vacuum.
>>>> Others is be going to devices much like the six cylinder:
>>>> http://www.jedi.com/obiwan/jeep/misc/vacuumhoses.html And newer YJ:
>>>> http://home.sprynet.com/~dale02/list.htm
>>>> God Bless America, Bill 0|||||||0
>>>> mailto:-------------------- http://www.----------.com/
>>>>
>>>> "MStevens003" <MSTEVENS003@dc.rr.com> wrote in message
>>>> news:45da18c8$0$27081$4c368faf@roadrunner.com...
>>>>> Just rebuilt the Rochester SE2 carb on my '81 CJ5. It's the 151 engine
>>>>> commonly known as the "four banger". The bore is I have 5 hanging
>>>>> vacuum
>>>>> hoses and 7 tubes looking for hoses and no idea what goes where as all
>>>>> my
>>>>> marking have rubbed off. There is a vacuum hose routing diagram under
>>>>> the
>>>>> hood but it shows afr fewer hoses that I have hanging around and does
>>>>> not
>>>>> help me.
>>>>>
>>>>> Can someone please point me to a routing diagram? In case someone knows
>>>> the
>>>>> answer to this or has a simila Jeep I will list here what pipes looking
>>>> for
>>>>> hoses I have.
>>>>>
>>>>> One pipe on the choke solenoid
>>>>> Three pipes on the plenum that feed straight into the the intake
>>>>> manifold
>>>>> just inder the carb and
>>>>> Two tubes sticking out of the middle section of the carb body
>>>>> One from the bottom section of the carb.
>>>>>
>>>>> Hope someone can help.
>>>>>
>>>>> Thanks
>>>>>
>>>>> Michael
>>>>>
>>>>>
>>>>
>>>> --
>>>> Posted via a free Usenet account from http://www.teranews.com
>>>>
>
02-20-2007, 12:41 PM
#17
Guest
Posts: n/a
Re: Cj5/151 with Rochester SE2. Need Vacuum Hose Diagram
Oh, I have the Canadian emissions diagram for the 4 banger too. Those
damn things have more vacuum lines than the 258 which I thought was
insane.....
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
damn things have more vacuum lines than the 258 which I thought was
insane.....
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
02-20-2007, 12:41 PM
#18
Guest
Posts: n/a
Re: Cj5/151 with Rochester SE2. Need Vacuum Hose Diagram
Oh, I have the Canadian emissions diagram for the 4 banger too. Those
damn things have more vacuum lines than the 258 which I thought was
insane.....
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
damn things have more vacuum lines than the 258 which I thought was
insane.....
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
02-20-2007, 12:41 PM
#19
Guest
Posts: n/a
Re: Cj5/151 with Rochester SE2. Need Vacuum Hose Diagram
Oh, I have the Canadian emissions diagram for the 4 banger too. Those
damn things have more vacuum lines than the 258 which I thought was
insane.....
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
damn things have more vacuum lines than the 258 which I thought was
insane.....
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
02-20-2007, 12:59 PM
#20
Guest
Posts: n/a
Re: Cj5/151 with Rochester SE2. Need Vacuum Hose Diagram
Need more coffee... have the 49 state diagram as well as the Ca. and CA
one also.
Mike
Mike Romain wrote:
> Oh, I have the Canadian emissions diagram for the 4 banger too. Those
> damn things have more vacuum lines than the 258 which I thought was
> insane.....
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> (More Off Road album links at bottom of the view page)
one also.
Mike
Mike Romain wrote:
> Oh, I have the Canadian emissions diagram for the 4 banger too. Those
> damn things have more vacuum lines than the 258 which I thought was
> insane.....
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
> Canadian Off Road Trips Photos: Non members can still view!
> Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
> (More Off Road album links at bottom of the view page)
